i.MX device tree changes for 5.14:

- New board support: i.MX6Q DaSheng COM-9XX SBC board, i.MX28 based XEA
  board, GE B1x5v2 boards.
- A series from Christoph Niedermaier to correct imx6q-dhcom
  descriptions, add device aliases and ethernet VIO regulator.
- Correct Ethernet node name for imx51-digi-connectcore-som and
  imx53-ard board to comply DT schema.
- A couple of update on imx6dl-yapp4 board, configuring OLED display
  segment offset, and using aliases to set custom MMC device indexes.
- A series from Oleksij Rempel and Robin van der Gracht to update
  Protonic boards: imx6dl-prtvt7, imx6dl-plym2m and imx6qdl-vicut1.
- A series from Shengjiu Wang to improve various audio support on NXP
  reference boards.
- Rename pinfunc for i.MX25 GPIO_[A-F] pads for consistency.

* tag 'imx-dt-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (30 commits)
  ARM: dts: imx6: Add GE B1x5v2
  ARM: dts: imx6q-dhcom: Add ethernet VIO regulator
  ARM: dts: imx6q-dhcom: Add aliases for i2c, serial and rtc
  ARM: dts: imx6q-dhcom: Add gpios pinctrl for i2c bus recovery
  ARM: dts: imx6q-dhcom: Fix ethernet plugin detection problems
  ARM: dts: imx6q-dhcom: Fix ethernet reset time properties
  ARM: dts: imx6dl-prtvt7: Remove unused 'sound-dai-cells' from ssi1 node
  ARM: dts: imx6dl-prtvt7: The sgtl5000 uses i2s not ac97
  ARM: dts: imx6qdl-vicut1: add interrupt-counter nodes
  ARM: dts: imx6dl-prtvt7: Enable the VPU
  ARM: dts: imx6dl: enable touchscreen debounce filter on PLYM2M and PRTVT7 boards
  ARM: dts: imx6dl-plym2m: remove touchscreen-size-* properties
  ARM: dts: imx6dl-prtvt7: fix PWM cell count for the backlight node.
  ARM: dts: imx6dl-prtvt7: Remove backlight enable gpio
  ARM: dts: imx6dl-prtvt7: add TSC2046 touchscreen node
  ARM: dts: imx53-ard: Correct Ethernet node name
  ARM: dts: i.MX51: digi-connectcore-som: Correct Ethernet node name
  ARM: dts: imx6dl-riotboard: configure PHY clock and set proper EEE value
  ARM: dts: imx6: edmqmx6: set phy-mode to RGMII-ID
  ARM: dts: imx6qdl-sabresd: Configure the gpio for hp detect
  ...

Link: https://lore.kernel.org/r/20210613082544.16067-4-shawnguo@kernel.orgSigned-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'imx-bindings-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt

i.MX dt-bindings update for 5.14:

- Add vendor prefixes for congatec GmbH and DaSheng, Inc.
- Add compatibles for i.MX6Q DaSheng COM-9XX SBC, GE B1x5pv2 and
  i.MX8MM GW7901 boards.
- Add an optional 'resets' property for i.MX GPCv2 bindings.

* tag 'imx-bindings-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  dt-bindings: arm: fsl: add GE B1x5pv2 boards
  dt-bindings: vendor-prefixes: add congatec
  dt-bindings: imx: gpcv2: add support for optional resets
  dt-bindings: arm: imx: Add i.mx6q DaSheng COM-9XX SBC
  dt-bindings: add dasheng vendor prefix
  dt-bindings: arm: imx: add imx8mm gw7901 support

Link: https://lore.kernel.org/r/20210613082544.16067-3-shawnguo@kernel.orgSigned-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'keystone_dts_for_5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into arm/dt

ARM: DTS: Keystone K2G cleanup for v5.13

  - Rename message manager node
  - Rename the TI-SCI node and clock
  - assign clock to McAsp

* tag 'keystone_dts_for_5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
  ARM: dts: keystone: k2g-evm: Move audio oscillator assigned clock to mcasp
  ARM: dts: keystone: k2g: Rename the TI-SCI clocks node name
  ARM: dts: keystone: k2g: Rename the TI-SCI node
  ARM: dts: keystone: k2g: Rename message-manager node

Link: https://lore.kernel.org/r/1623564020-9958-1-git-send-email-santosh.shilimkar@oracle.comSigned-off-by: Olof Johansson <olof@lixom.net>

The SL3516 SoC has a crypto offloader IP.
This patch adds it on the gemini SoC Device-tree.

