- 03 Dec, 2021 1 commit
-
-
Al Cooper authored
There is a small window in time during resume where the hardware flow control signal RTS can be asserted (which allows a sender to resume sending data to the UART) but the baud rate has not yet been restored. This will cause corrupted data and FRAMING, OVERRUN and BREAK errors. This is happening because the MCTRL register is shadowed in uart_port struct and is later used during resume to set the MCTRL register during both serial8250_do_startup() and uart_resume_port(). Unfortunately, serial8250_do_startup() happens before the UART baud rate is restored. The fix is to clear the shadowed mctrl value at the end of suspend and restore it at the end of resume. Fixes: 41a46948 ("serial: 8250: Add new 8250-core based Broadcom STB driver") Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Al Cooper <alcooperx@gmail.com> Link: https://lore.kernel.org/r/20211201201402.47446-1-alcooperx@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 25 Nov, 2021 14 commits
-
-
Jay Dolan authored
Have pericom_do_set_divisor() use the uartclk instead of a hard coded value to work with different speed crystals. Tested with 14.7456 and 24 MHz crystals. Have pericom_do_set_divisor() always calculate the divisor rather than call serial8250_do_set_divisor() for rates below baud_base. Do not write registers or call serial8250_do_set_divisor() if valid divisors could not be found. Fixes: 6bf4e42f ("serial: 8250: Add support for higher baud rates to Pericom chips") Cc: stable <stable@vger.kernel.org> Signed-off-by: Jay Dolan <jay.dolan@accesio.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20211122120604.3909-3-andriy.shevchenko@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jay Dolan authored
Fix error in table for PCI_DEVICE_ID_ACCESIO_PCIE_ICM_4S that caused it and PCI_DEVICE_ID_ACCESIO_PCIE_ICM232_4 to be missing their fourth port. Fixes: 78d3820b ("serial: 8250_pci: Have ACCES cards that use the four port Pericom PI7C9X7954 chip use the pci_pericom_setup()") Cc: stable <stable@vger.kernel.org> Signed-off-by: Jay Dolan <jay.dolan@accesio.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20211122120604.3909-2-andriy.shevchenko@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Lukas Wunner authored
Commit f45709df ("serial: 8250: Don't touch RTS modem control while in rs485 mode") sought to prevent user space from interfering with rs485 communication by ignoring a TIOCMSET ioctl() which changes RTS polarity. It did so in serial8250_do_set_mctrl(), which turns out to be too deep in the call stack: When a uart_port is opened, RTS polarity is set by the rs485-aware function uart_port_dtr_rts(). It calls down to serial8250_do_set_mctrl() and that particular RTS polarity change should *not* be ignored. The user-visible result is that on 8250_omap ports which use rs485 with inverse polarity (RTS bit in MCR register is 1 to receive, 0 to send), a newly opened port initially sets up RTS for sending instead of receiving. That's because omap_8250_startup() sets the cached value up->mcr to 0 and omap_8250_restore_regs() subsequently writes it to the MCR register. Due to the commit, serial8250_do_set_mctrl() preserves that incorrect register value: do_sys_openat2 do_filp_open path_openat vfs_open do_dentry_open chrdev_open tty_open uart_open tty_port_open uart_port_activate uart_startup uart_port_startup serial8250_startup omap_8250_startup # up->mcr = 0 uart_change_speed serial8250_set_termios omap_8250_set_termios omap_8250_restore_regs serial8250_out_MCR # up->mcr written tty_port_block_til_ready uart_dtr_rts uart_port_dtr_rts serial8250_set_mctrl omap8250_set_mctrl serial8250_do_set_mctrl # mcr[1] = 1 ignored Fix by intercepting RTS changes from user space in uart_tiocmset() instead. Link: https://lore.kernel.org/linux-serial/20211027111644.1996921-1-baocheng.su@siemens.com/ Fixes: f45709df ("serial: 8250: Don't touch RTS modem control while in rs485 mode") Cc: Chao Zeng <chao.zeng@siemens.com> Cc: stable@vger.kernel.org # v5.7+ Reported-by: Su Bao Cheng <baocheng.su@siemens.com> Reported-by: Jan Kiszka <jan.kiszka@siemens.com> Tested-by: Su Bao Cheng <baocheng.su@siemens.com> Signed-off-by: Lukas Wunner <lukas@wunner.de> Link: https://lore.kernel.org/r/21170e622a1aaf842a50b32146008b5374b3dd1d.1637596432.git.lukas@wunner.deSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alexander Stein authored
