At imx7ulp, the USB related analog register is located in PHY register
region too, so we need to control PLL at PHY driver directly.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add compatible for 7ulp USB PHY.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Controller for OUT endpoints has shared on-chip buffers for all incoming
packets, including ep0out. It's FIFO buffer, so packets must be handled
by DMA in correct order. If the first packet in the buffer will not be
handled, then the following packets directed for other endpoints and
functions will be blocked.

Additionally the packets directed to one endpoint can block entire on-chip
buffers. In this case transfer to other endpoints also will blocked.

To resolve this issue after raising the descriptor missing interrupt
driver prepares internal usb_request object and use it to arm DMA
transfer.

The problematic situation was observed in case when endpoint has
been enabled but no usb_request were queued. Driver try detects
such endpoints and will use this workaround only for these endpoint.

Driver use limited number of buffer. This number can be set by macro
CDNS_WA2_NUM_BUFFERS.

Such blocking situation was observed on ACM gadget. For this function
host send OUT data packet but ACM function is not prepared for
this packet. It's cause that buffer placed in on chip memory block
transfer to other endpoints.

Issue has been fixed for DEV_VER_V2 version of controller.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch introduce new Cadence USBSS DRD driver to Linux kernel.

The Cadence USBSS DRD Controller is a highly configurable IP Core which
can be instantiated as Dual-Role Device (DRD), Peripheral Only and
Host Only (XHCI)configurations.

The current driver has been validated with FPGA platform. We have
support for PCIe bus, which is used on FPGA prototyping.

The host side of USBSS-DRD controller is compliant with XHCI
specification, so it works with standard XHCI Linux driver.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Patch moves switch responsible for decoding descriptor type
outside snprintf. It improves code readability a little.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Patch adds usb_decode_test_mode and usb_decode_device_feature functions,
which allow to make more readable and simplify the
usb_decode_set_clear_feature function.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Patch moves some decoding functions from driver/usb/dwc3/debug.h driver
to driver/usb/gadget/debug.c file. These moved functions include:
    dwc3_decode_get_status
    dwc3_decode_set_clear_feature
    dwc3_decode_set_address
    dwc3_decode_get_set_descriptor
    dwc3_decode_get_configuration
    dwc3_decode_set_configuration
    dwc3_decode_get_intf
    dwc3_decode_set_intf
    dwc3_decode_synch_frame
    dwc3_decode_set_sel
    dwc3_decode_set_isoch_delay
    dwc3_decode_ctrl

These functions are used also in inroduced cdns3 driver.

All functions prefixes were changed from dwc3 to usb.
Also, function's parameters has been extended according to the name
of fields in standard SETUP packet.
Additionally, patch adds usb_decode_ctrl function to
include/linux/usb/gadget.h file.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch aim at documenting USB related dt-bindings for the
Cadence USBSS-DRD controller.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch adds the necessary PCI ID for TGP-LP devices.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The member @lock of dwc3_ep struct is only initialized,
and not used elsewhere, so remove it.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch simply adds a new PCI Device ID
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

snprintf returns the actual length of the buffer created; however,
this is not the case if snprintf truncates its parameter.
See https://lwn.net/Articles/69419/ for a detailed explanation.
The current code correctly handles this case at the expense
of extra code in the return statement.

scnprintf does returns the actual length of the buffer created
making the ?: operator unnecessary in the return
statement.

This change does not alter the functionality of the code.
Signed-off-by: Daniel M German <dmg@turingmachine.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

On spin lock release in rx_submit, gether_disconnect get a chance to
run, it makes port_usb NULL, rx_submit access NULL port USB, hence null
pointer crash.

Fixed by releasing the lock in rx_submit after port_usb is used.

Fixes: 2b3d942c ("usb ethernet gadget: split out network core")
Cc: <stable@vger.kernel.org>
Signed-off-by: Kiruthika Varadarajan <Kiruthika.Varadarajan@harman.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This change is to fix below warning message in following scenario:
usb_composite_setup_continue: Unexpected call

When system tried to enter suspend, the fsg_disable() will be called to
disable fsg driver and send a signal to fsg_main_thread. However, at
this point, the fsg_main_thread has already been frozen and can not
respond to this signal. So, this signal will be pended until
fsg_main_thread wakes up.

Once system resumes from suspend, fsg_main_thread will detect a signal
pended and do some corresponding action (in handle_exception()). Then,
host will send some setup requests (get descriptor, set configuration...)
to UDC driver trying to enumerate this device. During the handling of "set
configuration" request, it will try to sync up with fsg_main_thread by
sending a signal (which is the same as the signal sent by fsg_disable)
to it. In a similar manner, once the fsg_main_thread receives this
signal, it will call handle_exception() to handle the request.