Link: https://lore.kernel.org/r/20210611220501.684997-1-linus.walleij@linaro.orgSigned-off-by: Corentin Labbe <clabbe@baylibre.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'sunxi-dt-for-5.14-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt

Our usual bunch of patches to improve the Allwinner SoCs support,
mainly:
  - I2S Support for the V3
  - Audio Codec Support for the V3s
  - DMA support for the V3s
  - PWM support for the V3s
  - Support for Bluetooth Audio on the pinephone
  - Add A10-like timers to the A64 and R40
  - New boards: Forlinx OKA40i-C, Forlinx OKA40i-C, NanoPi R1S H5

* tag 'sunxi-dt-for-5.14-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (29 commits)
  ARM: dts: sun8i: v3s: enable emac for zero Dock
  arm64: dts: allwinner: pinephone: Set audio card name
  ARM: dts: sun8i: r40: Add timer node
  ARM: dts: sun8i: V3: add I2S interface to V3 dts
  dt-bindings: sound: sun4i-i2s: add Allwinner V3 I2S compatible
  ARM: dts: sun8i: V3: add codec analog frontend to V3 dts
  ASoC: dt-bindings: sun8i-a23-codec-analog: add compatible for Allwinner V3
  ARM: dts: sun8i: v3s: add analog codec and frontend to v3s dts
  ARM: dts: sun8i: v3s: add DMA properties to peripherals supporting DMA
  ARM: dts: sun8i: v3s: add DMA controller to v3s dts
  ARM: dts: sun8i: v3s: add pwm controller to v3s dts
  dt-bindings: pwm: allwinner: add v3s pwm compatible
  arm64: dts: allwinner: h5: Add NanoPi R1S H5 support
  dt-bindings: arm: Add NanoPi R1S H5
  arm64: dts: allwinner: pinephone: Add support for Bluetooth audio
  arm64: dts: allwinner: a64: Allow multiple DAI links
  arm64: dts: allwinner: a64: Add pinmux nodes for AIF2/AIF3
  arm64: dts: allwinner: a64: Allow using multiple codec DAIs
  ARM: dts: sun8i-a33: Allow using multiple codec DAIs
  ASoC: dt-bindings: sun8i-codec: Increase #sound-dai-cells
  ...

Link: https://lore.kernel.org/r/96cc77ec-139d-4685-8a66-a60964cf39fd.lettre@localhostSigned-off-by: Olof Johansson <olof@lixom.net>

AT91 dt for 5.14:

- A fix for sama5d4 gpio mux
- A trivial fix for DT documentation

* tag 'at91-dt-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
  dt-bindings: i2c: at91: fix example for scl-gpios
  ARM: dts: at91: sama5d4: fix pinctrl muxing

Link: https://lore.kernel.org/r/20210611123446.20510-1-nicolas.ferre@microchip.comSigned-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'v5.13-next-dts64' of https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into arm/dt

mt8173:
- split hardware encoder block into two devices.

mt8167:
- add pm domains, multi-media system (mmsys), SMI, local arbiter
  (larb) and IOMMU nodes.

mt8183:
- Add new chromebooks: HP Chromebook 11a, Acer Chromebook 311, HP
  Chromebook x360 11MK G3 EE, Lenovo IdeaPad Flex 3.
- add power domain to SMI common node.
- add power supplies for EEPROM node.