Revert commit b4b84493 ("tty: serial: fsl_lpuart: drop earlycon entry for i.MX8QXP"), because this breaks earlycon support on imx8qm/imx8qxp. While it is true that for earlycon there is no difference between i.MX8QXP and i.MX7ULP (for now at least), there are differences regarding clocks and fixups for wakeup support. For that reason it was deemed unacceptable to add the imx7ulp compatible to device tree in order to get earlycon working again. Reviewed-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Link: https://lore.kernel.org/r/20211124073109.805088-1-alexander.stein@ew.tq-group.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Patrik John authored
The current implementation uses 0 as lower limit for the baud rate tolerance for tegra20 and tegra30 chips which causes isses on UART initialization as soon as baud rate clock is lower than required even when within the standard UART tolerance of +/- 4%. This fix aligns the implementation with the initial commit description of +/- 4% tolerance for tegra chips other than tegra186 and tegra194. Fixes: d781ec21 ("serial: tegra: report clk rate errors") Cc: stable <stable@vger.kernel.org> Signed-off-by: Patrik John <patrik.john@u-blox.com> Link: https://lore.kernel.org/r/sig.19614244f8.20211123132737.88341-1-patrik.john@u-blox.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Johan Hovold authored
The LITEX symbol is neither a build or runtime dependency for the liteuart serial driver. LITEX is selected by the "LiteX SoC Controller" driver, which does a probe-time register-access sanity check and panics if the SoC has not been configured correctly. That driver's Kconfig entry asserts that any LiteX driver using the LiteX register accessors should depend on LITEX, but currently only the serial driver complies. Relax this LITEX "dependency" in order to make it easier to compile test the driver. Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20211117100512.5058-4-johan@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Johan Hovold authored
Make sure to release the allocated minor number before returning on probe errors. Fixes: 1da81e55 ("drivers/tty/serial: add LiteUART driver") Cc: stable@vger.kernel.org # 5.11 Cc: Filip Kokosinski <fkokosinski@antmicro.com> Cc: Mateusz Holenko <mholenko@antmicro.com> Reviewed-by: Stafford Horne <shorne@gmail.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20211117100512.5058-3-johan@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Johan Hovold authored
Deregister the port when unbinding the driver to prevent it from being used after releasing the driver data and leaking memory allocated by serial core. Fixes: 1da81e55 ("drivers/tty/serial: add LiteUART driver") Cc: stable@vger.kernel.org # 5.11 Cc: Filip Kokosinski <fkokosinski@antmicro.com> Cc: Mateusz Holenko <mholenko@antmicro.com> Reviewed-by: Stafford Horne <shorne@gmail.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20211117100512.5058-2-johan@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Ilia Sergachev authored
drvdata has to be set in _probe() - otherwise platform_get_drvdata() causes null pointer dereference BUG in _remove(). Fixes: 1da81e55 ("drivers/tty/serial: add LiteUART driver") Cc: stable <stable@vger.kernel.org> Reviewed-by: Johan Hovold <johan@kernel.org> Signed-off-by: Ilia Sergachev <silia@ethz.ch> Link: https://lore.kernel.org/r/20211115224944.23f8c12b@dtkwSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Maciej W. Rozycki authored
Fix a division by zero in `vgacon_resize' with a backtrace like: vgacon_resize vc_do_resize vgacon_init do_bind_con_driver do_unbind_con_driver fbcon_fb_unbind do_unregister_framebuffer do_register_framebuffer register_framebuffer __drm_fb_helper_initial_config_and_unlock drm_helper_hpd_irq_event dw_hdmi_irq irq_thread kthread caused by `c->vc_cell_height' not having been initialized. This has only started to trigger with commit 860dafa9 ("vt: Fix character height handling with VT_RESIZEX"), however the ultimate offender is commit 50ec42ed ("[PATCH] Detaching fbcon: fix vgacon to allow retaking of the console"). Said commit has added a call to `vc_resize' whenever `vgacon_init' is called with the `init' argument set to 0, which did not happen before. And the call is made before a key vgacon boot parameter retrieved in `vgacon_startup' has been propagated in `vgacon_init' for `vc_resize' to use to the console structure being worked on. Previously the parameter