Improve current RSS configuration:
 * Use netdev_rss_key instead of keeping a local copy.
 * Configure also UDP hashing to have UDP traffic spread across queues.
 * Do not direct RSS traffic to our fallback queue.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

We want to request an interrupt vector for RSS queue per CPU,
one vector for fallback queue, and one for non-rx interrupts.
Future patch will make sure that no RSS traffic is directed to
fallback queue.
This will enable us to enable fast path on traffic that otherwise
would have been received on the fallback queue.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The driver can read the current state during D0I3,
therefore there is no reason not to do it.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

For some reason, this was defined as a signed variable.
Make it unsigned.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Auxilary station ID in flag in scan config command wasn't set
although we set the station ID. Add the flag.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Currently the code checks if hardware reported both L4 and L3
checksums as valid, and only then reports it as validated to
the stack.
However, IPv6 does not have checksum at all and the L3 checksum
valid bit is always off for IPv6 packets, with the result of the
stack re-validating L4 checksum.
Fix code to set CHECKSUM_UNNECESSARY also for IPv6 packets whose
TCP/UDP checksum was verified.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Use alloc_ordered_workqueue() to allocate the workqueue instead of
create_singlethread_workqueue() since the latter is deprecated and is scheduled
for removal.

There are work items doing related operations that shouldn't be swapped when
queued in a certain order hence preserve the strict execution ordering of a
single threaded (ST) workqueue by switching to alloc_ordered_workqueue().

WQ_MEM_RECLAIM flag is not needed since the worker is not depended
during memory reclaim.
Signed-off-by: Eva Rachel Retuya <eraretuya@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

API version lower than 16 is not supported anymore - don't
load older ucode.
Remove code handling older versions.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Gscan capabilities were updated with new capabilities supported
by the device. Update GSCAN capabilities TLV.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

We have a module parameter, this is enough.
per platform customizations will be done through the init
script of the platform.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Due to hardware bug, upon any shadow free-queue register write
access, a legacy RBD shadow register must be written as well.
This is required in order to trigger a copy of the shadow registers
values after MAC exits sleep state.
Specifically, the driver has to write (any value) to the legacy RBD
register each time FRBDCB is accessed.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

"DQA" is shorthand for "dynamic queue allocation". This
enables on-demand allocation of queues per RA/TID rather than
statically allocating per vif, thus allowing a potential
benefit of various factors.

Please refer to the DOC section this patch adds to sta.h to
see a more in-depth explanation of this feature.

There are many things to take into consideration when working
in DQA mode, and this patch is only one in a series. Note that
default operation mode is non-DQA mode, unless the FW
indicates that it supports DQA mode.

This patch enables support of DQA for a station connected to
an AP, and works in a non-aggregated mode.

When a frame for an unused RA/TID arrives at the driver, it
isn't TXed immediately, but deferred first until a suitable
queue is first allocated for it, and then TXed by a worker
that both allocates the queues and TXes deferred traffic.

When a STA is removed, its queues goes back into the queue
pools for reuse as needed.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

"is_data_qos == true" is equivalent to "tid < IWL_MAX_TID_COUNT"
since tid is only assigned (and range-checked) in that case.

This removes a (harmless) smatch warning that occurs because it
can't seem to follow the above logic from the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Update device id and FW serial number for 2X2 antenna devices
in 9000 generation product. These will not be available on
the market in the coming year.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This allows to disable uapsd for BSS only, or P2P client
separately. Remove the now unneeded
IWL_MVM_P2P_UAPSD_STANDALONE constant.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

iwlwifi / iwlmvm didn't destroy their mutexes. Fix that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

TX CMD API has changed to support offload assist.
Currently we do not enable checksum yet, but must set the
padding indication, to avoid FW errors.
Set other amsdu flag as well.
The rest of the flags will be configured only if HW csum
is enabled and will be set in future patches.
This change is backward compatible.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

We insert padding if the MAC header's size is not a multiple of 4
to ensure that the SNAP header is DWORD aligned. When we do so, we
let the firmware know by setting a bit in Tx command
(TX_CMD_FLG_MH_PAD) which will instruct the firmware to drop those
2 bytes before sending the frame.
However, this is not needed for AMSDU as the sub frame header (14B)
complements the MAC header (26B) so that the SNAP header is DWORD
aligned without adding any pad.

Until 9000, the firmware didn't check the TX_CMD_FLG_MH_PAD bit
but rather checked the length of the MAC header itself and
assumed the entity that enqueued the frame (driver or internal
firmware code) added the pad.
Since the driver inserted the pad even for AMSDU this logic applied.
Note that the padding is a DMA optimization but it's not strictly
needed, so we could pad even if it was not needed.