* tag 'v5.13-next-dts64' of https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux: (21 commits)
  arm64: dts: mt8183: Add node for the Mali GPU
  arm64: dts: mt8183-kukui: Add tboard thermal zones
  arm64: dts: mt8183: add cbas node under cros_ec
  arm64: dts: mt8183: add supply name for eeprom
  arm64: dts: mt8183: remove syscon from smi_common node
  arm64: dts: mt8183: Add kukui-jacuzzi-fennel board
  arm64: dts: mt8183: Add kukui-jacuzzi-kenzo board
  arm64: dts: mt8183: Add kukui-jacuzzi-burnet board
  arm64: dts: mt8183: Add kukui-jacuzzi-willow board
  arm64: dts: mt8183: Add kukui-jacuzzi-kappa board
  dt-bindings: arm64: dts: mediatek: Add mt8183-kukui-jacuzzi-fennel
  dt-bindings: arm64: dts: mediatek: Add mt8183-kukui-jacuzzi-kenzo
  dt-bindings: arm64: dts: mediatek: Add mt8183-kukui-jacuzzi-burnet
  dt-bindings: arm64: dts: mediatek: Add mt8183-kukui-jacuzzi-willow
  dt-bindings: arm64: dts: mediatek: Add mt8183-kukui-jacuzzi-kappa
  arm64: dts: mediatek: mt8167: add iommu node
  arm64: dts: mediatek: mt8167: add larb nodes
  arm64: dts: mediatek: mt8167: add smi_common node
  arm64: dts: mediatek: mt8167: add mmsys node
  arm64: dts: mediatek: mt8167: add power domains
  ...

Link: https://lore.kernel.org/r/117d5eb5-bc99-70bb-a1a9-d7141fe96527@gmail.comSigned-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'renesas-dt-bindings-for-v5.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt

Renesas DT binding updates for v5.14

  - Document support for the new RZ/G2L, RZ/G2LC, and RZ/G2UL SoCs,
  - Document support for the new RZ/G2L SMARC EVK board.

* tag 'renesas-dt-bindings-for-v5.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
  dt-bindings: power: renesas,rzg2l-sysc: Add DT binding documentation for SYSC controller
  dt-bindings: arm: renesas: Document SMARC EVK
  dt-bindings: arm: renesas: Document Renesas RZ/G2{L,LC} SoC variants
  dt-bindings: arm: renesas: Document Renesas RZ/G2UL SoC

Link: https://lore.kernel.org/r/cover.1623403802.git.geert+renesas@glider.beSigned-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'renesas-arm-dt-for-v5.14-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt

Renesas ARM DT updates for v5.14 (take two)

  - External interrupt (INTC-EX) support for the R-Car M3-W+ SoC,
  - Initial support for the new RZ/G2L SoC on the RZ/G2L SMARC EVK
    board,
  - Miscellaneous fixes and improvements.

* tag 'renesas-arm-dt-for-v5.14-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
  arm64: dts: renesas: r9a07g044: Add SYSC node
  arm64: dts: renesas: Add initial device tree for RZ/G2L SMARC EVK
  arm64: dts: renesas: Add initial DTSI for RZ/G2{L,LC} SoC's
  dt-bindings: clock: Add r9a07g044 CPG Clock Definitions
  arm64: dts: renesas: r8a779a0: Drop power-domains property from GIC node
  arm64: dts: renesas: r8a77961: Add INTC-EX device node
  ARM: dts: silk: Configure pull-up for SOFT_SW GPIO keys
  ARM: dts: gose: Configure pull-up for SOFT_SW GPIO keys
  ARM: dts: blanche: Configure pull-up for SOFT_SW and SW25 GPIO keys
  ARM: dts: lager: Configure pull-up for SOFT_SW GPIO keys
  arm64: dts: renesas: r8a7796[01]: Fix OPP table entry voltages
  arm64: dts: renesas: Add missing opp-suspend properties

Link: https://lore.kernel.org/r/cover.1623403796.git.geert+renesas@glider.beSigned-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'juno-fix-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/dt

ARMv8 Juno fix for v5.14

Just a single fix to use standard and generic nodes names for SCMI
power domain controller and clock controller devicetree nodes.

* tag 'juno-fix-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
  arm64: dts: juno: Update SCPI nodes as per the YAML schema

Link: https://lore.kernel.org/r/20210611075805.2813712-1-sudeep.holla@arm.comSigned-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'ux500-dts-v5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into arm/dt

Some Ux500 DTS updates for v5.14:
- Fix interrupt cells, GPIO controller node names in accordance
  with new YAML schemas.
- Add proper compatible strings for Broadcomm Wifi and BT.
- Fix upp and add some mount matrices for accelerometers so
  e.g. UI:s work as they should.
- Drop the DRDY pin assignment for a non-existing pin on a
  magnetometer.