was `c->vc_font.height' and now it is `c->vc_cell_height'. In this particular scenario the registration of fbcon has failed and vt resorts to vgacon. Now fbcon does have initialized `c->vc_font.height' somehow, unlike `c->vc_cell_height', which is why this code did not crash before, but either way the boot parameters should have been copied to the console structure ahead of the call to `vc_resize' rather than afterwards, so that first the call has a chance to use them and second they do not change the console structure to something possibly different from what was used by `vc_resize'. Move the propagation of the vgacon boot parameters ahead of the call to `vc_resize' then. Adjust the comment accordingly. Fixes: 50ec42ed ("[PATCH] Detaching fbcon: fix vgacon to allow retaking of the console") Cc: stable@vger.kernel.org # v2.6.18+ Reported-by: Wim Osterholt <wim@djo.tudelft.nl> Reported-by: Pavel V. Panteleev <panteleev_p@mcst.ru> Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Link: https://lore.kernel.org/r/alpine.DEB.2.21.2110252317110.58149@angie.orcam.me.ukSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Sven Eckelmann authored
The CONSOLE_POLLING mode is used for tools like k(g)db. In this kind of setup, it is often sharing a serial device with the normal system console. This is usually no problem because the polling helpers can consume input values directly (when in kgdb context) and the normal Linux handlers can only consume new input values after kgdb switched back. This is not true anymore when RX DMA is enabled for UARTDM controllers. Single input values can no longer be received correctly. Instead following seems to happen: * on 1. input, some old input is read (continuously) * on 2. input, two old inputs are read (continuously) * on 3. input, three old input values are read (continuously) * on 4. input, 4 previous inputs are received This repeats then for each group of 4 input values. This behavior changes slightly depending on what state the controller was when the first input was received. But this makes working with kgdb basically impossible because control messages are always corrupted when kgdboc tries to parse them. RX DMA should therefore be off when CONSOLE_POLLING is enabled to avoid these kind of problems. No such problem was noticed for TX DMA. Fixes: 99693945 ("tty: serial: msm: Add RX DMA support") Cc: stable@vger.kernel.org Signed-off-by: Sven Eckelmann <sven@narfation.org> Link: https://lore.kernel.org/r/20211113121050.7266-1-sven@narfation.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Pierre Gondois authored
The document 'ACPI for Arm Components 1.0' defines the following _HID mappings: -'Prime cell UART (PL011)': ARMH0011 -'SBSA UART': ARMHB000 Use the sbsa-uart driver when a device is described with the 'ARMHB000' _HID. Note: PL011 devices currently use the sbsa-uart driver instead of the uart-pl011 driver. Indeed, PL011 devices are not bound to a clock in ACPI. It is not possible to change their baudrate. Cc: <stable@vger.kernel.org> Signed-off-by: Pierre Gondois <Pierre.Gondois@arm.com> Link: https://lore.kernel.org/r/20211109172248.19061-1-Pierre.Gondois@arm.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Johan Hovold authored
Commit 761ed4a9 ("tty: serial_core: convert uart_close to use tty_port_close") converted serial core to use tty_port_close() but failed to notice that the transmit buffer still needs to be freed on final close. Not freeing the transmit buffer means that the buffer is no longer cleared on next open so that any ioctl() waiting for the buffer to drain might wait indefinitely (e.g. on termios changes) or that stale data can end up being transmitted in case tx is restarted. Furthermore, the buffer of any port that has been opened would leak on driver unbind. Note that the port lock is held when clearing the buffer pointer due to the ldisc race worked around by commit a5ba1d95 ("uart: fix race between uart_put_char() and uart_shutdown()"). Also note that the tty-port shutdown() callback is not called for console ports so it is not strictly necessary to free the buffer page after releasing the lock (cf. d7240214 ("tty/serial: do not free trasnmit buffer page under port lock")). Link: https://lore.kernel.org/r/319321886d97c456203d5c6a576a5480d07c3478.1635781688.git.baruch@tkos.co.il Fixes: 761ed4a9 ("tty: serial_core: convert uart_close to use tty_port_close") Cc: stable@vger.kernel.org # 4.9 Cc: Rob Herring <robh@kernel.org> Reported-by: Baruch Siach <baruch@tkos.co.il> Tested-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20211108085431.12637-1-johan@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Arnaud Pouliquen authored
