The attached_to_8255 variable in the private data is used as a flag
to indicate that the 8255 subdevice has been initialized. The call
to subdev_8255_cleanup only requires that the dev->subdevices pointer
is valid. Change the test in the detach function and remove the
attached_to_8255 variable.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The boardinfo struct and associated code is no longer needed
by this driver. Remove it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This board always has 6, 16-bit analog outputs. There is no need to carry
this information in the boardinfo. Remove it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The base address of the card is always found in pci resource 3. There is
no need to carry this information in the boardinfo. The reg_sz is not
used in the driver. Remove them.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The 8255 device is located at a fixed offset from the base
address of the card. There is not need to carry this offset
in the boardinfo. Remove it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add defines for the register map of the card.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The cards supported by this driver always have 8255 compatible
device. Remove the dio_chans variable from the private data and
always initialize the 8255 subdevice.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The digital i/o on this card is handled by an 8255 compatible
device. There are not other options. Remove the DIO_METHODS
enum as well as the dio_method variable in the boardinfo and
the code dealing with it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The dio_registers variable in the private data is only used to
pass the base address to the 8255 subdevice. Remove the variable
from the private data and pass the value directly to the
subdev_8255_init() function.

Make sure to check the return from subdev_8255_init(). That
function can fail. For aesthetic reasons, rename the local
variable 'err' to 'ret'.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the hw_dev pointer in the comed_device struct to hold the
pci_dev instead of carrying it in the private data.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use dev->iobase for the pci i/o address instead of carrying it
in the private data.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Make cb_pcimdda_probe() return the pointer to the found pci_dev
and move the comedi_pci_enable() call into the 'attach' function.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The structs, static data, and functions in this driver have
pretty generic names. Add namespace to everything to prevent
any problems.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Move a couple of the functions in order to remove the need for
the forward declarations.

Also, remove the unnecessary comments.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

These macros rely on a local variable having a specific name.
Remove them and use the comedi_board() helper to get the thisboard
pointer.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The REG_SZ macro isn't being use. Both macros use the 'thisboard'
macro which relys on a local variable having a specific name.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Convert this PCI driver to use the comedi PCI auto config attach
mechanism by adding an 'attach_pci' callback function. Since the
driver does not require any external configuration options, and
the legacy 'attach' callback is now optional, remove it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Move a couple of the functions in order to remove the need for
the forward declarations.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

These macros rely on a local variable having a specific name.
Remove them and use the comedi_board() helper to get the thisboard
pointer.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Convert this PCI driver to use the comedi PCI auto config attach
mechanism by adding an 'attach_pci' callback function. Since the
driver does not require any external configuration options, and
the legacy 'attach' callback is now optional, remove it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Move a couple of the functions in order to remove the need for
the forward declarations.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

These macros rely on a local variable having a specific name.
Remove them and use the comedi_board() helper to get the thisboard
pointer.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Convert this PCI driver to use the comedi PCI auto config attach
mechanism by adding an 'attach_pci' callback function. Since the
driver does not require any external configuration options, and
the legacy 'attach' callback is now optional, remove it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This macro relies on a local variable having a specific name.
Remove it and use the comedi_board() helper to get the pointer.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Convert this PCI driver to use the comedi PCI auto config attach
mechanism by adding an 'attach_pci' callback function. Since the
driver does not require any external configuration options, and
the legacy 'attach' callback is now optional, remove it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Convert this PCI driver to use the comedi PCI auto config attach
mechanism by adding an 'attach_pci' callback function. Since the
driver does not require any external configuration options, and
the legacy 'attach' callback is now optional, remove it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver uses the 'attach_pci' callback to attach the pci device
to the comedi subsystem. Since the 'attach' callback is now optional
it can be removed from the driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver uses the 'attach_pci' callback to attach the pci device
to the comedi subsystem. Since the 'attach' callback is now optional
it can be removed from the driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver uses the 'attach_pci' callback to attach the pci device
to the comedi subsystem. Since the 'attach' callback is now optional
it can be removed from the driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 8cb05f4b (staging:
tidspbridge: eliminate uuid_uuid_to_string), not only broke
compilation but also functionality for tidspbridge driver.

