Define ixAZALIA_F0_CODEC_PIN_CONTROL_ACP_DATA
Define AZALIA_F0_CODEC_PIN_CONTROL_ACP_DATA__SUPPORTS_AI_MASK/SHIFT
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Protect remove_hpo_dp_link_enc_from_ctx() and release_hpo_dp_link_enc()
with CONFIG_DRM_AMD_DC_DCN as the functions are only called from code
that is protected by CONFIG_DRM_AMD_DC_DCN.  Fixes build fail with
-Werror=unused-function.

Fixes: 9b0e0d433f74 ("drm/amd/display: Add dependant changes for DCN32/321")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>

Revised validation logic when marking for seamless boot. Init resources
accordingly when Pre-OS has ODM enabled. Reset ODM when transitioning
Pre-OS odm to Post-OS non-odm to avoid corruption. Apply logic to set
odm accordingly upon commit.
Signed-off-by: Duncan Ma <duncan.ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[WHY & HOW]
Implements DTB ref clock switching with reg key default to OFF.
Refactors dccg DTBCLK logic to not store redundant state information
dccg. Also removes duplicated functions that should be inherited from
other dcn versions.
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Update base.dprefclk_khz to match result from dcn32_dump_clk_registers()
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This commit cleans up code that uses old variables and adds some SMU
interfaces for future flexibility.
Signed-off-by: Martin Leung <Martin.Leung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Use DTBCLK for valid pixel clock generation
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Previously we used to send FCLK P-state enable messages upon each call
to update_clocks based on dml output. This resulted in increased message
transactions between DC and PMFW.

[How]
Update the code to check safe_to_lower status and send the message based
on dml input only on boot. This reduces message transactions. Also
remove other unwanted code based on current code status.
Signed-off-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
DCN has sidebands to control some clocks, it is useful for clk_mgr to
always update the clocks it explicitly controls rather than skip them
because it enables more configurations to work without SMU

[how]
only skip handling clocks where SMU manages the frequency for clocks
with DENTIST sideband (DISP/DPP), only skip the voltage request when SMU
not available, but otherwise proceed normally
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

We can now enable FEC.
Signed-off-by: Jingwen Zhu <Jingwen.Zhu@github.amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
New dividers in DCCG need to be programmed depending
on encoder/stream type since pixels per clock in
OTG/DIO is different

DIO also needs additional programming depending on
pixels per clock
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>

[Description]
By default we can now set
ODM_MEM_VBLANK_PWR_MODE=1
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

LVDS support was implemented in DC a while ago.  Just DAC
support is left to do.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
HUBP_UNBOUNDED_REQ_MODE and CURSOR_REQ_MODE are normally set together.
In hubp32_prepare_subvp_buffering() call, CURSOR_REQ_MODE is set based on
whether SubVP is enabled or not.  For non MPO case, both REQ_MODE
registers are set to 1.  But since SubVP is not enabled, then
CURSOR_REQ_MODE is set to 0, overriding the previous value.

[How]
Do not set CURSOR_REQ_MODE to 0 if SubVP is not enabled.  This
will allow CURSOR_REQ_MODE to stay as 1 in the non MPO case.
Add note to follow up and check case for single pipe MPO and
SubVP enabled as this would cause both REQ_MODE registers to be
set to 0 but SubVP enabled would override CURSOR_REQ_MODE to 1.
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

We know that "grbm_soft_reset" is true because we're already inside an
if (grbm_soft_reset) condition.  No need to test again.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Use the per asic offsets so the we don't have to have
asic specific logic in the common code.
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com>
Reviewed-by: Yang Wang <kevinyang.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Set appropriate caps for DCN3.2.x.
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

So we can eventaully use them in the common smu code for
accessing the SMU mailboxes without needing a lot of
per asic logic in the common code.
Reviewed-by: Yang Wang <kevinyang.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[How & Why]
To be enabled once PMFW supports it.
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Enable the AGP aperture on chips with GMC v11.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Check IP version rather than asic type.
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[WHY?]
If higher states have memory speed set to 0 MT/s currently they do not get set
to the highest value which can cause validation failures.

[HOW?]
Set unpopulated higher states to max value.
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Drop all of the extra cases in the default case.
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Rather than asic type.
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

VBIOS default clock value was halved, so the hardcoded dtb value should be
halved as well.

dtb clock should come from SMU eventually, but now dtb clock switching is not
fully supported yet in SMU.

Halve the dtb hardcoded value for now to have UHBR10 light up. Will rely on
SMU for dtb clock switching once available. The w/a is for DCN32 only, DCN321
should adopt the original value.
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This patch will fix sdma doorbell issue on SDMA v6.0 and NBIO v7.7.0.
NBIO v7.7.0 uses a new reg function -- Common SDMA to allow a common
doorbell range for all SDMA queues, this is different to the old
NBIO version. This patch will add configuration for CSDMA and enable
SDMA doorbell function.
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: Tim Huang <Tim.Huang@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This patch will add CSDMA reg offsets for NBIO v7.7.0
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

APU required to issue the enable GFX IMU message after IMU reset.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Tim Huang <Tim.Huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

GC v11_0_1 asic needs to issue the EnableGfxImu message after start IMU.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Tim Huang <Tim.Huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Update MP v13_0_4 register macro for SMU message

v2: squash in missed case (Alex)
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Tim Huang <Tim.Huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This adds mmhub v3_0_1 ip block support

v2: rebase (Alex)
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Tim Huang <Tim.Huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add mmhub v3_0_1 headers, because there are many differeces with v3_0_0.

v2: squash in updates (Alex)
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Tim Huang <Tim.Huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Switch to use the callback function to poll the reset status on IMU.
Because it will have different sequency on other ASICs.

v2: drop unused variable (Alex)
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why?]
On wake from S3/S4, driver checks if DMUB is initialized. On S4 VBIOS loads
DMUB, and driver does not reload as it appears to be initialized already.

[How?]
Add a check for the DAL_FW bit to ensure that loaded FW is from driver and
not VBIOS.
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
Use correct clock source initialization routine for DCN32/321
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[WHY&HOW]
Change criteria for setting DTO source value, and always set it regardless of
the signal type.
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com>
Acked-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Disable idle optimizations until SMU can handle them to prevent DMUB
timeout and subsequent system freeze
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>