* tag 'ux500-dts-v5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
  ARM: dts: ux500: Fix orientation of Janice accelerometer
  ARM: dts: href: Mount matrices for TVK R2
  ARM: dts: ux500: Fix some compatible strings
  ARM: dts: ux500: Drop drdy pin assignment from magnetometer
  ARM: dts: ux500: Fix orientation of accelerometer
  ARM: dts: ux500: Rename gpio-controller node
  ARM: dts: ux500: Fix interrupt cells

Link: https://lore.kernel.org/r/CACRpkdYh9kZJU6PAxghPRGBco_61wRZgUnTZr_3qvySPCo5rBw@mail.gmail.comSigned-off-by: Olof Johansson <olof@lixom.net>

This pull request contains Broadcom ARM64-based SoCs changes for 5.14,
please pull the following:

- Zhen fixes the Broadcom stingray serial node unit names to fix a DT
  binding warning

* tag 'arm-soc/for-5.14/devicetree-arm64' of https://github.com/Broadcom/stblinux:
  arm64: dts: broadcom: normalize the node name of the UART devices

Link: https://lore.kernel.org/r/20210610194836.309869-2-f.fainelli@gmail.comSigned-off-by: Olof Johansson <olof@lixom.net>

This pull request contains Broadcom ARM-based SoCs Device Tree changes
for 5.14, please pull the following:

- Rafal updates the BCM5301x, HR2, BCM63xx, BCM5301x, NSP and Cygnus DTS
  files to resolve a number of DT binding check warnings pertaining to
  NAND, pinmux, clocks, SPI

- Stefan provides a fix for an increase in the DWC2 controller's RX FIFO
  causing regressions on the Raspberry Pi 4B

- Mateusz adds a BCM2711 specific VEC compatible string to allow keying
  off that variant properly

- Stefan adds support for the Raspberry Pi 400 by doing some DTS/DTSI
  re-organization work and finally adding the DTS file proper

* tag 'arm-soc/for-5.14/devicetree' of https://github.com/Broadcom/stblinux:
  arm64: dts: broadcom: Add reference to RPi 400
  ARM: dts: Add Raspberry Pi 400 support
  ARM: dts: bcm283x: Fix up GPIO LED node names
  dt-bindings: arm: bcm2835: Add Raspberry Pi 400 to DT schema
  ARM: dts: Move BCM2711 RPi specific into separate dtsi
  ARM: dts: bcm283x: Fix up MMC node names
  ARM: boot: dts: bcm2711: Add BCM2711 VEC compatible
  Revert "ARM: dts: bcm283x: increase dwc2's RX FIFO size"
  ARM: dts: BCM5301X: Fixup SPI binding
  dt-bindings: clock: brcm, iproc-clocks: convert to the json-schema
  ARM: dts: BCM5301X: Fix pinmux subnodes names
  ARM: dts: Hurricane 2: Fix NAND nodes names
  ARM: dts: BCM63xx: Fix NAND nodes names
  ARM: NSP: dts: fix NAND nodes names
  ARM: Cygnus: dts: fix NAND nodes names
  ARM: brcmstb: dts: fix NAND nodes names
  ARM: dts: BCM5301X: Fix NAND nodes names

Link: https://lore.kernel.org/r/20210610194836.309869-1-f.fainelli@gmail.comSigned-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'stm32-dt-for-v5.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/dt

STM32 DT updates for v5.14, round 1

Highlights:
-----------

MCU part:
 - Fixes for Yaml verifications

MPU part:
 - Configure qspi's mdma transfer to block for stm32mp151

 - ST boards:
  - Fixes for yaml verifications

 - DH boards:
  - Fixes for yaml verifications
  - Rework of LAN8710i on DHCOM SoM to fit with requested reset sequence.