So:
- Replace remaining instances of uuid_uuid_to_string with snprintf
  to fix compilation.
- Fix the format from %pU to %pUL.
- Since these UUIDs are used in the firmware to reference section
  names, the firmware doesn't follow the standard uuid delimiter '-'
  it uses '_' instead. The driver can follow the standard convention
  however for dsp sections we must transform the uuid to what is
  expected by the firmware. E.g.:

  tidspbridge sees: 24BC8D90-BB45-11D4-B756-006008BDB66F
  firmware expects: .24BC8D90_BB45_11D4_B756_006008BDB66F
Signed-off-by: Omar Ramirez Luna <omar.ramirez@copitl.com>
CC: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'iio-for-v3.7a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next

First set of IIO rework and new drivers for 3.7 cycle.

New MXS adc driver form Marek Vasut with a minor addition
to the example code to support 4 byte reads.

First of I suspect many devm conversion patches form Julia Lawall
Some module_platform_driver uses that somehow got missed the
first time around.

Couple of other useful cleanups.

This driver is very basic. It supports userland trigger, buffer and
raw access to channels. The support for delay channels is missing
altogether.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Juergen Beisert <jbe@pengutronix.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Wolfgang Denk <wd@denx.de>

Add unsigned 32bit-wide reads into the generic-buffer.c
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Juergen Beisert <jbe@pengutronix.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

The various devm_ functions allocate memory that is released when a driver
detaches.  This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.

The call to platform_get_resource(pdev, IORESOURCE_MEM, 0) is moved coser
to the call to devm_request_and_ioremap, which is th first use of the
result of platform_get_resource.

This does not use devm_request_irq to ensure that free_irq is executed
before its idev argument is freed.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This change tries to achieve the removal of the csr driver defined snprintf
and uses the kernel defined snprintf.

After this change i got following build warnings, which are solved in this patch

warnings generated:

drivers/staging/csr/io.c:929:13: warning: format ‘%lu’ expects type ‘long unsigned int’, but argument 4 has type ‘u32’
drivers/staging/csr/io.c:929:13: warning: format ‘%lu’ expects type ‘long unsigned int’, but argument 5 has type ‘u32’
drivers/staging/csr/csr_wifi_hip_udi.c: In function ‘unifi_print_status’:
drivers/staging/csr/csr_wifi_hip_udi.c:78:27: warning: format ‘%lu’ expects type ‘long unsigned int’, but argument 4 has type ‘u32’
drivers/staging/csr/csr_wifi_hip_udi.c:151:27: warning: format ‘%u’ expects type ‘unsigned int’, but argument 5 has type ‘long int’
drivers/staging/csr/csr_wifi_hip_udi.c:257:27: warning: format ‘%lu’ expects type ‘long unsigned int’, but argument 4 has type ‘u32’
drivers/staging/csr/csr_wifi_hip_udi.c:257:27: warning: format ‘%lu’ expects type ‘long unsigned int’, but argument 5 has type ‘u32’
drivers/staging/csr/csr_wifi_hip_udi.c:261:27: warning: format ‘%lu’ expects type ‘long unsigned int’, but argument 4 has type ‘u32’
Signed-off-by: Devendra Naga <develkernel412222@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Replace the printk() calls in the comedi core module with something more
suitable, such as dev_...() or pr_...().  Remove the ones that report a
failure to increment a module count (try_module_get() failure).  Change
the printk() call in the DPRINTK() macro to pr_debug().

TODO: Most of the DPRINTK() calls need to be replaced with something
else.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The IS_ENABLED(CONFIG_COMEDI_AMPLC_PC236_ISA) and
IS_ENABLED(CONFIG_COMEDI_AMPLC_PC236_PCI) macro calls are a bit
long-winded.  Define a couple of macros DO_ISA and DO_PCI as
abbreviations for them.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The PCI-local bridge LCR registers are (assumed to be) present and used
iff the board is a PCI board (a PCI236).  Currently the code tests if
devpriv->lcr_iobase is valid before accessing the registers.  Instead,
check if the board is a PCI board and assume devpriv->lcr_iobase is
valid if so.  (Currently, no validity check is performed as the PCI
vendor and device ID ought to suffice, but simple checks could be added
when attaching the device.)
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When detaching the device in pc236_detach() mirror the bus type checks
performed by pc236_attach().  The existing tests are safe but rely on
dev->iobase being 0 when comedi_to_pci_dev(dev) is NULL.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add inline helper function is_isa_board(board) to check if the driver
supports ISA boards and this is an ISA board, and is_pci_board(board) to
check if the driver supports PCI boards and this is a PCI board.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>