- 16 Jul, 2020 4 commits
-
-
Geert Uytterhoeven authored
Make the Makefile for building Renesas DTB files easier to read and maintain: - Get rid of line continuations, - Use a single entry per line, - Sort SoCs and boards alphabetically, - Separate SoCs by blank lines. Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by:
Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Link: https://lore.kernel.org/r/20200706154015.29257-1-geert+renesas@glider.be
-
Geert Uytterhoeven authored
The PHY mode already defaults to RGMII in the RZ/G2E base SoC DTS file, so there is no need to specify the same value in board files. Fixes: 6b170cd3 ("arm64: dts: renesas: cat875: Add ethernet support") Signed-off-by:
Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Link: https://lore.kernel.org/r/20200706151400.23105-1-geert+renesas@glider.be
-
Niklas Söderlund authored
The remote property is never read by the driver, remove it. Signed-off-by:
-
Niklas Söderlund authored
When adding the adv7180 device node the ports node was misspelled as port, fix this. Fixes: 8cae3590 ("ARM: dts: gose: add composite video input") Signed-off-by:
-
- 13 Jul, 2020 4 commits
-
-
Sergei Shtylyov authored
Define the Eagle/V3MSK board dependent parts of the RPC-IF device node. Add device nodes for Spansion S25FS512S SPI flash and MTD partitions on it. Based on the original patches by Dmitry Shifrin. Signed-off-by:
Dmitry Shifrin <dmitry.shifrin@cogentembedded.com> Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Link: https://lore.kernel.org/r/fca1d012-29bf-eead-1c0d-4dd837c0bc68@cogentembedded.comSigned-off-by:
-
Sergei Shtylyov authored
Describe RPC-IF in the R8A77970 device tree. Signed-off-by:
-
Sergei Shtylyov authored
Define the Condor/V3HSK board dependent parts of the RPC-IF device node. Add device nodes for Spansion S25FS512S SPI flash and MTD partitions on it. Based on the original patches by Dmitry Shifrin. Signed-off-by:
-
Sergei Shtylyov authored
Describe RPC-IF in the R8A77980 device tree. Signed-off-by:
-
- 29 Jun, 2020 1 commit
-
-
Ulrich Hecht authored
Make use of the IRLM setup feature in the renesas-intc-irqpin driver. Signed-off-by:
Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Tested-by:
Simon Horman <horms+renesas@verge.net.au> Link: https://lore.kernel.org/r/1441726946-30131-3-git-send-email-ulrich.hecht+renesas@gmail.comSigned-off-by:
-
- 26 Jun, 2020 13 commits
-
-
Lad Prabhakar authored
The HiHope RZ/G2N variants are advertised as compatible with panel idk-1110wr from Advantech, however the panel isn't sold alongside the board. New dts's, enabling the lvds node to get the panel to work with all the HiHope RZ/G2N variants. Signed-off-by:
Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com> Link: https://lore.kernel.org/r/1593004330-5039-12-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.comSigned-off-by:
-
Lad Prabhakar authored
The HiHope RZ/G2N sub board sits below the HiHope RZ/G2N Rev.3.0/4.0 main board. Signed-off-by:
-
Lad Prabhakar authored
Add support for HiHope RZ/G2N Rev.3.0/4.0 main board support based on r8a774b1 SoC. Signed-off-by:
-
Lad Prabhakar authored
Add support for idk-1110wr display as similarly done for Rev.2.0 Signed-off-by:
-
Lad Prabhakar authored
Separate out LVDS specific nodes into common file hihope-rzg2-ex-lvds.dtsi so that this can be re-used by RZ/G2M[N] variants. Signed-off-by:
-
Lad Prabhakar authored
The HiHope RZ/G2M sub board sits below the HiHope RZ/G2M Rev.3.0/4.0 main board. Signed-off-by:
-
Lad Prabhakar authored
Add support for HiHope RZ/G2M Rev.3.0/4.0 main board support based on r8a774a1 SoC. Signed-off-by:
-
Lad Prabhakar authored
Rev.3.0 and Rev.4.0 are identical and can be identified by using GP5_19 and GP5_21. Rev GP5_19 GP5_21 ============================== Rev.3.0 0 0 Rev.4.0 0 1 This patch creates hihope-rev4.dtsi file with Rev.3.0/4.0 specific changes for HopeRun HiHope RZ/G2M[N] boards. Signed-off-by:
-
Lad Prabhakar authored
Separate out Rev.2.0 specific hardware changes into hihope-rev2.dtsi file so that hihope-common.dtsi can be used by all the variants for RZ/G2M[N] boards. LED node names have been updated according to Rev.4.0 schematics. Signed-off-by:
-
Lad Prabhakar authored
The existing DTS files for HiHope RZ/G2N boards are for Rev.2.0 version so reflect the same for the DTS file names so that the existing naming convention can be used for Rev.3.0/4.0 boards. Signed-off-by:
-
Lad Prabhakar authored
The existing DTS files for HiHope RZ/G2M boards are for Rev.2.0 version so reflect the same for the DTS file names so that the existing naming convention can be used for Rev.3.0/4.0 boards. While at it also added a comment about switch SW43 to be OFF for pciec1 to be activated. Signed-off-by:
-
Yoshihiro Shimoda authored
Add IPMMU nodes for r8a77961 (R-Car M3-W+). Signed-off-by:
Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Link: https://lore.kernel.org/r/1591874021-10209-1-git-send-email-yoshihiro.shimoda.uh@renesas.comSigned-off-by:
-
Lad Prabhakar authored
Add the DT nodes needed by MSIOF[0123] interfaces to the SoC dtsi. Signed-off-by:
-
- 15 Jun, 2020 18 commits
-
-
Lad Prabhakar authored
Add support for the camera daughter board which is connected to iWave's RZ/G1H Qseven carrier board. Also enable ttySC[0135] and ethernet1 interfaces. Signed-off-by:
-
Lad Prabhakar authored
Add CMT[01] support to r8a7742 SoC DT. Signed-off-by:
-
Lad Prabhakar authored
This patch instantiates the thermal sensor module with thermal-zone support. Signed-off-by:
-
Lad Prabhakar authored
Enable sound with DMA support on carrier board. DMA transfer uses DVC DMA DMApp [MEM] -> [SRC] -> [DVC] -> [SSIU] -> [SSI] DMA DMApp [MEM] <- [DVC] <- [SRC] <- [SSIU] <- [SSI] Signed-off-by: -
Lad Prabhakar authored
This patch enables SGTL5000 audio codec on the carrier board. Signed-off-by:
-
Lad Prabhakar authored
Add sound support for the RZ/G1H SoC (a.k.a. R8A7742). This work is based on similar work done on the R8A7744 SoC. Signed-off-by:
Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Link: https://lore.kernel.org/r/1590526904-13855-3-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.comSigned-off-by:
-
Lad Prabhakar authored
Enable RWDT and use 60 seconds as default timeout. Signed-off-by:
-
Lad Prabhakar authored
Enable Ethernet AVB on iWave RZ/G1H carrier board. Signed-off-by:
-
Lad Prabhakar authored
Enable the SDHI2 controller on iWave RZ/G1H carrier board. Signed-off-by:
-
Lad Prabhakar authored
Enable SCIFB2 interface on iWave RZ/G1H carrier board. Signed-off-by:
-
Lad Prabhakar authored
Add XHCI support to R8A7742 SoC DT. Signed-off-by:
-
Lad Prabhakar authored
Add USB DMAC and HSUSB device nodes on RZ/G1H SoC dtsi. Signed-off-by:
-
Lad Prabhakar authored
Describe internal PCI bridge devices, USB phy device and link PCI USB devices to USB phy. Signed-off-by:
-
Lad Prabhakar authored
Add a device node for the Watchdog Timer (RWDT) controller on the Renesas RZ/G1H (r8a7742) SoC. Signed-off-by:
Wolfram Sang <wsa+renesas@sang-engineering.com> Link: https://lore.kernel.org/r/1590172641-1556-1-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.comSigned-off-by:
-
Geert Uytterhoeven authored
According to commit 61efb56e ("dt-bindings: arm: gic: Allow combining arm,gic-400 compatible strings"), "arm,gic-400" should be listed first. Signed-off-by:
Andre Przywara <andre.przywara@arm.com> Link: https://lore.kernel.org/r/20200519095431.5650-1-geert+renesas@glider.be
-
Lad Prabhakar authored
Add DT nodes for the Advanced Power Management Units (APMU), and use the enable-method to point out that the APMU should be used for SMP support. Signed-off-by:
-
Lad Prabhakar authored
Define the generic R8A7742 part of the Ether device node. Signed-off-by:
-
Lad Prabhakar authored
Add Ethernet AVB support for R8A7742 SoC. Signed-off-by:
-