However, the CSUM hardware introduced for the 9000 devices requires
to not pad AMSDU as it is not needed, and will fail if such a pad
exists.
Due to older FW not checking the padding bit but checking the mac
header size itself - we cannot do this adjustments for older
generations.
Do not align the size if it is an AMSDU and HW checksum is enabled -
which will only happen on 9000 devices and on.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This makes u-APSD work with more peers.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Bjorn pointed out that printing an error value as an
hexadecimal isn't very convenient. Change that.
Reported-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Use RX_HANDLER_ASYNC_UNLOCKED instead of unlock and re-lock
the mutex independently.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

We don't use the refcount value anymore, all the refcounting is done
in the runtime PM usage_count value.  Remove it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

When entering suspend the driver calls iwl_disable_interrupts() and
then iwl_pcie_disable_ict().
On resume the driver calls only iwl_pcie_reset_ict() without calling
explicitly to iwl_enable_interrupts().
This mostly works since iwl_pcie_reset_ict is calling to
iwl_enable_interrupts, but it doesn't work when there is no ict_table
in MSIx mode.
The result is that driver tries to resume but fails since it doesn't
get the RX interrupt from FW indicating that d0i3 exit was completed.
Fix it by adding an explicit call to enable interrupts.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

My patch resized the pool size, but neglected to resize
the global table, which is obviously wrong since the global
table maps the pool's rxb to vid one to one. This results
in a panic in 9000 devices.
Add a build bug to avoid such a case in the future.

Fixes: 7b542436 ("iwlwifi: pcie: fine tune number of rxbs")
Reported-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Add debugfs entry named lqm_send_cmd for kicking a
measurement. This hook takes the duration and the timeout
as parameter.
Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

LQM stands for Link Quality Measurement. The firmware
will collect a defined set of statitics (see the
notification for details) that allow to know how busy
the medium is. The driver issues a request to the firmware
that includes the duration of the measurement (the firmware
needs to be on channel for that amount of time) and the
timeout (in case the firmware has a lot of offchannel
activities). If the timeout elapses, the firmware will
send partial results which are still valuable.
In case of disassociation / channel switch and alike, the
driver is in charge of stopping the measurements and the
firmware will reply with partial results.

The user space API for now is debugfs only and will be
implmemented in an upcoming patch.
Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

In case of FW error, support dumping the UMAC internal txfifos.
To do so, support version 2 of shared memory cfg command, which
contains the sizes of the internal txfifos, and move the command
to the system group.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Paging contains 3 sections in the fw. The first for the paging separator,
The second for the CSS block, the third with the paging data.

Currently if the driver finds the paging separator, and there is only
section left (CSS), once reading the CSS section, the driver will
attempt to read the paging data and will go out of the arrays bounds.

Make sure that the FW image contains the right amount of sections for
paging.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Currently the driver has 2 buffers for paging:
1. paging db - this contains all of the pages that were in the FW
image, that the driver stores for the FW. This is allocated for each
block separately (not contiguous).
2. download buffer - we need to provide this empty buffer for the
iwl_sdio_load_fw_chunk function to copy the requested pages to the shared
memory. This is one big buffer of contiguous memory whose size is the
size of all the blocks that the fw paging section can contain.

This download buffer size is too big, and causes the allocation to fail
sometimes. Since the driver allocates memory for each block separately,
it is not possible for the FW to request all of the pages in one request
(the FW gives an address and size, so blocks need to be contiguous for
this to happen), therefore the FW is limited to request only one block.

Decrease the size of the paging download buffer to be the size of a
paging block.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Currently when stop flow is performed, there might be transport TX RTPM
references that are not freed in case we unmap a queue that still has
packets not reclaimed. Fix that.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Pull networking updates from David Miller:
 "Highlights:

   1) Support more Realtek wireless chips, from Jes Sorenson.

   2) New BPF types for per-cpu hash and arrap maps, from Alexei
      Starovoitov.

   3) Make several TCP sysctls per-namespace, from Nikolay Borisov.

   4) Allow the use of SO_REUSEPORT in order to do per-thread processing
   of incoming TCP/UDP connections.  The muxing can be done using a
   BPF program which hashes the incoming packet.  From Craig Gallek.

   5) Add a multiplexer for TCP streams, to provide a messaged based
      interface.  BPF programs can be used to determine the message
      boundaries.  From Tom Herbert.