Adding myself as rpmsg tty maintainer and also adding remoteproc mailing list to inform about changes in the driver. Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com> Link: https://lore.kernel.org/r/20211102123817.19874-1-arnaud.pouliquen@foss.st.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 21 Nov, 2021 5 commits
-
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 fixes from Thomas Gleixner: - Move the command line preparation and the early command line parsing earlier so that the command line parameters which affect early_reserve_memory(), e.g. efi=nosftreserve, are taken into account. This was broken when the invocation of early_reserve_memory() was moved recently. - Use an atomic type for the SGX page accounting, which is read and written locklessly, to plug various race conditions related to it. * tag 'x86-urgent-2021-11-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/sgx: Fix free page accounting x86/boot: Pull up cmdline preparation and early param parsing
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 perf fixes from Thomas Gleixner: - Remove unneded PEBS disabling when taking LBR snapshots to prevent an unchecked MSR access error. - Fix IIO event constraints for Snowridge and Skylake server chips. * tag 'perf-urgent-2021-11-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/perf: Fix snapshot_branch_stack warning in VM perf/x86/intel/uncore: Fix IIO event constraints for Snowridge perf/x86/intel/uncore: Fix IIO event constraints for Skylake Server perf/x86/intel/uncore: Fix filter_tid mask for CHA events on Skylake Server
-
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linuxLinus Torvalds authored
Pull more powerpc fixes from Michael Ellerman: - Fix a bug in copying of sigset_t for 32-bit systems, which caused X to not start. - Fix handling of shared LSIs (rare) with the xive interrupt controller (Power9/10). - Fix missing TOC setup in some KVM code, which could result in oopses depending on kernel data layout. - Fix DMA mapping when we have persistent memory and only one DMA window available. - Fix further problems with STRICT_KERNEL_RWX on 8xx, exposed by a recent fix. - A couple of other minor fixes. Thanks to Alexey Kardashevskiy, Aneesh Kumar K.V, Cédric Le Goater, Christian Zigotzky, Christophe Leroy, Daniel Axtens, Finn Thain, Greg Kurz, Masahiro Yamada, Nicholas Piggin, and Uwe Kleine-König. * tag 'powerpc-5.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: powerpc/xive: Change IRQ domain to a tree domain powerpc/8xx: Fix pinned TLBs with CONFIG_STRICT_KERNEL_RWX powerpc/signal32: Fix sigset_t copy powerpc/book3e: Fix TLBCAM preset at boot powerpc/pseries/ddw: Do not try direct mapping with persistent memory and one window powerpc/pseries/ddw: simplify enable_ddw() powerpc/pseries/ddw: Revert "Extend upper limit for huge DMA window for persistent memory" powerpc/pseries: Fix numa FORM2 parsing fallback code powerpc/pseries: rename numa_dist_table to form2_distances powerpc: clean vdso32 and vdso64 directories powerpc/83xx/mpc8349emitx: Drop unused variable KVM: PPC: Book3S HV: Use GLOBAL_TOC for kvmppc_h_set_dabr/xdabr()
-
Geert Uytterhoeven authored
On 32-bit: fs/pstore/blk.c: In function ‘__best_effort_init’: include/linux/kern_levels.h:5:18: warning: format ‘%zu’ expects argument of type ‘size_t’, but argument 3 has type ‘long unsigned int’ [-Wformat=] 5 | #define KERN_SOH "\001" /* ASCII Start Of Header */ | ^~~~~~ include/linux/kern_levels.h:14:19: note: in expansion of macro ‘KERN_SOH’ 14 | #define KERN_INFO KERN_SOH "6" /* informational */ | ^~~~~~~~ include/linux/printk.h:373:9: note: in expansion of macro ‘KERN_INFO’ 373 | printk(KERN_INFO pr_fmt(fmt), ##__VA_ARGS__) | ^~~~~~~~~ fs/pstore/blk.c:314:3: note: in expansion of macro ‘pr_info’ 314 | pr_info("attached %s (%zu) (no dedicated panic_write!)\n", | ^~~~~~~ Cc: stable@vger.kernel.org Fixes: 7bb9557b ("pstore/blk: Use the normal block device I/O path") Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Kees Cook <keescook@chromium.org> Link: https://lore.kernel.org/r/20210629103700.1935012-1-geert@linux-m68k.org Cc: Jens Axboe <axboe@kernel.dk> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
