Signed-off-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

The code responsible for reading the version of the mirror bbt was
incorrectly using the descriptor of the main bbt.

Pass the mirror bbt descriptor to 'scan_read_raw' when reading the
version of the mirror bbt.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: stable@vger.kernel.org [v2.6.37+]
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This adds snippets to the i.MX51/53 devicetrees for the nand
flash controller.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

The only relevant change between i.MX51 and i.MX53 is that
a bitfield is shifted one bit to the left.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

The i.MX v3 nand controller (i.MX5) needs two memory resources.
Traditionally we have the AXI resource first. For sorting in this
driver into the devicetree it feels much more natural to have the
IP resource first. This patch swaps the ordering of these two
resources.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

To make the error path simpler and to make subsequent patches
easier.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Previously the remove method was looping and removing all chips,
which is obviously not the right thing to do — left over from when
the driver was organized differently and that was the remove method for
the entire controller.  This would result in bad things happening if
you have more than one NAND chip, and remove the module.

This also fixes priv->dev to properly point to the chip's device rather than
the controller's.  Until now priv->dev was only used for error/debug prints
(and it's an improvement there), so this shouldn't break anything.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Adds JEDEC ID for the 1.8V version of WinBond w25q32.
Signed-off-by: Federico Fuga <fuga@studiofuga.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Prepare the clock before enabling it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

According to its documentation, the NAND_NO_READRDY option is always used
when autoincrement is not supported. Autoincrement support was recently
dropped, so we can drop this options as well (defaulting to "no read ready
check").
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This option was never used and isn't currently used.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Eon's new NAND flash: EN27LN1G08.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This is a clean-up patch which removes the own pseudo-random numbers generator
from the speed- and stress-tests and makes them use the 'random32()' generator
instead.

[dwmw2: Merge later fix for negative offsets]
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

In hardware ecc mode, the flctl now writes and reads the oob data
provided by the user. Additionally the ECC is now returned in normal
page reads, not only when using the explicit NAND_CMD_READOOB command.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

There are multiple reasons for a rewrite:
 - a race exists: when _4ECCEND is set, _4ECCFA may become true too
   meanwhile, which is lost and a non-correctable error is treated as
   correctable.
 - the ECC statistics don't get properly propagated to the base code.
 - empty pages would get marked as corrupted

The rewrite resolves the issues and I hope it gives a more explicit
code flow structure.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

When we use hardware ecc, the flctl is run in so-called "sector access
mode". We can bundle 4 sector accesses when using 2KiB page sizes to read
a whole page at once and speed up things.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

As the equation mtd->writesize == eccsteps * eccsize holds, we can
simplify the code. The second loop of the 1st hunk is never entered,
so we delete it.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

The flctl uses 10 bytes ECC data for every 512 bytes sector. This patch
makes the controller write all 40 bytes instead of 10 bytes only.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

The flctl hardware has changed and a new OOB layout must be adapted for
2KiB page size NAND chips when using hardware ECC.
The related bit fields ECCPOS[0-2] are gone — the bits are marked as
reserved now in the datasheet. As there are no official users of the
hardware ECC so far, they are completely removed.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

When the data transfer between the controller and the NAND chip fails,
we now get notified.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Add the unmapping for the error case and for the driver removal.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This patch is simply an added warning in the comments. Ideally, this patch
need not be merged, but rather, a developer will write a proper solution
that can use the ecc.read_oob_raw and ecc.write_oob_raw interfaces.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

We can clean up the loop logic a bit, here. This refactoring was enabled
in part by:

 Commit bb4a0986 [mtdoops: clean-up new MTD API usage]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

mtd_read_oob() will be expanded a little, so don't leave it in the header
as a static inline function.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

We don't need to open code the divide function, just use div_u64 that
already exists and do the same job. While this is a straightforward
clean up, there is more to that, the real motivation for this.

While building on a cross compiling environment in armel, using gcc
4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5), I was getting the following build
error:

ERROR: "__aeabi_uldivmod" [drivers/mtd/nand/nandsim.ko] undefined!

After investigating with objdump and hand built assembly version
generated with the compiler, I narrowed __aeabi_uldivmod as being
generated from the divide function. When nandsim.c is built with
-fno-inline-functions-called-once, that happens when
CONFIG_DEBUG_SECTION_MISMATCH is enabled, the do_div optimization in
arch/arm/include/asm/div64.h doesn't work as expected with the open
coded divide function: even if the do_div we are using doesn't have a
constant divisor, the compiler still includes the else parts of the
optimized do_div macro, and translates the divisions there to use
__aeabi_uldivmod, instead of only calling __do_div_asm -> __do_div64 and
optimizing/removing everything else out.

So to reproduce, gcc 4.6 plus CONFIG_DEBUG_SECTION_MISMATCH=y and
CONFIG_MTD_NAND_NANDSIM=m should do it, building on armel.

After this change, the compiler does the intended thing even with
-fno-inline-functions-called-once, and optimizes out as expected the
constant handling in the optimized do_div on arm. As this also avoids a
build issue, I'm marking for Stable, as I think is applicable for this
case.
Signed-off-by: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Cc: stable@vger.kernel.org
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

The -EUCLEAN return value applies to mtd_read_oob() as well as mtd_read(), but
only mtd_read() was mentioned in the blurd on bitflip_threshold in the ABI
documentation.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

The gpmi-nand driver uses virt_addr_valid() to check whether a buffer
is suitable for dma. If it's not, a driver allocated buffer is used
instead. Then after a page read the driver allocated buffer must be
copied to the user supplied buffer. This does not happen since commit
7725cc85.

