- 10 Sep, 2015 11 commits
-
-
Nimrod Andy authored
There exist one issue by below case that case system hang: ifconfig eth0 down ifconfig eth0 hw ether 00:10:19:19:81:19 After eth0 down, all fec clocks are gated off. In the .fec_set_mac_address() function, it will set new MAC address to registers, which causes system hang. So it needs to add netif status check to avoid registers access when clocks are gated off. Until eth0 up the new MAC address are wrote into related registers. V2: As Lucas Stach's suggestion, add a comment in the code to explain why it needed. CC: Lucas Stach <l.stach@pengutronix.de> CC: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
Fugang Duan <B38611@freescale.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Hayes Wang says: ==================== r8152: fix the autoresume may fail Fix the autosuspend issues which occur about linking change. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
hayeswang authored
Fix the runtime suspend issues result from the linking change. Case 1: a) link down occurs. b) driver disable tx/rx. c) autosuspend occurs. d) hw linking up. e) device suspends without enabling tx/rx. f) couldn't wake up when receiving packets. Case 2: a) Nway results in linking down. b) autosuspend occurs. c) device suspends. d) device may not wake up when linking up. Signed-off-by:
Hayes Wang <hayeswang@realtek.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
hayeswang authored
Split DRIVER_VERSION into NETNEXT_VERSION and NET_VERSION. Then, according to the value of DRIVER_VERSION, we could know which patches are used generally without comparing the source code. Signed-off-by:
Hayes Wang <hayeswang@realtek.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Wu Fengguang authored
net/ipv6/route.c:2946:3-8: WARNING: NULL check before freeing functions like kfree, debugfs_remove, debugfs_remove_recursive or usb_free_urb is not needed. Maybe consider reorganizing relevant code to avoid passing NULL values. NULL check before some freeing functions is not needed. Based on checkpatch warning "kfree(NULL) is safe this check is probably not required" and kfreeaddr.cocci by Julia Lawall. Generated by: scripts/coccinelle/free/ifnullfree.cocci CC: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by:
Fengguang Wu <fengguang.wu@intel.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Woojung.Huh@microchip.com authored
Add Microchip LAN88XX phy driver for phylib. Signed-off-by:
Woojung Huh <woojung.huh@microchip.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Alexey Brodkin authored
Current check of phydev with IS_ERR(phydev) may make not much sense because of_phy_connect() returns NULL on failure instead of error value. Still for checking result of phy_connect() IS_ERR() makes perfect sense. So let's use combined check IS_ERR_OR_NULL() that covers both cases. Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: linux-kernel@vger.kernel.org Cc: stable@vger.kernel.org Cc: David Miller <davem@davemloft.net> Signed-off-by:
Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Rasmus Villemoes authored
In all cases, mbx->req.arg and mbx->rsp.arg have just been allocated using kcalloc(), so these six memsets are redundant. Signed-off-by:
Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Rasmus Villemoes authored
The double memset is a little ugly; using kzalloc avoids it altogether. Signed-off-by:
Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Rasmus Villemoes authored
Using kzalloc saves a tiny bit on .text. Signed-off-by:
Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Rasmus Villemoes authored
We save a little .text and get rid of the sizeof(...) style inconsistency. Signed-off-by:
Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- 09 Sep, 2015 17 commits
-
-
Phil Sutter authored
This switches IPv6 policy routing to use the shared fib_default_rule_pref() function of IPv4 and DECnet. It is also used in multicast routing for IPv4 as well as IPv6. The motivation for this patch is a complaint about iproute2 behaving inconsistent between IPv4 and IPv6 when adding policy rules: Formerly, IPv6 rules were assigned a fixed priority of 0x3FFF whereas for IPv4 the assigned priority value was decreased with each rule added. Since then all users of the default_pref field have been converted to assign the generic function fib_default_rule_pref(), fib_nl_newrule() may just use it directly instead. Therefore get rid of the function pointer altogether and make fib_default_rule_pref() static, as it's not used outside fib_rules.c anymore. Signed-off-by:
Phil Sutter <phil@nwl.cc> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Tobias Klauser authored
For !CONFIG_OF of_get_property() is defined to always return NULL. Thus there's no need to protect the call to of_get_property() with #ifdef CONFIG_OF. Signed-off-by:
Tobias Klauser <tklauser@distanz.ch> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Florian Fainelli authored
The macro to write 64-bits quantities to the 32-bits register swapped the value and offsets arguments, we want to preserve the ordering of the arguments with respect to how writel() is implemented for instance: value first, offset/base second. Fixes: 246d7f77 ("net: dsa: add Broadcom SF2 switch driver") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Reviewed-by:
Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Alexei Starovoitov authored
when the verifier log is enabled the print_bpf_insn() is doing bpf_alu_string[BPF_OP(insn->code) >> 4] and bpf_jmp_string[BPF_OP(insn->code) >> 4] where BPF_OP is a 4-bit instruction opcode. Malformed insns can cause out of bounds access. Fix it by sizing arrays appropriately. The bug was found by clang address sanitizer with libfuzzer. Reported-by:
Yonghong Song <yhs@plumgrid.com> Signed-off-by:
Alexei Starovoitov <ast@plumgrid.com> Acked-by:
Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Roopa Prabhu authored
Problem: The ecmp route replace support for ipv6 in the kernel, deletes the existing ecmp route too early, ie when it installs the first nexthop. If there is an error in installing the subsequent nexthops, its too late to recover the already deleted existing route leaving the fib in an inconsistent state. This patch reduces the possibility of this by doing the following: a) Changes the existing multipath route add code to a two stage process: build rt6_infos + insert them ip6_route_add rt6_info creation code is moved into ip6_route_info_create. b) This ensures that most errors are caught during building rt6_infos and we fail early c) Separates multipath add and del code. Because add needs the special two stage mode in a) and delete essentially does not care. d) In any event if the code fails during inserting a route again, a warning is printed (This should be unlikely) Before the patch: $ip -6 route show 3000:1000:1000:1000::2 via fe80::202:ff:fe00:b dev swp49s0 metric 1024 3000:1000:1000:1000::2 via fe80::202:ff:fe00:d dev swp49s1 metric 1024 3000:1000:1000:1000::2 via fe80::202:ff:fe00:f dev swp49s2 metric 1024 /* Try replacing the route with a duplicate nexthop */ $ip -6 route change 3000:1000:1000:1000::2/128 nexthop via fe80::202:ff:fe00:b dev swp49s0 nexthop via fe80::202:ff:fe00:d dev swp49s1 nexthop via fe80::202:ff:fe00:d dev swp49s1 RTNETLINK answers: File exists $ip -6 route show /* previously added ecmp route 3000:1000:1000:1000::2 dissappears from * kernel */ After the patch: $ip -6 route show 3000:1000:1000:1000::2 via fe80::202:ff:fe00:b dev swp49s0 metric 1024 3000:1000:1000:1000::2 via fe80::202:ff:fe00:d dev swp49s1 metric 1024 3000:1000:1000:1000::2 via fe80::202:ff:fe00:f dev swp49s2 metric 1024 /* Try replacing the route with a duplicate nexthop */ $ip -6 route change 3000:1000:1000:1000::2/128 nexthop via fe80::202:ff:fe00:b dev swp49s0 nexthop via fe80::202:ff:fe00:d dev swp49s1 nexthop via fe80::202:ff:fe00:d dev swp49s1 RTNETLINK answers: File exists $ip -6 route show 3000:1000:1000:1000::2 via fe80::202:ff:fe00:b dev swp49s0 metric 1024 3000:1000:1000:1000::2 via fe80::202:ff:fe00:d dev swp49s1 metric 1024 3000:1000:1000:1000::2 via fe80::202:ff:fe00:f dev swp49s2 metric 1024 Fixes: 27596472 ("ipv6: fix ECMP route replacement") Signed-off-by:
Roopa Prabhu <roopa@cumulusnetworks.com> Reviewed-by:
Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Acked-by:
Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Daniel Borkmann authored
