- 04 Mar, 2022 40 commits
-
-
Luiz Augusto von Dentz authored
This fixes attemting to print hdev->name directly which causes them to print an error: kernel: read_version:367: (efault): sock 000000006a3008f2 Signed-off-by:
Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org>
-
Sean Wang authored
There is a conflict between MediaTek wmt event and msft vendor extension logic in the core layer since 145373cb ("Bluetooth: Add framework for Microsoft vendor extension") was introduced because we changed the type of mediatek wmt event to the type of msft vendor event in the driver. But the purpose we reported mediatek event to the core layer is for the diagnostic purpose with that we are able to see the full packet trace via monitoring socket with btmon. Thus, it is harmless we keep the original type of mediatek vendor event here to avoid breaking the msft extension function especially they can be supported by Mediatek chipset like MT7921 , MT7922 devices and future devices. Signed-off-by:
Sean Wang <sean.wang@mediatek.com> Signed-off-by:
-
Chih-Ying Chiang authored
Implement .cmd_timeout to reset the MT7921s device via a dedicated GPIO pin when the firmware hang or the command has no response. Co-developed-by:
Mark Chen <mark-yw.chen@mediatek.com> Signed-off-by:
Chih-Ying Chiang <chih-yin.chiang@mediatek.com> Signed-off-by:
-
Colin Ian King authored
Don't populate the read-only array bt_uuid_any on the stack but instead make it static const. Also makes the object code a little smaller. Signed-off-by:
Colin Ian King <colin.i.king@gmail.com> Signed-off-by:
-
Christophe JAILLET authored
'peer_addr' is a structure embedded in 'struct lowpan_peer'. So there is no need to explicitly call memset(0) on it. It is already zeroed by kzalloc() when 'peer' is allocated. Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
-
Zijun Hu authored
WCN6855 2.1 will reset to apply firmware downloaded, so wait a moment for reset done then go ahead to improve stability. Signed-off-by:
Zijun Hu <quic_zijuhu@quicinc.com> Signed-off-by:
-
Piotr Dymacz authored
The LG LGSBWAC02 (FCC ID: BEJLGSBWAC02) is a combo Wi-Fi/BT module which can be found in several different LG TV models. This module is based on already supported MediaTek MT7663U series. Device from /sys/kernel/debug/usb/devices: T: Bus=01 Lev=02 Prnt=02 Port=03 Cnt=02 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=043e ProdID=310c Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=a0 MxPwr=100mA A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 8 Cls=ff(vend.) Sub=ff Prot=ff Driver=mt7663u E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=08(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms Signed-off-by:
Piotr Dymacz <pepe2k@gmail.com> Signed-off-by:
-
Kiran K authored
$ lsusb Bus 003 Device 003: ID 8087:0035 Intel Corp. $ cat /sys/kernel/debug/usb/devices T: Bus=03 Lev=01 Prnt=01 Port=09 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=8087 ProdID=0035 Rev= 0.00 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms Signed-off-by:
Kiran K <kiran.k@intel.com> Signed-off-by:
-
Radoslaw Biernacki authored
This patch introduce eir_skb_put_data() that can be used to simplify operations on eir in goal of eliminating the necessity of intermediary buffers. eir_skb_put_data() is in pair to what eir_append_data() does with help of eir_len, but without awkwardness when passing return value to skb_put() (as it returns updated offset not size). Signed-off-by:
Radoslaw Biernacki <rad@semihalf.com> Signed-off-by:
-
Radoslaw Biernacki authored
This patch fixes skb allocation, as lack of space for ev might push skb tail beyond its end. Also introduce eir_precalc_len() that can be used instead of magic numbers for similar eir operations on skb. Fixes: cf1bce1d ("Bluetooth: mgmt: Make use of mgmt_send_event_skb in MGMT_EV_DEVICE_FOUND") Fixes: e9674143 ("Bluetooth: mgmt: Make use of mgmt_send_event_skb in MGMT_EV_DEVICE_CONNECTED") Signed-off-by:
Angela Czubak <acz@semihalf.com> Signed-off-by:
Marek Maslanka <mm@semihalf.com> Signed-off-by:
-
Minghao Chi authored
Return value from mgmt_cmd_complete() directly instead of taking this in another redundant variable. Reported-by:
Zeal Robot <zealci@zte.com.cn> Signed-off-by:
Minghao Chi <chi.minghao@zte.com.cn> Signed-off-by:
CGEL ZTE <cgel.zte@gmail.com> Signed-off-by:
-
Tom Rix authored
clang static analysis reports this problem hci_sync.c:4428:2: warning: Undefined or garbage value returned to caller return err; ^~~~~~~~~~ If there are no connections this function is a noop but err is never set and a false error could be reported. Return 0 as other hci_* functions do. Fixes: 182ee45d ("Bluetooth: hci_sync: Rework hci_suspend_notifier") Signed-off-by:Tom Rix <trix@redhat.com> Signed-off-by:
-
Changcheng Deng authored
There is a regular need in the kernel to provide a way to declare having a dynamically sized set of trailing elements in a structure. Kernel code should always use "flexible array members" for these cases. The older style of one-element or zero-length arrays should no longer be used. Reference: https://www.kernel.org/doc/html/latest/process/deprecated.html#zero-length-and-one-element-arraysReported-by:
Changcheng Deng <deng.changcheng@zte.com.cn> Signed-off-by:
-
Jiapeng Chong authored
Since the starting value in the for loop is greater than or equal to 1, the restriction is CAS_FLAG_REG_PLUS is in the file cassini.h is defined as 0x1 by macro, and the for loop and if condition is not satisfied, so the code here is redundant. Clean up the following smatch warning: drivers/net/ethernet/sun/cassini.c:3513 cas_start_dma() warn: we never enter this loop. drivers/net/ethernet/sun/cassini.c:1239 cas_init_rx_dma() warn: we never enter this loop. drivers/net/ethernet/sun/cassini.c:1247 cas_init_rx_dma() warn: we never enter this loop. Reported-by:
Abaci Robot <abaci@linux.alibaba.com> Signed-off-by:
Jiapeng Chong <jiapeng.chong@linux.alibaba.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Simon Horman says: ==================== Add AF_XDP zero-copy support for NFP Niklas Söderlund says: This series adds AF_XDP zero-copy support for the NFP driver. The series is based on previous work done by Jakub Kicinski. Patch 1/5 and 2/5 prepares the driver for AF_XDP support by refactoring functions that will act differently once AF_XDP is active or not making the driver easier to read and by preparing some functions to be reused outside the local file scope. Patch 3/5 and 4/5 prepares the driver for dealing the UMEM while finally patch 5/5 adds AF_XDP support. Based on work by Jakub Kicinski. ==================== Signed-off-by: -
Niklas Söderlund authored
This patch adds zero-copy Rx and Tx support for AF_XDP sockets. It do so by adding a separate NAPI poll function that is attached to a each channel when the XSK socket is attached with XDP_SETUP_XSK_POOL, and restored when the XSK socket is terminated, this is done per channel. Support for XDP_TX is implemented and the XDP buffer can safely be moved from the Rx to the Tx queue and correctly freed and returned to the XSK pool once it's transmitted. Note that when AF_XDP zero-copy is enabled, the XDP action XDP_PASS will allocate a new buffer and copy the zero-copy frame prior passing it to the kernel stack. This patch is based on previous work by Jakub Kicinski. Signed-off-by:
Niklas Söderlund <niklas.soderlund@corigine.com> Signed-off-by:
Simon Horman <simon.horman@corigine.com> Signed-off-by:
-
Niklas Söderlund authored
In preparation for adding AF_XDP support add a configuration check to make sure the buffer size can not be set to a larger value then the XSK socket chunk size. Signed-off-by:
-
Niklas Söderlund authored
Each data path needs an array of xsk pools to track if an xsk socket is in use. Add this array and make sure it's handled correctly when the data path is duplicated. Signed-off-by:
-
Jakub Kicinski authored
There will be more NAPI register logic once AF_XDP support is added, wrap our already conditional napi add/del into helpers. Signed-off-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by:
-
Niklas Söderlund authored
There are some common functionality that can be reused in the upcoming AF_XDP support. Expose those functions in the header. While at it mark some arguments of nfp_net_rx_csum() as const. Signed-off-by:
-
David S. Miller authored
Horatiu Vultur says: ==================== net: sparx5: Add PTP Hardware Clock support Add support for PTP Hardware Clock (PHC) for sparx5. ==================== Signed-off-by: -