This patch fixes the issue. The bug is encountered with UBI which uses a
vmalloced buffer for the volume table.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: snijsure@grid-net.com
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

The following commit changes the function used to copy from/to
the hardware buffer to memcpy_[from|to]io. This does not work
since the hardware cannot handle the byte accesses used by these
functions. Instead of reverting this patch introduce 32bit
correspondents of these functions.

| commit 5775ba36ea9c760c2d7e697dac04f2f7fc95aa62
| Author: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
| Date:   Tue Apr 24 10:05:22 2012 +0200
|
|    mtd: mxc_nand: fix several sparse warnings about incorrect address space
|
|     Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
|     Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

The intent here was clearly to set result to true if the 0x40000000 flag
was set.  But instead there was a | vs & typo and we always set result
to true.

Artem: check the spec at
wiki.laptop.org/images/5/5c/88ALP01_Datasheet_July_2007.pdf
and this fix looks correct.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

As of edbc454 [mtd: driver _read() returns max_bitflips; mtd_read()
returns -EUCLEAN], 'mtd->bitflip_threshold' must be set for mtd devices
having ECC, prior any 'mtd_read()' call.
Otherwise, 'mtd_read()' will falsely return -EUCLEAN.

Normally, 'mtd->bitflip_threshold' is initialized when the MTD is added.

However, this is too late for NAND MTDs, as 'scan_bbt()' is invoked
prior the existing initialization of 'mtd->bitflip_threshold'.

This is a problem since 'scan_bbt()' calls 'mtd_read()', in the case
of a flash-based bad block table.
It resulted in a falsely reported bitflips indication during BBT read,
which lead to constant scrubbing of the flash BBT blocks.

Initialize 'mtd->bitflip_threshold' to its default value (if not already
set by the driver), prior to invocation of 'scan_bbt()'.
Reported-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

If the privileges given to root threads (3% of allowable memory) or a
negative value of /proc/pid/oom_score_adj happen to exceed the amount of
rss of a thread, its badness score overflows as a result of commit
a7f638f9 ("mm, oom: normalize oom scores to oom_score_adj scale only
for userspace").

Fix this by making the type signed and return 1, meaning the thread is
still eligible for kill, if the value is negative.
Reported-by: Dave Jones <davej@redhat.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull scheduler fixes from Ingo Molnar.

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched: Fix the relax_domain_level boot parameter
  sched: Validate assumptions in sched_init_numa()
  sched: Always initialize cpu-power
  sched: Fix domain iteration
  sched/rt: Fix lockdep annotation within find_lock_lowest_rq()
  sched/numa: Load balance between remote nodes
  sched/x86: Calculate booted cores after construction of sibling_mask

Fix lots of new kernel-doc warnings in kernel/sched/fair.c:

  Warning(kernel/sched/fair.c:3625): No description found for parameter 'env'
  Warning(kernel/sched/fair.c:3625): Excess function parameter 'sd' description in 'update_sg_lb_stats'
  Warning(kernel/sched/fair.c:3735): No description found for parameter 'env'
  Warning(kernel/sched/fair.c:3735): Excess function parameter 'sd' description in 'update_sd_pick_busiest'
  Warning(kernel/sched/fair.c:3735): Excess function parameter 'this_cpu' description in 'update_sd_pick_busiest'
  .. more warnings
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This reverts commit 9e612a00.

It incorrectly finds VGA connectors where none are attached, apparently
not noticing that nothing replied to the EDID queries, and happily using
the default EDID modes that have nothing to do with actual hardware.

That in turn then causes X to fall down to the lowest common
denominator, which is usually the default 1024x768 mode that is in the
default EDID and pretty much anything supports).

I'd suggest that if not relying on the HDP pin, the code should at least
check whether it gets valid EDID data back, rather than just assume
there's something on the VGA connector.

Cc: Dave Airlie <airlied@linux.ie>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull ext4 bug fixes from Theodore Ts'o:
 "This update contains two bug fixes, both destined for the stable tree.
  Perhaps the most important is one which fixes ext4 when used with file
  systems originally formatted for use with ext3, but then later
  converted to take advantage of ext4."

* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: don't set i_flags in EXT4_IOC_SETFLAGS
  ext4: fix the free blocks calculation for ext3 file systems w/ uninit_bg

Pull powerpc fixes from Paul Mackerras:
 "Two small fixes for powerpc:
   - a fix for a regression since 3.2 that causes 4-second (or longer)
     pauses
   - a fix for a potential oops when loading kernel modules on 32-bit
     embedded systems."

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
  powerpc: Fix kernel panic during kernel module load
  powerpc/time: Sanity check of decrementer expiration is necessary

Pull UBI/UBIFS fixes from Artem Bityutskiy:
 "Fix UBI and UBIFS - they refuse to work without debugfs.  This was
  broken by the 3.5-rc1 UBI/UBIFS changes when we removed the debugging
  Kconfig switches.

  Also, correct locking in 'ubi_wl_flush()' - it was extended to support
  flushing a specific LEB in 3.5-rc1, and the locking was sub-optimal."

* tag 'upstream-3.5-rc2' of git://git.infradead.org/linux-ubifs:
  UBI: correct ubi_wl_flush locking
  UBIFS: fix debugfs-less systems support
  UBI: fix debugfs-less systems support