We may already have gotten a proper fd struct through fdget(), so whenever we return at the end of an map operation, we need to call fdput(). However, each map operation from syscall side first probes CHECK_ATTR() to verify that unused fields in the bpf_attr union are zero. In case of malformed input, we return with error, but the lookup to the map_fd was already performed at that time, so that we return without an corresponding fdput(). Fix it by performing an fdget() only right before bpf_map_get(). The fdget() invocation on maps in the verifier is not affected. Fixes: db20fd2b ("bpf: add lookup/update/delete/iterate methods to BPF maps") Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Acked-by:
Alexei Starovoitov <ast@plumgrid.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Sasha Levin authored
There was no verification that an underlying transport exists when creating a connection, this would cause dereferencing a NULL ptr. It might happen on sockets that weren't properly bound before attempting to send a message, which will cause a NULL ptr deref: [135546.047719] kasan: GPF could be caused by NULL-ptr deref or user memory accessgeneral protection fault: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC KASAN [135546.051270] Modules linked in: [135546.051781] CPU: 4 PID: 15650 Comm: trinity-c4 Not tainted 4.2.0-next-20150902-sasha-00041-gbaa1222-dirty #2527 [135546.053217] task: ffff8800835bc000 ti: ffff8800bc708000 task.ti: ffff8800bc708000 [135546.054291] RIP: __rds_conn_create (net/rds/connection.c:194) [135546.055666] RSP: 0018:ffff8800bc70fab0 EFLAGS: 00010202 [135546.056457] RAX: dffffc0000000000 RBX: 0000000000000f2c RCX: ffff8800835bc000 [135546.057494] RDX: 0000000000000007 RSI: ffff8800835bccd8 RDI: 0000000000000038 [135546.058530] RBP: ffff8800bc70fb18 R08: 0000000000000001 R09: 0000000000000000 [135546.059556] R10: ffffed014d7a3a23 R11: ffffed014d7a3a21 R12: 0000000000000000 [135546.060614] R13: 0000000000000001 R14: ffff8801ec3d0000 R15: 0000000000000000 [135546.061668] FS: 00007faad4ffb700(0000) GS:ffff880252000000(0000) knlGS:0000000000000000 [135546.062836] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b [135546.063682] CR2: 000000000000846a CR3: 000000009d137000 CR4: 00000000000006a0 [135546.064723] Stack: [135546.065048] ffffffffafe2055c ffffffffafe23fc1 ffffed00493097bf ffff8801ec3d0008 [135546.066247] 0000000000000000 00000000000000d0 0000000000000000 ac194a24c0586342 [135546.067438] 1ffff100178e1f78 ffff880320581b00 ffff8800bc70fdd0 ffff880320581b00 [135546.068629] Call Trace: [135546.069028] ? __rds_conn_create (include/linux/rcupdate.h:856 net/rds/connection.c:134) [135546.069989] ? rds_message_copy_from_user (net/rds/message.c:298) [135546.071021] rds_conn_create_outgoing (net/rds/connection.c:278) [135546.071981] rds_sendmsg (net/rds/send.c:1058) [135546.072858] ? perf_trace_lock (include/trace/events/lock.h:38) [135546.073744] ? lockdep_init (kernel/locking/lockdep.c:3298) [135546.074577] ? rds_send_drop_to (net/rds/send.c:976) [135546.075508] ? __might_fault (./arch/x86/include/asm/current.h:14 mm/memory.c:3795) [135546.076349] ? __might_fault (mm/memory.c:3795) [135546.077179] ? rds_send_drop_to (net/rds/send.c:976) [135546.078114] sock_sendmsg (net/socket.c:611 net/socket.c:620) [135546.078856] SYSC_sendto (net/socket.c:1657) [135546.079596] ? SYSC_connect (net/socket.c:1628) [135546.080510] ? trace_dump_stack (kernel/trace/trace.c:1926) [135546.081397] ? ring_buffer_unlock_commit (kernel/trace/ring_buffer.c:2479 kernel/trace/ring_buffer.c:2558 kernel/trace/ring_buffer.c:2674) [135546.082390] ? trace_buffer_unlock_commit (kernel/trace/trace.c:1749) [135546.083410] ? trace_event_raw_event_sys_enter (include/trace/events/syscalls.h:16) [135546.084481] ? do_audit_syscall_entry (include/trace/events/syscalls.h:16) [135546.085438] ? trace_buffer_unlock_commit (kernel/trace/trace.c:1749) [135546.085515] rds_ib_laddr_check(): addr 36.74.25.172 ret -99 node type -1 Acked-by:
Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by:
Sasha Levin <sasha.levin@oracle.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David Vrabel authored
