This is a hold over from before the struct device conversion.

- All prints should be using &chip->dev, which is the Linux
  standard. This changes prints to use tpm0 as the device name,
  not the PnP/etc ID.
- The few places involving sysfs/modules that really do need the
  parent just use chip->dev.parent instead
- We no longer need to get_device(pdev) in any places since it is no
  longer used by any of the code. The kref on the parent is held
  by the device core during device_add and dropped in device_del
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Simplify st33zp24_spi_acpi_request_resources, st33zp24_spi_of_request_resources
and st33zp24_spi_request_resources to have the same prototype and using
spi_get_drvdata.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Simplify st33zp24_i2c_acpi_request_resources, st33zp24_i2c_of_request_resources
and st33zp24_i2c_request_resources to have the same prototype and using
i2c_get_clientdata.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Add support for acpi probing. SMO3324 is used for st33zp24.
It has been tested with the following acpi node on Minnowboard:

Device (TPM1)
{
	Name (_ADR, Zero)  // _ADR: Address
	Name (_HID, "SMO3324")  // _HID: Hardware ID
	Name (_CID, "SMO3324")  // _CID: Compatible ID
	Name (_DDN, "SMO TPM")  // _DDN: DOS Device Name
	Name (_UID, One)  // _UID: Unique ID
	Method (_CRS, 0, NotSerialized)  // _CRS: Current Resource Settings
	{
		Name (SBUF, ResourceTemplate ()
		{
			SpiSerialBus (0, PolarityLow, FourWireMode, 8,
				      ControllerInitiated, 4000000, ClockPolarityLow,
				      ClockPhaseFirst, "\\_SB.SPI1",
				      0x00, ResourceConsumer, ,)
			GpioInt (Edge, ActiveHigh, ExclusiveAndWake, PullNone, 0x0000,
				 "\\_SB.GPO2", 0x00, ResourceConsumer, ,)
			{       // Pin list
				0x0001
			}
			GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly,
				"\\_SB.GPO2", 0x00, ResourceConsumer, ,)
			{       // Pin list
				0x0002,
			}
		})
		Return (SBUF) /* \_SB_.SPI1.TPM1._CRS.SBUF */
	}
	Method (_STA, 0, NotSerialized)  // _STA: Status
	{
		Return (0x0F)
	}
}
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Add support for acpi probing. SMO3324 is used for st33zp24.
It has been tested with the following acpi node on Minnowboard:

Device (TPM1)
{
	Name (_ADR, Zero)  // _ADR: Address
	Name (_HID, "SMO3324")  // _HID: Hardware ID
	Name (_CID, "SMO3324")  // _CID: Compatible ID
	Name (_DDN, "SMO TPM")  // _DDN: DOS Device Name
	Name (_UID, One)  // _UID: Unique ID
	Method (_CRS, 0, NotSerialized)  // _CRS: Current Resource Settings
	{
		Name (SBUF, ResourceTemplate ()
		{
			I2cSerialBus (0x0013, ControllerInitiated, 400000,
				      AddressingMode7Bit, "\\_SB.I2C7",
				      0x00, ResourceConsumer, ,)
			GpioInt (Edge, ActiveHigh, ExclusiveAndWake, PullNone, 0x0000,
				 "\\_SB.GPO2", 0x00, ResourceConsumer, ,)
			{   	// Pin list
				0x0001
			}
			GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly,
				"\\_SB.GPO2", 0x00, ResourceConsumer, ,)
			{	// Pin list
				0x0002,
			}
		})
		Return (SBUF) /* \_SB_.I2C7.TPM1._CRS.SBUF */
	}

	Method (_STA, 0, NotSerialized)  // _STA: Status
	{
		Return (0x0F)
	}
}
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Extend copyright header to 2016
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Add check in st33zp24_spi_evaluate_latency helping to diagnose if the chip
is present or in a bad state.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

DT headers already define NOOP routines when CONFIG_OF is not defined.