Horatiu Vultur authored
Implement the function get_ts_info in ethtool_ops which is needed to get the HW capabilities for timestamping. Signed-off-by:
Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by:
-
Horatiu Vultur authored
When doing 2-step timestamping the HW will generate an interrupt when it managed to timestamp a frame. It is the SW responsibility to read it from the FIFO. Signed-off-by:
-
Horatiu Vultur authored
Update both the extraction and injection to do timestamping of the frames. The extraction is always doing the timestamping while for injection is doing the timestamping only if it is configured. Signed-off-by:
-
Horatiu Vultur authored
Implement the ioctl callbacks SIOCSHWTSTAMP and SIOCGHWTSTAMP to allow to configure the ports to enable/disable timestamping for TX. The RX timestamping is always enabled. The HW is capable to run both 1-step timestamping and 2-step timestamping. Signed-off-by:
-
Horatiu Vultur authored
The sparx5 has 3 PHC. Enable each of them, for now all the timestamping is happening on the first PHC. Signed-off-by:
-
Horatiu Vultur authored
Add the registers that will be used to configure the PHC in the HW. Signed-off-by:
-
Horatiu Vultur authored
Add support for ptp interrupt. This interrupt is used when using 2-step timestamping. For each timestamp that is added in a queue, an interrupt is generated. Signed-off-by:
-
Horatiu Vultur authored
Extend dt-bindings for sparx5 with ptp interrupt. This is generated when doing 2-step timestamping and the timestamp can be read from the FIFO. Signed-off-by:
-
Horatiu Vultur authored
Currently the ifh is not changed, it is fixed for each frame for each port that is sent out. Move this on the stack because this ifh needs to be change based on the frames that are send out. This is needed for PTP frames. Signed-off-by:
-
David S. Miller authored
Arun Ramadoss says: ==================== Add support for LAN937x T1 Phy Driver LAN937x is a Multi-port 100Base-T1 Switch and it internally uses LAN87xx T1 Phy. This series of patch update the initialization routine for the LAN87xx phy and also add LAN937x part support. Added the T1 Phy master-slave configuration through ethtool. ==================== Signed-off-by: -
Arun Ramadoss authored
To configure the T1 phy as master or slave using the ethtool -s <dev> master-slave <forced-master/forced-slave>, the config_aneg and read status functions are added. Signed-off-by:
Prasanna Vengateshan <prasanna.vengateshan@microchip.com> Signed-off-by:
Arun Ramadoss <arun.ramadoss@microchip.com> Signed-off-by:
-
Arun Ramadoss authored
LAN937x T1 switch is based on LAN87xx Phy, so reusing the init script of the LAN87xx. There is a workaround in accessing the DSP bank register for LAN937x Phy. Whenever there is a bank switch to DSP registers, then we need a one dummy read access before proceeding to the actual register access. Signed-off-by:
-
Arun Ramadoss authored
The new initialization sequence is the improvement to the existing init routine. Init routine does soft reset, run init script and set Hw_init. Added the new access_smi_poll_timeout() for polling smi bank write. Signed-off-by:
-
Arun Ramadoss authored
Removed the empty lines in struct phy_drivers. Signed-off-by:
-
Arun Ramadoss authored
Used the PHY_ID_MATCH_MODEL MACRO for describing the phy_id and phy_id_mask. Signed-off-by:
-
Arun Ramadoss authored
Replaced the current code of resetting of LAN87xx phy to genphy_soft_reset library function. Signed-off-by:
-
David S. Miller authored
Divya Koppera says: ==================== Add support for 1588 in LAN8814 The following patch series contains: - Fix for concurrent register access, which provides atomic access to extended page register reads/writes. - Provides dt-bindings related to latency and timestamping that are required for LAN8814 phy. - 1588 hardware timestamping support in LAN8814 phy. ==================== Signed-off-by: -
Divya Koppera authored
Add support for 1588 in LAN8814 phy driver. It supports 1-step and 2-step timestamping. Co-developed-by:
Divya Koppera <Divya.Koppera@microchip.com> Signed-off-by:
-
Divya Koppera authored
Supports configuring latency values and also adds check for phy timestamping feature. Signed-off-by: Divya Koppera<Divya.Koppera@microchip.com> Signed-off-by:
-