However, if the fsg_main_thread wakes up from suspend a little late and
"set configuration" request from Host arrives a little earlier,
fsg_main_thread might come across the request from "set configuration"
when it handles the signal from fsg_disable(). In this case, it will
handle this request as well. So, when fsg_main_thread tries to handle
the signal sent from "set configuration" later, there will nothing left
to do and warning message "Unexpected call" is printed.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: EJ Hsu <ejh@nvidia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Gadget applications may have a requirement to disable the U1 and U2
entry based on the usecase. Below are few usecases where the disabling
U1/U2 entries may be possible.

Usecase 1:
When combining dwc3 with an redriver for a USB Type-C device solution, it
sometimes have problems with leaving U1/U2 for certain hosts, resulting in
link training errors and reconnects. For this U1/U2 state entries may be
avoided.

Usecase 2:
When performing performance benchmarking on mass storage gadget the
U1 and U2 entries can be disabled.

Usecase 3:
When periodic transfers like ISOC transfers are used with bInterval
of 1 which doesn't require the link to enter into U1 or U2 state entry
(since ping is issued from host for every uframe interval). In this
case the U1 and U2 entry can be disabled.

Disablement of U1/U2 can be done by setting U1DevExitLat and U2DevExitLat
values to 0 in the BOS descriptor. Host on seeing 0 value for U1DevExitLat
and U2DevExitLat, it doesn't send SET_SEL requests to the gadget. There
may be some hosts which may send SET_SEL requests even after seeing 0 in
the UxDevExitLat of BOS descriptor. To aviod U1/U2 entries for these type
of hosts, dwc3 controller can be programmed to reject those U1/U2 requests
by not enabling ACCEPTUxENA bits in DCTL register.

This patch updates the same.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Claus H. Stovgaard <cst@phaseone.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Passing struct usb_gadget * as an extra argument in get_config_params
makes gadget drivers to easily update the U1DevExitLat & U2DevExitLat
values based on the values passed from the device tree. This patch
does the same
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch updates the documentation with the information related
to the quirks that needs to be added for disabling the link entering
into the U1 and U2 states
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Use of_clk_get_parent_count() instead of open coding.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The required clocks needs to be enabled before the first register
access. After commit fe8abf33 ("usb: dwc3: support clocks and resets
for DWC3 core"), this happens when the dwc3_core_is_valid function is
called, but the mentioned commit adds that call in the wrong place,
before the clocks are enabled. So, move that call after the
clk_bulk_enable() to ensure the clocks are enabled and the reset
deasserted.

I detected this while, as experiment, I tried to move the clocks and resets
from the glue layer to the DWC3 core on a Samsung Chromebook Plus.

That was not detected before because, in most cases, the glue layer
initializes SoC-specific things and then populates the child "snps,dwc3"
with those clocks already enabled.

Fixes: b873e2d0 ("usb: dwc3: Do core validation early on probe")
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

dwc3_qcom_clk_init() is called with of_count_phandle_with_args() as an
argument.  If of_count_phandle_with_args() returns an error, the number
of clocks will be a negative value and will lead to undefined behaviour.

Ensure we check for an error before attempting to blindly use the value.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

When booting with Device Tree, the current default boot configuration
table option, the request to boot via 'host mode' comes from the
'dr_mode' property.  A property of the same name can be used inside
ACPI tables too.  However it is missing from the SDM845's ACPI tables
so we have to supply this information using Platform Device Properties
instead.

This does not change the behaviour of any currently supported devices.
The property is only set on ACPI enabled platforms, thus for H/W
booting DT, unless a 'dr_mode' property is present, the default is
still OTG (On-The-Go) as per [0].  Any new ACPI devices added will
also be able to over-ride this implementation by providing a 'dr_mode'
property in their ACPI tables.  In cases where 'dr_mode' is omitted
from the tables AND 'host mode' should not be the default (very
unlikely), then we will have to add some way of choosing between them
at run time - most likely by ACPI HID.

[0] Documentation/devicetree/bindings/usb/generic.txt
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In Linux, the DWC3 core exists as its own independent platform device.
Thus when describing relationships in Device Tree, the current default
boot configuration table option, the DWC3 core often resides as a child
of the platform specific node.  Both of which are given their own
address space descriptions and the drivers can be mostly agnostic to
each other.

However, other Operating Systems have taken a more monolithic approach,
which is evident in the configuration ACPI tables for the Qualcomm
Snapdragon SDM850, where all DWC3 (core and platform) components are
described under a single IO memory region.

To ensure successful booting using the supplied ACPI tables, we need to
devise a way to chop up the address regions provided and subsequently
register the DWC3 core with the resultant information, which is
precisely what this patch aims to achieve.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

When booting with ACPI as the active set of configuration tables,
all; clocks, regulators, pin functions ect are expected to be at
their ideal values/levels/rates, thus the associated frameworks
are unavailable.  Ensure calls to these APIs are shielded when
ACPI is enabled.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This reverts commit b0d65902.