 - Odyssey boards:
  - fix Sd card detectection (gpio line updated)
  - fix eMMC VQMMC suuply (use vdd instead of v3v3)

* tag 'stm32-dt-for-v5.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
  ARM: dts: stm32: fix stpmic node for stm32mp1 boards
  ARM: dts: stm32: Rename spi-flash/mx66l51235l@N to flash@N on DHCOM SoM
  ARM: dts: stm32: Rename eth@N to ethernet@N on DHCOM SoM
  ARM: dts: stm32: Drop unused linux,wakeup from touchscreen node on DHCOM SoM
  ARM: dts: stm32: fix the Odyssey SoM eMMC VQMMC supply
  ARM: dts: stm32: add a new DCMI pins group on stm32mp15
  ARM: dts: stm32: fix ltdc pinctrl on microdev2.0-of7
  dt-bindings: net: document ptp_ref clk in dwmac
  ARM: dts: stm32: move stmmac axi config in ethernet node on stm32mp15
  ARM: dts: stm32: fix i2c node name on stm32f746 to prevent warnings
  ARM: dts: stm32: update pinctrl node name on STM32 MCU to prevent warnings
  ARM: dts: stm32: fix timer nodes on STM32 MCU to prevent warnings
  ARM: dts: stm32: fix RCC node name on stm32f429 MCU
  ARM: dts: stm32: fix gpio-keys node on STM32 MCU boards
  ARM: dts: stm32: fix stm32mp157c-odyssey card detect pin
  ARM: dts: stm32: Configure qspi's mdma transfer to block for stm32mp151
  ARM: dts: stm32: Fix touchscreen node on dhcom-pdk2
  ARM: dts: stm32: Remove extra size-cells on dhcom-pdk2
  ARM: dts: stm32: Rework LAN8710Ai PHY reset on DHCOM SoM

Link: https://lore.kernel.org/r/e4bfb255-63fb-74a8-d591-eb09821c93ee@foss.st.comSigned-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'samsung-dt-5.14' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt

Samsung DTS ARM changes for v5.14

1. Several cleanups and alignment with dtschema.  This includes removal
   of unused properties and fixing LED brightness property.
2. Enable PMIC RTC interrupt as a wakeup source (intended to wakeup for
   example from Suspend to RAM where the PMIC RTC's power is still
   supplied).
3. Disable unused/not implemented camera on GT-I9100.

* tag 'samsung-dt-5.14' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
  ARM: dts: exynos: Disable unused camera input for I9100
  ARM: dts: exynos: enable PMIC wakeup from suspend on Odroid XU3/XU4 family
  ARM: dts: exynos: enable PMIC wakeup from suspend on SMDK5420
  ARM: dts: exynos: enable PMIC wakeup from suspend on Arndale Octa
  ARM: dts: exynos: enable PMIC wakeup from suspend on P4 Note
  ARM: dts: exynos: enable PMIC wakeup from suspend on Odroid X/U3
  ARM: dts: exynos: enable PMIC wakeup from suspend on Midas
  ARM: dts: exynos: enable PMIC wakeup from suspend on Odroid XU
  ARM: dts: exynos: enable PMIC wakeup from suspend on Arndale
  ARM: dts: exynos: enable PMIC wakeup from suspend on Origen4412
  ARM: dts: exynos: enable PMIC wakeup from suspend on Itop Core
  ARM: dts: s5pv210: remove unused Atmel touchscreen properties in Goni
  ARM: dts: exynos: fix PWM LED max brightness on Odroid XU4
  ARM: dts: exynos: fix PWM LED max brightness on Odroid HC1
  ARM: dts: exynos: fix PWM LED max brightness on Odroid XU/XU3
  ARM: dts: exynos: replace legacy MMS114 touchscreen x/y properties in GT-N7100
  ARM: dts: exynos: align Broadcom WiFi with dtschema

Link: https://lore.kernel.org/r/20210610074055.12474-1-krzysztof.kozlowski@canonical.comSigned-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'aspeed-5.14-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/bmc into arm/dt

ASPEED device tree updates for 5.14

 - IBM Rainier and Everest LED descriptions. These systems have a large
   number of LEDs attached via expanders.

 - Ampere Mt Jade updates, as OpenBMC bringup continues for this
   machine.