[jarkko.sakkinen@linux.intel.com: I tested that the driver compiles
 without warnings and errors with and without CONFIG_OF flag.]
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Remove spi_xfer from st33zp24_spi_phy structure and declare local spi_xfer
when needed instead.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

An affectation is enough when copying 1 byte. Remove memcpy usage where
possible.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Make sure every function name use st33zp24_spi_ prefix.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

nbr_dummy_bytes variable could be easily replaced by phy->latency in
st33zp24_spi_send and st33zp24_spi_recv.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Simplify st33zp24_spi_acpi_request_resources, st33zp24_spi_of_request_resources
and st33zp24_spi_request_resources to have the same prototype and using
spi_get_drvdata.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Simplify st33zp24_i2c_acpi_request_resources, st33zp24_i2c_of_request_resources
and st33zp24_i2c_request_resources to have the same prototype and using
i2c_get_clientdata.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Add support for acpi probing. SMO3324 is used for st33zp24.
It has been tested with the following acpi node on Minnowboard:

Device (TPM1)
{
	Name (_ADR, Zero)  // _ADR: Address
	Name (_HID, "SMO3324")  // _HID: Hardware ID
	Name (_CID, "SMO3324")  // _CID: Compatible ID
	Name (_DDN, "SMO TPM")  // _DDN: DOS Device Name
	Name (_UID, One)  // _UID: Unique ID
	Method (_CRS, 0, NotSerialized)  // _CRS: Current Resource Settings
	{
		Name (SBUF, ResourceTemplate ()
		{
			SpiSerialBus (0, PolarityLow, FourWireMode, 8,
				      ControllerInitiated, 4000000, ClockPolarityLow,
				      ClockPhaseFirst, "\\_SB.SPI1",
				      0x00, ResourceConsumer, ,)
			GpioInt (Edge, ActiveHigh, ExclusiveAndWake, PullNone, 0x0000,
				 "\\_SB.GPO2", 0x00, ResourceConsumer, ,)
			{       // Pin list
				0x0001
			}
			GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly,
				"\\_SB.GPO2", 0x00, ResourceConsumer, ,)
			{       // Pin list
				0x0002,
			}
		})
		Return (SBUF) /* \_SB_.SPI1.TPM1._CRS.SBUF */
	}
	Method (_STA, 0, NotSerialized)  // _STA: Status
	{
		Return (0x0F)
	}
}
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Add support for acpi probing. SMO3324 is used for st33zp24.
It has been tested with the following acpi node on Minnowboard:

Device (TPM1)
{
	Name (_ADR, Zero)  // _ADR: Address
	Name (_HID, "SMO3324")  // _HID: Hardware ID
	Name (_CID, "SMO3324")  // _CID: Compatible ID
	Name (_DDN, "SMO TPM")  // _DDN: DOS Device Name
	Name (_UID, One)  // _UID: Unique ID
	Method (_CRS, 0, NotSerialized)  // _CRS: Current Resource Settings
	{
		Name (SBUF, ResourceTemplate ()
		{
			I2cSerialBus (0x0013, ControllerInitiated, 400000,
				      AddressingMode7Bit, "\\_SB.I2C7",
				      0x00, ResourceConsumer, ,)
			GpioInt (Edge, ActiveHigh, ExclusiveAndWake, PullNone, 0x0000,
				 "\\_SB.GPO2", 0x00, ResourceConsumer, ,)
			{   	// Pin list
				0x0001
			}
			GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly,
				"\\_SB.GPO2", 0x00, ResourceConsumer, ,)
			{	// Pin list
				0x0002,
			}
		})
		Return (SBUF) /* \_SB_.I2C7.TPM1._CRS.SBUF */
	}

	Method (_STA, 0, NotSerialized)  // _STA: Status
	{
		Return (0x0F)
	}
}
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Extend copyright header to 2016
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Add check in st33zp24_spi_evaluate_latency helping to diagnose if the chip
is present or in a bad state.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

The core st33zp24 module is useless without either the I2C or the
SPI access module. So hide NFC_ST_NCI and select it automatically
if either TCG_TIS_ST33ZP24_I2C or TCG_TIS_ST33ZP24_SPI is selected.