- 20 Nov, 2021 20 commits
-
-
Linus Torvalds authored
Merge misc fixes from Andrew Morton: "15 patches. Subsystems affected by this patch series: ipc, hexagon, mm (swap, slab-generic, kmemleak, hugetlb, kasan, damon, and highmem), and proc" * emailed patches from Andrew Morton <akpm@linux-foundation.org>: proc/vmcore: fix clearing user buffer by properly using clear_user() kmap_local: don't assume kmap PTEs are linear arrays in memory mm/damon/dbgfs: fix missed use of damon_dbgfs_lock mm/damon/dbgfs: use '__GFP_NOWARN' for user-specified size buffer allocation kasan: test: silence intentional read overflow warnings hugetlb, userfaultfd: fix reservation restore on userfaultfd error hugetlb: fix hugetlb cgroup refcounting during mremap mm: kmemleak: slob: respect SLAB_NOLEAKTRACE flag hexagon: ignore vmlinux.lds hexagon: clean up timer-regs.h hexagon: export raw I/O routines for modules mm: emit the "free" trace report before freeing memory in kmem_cache_free() shm: extend forced shm destroy to support objects from several IPC nses ipc: WARN if trying to remove ipc object which is absent mm/swap.c:put_pages_list(): reinitialise the page list
-
git://git.kernel.dk/linux-blockLinus Torvalds authored
Pull block fixes from Jens Axboe: - Flip a cap check to avoid a selinux error (Alistair) - Fix for a regression this merge window where we can miss a queue ref put (me) - Un-mark pstore-blk as broken, as the condition that triggered that change has been rectified (Kees) - Queue quiesce and sync fixes (Ming) - FUA insertion fix (Ming) - blk-cgroup error path put fix (Yu) * tag 'block-5.16-2021-11-19' of git://git.kernel.dk/linux-block: blk-mq: don't insert FUA request with data into scheduler queue blk-cgroup: fix missing put device in error path from blkg_conf_pref() block: avoid to quiesce queue in elevator_init_mq Revert "mark pstore-blk as broken" blk-mq: cancel blk-mq dispatch work in both blk_cleanup_queue and disk_release() block: fix missing queue put in error path block: Check ADMIN before NICE for IOPRIO_CLASS_RT
-
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrlLinus Torvalds authored
Pull pin control fixes from Linus Walleij: "There is an ACPI stubs fix which is ACKed by the ACPI maintainer for merging through my tree. One item stand out and that is that I delete the <linux/sdb.h> header that is used by nothing. I deleted this subsystem (through the GPIO tree) a while back so I feel responsible for tidying up the floor. Other than that it is the usual mistakes, a bit noisy around build issue and Kconfig then driver fixes. Specifics: - Fix some stubs causing compile issues for ACPI. - Fix some wakeups on AMD IRQs shared between GPIO and SCI. - Fix a build warning in the Tegra driver. - Fix a Kconfig issue in the Qualcomm driver. - Add a missing include the RALink driver. - Return a valid type for the Apple pinctrl IRQs. - Implement some Qualcomm SDM845 dual-edge errata. - Remove the unused <linux/sdb.h> header. (The subsystem was once deleted by the pinctrl maintainer...) - Fix a duplicate initialized in the Tegra driver. - Fix register offsets for UFS and SDC in the Qualcomm SM8350 driver" * tag 'pinctrl-v5.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: pinctrl: qcom: sm8350: Correct UFS and SDC offsets pinctrl: tegra194: remove duplicate initializer again Remove unused header <linux/sdb.h> pinctrl: qcom: sdm845: Enable dual edge errata pinctrl: apple: Always return valid type in apple_gpio_irq_type pinctrl: ralink: include 'ralink_regs.h' in 'pinctrl-mt7620.c' pinctrl: qcom: fix unmet dependencies on GPIOLIB for GPIOLIB_IRQCHIP pinctrl: tegra: Return const pointer from tegra_pinctrl_get_group() pinctrl: amd: Fix wakeups when IRQ is shared with SCI ACPI: Add stubs for wakeup handler functions
-
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linuxLinus Torvalds authored
