imx6q-tbs2910 has an Atheros AR8035 Ethernet PHY at address 4.

The AR8035 provides a 125MHz clock to the ENET_REF_CLK i.MX6 pin.

Improve the Ethernet representation by adding an mdio node with such
information.

This fixes an Ethernet regression in U-Boot as U-Boot AR803X driver now
expects the 'qca,clk-out-frequency' property to be passed via
device tree.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Soeren Moch <smoch@web.de>
Tested-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

According to the AR8031 datasheet:

"When using crystal, clock is generated internally after the power is
stable. In order to get reliable power-on-reset, it is recommended to
keep asserting the reset low signal long enough (10 ms) to ensure the
clock is stable and clock-to-reset (1 ms) requirement is satisfied."

Pass the 'reset-assert-us' property to describe such requirement.

While at it, use the 'reset-gpios' property inside the the mdio
node instead of the deprecated usage of 'phy-reset-gpios'.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

imx6qdl-sabresd has an Atheros AR8031 Ethernet PHY at address 1.

The AR8031 provides a 125MHz clock to the ENET_REF_CLK i.MX6 pin.

Improve the Ethernet representation by adding an mdio node with such
information.

An advantage of adding the mdio node is that the AR8031 initialization
code in the mx6sabresd board file in U-Boot can totally be removed.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add Gateworks System Controller support to Gateworks Ventana boards:
- add dt bindings for GSC mfd driver and hwmon driver for ADC's and
  fan controllers.
- add dt bindings for gpio-keys driver for push-button and interrupt events
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for the MYiR imx6ULL based single board computer
equipped with on board 256MB NAND & RAM. The board also
provides expansion header for expansion board, but this
commit adds only support for SBC.
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add I2C child node for switch watchdog present on SPB4
Signed-off-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This is not necessary without a pinctrl-0 statement. Remove this
orphan.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The imx-pwm driver supports 3 cells and this is the more flexible setting.
So use it by default and overwrite it back to two for the files that
reference the PWMs with just 2 cells to minimize changes.

This allows to drop explicit setting to 3 cells for the boards that already
depend on this. The boards that are now using 2 cells explicitly can be
converted to 3 individually.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The SFF soldered onto the board expect the ports to use 1000BaseX.  It
makes no sense to have the ports set to SGMII, since they don't even
support that mode.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The SFF soldered onto the board expects the port to use 1000BaseX.  It
makes no sense to have the port set to SGMII, since it doesn't even
support that mode.
Signed-off-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Update MDIO configuration with ZII devices to fully utilize
MDIO endpoint capabilities.  All devices support 12.5MHz clock and
don't require MDIO preable.
Signed-off-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add node for CAAM device in NXP Vybrid SoC.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Enable SATA on iMX6QP SABRESD board.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Enable SATA on iMX6QP SABREAUTO board.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Protonic RVT is an internal development platform for a wireless ISObus
Virtual Terminal based on COTS tablets, and the predecessor of the WD2
platform.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The Protonic VT7 is a mid-class ISObus Virtual Terminal with a 7 inch
touchscreen display.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for the Protonic WD2 board, which is an internal development
platform for low-cost agricultural Virtual Terminals based on COTS tablets
and web applications.
It inherits from the PRTI6Q base class.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Protonic PRTI6Q is a development board and a base class for different
specific customer application boards based on the i.MX6 family of SoCs,
developed by Protonic Holland.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add ASRC device node.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Fix dtschema validator warnings like:
    l2-cache@a02000: $nodename:0:
        'l2-cache@a02000' does not match '^(cache-controller|cpu)(@[0-9a-f,]+)*$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Fix dtschema validator warnings like:
    l2-cache@40006000: $nodename:0:
        'l2-cache@40006000' does not match '^(cache-controller|cpu)(@[0-9a-f,]+)*$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add MQS support. As the pin conflict with usdhc2, then need
to add a separate dts.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The patch add ftm_alarm0 DT node
	- add rcpm node
	- add ftm_alarm0 node
	- aliases ftm_alarm0 as rtc1
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Complete the ESAI node and Add cs42888 sound card support.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add SPDIF support.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add SPDIF support.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add compatible string, update the clock table,
add fsl,asrc-rate and fsl,asrc-width property.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Use kernel LED interface for the alarm LEDs.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Samu Nuutamo <samu.nuutamo@vincit.fi>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

In imx6sll.dtsi, the ssi node name is different with other
platforms (imx6qdl, imx6sl, imx6sx), but the
sound/soc/fsl/fsl-asoc-card.c machine driver needs to check
ssi node name for audmux configuration, then different ssi
node name causes issue on imx6sll platform.

So we change ssi node name to make all platforms have same
name.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Change i.MX6/i.MX7 SoCs usdhc node name from usdhc to mmc to be
compliant with yaml schema, it requires the nodename to be "mmc".
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Change i.MX2/i.MX3/i.MX5 SoCs esdhc node name from esdhc to mmc to
be compliant with yaml schema, it requires the nodename to be "mmc".
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Change i.MX27/i.MX31 node name from sdhci to mmc to be compliant
with yaml schema, it requires the nodename to be "mmc".
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

In latest i.MX6Q RM Rev.6, 05/2020, #90 SPI interrupt is reserved,
so remove it from GPC node.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Change IIM node name from iim to efuse to be compliant
with yaml schema, it requires the nodename to be one of
"eeprom|efuse|nvram".
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Change OCOTP node name from ocotp to efuse to be compliant
with yaml schema, it requires the nodename to be one of
"eeprom|efuse|nvram".
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Change OCOTP node name from ocotp-ctrl to efuse to be compliant with
yaml schema, it requires the nodename to be one of "eeprom|efuse|nvram".
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The timer fixed interval period pulse generator register
is used to generate periodic pulses. The down count
register loads the value programmed in the fixed period
interval (FIPER). At every tick of the timer accumulator
overflow, the counter decrements by the value of
TMR_CTRL[TCLK_PERIOD]. It generates a pulse when the down
counter value reaches zero. It reloads the down counter
in the cycle following a pulse.

To use the TMR_FIPER register to generate desired periodic
pulses. The value should programmed is,
desired_period - tclk_period

Current tmr-fiper2 value is to generate 100us periodic pulses.
(But the value should have been 99995, not 99990. The tclk_period is 5.)
This patch is to generate 1 second periodic pulses with value
999999995 programmed which is more desired by user.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX6/7 SoCs' temperature sensor is inside anatop module from HW
perspective, so it should be a child node of anatop.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

According to Vybrid Security RM, CCM_CCGR11[CG176] can be used to gate
CAAM ipg clock.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-imx@nxp.com
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add mu root clk for mu mailbox usage.
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>