Commit f48da8b1 (xen-netback: fix unlimited guest Rx internal queue and carrier flapping) introduced a regression. The PV frontend in IPXE only places 4 requests on the guest Rx ring. Since netback required at least (MAX_SKB_FRAGS + 1) slots, IPXE could not receive any packets. a) If GSO is not enabled on the VIF, fewer guest Rx slots are required for the largest possible packet. Calculate the required slots based on the maximum GSO size or the MTU. This calculation of the number of required slots relies on 1650d545 (xen-netback: always fully coalesce guest Rx packets) which present in 4.0-rc1 and later. b) Reduce the Rx stall detection to checking for at least one available Rx request. This is fine since we're predominately concerned with detecting interfaces which are down and thus have zero available Rx requests. Signed-off-by:
David Vrabel <david.vrabel@citrix.com> Reviewed-by:
Wei Liu <wei.liu2@citrix.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Hariprasad Shenai says: ==================== cxgb4: Fix tx flit calculation and wc stat configuration This patch series fixes the following: Patch 1/2 fixes tx flit calculation, which if wrong can lead to stall, hang, data corrpution, write combining failure. Patch 2/2 fixes PCI-E write combining stats configuration. This patch series has been created against net tree and includes patches on cxgb4 driver. We have included all the maintainers of respective drivers. Kindly review the change and let us know in case of any review comments. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Hariprasad Shenai authored
The write-combining configuration register SGE_STAT_CFG_A needs to be configured after FW initializes the adapter, else FW will reset the configuration Signed-off-by:
Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Hariprasad Shenai authored
In commit 0aac3f56 ("cxgb4: Add comment for calculate tx flits and sge length code") introduced a regression where tx flit calculation is going wrong, which can lead to data corruption, hang, stall and write-combining failure. Fixing it. Signed-off-by:
Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Atsushi Nemoto authored
Call netif_carrier_off() prior to register_netdev(), otherwise userspace can see incorrect link state. Signed-off-by:
Atsushi Nemoto <nemoto@toshiba-tops.co.jp> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Kolmakov Dmitriy authored
If an attempt to wake up users of broadcast link is made when there is no enough place in send queue than it may hang up inside the tipc_sk_rcv() function since the loop breaks only after the wake up queue becomes empty. This can lead to complete CPU stall with the following message generated by RCU: INFO: rcu_sched self-detected stall on CPU { 0} (t=2101 jiffies g=54225 c=54224 q=11465) Task dump for CPU 0: tpch R running task 0 39949 39948 0x0000000a ffffffff818536c0 ffff88181fa037a0 ffffffff8106a4be 0000000000000000 ffffffff818536c0 ffff88181fa037c0 ffffffff8106d8a8 ffff88181fa03800 0000000000000001 ffff88181fa037f0 ffffffff81094a50 ffff88181fa15680 Call Trace: <IRQ> [<ffffffff8106a4be>] sched_show_task+0xae/0x120 [<ffffffff8106d8a8>] dump_cpu_task+0x38/0x40 [<ffffffff81094a50>] rcu_dump_cpu_stacks+0x90/0xd0 [<ffffffff81097c3b>] rcu_check_callbacks+0x3eb/0x6e0 [<ffffffff8106e53f>] ? account_system_time+0x7f/0x170 [<ffffffff81099e64>] update_process_times+0x34/0x60 [<ffffffff810a84d1>] tick_sched_handle.isra.18+0x31/0x40 [<ffffffff810a851c>] tick_sched_timer+0x3c/0x70 [<ffffffff8109a43d>] __run_hrtimer.isra.34+0x3d/0xc0 [<ffffffff8109aa95>] hrtimer_interrupt+0xc5/0x1e0 [<ffffffff81030d52>] ? native_smp_send_reschedule+0x42/0x60 [<ffffffff81032f04>] local_apic_timer_interrupt+0x34/0x60 [<ffffffff810335bc>] smp_apic_timer_interrupt+0x3c/0x60 [<ffffffff8165a3fb>] apic_timer_interrupt+0x6b/0x70 [<ffffffff81659129>] ? _raw_spin_unlock_irqrestore+0x9/0x10 [<ffffffff8107eb9f>] __wake_up_sync_key+0x4f/0x60 [<ffffffffa313ddd1>] tipc_write_space+0x31/0x40 [tipc] [<ffffffffa313dadf>] filter_rcv+0x31f/0x520 [tipc] [<ffffffffa313d699>] ? tipc_sk_lookup+0xc9/0x110 [tipc] [<ffffffff81659259>] ? _raw_spin_lock_bh+0x19/0x30 [<ffffffffa314122c>] tipc_sk_rcv+0x2dc/0x3e0 [tipc] [<ffffffffa312e7ff>] tipc_bclink_wakeup_users+0x2f/0x40 [tipc] [<ffffffffa313ce26>] tipc_node_unlock+0x186/0x190 [tipc] [<ffffffff81597c1c>] ? kfree_skb+0x2c/0x40 [<ffffffffa313475c>] tipc_rcv+0x2ac/0x8c0 [tipc] [<ffffffffa312ff58>] tipc_l2_rcv_msg+0x38/0x50 [tipc] [<ffffffff815a76d3>] __netif_receive_skb_core+0x5a3/0x950 [<ffffffff815a98d3>] __netif_receive_skb+0x13/0x60 [<ffffffff815a993e>] netif_receive_skb_internal+0x1e/0x90 [<ffffffff815aa138>] napi_gro_receive+0x78/0xa0 [<ffffffffa07f93f4>] tg3_poll_work+0xc54/0xf40 [tg3] [<ffffffff81597c8c>] ? consume_skb+0x2c/0x40 [<ffffffffa07f9721>] tg3_poll_msix+0x41/0x160 [tg3] [<ffffffff815ab0f2>] net_rx_action+0xe2/0x290 [<ffffffff8104b92a>] __do_softirq+0xda/0x1f0 [<ffffffff8104bc26>] irq_exit+0x76/0xa0 [<ffffffff81004355>] do_IRQ+0x55/0xf0 [<ffffffff8165a12b>] common_interrupt+0x6b/0x6b <EOI> The issue occurs only when tipc_sk_rcv() is used to wake up postponed senders: tipc_bclink_wakeup_users() // wakeupq - is a queue which consists of special // messages with SOCK_WAKEUP type. tipc_sk_rcv(wakeupq) ... while (skb_queue_len(inputq)) { filter_rcv(skb) // Here the type of message is checked // and if it is SOCK_WAKEUP then // it tries to wake up a sender. tipc_write_space(sk) wake_up_interruptible_sync_poll() } After the sender thread is woke up it can gather control and perform an attempt to send a message. But if there is no enough place in send queue it will call link_schedule_user() function which puts a message of type SOCK_WAKEUP to the wakeup queue and put the sender to sleep. Thus the size of the queue actually is not changed and the while() loop never exits. The approach I proposed is to wake up only senders for which there is enough place in send queue so the described issue can't occur. Moreover the same approach is already used to wake up senders on unicast links. I have got into the issue on our product code but to reproduce the issue I changed a benchmark test application (from tipcutils/demos/benchmark) to perform the following scenario: 1. Run 64 instances of test application (nodes). It can be done on the one physical machine. 2. Each application connects to all other using TIPC sockets in RDM mode. 3. When setup is done all nodes start simultaneously send broadcast messages. 4. Everything hangs up. The issue is reproducible only when a congestion on broadcast link occurs. For example, when there are only 8 nodes it works fine since congestion doesn't occur. Send queue limit is 40 in my case (I use a critical importance level) and when 64 nodes send a message at the same moment a congestion occurs every time. Signed-off-by:
Dmitry S Kolmakov <kolmakov.dmitriy@huawei.com> Reviewed-by:
Jon Maloy <jon.maloy@ericsson.com> Acked-by:
Ying Xue <ying.xue@windriver.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Barry Song authored
Signed-off-by:
Barry Song <Baohua.Song@csr.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Vivien Didelot authored
Remove the unnecessary switchdev.h include from br_netlink.c. Signed-off-by:
Vivien Didelot <vivien.didelot@savoirfairelinux.com> Acked-by:
Jiri Pirko <jiri@resnulli.us> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Vivien Didelot authored
Since __vlan_del can return an error code, change its inner function __vlan_vid_del to return an eventual error from switchdev_port_obj_del. Signed-off-by:
Vivien Didelot <vivien.didelot@savoirfairelinux.com> Acked-by:
Jiri Pirko <jiri@resnulli.us> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Florian Fainelli authored
The comparison check between cur_hw_state and hw_state is currently invalid because cur_hw_state is right shifted by G_MISTP_SHIFT, while hw_state is not, so we end-up comparing bits 2:0 with bits 7:5, which is going to cause an additional aging to occur. Fix this by not shifting cur_hw_state while reading it, but instead, mask the value with the appropriately shitfted bitmask. The other problem with the fast-ageing process is that we did not set the EN_AGE_DYNAMIC bit to request the ageing to occur for dynamically learned MAC addresses. Finally, write back 0 to the FAST_AGE_CTRL register to avoid leaving spurious bits sets from one operation to the other. Fixes: 12f460f2 ("net: dsa: bcm_sf2: add HW bridging support") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- 08 Sep, 2015 2 commits
-
-
Julien Grall authored