This avoids presenting TCG_TIS_ST33ZP24 when neither TCG_TIS_ST33ZP24_I2C
nor TCG_TIS_ST33ZP24_SPI can be selected.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

DT headers already define NOOP routines when CONFIG_OF is not defined.

[jarkko.sakkinen@linux.intel.com: I tested that the driver compiles
 without warnings and errors with and without CONFIG_OF flag.]
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Remove spi_xfer from st33zp24_spi_phy structure and declare local spi_xfer
when needed instead.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

An affectation is enough when copying 1 byte. Remove memcpy usage where
possible.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Make sure every function name use st33zp24_spi_ prefix.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

nbr_dummy_bytes variable could be easily replaced by phy->latency in
st33zp24_spi_send and st33zp24_spi_recv.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Close the hole where ptrace can change a syscall out from under seccomp.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: user-mode-linux-devel@lists.sourceforge.net

Close the hole where ptrace can change a syscall out from under seccomp.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Chris Metcalf <cmetcalf@mellanox.com>

Close the hole where ptrace can change a syscall out from under seccomp.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org

Close the hole where ptrace can change a syscall out from under seccomp.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: linux-s390@vger.kernel.org

Close the hole where ptrace can change a syscall out from under seccomp.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: linux-parisc@vger.kernel.org

Close the hole where ptrace can change a syscall out from under seccomp.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: "Maciej W. Rozycki" <macro@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org

Close the hole where ptrace can change a syscall out from under seccomp.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org

Close the hole where ptrace can change a syscall out from under seccomp.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org

This moves seccomp after ptrace on x86 to that seccomp can catch changes
made by ptrace. Emulation should skip the rest of processing too.

We can get rid of test_thread_flag because there's no longer any
opportunity for seccomp to mess with ptrace state before invoking
ptrace.
Suggested-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: x86@kernel.org
Cc: Andy Lutomirski <luto@kernel.org>

When RET_TRACE triggers, a tracer may change a syscall into something that
should be filtered by seccomp. This re-runs seccomp after a trace event
to make sure things continue to pass.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Andy Lutomirski <luto@kernel.org>

Since nothing is using the 2-phase API, and it adds more complexity than
benefit, remove it.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Andy Lutomirski <luto@kernel.org>

I added two-phase syscall entry work back when the entry slow path
was very slow.  Nowadays, the entry slow path is fast and two-phase
entry work serves no purpose.  Remove it.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>

Currently, if arch code wants to supply seccomp_data directly to
seccomp (which is generally much faster than having seccomp do it
using the syscall_get_xyz() API), it has to use the two-phase
seccomp hooks. Add it to the easy hooks, too.

Cc: linux-arch@vger.kernel.org
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>

One problem with seccomp was that ptrace could be used to change a
syscall after seccomp filtering had completed. This was a well documented
limitation, and it was recommended to block ptrace when defining a filter
to avoid this problem. This can be quite a limitation for containers or
other places where ptrace is desired even under seccomp filters.

This adds tests for both SECCOMP_RET_TRACE and PTRACE_SYSCALL manipulations.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Andy Lutomirski <luto@kernel.org>

The code is doing the equivalent of the kthread_run macro.
Signed-off-by: Mike Danese <mikedanese@google.com>
Acked-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: James Morris <james.l.morris@oracle.com>

The capability check should not be audited since it is only being used
to determine the inode permissions. A failed check does not indicate a
violation of security policy but, when an LSM is enabled, a denial audit
message was being generated.

The denial audit message caused confusion for some application authors
because root-running Go applications always triggered the denial. To
prevent this confusion, the capability check in net_ctl_permissions() is
switched to the noaudit variant.

BugLink: https://launchpad.net/bugs/1465724Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Acked-by: Serge E. Hallyn <serge.hallyn@ubuntu.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>