 - Updated 64MB flash layout for systems using OpenBMC on NOR root file
   systems.

 - Support for HS200 MMC on AST2600 EVB. This is only supported from A2,
   so a new device tree is added to support A0 and A1.

 - Update all command lines for early serial output.

* tag 'aspeed-5.14-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/bmc:
  ARM: dts: aspeed: everest: Add pcie cable card indicator leds
  ARM: dts: aspeed: everest: Add vrm and other indicator leds
  ARM: dts: aspeed: everest: Add dimm indicator leds
  ARM: dts: aspeed: everest: Add pcie slot indicator leds
  ARM: dts: aspeed: everest: Add nvme and fan indicator leds
  ARM: dts: aspeed: everest: Add system level indicator leds
  ARM: dts: aspeed-g5: Add SCU phandle to GFX node
  ARM: dts: aspeed: Everest: Add directly controlled LEDs
  ARM: dts: aspeed: Rainier 4U: Remove fan updates
  ARM: dts: aspeed: Everest: Fix cable card PCA chips
  ARM: dts: aspeed: Grow u-boot partition 64MiB OpenBMC flash layout
  ARM: dts: aspeed: mtjade: switch to 64MB flash layout
  ARM: dts: aspeed: mtjade: Add PSU support
  ARM: dts: aspeed: mtjade: Enable OCP card support via NC-SI
  ARM: dts: aspeed: Set earlycon boot argument
  ARM: dts: aspeed-g6: Add pinctrl settings
  ARM: dts: aspeed: ast2600evb: Add dts file for A1 and A0
  ARM: dts: aspeed: ast2600evb: Add phase correction for emmc controller.
  ARM: dts: aspeed: ast2600evb: Add sdhci node and gpio regulator for A2 evb.

Link: https://lore.kernel.org/r/CACPK8XduV9F=piu1qh56g+YNOZOBYTW7b2Y=XVYafpYDwWmDYA@mail.gmail.comSigned-off-by: Olof Johansson <olof@lixom.net>

Add the crypto engine as a child of the NPE.

Link: https://lore.kernel.org/r/20210605161007.3397216-1-linus.walleij@linaro.org
Cc: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'amlogic-arm64-dt-for-v5.14' of https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux into arm/dt

Amlogic ARM64 DT changed for v5.14:
- set 128bytes FIFO size on uart A
- add Banana PI BPI-M5 board dts & bindings
- meson-sm1: add toacodec node to use internal audio DAC
- enable hdmi audio loopback on VIM3 board

* tag 'amlogic-arm64-dt-for-v5.14' of https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux:
  arm64: dts: meson: set 128bytes FIFO size on uart A
  arm64: dts: meson-sm1: add Banana PI BPI-M5 board dts
  dt-bindings: arm: amlogic: add Banana PI M5 bindings
  arm64: dts: meson-sm1: add toacodec node
  arm64: dts: meson: vim3: enable hdmi audio loopback

Link: https://lore.kernel.org/r/bb207cf8-fc7a-3121-eea8-56618b5952aa@baylibre.comSigned-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'omap-for-v5.14/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt

Devicetree changes for omaps for v5.14 merge window

Mostly just clean-up for device tree binding checks with
few other clean-up patches:

- Drop ov5640 sensor for dra76-evm, it's just one of the
  optional additional sensors and makes hard to use any of
  the other options, TI is using the devicetree overlay
  snippets for these

- Group the phandles in osd3358-sm-red to make the files
  more readable

- A series of gpio clean-up patches to follow the binding
  documentation

- Move ti,no-reset related properties to the target module
  level, the ti-sysc driver handles them also in the child
  but they really belong to the target module

- Drop the unnecessary uart compatible entries to make the
  binding check to work