The function device_get_mac_address is trying different property names in order to get the mac address. To check the return value, the variable addr (which contain the buffer pass by the caller) will be re-used. This means that if the previous property is not found, the next property will be read using a NULL buffer. Therefore it's only possible to retrieve the mac if node contains a property "mac-address". Fix it by using a temporary buffer for the return value. This has been introduced by commit 4c96b7dc "Add a matching set of device_ functions for determining mac/phy" Signed-off-by:
Julien Grall <julien.grall@citrix.com> Cc: Jeremy Linton <jeremy.linton@arm.com> Cc: David S. Miller <davem@davemloft.net> Reviewed-by:
Jeremy Linton <jeremy.linton@arm.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Eugene Shatokhin authored
The race may happen when a device (e.g. YOTA 4G LTE Modem) is unplugged while the system is downloading a large file from the Net. Hardware breakpoints and Kprobes with delays were used to confirm that the race does actually happen. The race is on skb_queue ('next' pointer) between usbnet_stop() and rx_complete(), which, in turn, calls usbnet_bh(). Here is a part of the call stack with the code where the changes to the queue happen. The line numbers are for the kernel 4.1.0: *0 __skb_unlink (skbuff.h:1517) prev->next = next; *1 defer_bh (usbnet.c:430) spin_lock_irqsave(&list->lock, flags); old_state = entry->state; entry->state = state; __skb_unlink(skb, list); spin_unlock(&list->lock); spin_lock(&dev->done.lock); __skb_queue_tail(&dev->done, skb); if (dev->done.qlen == 1) tasklet_schedule(&dev->bh); spin_unlock_irqrestore(&dev->done.lock, flags); *2 rx_complete (usbnet.c:640) state = defer_bh(dev, skb, &dev->rxq, state); At the same time, the following code repeatedly checks if the queue is empty and reads these values concurrently with the above changes: *0 usbnet_terminate_urbs (usbnet.c:765) /* maybe wait for deletions to finish. */ while (!skb_queue_empty(&dev->rxq) && !skb_queue_empty(&dev->txq) && !skb_queue_empty(&dev->done)) { schedule_timeout(msecs_to_jiffies(UNLINK_TIMEOUT_MS)); set_current_state(TASK_UNINTERRUPTIBLE); netif_dbg(dev, ifdown, dev->net, "waited for %d urb completions\n", temp); } *1 usbnet_stop (usbnet.c:806) if (!(info->flags & FLAG_AVOID_UNLINK_URBS)) usbnet_terminate_urbs(dev); As a result, it is possible, for example, that the skb is removed from dev->rxq by __skb_unlink() before the check "!skb_queue_empty(&dev->rxq)" in usbnet_terminate_urbs() is made. It is also possible in this case that the skb is added to dev->done queue after "!skb_queue_empty(&dev->done)" is checked. So usbnet_terminate_urbs() may stop waiting and return while dev->done queue still has an item. Locking in defer_bh() and usbnet_terminate_urbs() was revisited to avoid this race. Signed-off-by:
Eugene Shatokhin <eugene.shatokhin@rosalab.ru> Reviewed-by:
Bjørn Mork <bjorn@mork.no> Acked-by:
Oliver Neukum <oneukum@suse.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- 07 Sep, 2015 8 commits
-
-
françois romieu authored
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c: In function ‘init_one’: drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:4579:8: warning: ‘chip’ may be used uninitialized in this function [-Wmaybe-uninitialized] chip |= CHELSIO_CHIP_CODE(CHELSIO_T4, pl_rev); ^ drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:4571:11: note: ‘chip’ was declared here int ver, chip; ^ Fixes: d86bd29e ("cxgb4/cxgb4vf: read the correct bits of PL Who Am I register") Signed-off-by:
Francois Romieu <romieu@fr.zoreil.com> Cc: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Sergei Shtylyov authored
I've noticed that fixed_phy_register() ignores its 'irq' parameter instead of passing it to fixed_phy_add(). Luckily, fixed_phy_register() seems to always be called with PHY_POLL for 'irq'... :-) Fixes: a7595121 ("net: phy: extend fixed driver with fixed_phy_register()") Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Acked-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Joe Stringer authored
There's no particular desire to have conntrack action support in Open vSwitch as an independently configurable bit, rather just to ensure there is not a hard dependency. This exposed option doesn't accurately reflect the conntrack dependency when enabled, so simplify this by removing the option. Compile the support if NF_CONNTRACK is enabled. Fixes: 7f8a436e ("openvswitch: Add conntrack action") Signed-off-by:
Joe Stringer <joestringer@nicira.com> Acked-by:
Pravin B Shelar <pshelar@nicira.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Vivien Didelot authored
The Marvell 88E6171 switch is in the 88E6351 family, which supports 802.1Q, thus add support from the generic mv88e6xxx functions. Signed-off-by:
Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Merge tag 'mac80211-for-davem-2015-09-04' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211 Johannes Berg says: ==================== For the first round of fixes, we have this: * fix for the sizeof() pointer type issue * a fix for regulatory getting into a restore loop * a fix for rfkill global 'all' state, it needs to be stored everywhere to apply correctly to new rfkill instances * properly refuse CQM RSSI when it cannot actually be used * protect HT TDLS traffic properly in non-HT networks * don't incorrectly advertise 80 MHz support when not allowed ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Geert Uytterhoeven authored
If NO_DMA=y: ERROR: "dma_alloc_coherent" [drivers/net/ethernet/synopsys/dwc_eth_qos.ko] undefined! ERROR: "dma_free_coherent" [drivers/net/ethernet/synopsys/dwc_eth_qos.ko] undefined! ERROR: "dma_unmap_single" [drivers/net/ethernet/synopsys/dwc_eth_qos.ko] undefined! ERROR: "dma_map_page" [drivers/net/ethernet/synopsys/dwc_eth_qos.ko] undefined! ERROR: "dma_mapping_error" [drivers/net/ethernet/synopsys/dwc_eth_qos.ko] undefined! ERROR: "dma_map_single" [drivers/net/ethernet/synopsys/dwc_eth_qos.ko] undefined! Signed-off-by:
Geert Uytterhoeven <geert@linux-m68k.org> Acked-by:
Lars Persson <larper@axis.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Geert Uytterhoeven authored
drivers/net/vxlan.c: In function ‘vxlan_udp_encap_recv’: drivers/net/vxlan.c:1226: warning: ‘info’ may be used uninitialized in this function While this warning is a false positive, it can be killed easily by getting rid of the pointer intermediary and referring directly to the ip_tunnel_info structure. Signed-off-by:
Geert Uytterhoeven <geert@linux-m68k.org> Reviewed-by:
Jiri Benc <jbenc@redhat.com> Acked-by:
Thomas Graf <tgraf@suug.ch> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Geert Uytterhoeven authored
net/usb/lan78xx.c: In function ‘lan78xx_link_reset’: net/usb/lan78xx.c:1107: warning: comparison is always false due to limited range of data type net/usb/lan78xx.c:1111: warning: comparison is always false due to limited range of data type Assigning return values that can be negative error codes to "u16" variables makes them positive, ignoring the errors. Hence use "int" instead. Drop the "unlikely"s (unlikely considered harmful) and propagate the actual error values instead of overriding them to -EIO while we're at it. Signed-off-by:
Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- 06 Sep, 2015 2 commits
-
-
Sowmini Varadhan authored
Only return a conn if the rds_conn_net(conn) matches the struct net passed to rds_conn_lookup(). Fixes: 467fa153 ("RDS-TCP: Support multiple RDS-TCP listen endpoints, one per netns.") Signed-off-by:
Sowmini Varadhan <sowmini.varadhan@oracle.com> Acked-by:
Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Maciej S. Szmigiero authored
If fec MDIO write method succeeds its return value comes from call to pm_runtime_get_sync(). But pm_runtime_get_sync() can also return 1. In case of Micrel KSZ9031 PHY this value will then be returned along the call chain of phy_write() -> ksz9031_extended_write() -> ksz9031_center_flp_timing() -> ksz9031_config_init() -> phy_init_hw() -> phy_attach_direct() -> phy_connect_direct(). Then phy_connect() will cast it into a pointer using ERR_PTR(), which then fec_enet_mii_probe() will try to dereference resulting in an oops. Fix it by normalizing return value of pm_runtime_get_sync() to be zero if positive in MDIO write method. Fixes: 8fff755e ("net: fec: Ensure clocks are enabled while using mdio bus") Signed-off-by:
Maciej Szmigiero <mail@maciej.szmigiero.name> Acked-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
David S. Miller <davem@davemloft.net>
-