   6) Add 802.1AE MACSEC support, from Sabrina Dubroca.

   7) Avoid factorial complexity when taking down an inetdev interface
      with lots of configured addresses.  We were doing things like
      traversing the entire address less for each address removed, and
      flushing the entire netfilter conntrack table for every address as
      well.

   8) Add and use SKB bulk free infrastructure, from Jesper Brouer.

   9) Allow offloading u32 classifiers to hardware, and implement for
      ixgbe, from John Fastabend.

  10) Allow configuring IRQ coalescing parameters on a per-queue basis,
      from Kan Liang.

  11) Extend ethtool so that larger link mode masks can be supported.
      From David Decotigny.

  12) Introduce devlink, which can be used to configure port link types
      (ethernet vs Infiniband, etc.), port splitting, and switch device
      level attributes as a whole.  From Jiri Pirko.

  13) Hardware offload support for flower classifiers, from Amir Vadai.

  14) Add "Local Checksum Offload".  Basically, for a tunneled packet
      the checksum of the outer header is 'constant' (because with the
      checksum field filled into the inner protocol header, the payload
      of the outer frame checksums to 'zero'), and we can take advantage
      of that in various ways.  From Edward Cree"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1548 commits)
  bonding: fix bond_get_stats()
  net: bcmgenet: fix dma api length mismatch
  net/mlx4_core: Fix backward compatibility on VFs
  phy: mdio-thunder: Fix some Kconfig typos
  lan78xx: add ndo_get_stats64
  lan78xx: handle statistics counter rollover
  RDS: TCP: Remove unused constant
  RDS: TCP: Add sysctl tunables for sndbuf/rcvbuf on rds-tcp socket
  net: smc911x: convert pxa dma to dmaengine
  team: remove duplicate set of flag IFF_MULTICAST
  bonding: remove duplicate set of flag IFF_MULTICAST
  net: fix a comment typo
  ethernet: micrel: fix some error codes
  ip_tunnels, bpf: define IP_TUNNEL_OPTS_MAX and use it
  bpf, dst: add and use dst_tclassid helper
  bpf: make skb->tc_classid also readable
  net: mvneta: bm: clarify dependencies
  cls_bpf: reset class and reuse major in da
  ldmvsw: Checkpatch sunvnet.c and sunvnet_common.c
  ldmvsw: Add ldmvsw.c driver code
  ...

Pull cgroup updates from Tejun Heo:
 "cgroup changes for v4.6-rc1.  No userland visible behavior changes in
  this pull request.  I'll send out a separate pull request for the
  addition of cgroup namespace support.

   - The biggest change is the revamping of cgroup core task migration
     and controller handling logic.  There are quite a few places where
     controllers and tasks are manipulated.  Previously, many of those
     places implemented custom operations for each specific use case
     assuming specific starting conditions.  While this worked, it makes
     the code fragile and difficult to follow.

     The bulk of this pull request restructures these operations so that
     most related operations are performed through common helpers which
     implement recursive (subtrees are always processed consistently)
     and idempotent (they make cgroup hierarchy converge to the target
     state rather than performing operations assuming specific starting
     conditions).  This makes the code a lot easier to understand,
     verify and extend.

   - Implicit controller support is added.  This is primarily for using
     perf_event on the v2 hierarchy so that perf can match cgroup v2
     path without requiring the user to do anything special.  The kernel
     portion of perf_event changes is acked but userland changes are
     still pending review.

   - cgroup_no_v1= boot parameter added to ease testing cgroup v2 in
     certain environments.

   - There is a regression introduced during v4.4 devel cycle where
     attempts to migrate zombie tasks can mess up internal object
     management.  This was fixed earlier this week and included in this
     pull request w/ stable cc'd.

   - Misc non-critical fixes and improvements"

* 'for-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: (44 commits)
  cgroup: avoid false positive gcc-6 warning
  cgroup: ignore css_sets associated with dead cgroups during migration
  Documentation: cgroup v2: Trivial heading correction.
  cgroup: implement cgroup_subsys->implicit_on_dfl
  cgroup: use css_set->mg_dst_cgrp for the migration target cgroup
  cgroup: make cgroup[_taskset]_migrate() take cgroup_root instead of cgroup
  cgroup: move migration destination verification out of cgroup_migrate_prepare_dst()
  cgroup: fix incorrect destination cgroup in cgroup_update_dfl_csses()
  cgroup: Trivial correction to reflect controller.
  cgroup: remove stale item in cgroup-v1 document INDEX file.
  cgroup: update css iteration in cgroup_update_dfl_csses()
  cgroup: allocate 2x cgrp_cset_links when setting up a new root
  cgroup: make cgroup_calc_subtree_ss_mask() take @this_ss_mask
  cgroup: reimplement rebind_subsystems() using cgroup_apply_control() and friends
  cgroup: use cgroup_apply_enable_control() in cgroup creation path
  cgroup: combine cgroup_mutex locking and offline css draining
  cgroup: factor out cgroup_{apply|finalize}_control() from cgroup_subtree_control_write()
  cgroup: introduce cgroup_{save|propagate|restore}_control()
  cgroup: make cgroup_drain_offline() and cgroup_apply_control_{disable|enable}() recursive
  cgroup: factor out cgroup_apply_control_enable() from cgroup_subtree_control_write()
  ...