- Mailbox related updates to make the binding check to
  work

* tag 'omap-for-v5.14/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: OMAP2+: Replace underscores in sub-mailbox node names
  ARM: dts: AM33xx/AM43xx: Rename wkup_m3 sub-mailbox node
  ARM: dts: OMAP2/OMAP3: Rename processor sub-mailbox nodes
  ARM: dts: OMAP2420: Drop interrupt-names from mailbox node
  ARM: dts: am437x-l4: Drop ti,omap2-uart entry from UART nodes
  ARM: dts: dra7-l4: Drop ti,omap4-uart entry from UART nodes
  ARM: dts: am335x: fix ti,no-reset-on-init flag for gpios
  ARM: dts: am437x-gp-evm: fix ti,no-reset-on-init flag for gpios
  ARM: dts: am57xx-cl-som-am57x: fix ti,no-reset-on-init flag for gpios
  ARM: dts: dra7x-evm: Align GPIO hog names with dt-schema
  ARM: dts: omap5-board-common: align gpio hog names with dt-schema
  ARM: dts: omap3: align gpio hog names with dt-schema
  ARM: dts: am437x: align gpio hog names with dt-schema
  ARM: dts: am335x: align GPIO hog names with dt-schema
  ARM: dts: osd3358-sm-red: group in the same phandle all its properties
  ARM: dts: dra76-evm: remove ov5640

Link: https://lore.kernel.org/r/pull-1622618286-677305@atomide.com-3Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'renesas-arm-dt-for-v5.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt

Renesas ARM DT updates for v5.14

  - GPIO extender support for the Falcon development board,
  - Switches support for the ALT development board,
  - Miscellaneous fixes and improvements.

* tag 'renesas-arm-dt-for-v5.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
  ARM: dts: alt: Add SW2 as GPIO keys
  ARM: dts: renesas: Move enable-method to CPU nodes
  arm64: dts: renesas: beacon: Fix USB ref clock references
  arm64: dts: renesas: beacon: Fix USB extal reference
  ARM: dts: rcar-gen1: Correct internal delay for i2c[123]
  arm64: dts: renesas: eagle: Add x1 clock
  ARM: dts: koelsch: Rename sw2 to keyboard
  ARM: dts: r8a7779, marzen: Fix DU clock names
  arm64: dts: renesas: v3msk: Fix memory size
  arm64: dts: renesas: condor: Switch eMMC bus to 1V8
  arm64: dts: renesas: falcon-csi-dsi: Add GPIO extenders
  arm64: dts: renesas: beacon kit: Setup AVB refclk
  arm64: dts: renesas: Add fck to etheravb-rcar-gen3 clock-names list
  ARM: dts: renesas: Add fck to etheravb-rcar-gen2 clock-names list

Link: https://lore.kernel.org/r/cover.1622188835.git.geert+renesas@glider.beSigned-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'gemini-dts-v5.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into arm/dt

Gemini device tree updates for the v5.14 kernel:
- MAINTAINERS fix for the DTS files
- Drop a duplicate ethernet node on the RUT1xx DTS
- Add device_type to the PCI node
- Fix up some DTS syntax so it agrees with the schemas merged
  for the v5.14 merge window

* tag 'gemini-dts-v5.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
  ARM: dts: gemini: remove xxx-cells from display
  ARM: dts: gemini-dlink-dir-685: Remove address from display port
  ARM: dts: gemini-dlink-dir-685: rename gpio-i2c to i2c
  ARM: dts: gemini-dlink-dns-313: rename gpio-i2c to i2c
  ARM: dts: gemini: convert obsolete SPI properties
  ARM: dts: gemini: use the right rtc compatible
  ARM: dts: gemini: add device_type on pci
  ARM: dts: gemini-rut1xx: remove duplicate ethernet node
  ARM: dts: gemini: rename mdio to the right name
  MAINTAINERS: gemini: add missing dts pattern

Link: https://lore.kernel.org/r/CACRpkdZWpLAcAStq8dEyGL_d9Bvp-WNPu-2EuJw1eTL4kyvgig@mail.gmail.comSigned-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'ixp4xx-dts-v5.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into arm/dt

IXP4xx DTS updates for the v5.14 kernel:
- Add ethernet to the boards
- Add PCI hosts to the boards
- Create an expansion bus around the flash memory
- Add the beeper to NSLU2 completing the NSLU2 DTS

* tag 'ixp4xx-dts-v5.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
  ARM: dts: Fix up the IXP4xx ethernet nodes
  ARM: dts: ixp4xx: Add beeper to the NSLU2
  ARM: dts: ixp4xx: Create a proper expansion bus
  ARM: dts: ixp4xx: Add PCI hosts
  ARM: dts: ixp4xx: Add ethernet

Link: https://lore.kernel.org/r/CACRpkdbmRjGW7vpr7hG+jiRTqNMZAyKZNhtvzj=SqhZmb1+F6A@mail.gmail.comSigned-off-by: Olof Johansson <olof@lixom.net>

This patch adds devicetree for intel-ixp42x-welltech-epbx100.