The reverted commit does nothing but adding two unnecessary lines
of code.  It sets a local variable to NULL in two functions, but
that variable is not used anywhere in the rest of those functions.
This is just confusing, so let's remove it.

Cc: Vardan Mikayelyan <mvardan@synopsys.com>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Douglas Anderson <dianders@chromiun.org>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The pointer 's' is being assigned however the pointer is
never used with either of these values before it it reassigned much
later on.  I suspect it was going to be used in the output of the
main control registers scnprintf but was omitted.  The assignments
of 's' to the driver name or the literal string are redundant and
can be removed.

Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In some cases the "Allocate & copy" block in ffs_epfile_io() is not
executed. Consequently, in such a case ffs_alloc_buffer() is never called
and struct ffs_io_data is not initialized properly. This in turn leads to
problems when ffs_free_buffer() is called at the end of ffs_epfile_io().

This patch uses kzalloc() instead of kmalloc() in the aio case and memset()
in non-aio case to properly initialize struct ffs_io_data.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

With the current implementation omap_udc_stop is always
returning -ENODEV.

Added changes to return 0 and remove variable status.

Issue identified with coccicheck
drivers/usb/gadget/udc/omap_udc.c:2106:6-12:
Unneeded variable: "status". Return "- ENODEV" on line 2128
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch fixes below warning reported by coccicheck

drivers/usb/gadget/udc/fotg210-udc.c:484:5-8: Unneeded variable: "ret".
Return "0" on line 507
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

at91_wakeup is always returning -EINVAL.

But usb_gadget_wakeup expects 0 on success and negative number on
failure. As per current implementation this function wont fail.

This patch removes unneeded variable and returns 0.

Issue identified by coccicheck

drivers/usb/gadget/udc/at91_udc.c:802:6-12:
Unneeded variable: "status". Return "- EINVAL" on line 821
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The RZ/G2E cat874 board has a type-c connector connected to hd3ss3220 usb
type-c drp port controller. Enhance role switch support to assign the role
requested by connector device using the usb role switch class framework.
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Fixed a coding style issue, replacing unsigned with unsigned int.
Reviewed-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Jonas Stenvall <jonas.stenvall.umea@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The following line of code in function ffs_epfile_io is trying to set
flag io_data->use_sg in case buffer required is larger than one page.

    io_data->use_sg = gadget->sg_supported && data_len > PAGE_SIZE;

However at this point of time the variable data_len has not been set
to the proper buffer size yet. The consequence is that io_data->use_sg
is always set regardless what buffer size really is, because the condition
(data_len > PAGE_SIZE) is effectively an unsigned comparison between
-EINVAL and PAGE_SIZE which would always result in TRUE.

Fixes: 772a7a72 ("usb: gadget: f_fs: Allow scatter-gather buffers")
Signed-off-by: Fei Yang <fei.yang@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

If the 'snps,need-phy-for-wake' is set in the device tree then:

- We know that we can wakeup, so call device_set_wakeup_capable().
  The USB core will use this knowledge to enable wakeup by default.
- We know that we should keep the PHY on during suspend if something
  on our root hub needs remote wakeup.  This requires the patch (USB:
  Export usb_wakeup_enabled_descendants()).  Note that we don't keep
  the PHY on at suspend time if it's not needed because it would be a
  power draw.

If we later find some users of dwc2 that can support wakeup without
keeping the PHY on we may want to add a way to call
device_set_wakeup_capable() without keeping the PHY on at suspend
time.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

We want to be able to wake from USB if a device is plugged in that
wants remote wakeup.  Enable it on both dwc2 controllers.

NOTE: this is added specifically to veyron and not to rk3288 in
general since it's not known whether all rk3288 boards are designed to
support USB wakeup.  It is plausible that some boards could shut down
important rails in S3.

Also note that currently wakeup doesn't seem to happen unless you use
the "deep" suspend mode (where SDRAM is turned off).  Presumably the
shallow suspend mode is gating some sort of clock that's important but
I couldn't easily figure out how to get it working.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Some SoCs with a dwc2 USB controller may need to keep the PHY on to
support remote wakeup.  Allow specifying this as a device tree
property.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Samsung Exynos SoCs require to force UTMI width to 8bit, otherwise the
host side of the shared USB2 PHY doesn't work.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Fixes: 707d80f0 ("usb: dwc2: gadget: Replace phyif with phy_utmi_width")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add support for the OTG ID change interrupt to switch between Host
and Device mode.

Tested on the Hardkernel Odroid-N2 board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

For consistency with the naming of (most) other documentation files for DT
bindings for Renesas IP blocks rename the Renesas USB3.0 peripheral
documentation file from renesas-gen3.txt to renesas,gen3.txt.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

For consistency with the naming of (most) other documentation files for DT
bindings for Renesas IP blocks rename the Renesas USBHS documentation file
from renesas-usbhs.txt to renesas,usbhs.txt.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>