bond_get_stats() can be called from rtnetlink (with RTNL held)
or from /proc/net/dev seq handler (with RCU held)

The logic added in commit 5f0c5f73 ("bonding: make global bonding
stats more reliable") kind of assumed only one cpu could run there.

If multiple threads are reading /proc/net/dev, stats can be really
messed up after a while.

A second problem is that some fields are 32bit, so we need to properly
handle the wrap around problem.

Given that RTNL is not always held, we need to use
bond_for_each_slave_rcu().

Fixes: 5f0c5f73 ("bonding: make global bonding stats more reliable")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Andy Gospodarek <gospo@cumulusnetworks.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When un-mapping skb->data in __bcmgenet_tx_reclaim(),
we must use the length that was used in original dma_map_single(),
instead of skb->len that might be bigger (includes the frags)

We simply can store skb_len into tx_cb_ptr->dma_len and use it
at unmap time.

Fixes: 1c1008c7 ("net: bcmgenet: add main driver file")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 85743f1e ("net/mlx4_core: Set UAR page size to 4KB regardless
of system page size") introduced dependency where old VF drivers without
this fix fail to load if the PF driver runs with this commit.

To resolve this add a module parameter which disables that functionality
by default.  If both the PF and VFs are running with a driver with that
commit the administrator may set the module param to true.

The module parameter is called enable_4k_uar.

Fixes: 85743f1e ('net/mlx4_core: Set UAR page size to 4KB ...')
Signed-off-by: Eli Cohen <eli@mellanox.com>
Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull libata updates from Tejun Heo:

 - ahci grew runtime power management support so that the controller can
   be turned off if no devices are attached.

 - sata_via isn't dead yet.  It got hotplug support and more refined
   workaround for certain WD drives.

 - Misc cleanups.  There's a merge from for-4.5-fixes to avoid confusing
   conflicts in ahci PCI ID table.

* 'for-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  ata: ahci_xgene: dereferencing uninitialized pointer in probe
  AHCI: Remove obsolete Intel Lewisburg SATA RAID device IDs
  ata: sata_rcar: Use ARCH_RENESAS
  sata_via: Implement hotplug for VT6421
  sata_via: Apply WD workaround only when needed on VT6421
  ahci: Add runtime PM support for the host controller
  ahci: Add functions to manage runtime PM of AHCI ports
  ahci: Convert driver to use modern PM hooks
  ahci: Cache host controller version
  scsi: Drop runtime PM usage count after host is added
  scsi: Set request queue runtime PM status back to active on resume
  block: Add blk_set_runtime_active()
  ata: ahci_mvebu: add support for Armada 3700 variant
  libata: fix unbalanced spin_lock_irqsave/spin_unlock_irq() in ata_scsi_park_show()
  libata: support AHCI on OCTEON platform

Pull workqueue updates from Tejun Heo:
 "Three trivial workqueue changes"

* 'for-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
  workqueue: Fix comment for work_on_cpu()
  sched/core: Get rid of 'cpu' argument in wq_worker_sleeping()
  workqueue: Replace usage of init_name with dev_set_name()

Drop two extra occurrences of "on" in option title and help text.

Fixes: 379d7ac7 ("phy: mdio-thunder: Add driver for Cavium Thunder SoC MDIO buses.")
Cc: David Daney <david.daney@cavium.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add lan78xx_get_stats64 of ndo_get_stats64 to report
all statistics counters including errors from HW statistics.

Read from HW when auto suspend is disabled, use saved counter when
auto suspend is enabled because periodic call to ndo_get_stats64
prevents USB auto suspend.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update to handle statistics counter rollover.
Check statistics counter periodically and compensate it when
counter value rolls over at max (20 or 32bits).

Simple mechanism adjusts monitoring timer to allow USB auto suspend.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>