- 08 Nov, 2011 20 commits
-
-
Arend van Spriel authored
The data from the sprom consists of u16 values stored in little endian notation over which a crc8 was determined. To validate this the buffer needed to be converted for big-endian systems. Reading the sprom data is now done per byte so conversion is only done after a successful crc8 check. Reviewed-by:
Alwin Beukers <alwin@broadcom.com> Reviewed-by:
Roland Vossen <rvossen@broadcom.com> Signed-off-by:
Arend van Spriel <arend@broadcom.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Arend van Spriel authored
The n-phy requested some srom variables that are no longer needed and consequently not present in the srom revision 8 and higher that this driver support. This code has been removed from the n-phy. Reviewed-by:
-
Roland Vossen authored
In case the hardware crashes, a reinitialization internal to the driver was performed. Since Mac80211 must be in the know of such an event as well, ieee80211_restart_hw() is now called. Reviewed-by:
-
Roland Vossen authored
struct brcmf_scan_results contained a 1 element array, but in reality the number of scan results can be 0 or more, as indicated by the count field in the same struct. Array has be redefined to be 0 elements length to indicate the array is purely for reference. Reported-by:
Johannes Berg <johannes@sipsolutions.net> Reviewed-by:
Franky (Zhenhui) Lin <frankyl@broadcom.com> Signed-off-by:
-
Roland Vossen authored
Moved function to where it is called and made it more readable. Reviewed-by:
-
Roland Vossen authored
Made code more readable. Reviewed-by:
-
Roland Vossen authored
Supported chips contain SROM rev 8 and upwards. Reported-by:
Hauke Mehrtens <hauke@hauke-m.de> Reviewed-by:
-
Arend van Spriel authored
The brcmsmac driver registered with mac80211 with HT capability info set to 40MHz intolerant. This cause any other station on the channel to be forced to use 20MHz. This flag has been removed. Reported-by:
-
Alwin Beukers authored
Removed defines from aiutils.h also present in soc.h. Reported-by:
-
Alwin Beukers authored
Signed-off-by:
-
Johannes Berg authored
There's an extra pair of parentheses here that is simply confusing because it implies a nesting that doesn't actually exist. Just remove it. Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Dan Carpenter authored
My previous patch added a check to get_key() but missed a couple other places which need range checks. The problem here is that wifi drivers have different numbers of keys. The lower levels assume that they can have up to 4 default keys and 2 management keys but this driver only has the default keys so we could go past the end of the ->keys[] array. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Acked-by:
Samuel Ortiz <sameo@linux.intel.com> Signed-off-by:
-
Dan Carpenter authored
Wifi drivers can have up to 6 keys but the rndis_wlan only has 4 so it needs to have its own checks to make sure we don't go out of bounds. The add_key() function already checks but I added some checks to del_key() and set_default_key(). Signed-off-by:
Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by:
-
Dan Carpenter authored
The code here treats very large values of "limit" as less than MAX_POWER_RATE because of the cast to int. We should do the compare as u32 instead. Signed-off-by:
Pavel Roskin <proski@gnu.org> Signed-off-by:
-
Eliad Peller authored
mac80211 calls ieee80211_set_wmm_default (which in turn calls drv_conf_tx()) for every new interface, including "internal" ones (e.g. monitor interface, which the low-level driver doesn't know about). Limit this call only to valid interfaces. Reported-by:
Eliad Peller <eliad@wizery.com> Signed-off-by:
-
Johannes Berg authored
When userspace requested that a scan not be done with CCK rates, use 6 Mbps. This is used for example for P2P scanning. Signed-off-by:
Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by:
-
Don Fry authored
The iwl_alloc_all routine is only called once. Delete the argument and print an error in the calling routine if needed. Signed-off-by:
Don Fry <donald.h.fry@intel.com> Signed-off-by:
-
Wey-Yi Guy authored
Set the HW rev. for both 105 and 135 series Signed-off-by:
-
Don Fry authored
The device tracing routines only use the priv pointer as an opaque value. Change from a typed iwl_priv pointer to a null pointer and eliminate the need to include iwl_priv.h. CMD_ASYNC is defined in iwl_shared.h which is the only reason it is included. Signed-off-by:
-
Johannes Berg authored
The WoWLAN API changed due to netdetect and we now have a more generic "D3 configuration" command that enables the sysassert & rfkill wakeup triggers. Signed-off-by:
-
- 24 Oct, 2011 20 commits
-
-
Richard Cochran authored
If the PHY should disappear (for example, on an USB Ethernet MAC), then the driver would leak any undelivered time stamp packets. This commit fixes the issue by calling the appropriate functions to free any packets left in the transmit and receive queues. The driver first appeared in v3.0. Signed-off-by:
Richard Cochran <richard.cochran@omicron.at> Acked-by:
Eric Dumazet <eric.dumazet@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Richard Cochran authored
The previous commit enforces a new rule for handling the cloned packets for transmit time stamping. These packets must not be freed using any other function than skb_complete_tx_timestamp. This commit fixes the one and only driver using this API. The driver first appeared in v3.0. Signed-off-by:
-
Andreas Hofmeister authored
When hybrid mode is enabled (accept_ra == 2), the kernel also sees RAs generated locally. This is useful since it allows the kernel to auto-configure its own interface addresses. However, if 'accept_ra_defrtr' and/or 'accept_ra_rtr_pref' are set and the locally generated RAs announce the default route and/or other route information, the kernel happily inserts bogus routes with its own address as gateway. With this patch, adding routes from an RA will be skiped when the RAs source address matches any local address, just as if 'accept_ra_defrtr' and 'accept_ra_rtr_pref' were set to 0. Signed-off-by:
Andreas Hofmeister <andi@collax.com> Signed-off-by:
-
Eric Dumazet authored
If a frame cant be transmitted, it is silently discarded. Add a counter to report these errors to user. Signed-off-by:
-
Sathya Perla authored
When the HW is in multi-channel mode based on the skew/IPL, there are 4 functions per port and so not enough resources to create multiple RX/TX rings for each function. Signed-off-by:
Suresh Reddy <suresh.reddy@emulex.com> Signed-off-by:
Sathya Perla <sathya.perla@emulex.com> Signed-off-by:
-
Sathya Perla authored
Multiple TXQ support is partially broken in BE2. It is fully supported BE3 onwards and in Lancer. Signed-off-by:
Vasundhara Volam <vasundhara.volam@emulex.com> Signed-off-by:
-
Sathya Perla authored
Currently the code for VF setup/teardown done by a PF (if_create, mac_add_config, link_status_query etc) is scattered; this patch refactors this code into be_vf_setup() and be_vf_clear(). The if_create/if_destroy/mac_addr_query cmds are now called after the MCCQ is created; so these cmds are now modified to use the MCCQ instead of MBOX. Signed-off-by:
-
Sathya Perla authored
When a card is reset due to EEH error recovery or due to a suspend, rx-mode config (promisc/mc) is not being sent to the FW. be_setup() is called in these flows and is the best place for such config/re-config cmds. Hence include rx-mode, vlan and flow-control config in be_setup(). Signed-off-by:
-
Eric Dumazet authored
Dan Siemon would like to add tunnelling support to cls_flow This preliminary patch introduces use of skb_header_pointer() to help this task, while avoiding skb head reallocation because of deep packet inspection. Signed-off-by:
-
Gao feng authored
In func ipv4_dst_check,check_peer_pmtu should be called only when peer is updated. So,if the peer is not updated in ip_rt_frag_needed,we can not inc __rt_peer_genid. Signed-off-by:
Gao feng <gaofeng@cn.fujitsu.com> Acked-by:
-
David S. Miller authored
-
Flavio Leitner authored
It was enabled by default and the messages guarded by the define are useful. Signed-off-by:
Flavio Leitner <fbl@redhat.com> Signed-off-by:
-
Dirk Eibach authored
Since commit "74888760... dt/net: Eliminate users of of_platform_{,un}register_driver" there are two platform drivers named "mdio-gpio" registered. I renamed the of variant to "mdio-ofgpio". Signed-off-by:
Dirk Eibach <eibach@gdsys.de> Signed-off-by:
-
-
Eric Dumazet authored
There is a long standing bug in linux tcp stack, about ACK messages sent on behalf of TIME_WAIT sockets. In the IP header of the ACK message, we choose to reflect TOS field of incoming message, and this might break some setups. Example of things that were broken : - Routing using TOS as a selector - Firewalls - Trafic classification / shaping We now remember in timewait structure the inet tos field and use it in ACK generation, and route lookup. Notes : - We still reflect incoming TOS in RST messages. - We could extend MuraliRaja Muniraju patch to report TOS value in netlink messages for TIME_WAIT sockets. - A patch is needed for IPv6 Signed-off-by:
-
Eric W. Biederman authored
Renato Westphal noticed that since commit a2835763 "rtnetlink: handle rtnl_link netlink notifications manually" was merged we no longer send a netlink message when a networking device is moved from one network namespace to another. Fix this by adding the missing manual notification in dev_change_net_namespaces. Since all network devices that are processed by dev_change_net_namspaces are in the initialized state the complicated tests that guard the manual rtmsg_ifinfo calls in rollback_registered and register_netdevice are unnecessary and we can just perform a plain notification. Cc: stable@kernel.org Tested-by:
Renato Westphal <renatowestphal@gmail.com> Signed-off-by:
Eric W. Biederman <ebiederm@xmission.com> Signed-off-by:
-
Yan, Zheng authored
There is bug in commit 5e2b61f7(ipv4: Remove flowi from struct rtable). It makes xfrm4_fill_dst() modify wrong data structure. Signed-off-by:
Zheng Yan <zheng.z.yan@intel.com> Reported-by:
Kim Phillips <kim.phillips@freescale.com> Acked-by:
-
Clemens Buchacher authored
If the device is down during suspend/resume, interrupts are enabled without a registered interrupt handler, causing a storm of unhandled interrupts until the IRQ is disabled because "nobody cared". Instead, check that the device is up before touching it in the suspend/resume code. Fixes https://bugzilla.kernel.org/show_bug.cgi?id=39112Helped-by:
Adrian Chadd <adrian@freebsd.org> Helped-by:
Mohammed Shafi <shafi.wireless@gmail.com> Signed-off-by:
Clemens Buchacher <drizzd@aon.at> Signed-off-by:
-
Flavio Leitner authored
The commit f39925db (ipv4: Cache learned redirect information in inetpeer.) removed some ICMP packet validations which are required by RFC 1122, section 3.2.2.2: ... A Redirect message SHOULD be silently discarded if the new gateway address it specifies is not on the same connected (sub-) net through which the Redirect arrived [INTRO:2, Appendix A], or if the source of the Redirect is not the current first-hop gateway for the specified destination (see Section 3.3.1). Signed-off-by:
-
Richard Cochran authored
The pair of functions, * skb_clone_tx_timestamp() * skb_complete_tx_timestamp() were designed to allow timestamping in PHY devices. The first function, called during the MAC driver's hard_xmit method, identifies PTP protocol packets, clones them, and gives them to the PHY device driver. The PHY driver may hold onto the packet and deliver it at a later time using the second function, which adds the packet to the socket's error queue. As pointed out by Johannes, nothing prevents the socket from disappearing while the cloned packet is sitting in the PHY driver awaiting a timestamp. This patch fixes the issue by taking a reference on the socket for each such packet. In addition, the comments regarding the usage of these function are expanded to highlight the rule that PHY drivers must use skb_complete_tx_timestamp() to release the packet, in order to release the socket reference, too. These functions first appeared in v2.6.36. Reported-by:
-