Link: https://lore.kernel.org/r/20210504193457.4008384-6-clabbe@baylibre.comSigned-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Adds welltech,epbx100 as a valid intel-ixp4xx board.

Link: https://lore.kernel.org/r/20210504193457.4008384-5-clabbe@baylibre.comSigned-off-by: Corentin Labbe <clabbe@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Add vendor prefix for Welltech computer Co Ld.

Link: https://lore.kernel.org/r/20210504193457.4008384-4-clabbe@baylibre.comSigned-off-by: Corentin Labbe <clabbe@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Document the compatible for GE B1x5pv2 boards.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Document binding for congatec.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This adds device tree files for the General Electric Healthcare
(GEHC) B1x5v2 series. All models make use of Congatec's QMX6
system on module, which is described in its own device tree include,
so that it can also be used by other boards.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add VIO regulator that supplies multiple ethernet magnetics and
currently there is no upstream support for that in the networking,
so just keep the regulator enabled always to emulate what other
boards, which have this hard-wired, do. Until there is support.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add aliases for i2c and serial to match the order of the DHCOM
standard [1]. Also add aliases for the two rtcs. The i2c rtc
is the primary one.

[1] https://wiki.dh-electronics.com/images/2/2e/DOC_DHCOM-Standard-Specification_R01_2016-11-17.pdfSigned-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The i2c bus can freeze at the end of transaction so the bus can no longer work.
This scenario is improved by adding scl/sda gpios definitions to implement the
i2c bus recovery mechanism.

Fixes: 52c7a088 ("ARM: dts: imx6q: Add support for the DHCOM iMX6 SoM and PDK2")
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

To make the ethernet cable plugin detection reliable the
power detection of the smsc phy has been disabled.

Fixes: 52c7a088 ("ARM: dts: imx6q: Add support for the DHCOM iMX6 SoM and PDK2")
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Fix ethernet reset time properties as described in
Documentation/devicetree/bindings/net/ethernet-phy.yaml

Fixes: 52c7a088 ("ARM: dts: imx6q: Add support for the DHCOM iMX6 SoM and PDK2")
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

On some STM32 MP15 boards, stpmic node is not correct which generates
warnings running "make dtbs_check W=1" command. Issues are:

-"regulator-active-discharge" is not a boolean but an uint32.
-"regulator-over-current-protection" is not a valid entry for vref_ddr.
-LDO4 has a fixed voltage (3v3) so min/max entries are not allowed.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Fix the following dtbs_check warning:
spi-flash@0: $nodename:0: 'spi-flash@0' does not match '^flash(@.*)?$'
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: kernel@dh-electronics.com
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Fix the following dtbs_check warning:
eth@1,0: $nodename:0: 'eth@1,0' does not match '^ethernet(@.*)?$'
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: kernel@dh-electronics.com
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Fix the following dtbs_check warning:
touchscreen@38: 'linux,wakeup' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: kernel@dh-electronics.com
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

The Seeed SoM-STM32MP157C device tree had the eMMC’s (SDMMC2) VQMMC
supply set to v3v3 (buck4), the same as the VMMC supply. That was
incorrect, as on the SoM, the VQMMC supply is provided from vdd (buck3)
instead.
Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Add SYSC node to RZ/G2L (R9A07G044) SoC .dtsi.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210609163717.3083-4-prabhakar.mahadev-lad.rj@bp.renesas.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Add basic support for RZ/G2L SMARC EVK (based on R9A07G044L2):
- memory
- External input clock
- SCIF
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210609153230.6967-12-prabhakar.mahadev-lad.rj@bp.renesas.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>