Pull s390 updates from Heiko Carstens: - Add missing Kconfig option for ftrace direct multi sample, so it can be compiled again, and also add s390 support for this sample. - Update Christian Borntraeger's email address. - Various fixes for memory layout setup. Besides other this makes it possible to load shared DCSS segments again. - Fix copy to user space of swapped kdump oldmem. - Remove -mstack-guard and -mstack-size compile options when building vdso binaries. This can happen when CONFIG_VMAP_STACK is disabled and results in broken vdso code which causes more or less random exceptions. Also remove the not needed -nostdlib option. - Fix memory leak on cpu hotplug and return code handling in kexec code. - Wire up futex_waitv system call. - Replace snprintf with sysfs_emit where appropriate. * tag 's390-5.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: ftrace/samples: add s390 support for ftrace direct multi sample ftrace/samples: add missing Kconfig option for ftrace direct multi sample MAINTAINERS: update email address of Christian Borntraeger s390/kexec: fix memory leak of ipl report buffer s390/kexec: fix return code handling s390/dump: fix copying to user-space of swapped kdump oldmem s390: wire up sys_futex_waitv system call s390/vdso: filter out -mstack-guard and -mstack-size s390/vdso: remove -nostdlib compiler flag s390: replace snprintf in show functions with sysfs_emit s390/boot: simplify and fix kernel memory layout setup s390/setup: re-arrange memblock setup s390/setup: avoid using memblock_enforce_memory_limit s390/setup: avoid reserving memory above identity mapping
-
git://git.samba.org/sfrench/cifs-2.6Linus Torvalds authored
Pull cifs fixes from Steve French: "Three small cifs/smb3 fixes: two to address minor coverity issues and one cleanup" * tag '5.16-rc1-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6: cifs: introduce cifs_ses_mark_for_reconnect() helper cifs: protect srv_count with cifs_tcp_ses_lock cifs: move debug print out of spinlock
-
David Hildenbrand authored
To clear a user buffer we cannot simply use memset, we have to use clear_user(). With a virtio-mem device that registers a vmcore_cb and has some logically unplugged memory inside an added Linux memory block, I can easily trigger a BUG by copying the vmcore via "cp": systemd[1]: Starting Kdump Vmcore Save Service... kdump[420]: Kdump is using the default log level(3). kdump[453]: saving to /sysroot/var/crash/127.0.0.1-2021-11-11-14:59:22/ kdump[458]: saving vmcore-dmesg.txt to /sysroot/var/crash/127.0.0.1-2021-11-11-14:59:22/ kdump[465]: saving vmcore-dmesg.txt complete kdump[467]: saving vmcore BUG: unable to handle page fault for address: 00007f2374e01000 #PF: supervisor write access in kernel mode #PF: error_code(0x0003) - permissions violation PGD 7a523067 P4D 7a523067 PUD 7a528067 PMD 7a525067 PTE 800000007048f867 Oops: 0003 [#1] PREEMPT SMP NOPTI CPU: 0 PID: 468 Comm: cp Not tainted 5.15.0+ #6 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.14.0-27-g64f37cc530f1-prebuilt.qemu.org 04/01/2014 RIP: 0010:read_from_oldmem.part.0.cold+0x1d/0x86 Code: ff ff ff e8 05 ff fe ff e9 b9 e9 7f ff 48 89 de 48 c7 c7 38 3b 60 82 e8 f1 fe fe ff 83 fd 08 72 3c 49 8d 7d 08 4c 89 e9 89 e8 <49> c7 45 00 00 00 00 00 49 c7 44 05 f8 00 00 00 00 48 83 e7 f81 RSP: 0018:ffffc9000073be08 EFLAGS: 00010212 RAX: 0000000000001000 RBX: 00000000002fd000 RCX: 00007f2374e01000 RDX: 0000000000000001 RSI: 00000000ffffdfff RDI: 00007f2374e01008 RBP: 0000000000001000 R08: 0000000000000000 R09: ffffc9000073bc50 R10: ffffc9000073bc48 R11: ffffffff829461a8 R12: 000000000000f000 R13: 00007f2374e01000 R14: 0000000000000000 R15: ffff88807bd421e8 FS: 00007f2374e12140(0000) GS:ffff88807f000000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f2374e01000 CR3: 000000007a4aa000 CR4: 0000000000350eb0 Call Trace: read_vmcore+0x236/0x2c0 proc_reg_read+0x55/0xa0 vfs_read+0x95/0x190 ksys_read+0x4f/0xc0 do_syscall_64+0x3b/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae Some x86-64 CPUs have a CPU feature called "Supervisor Mode Access Prevention (SMAP)", which is used to detect wrong access from the kernel to user buffers like this: SMAP triggers a permissions violation on wrong access. In the x86-64 variant of clear_user(), SMAP is properly handled via clac()+stac(). To fix, properly use clear_user() when we're dealing with a user buffer. Link: https://lkml.kernel.org/r/20211112092750.6921-1-david@redhat.com Fixes: 997c136f ("fs/proc/vmcore.c: add hook to read_from_oldmem() to check for non-ram pages") Signed-off-by: David Hildenbrand <david@redhat.com> Acked-by: Baoquan He <bhe@redhat.com> Cc: Dave Young <dyoung@redhat.com> Cc: Baoquan He <bhe@redhat.com> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Philipp Rudo <prudo@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Ard Biesheuvel authored
The kmap_local conversion broke the ARM architecture, because the new code assumes that all PTEs used for creating kmaps form a linear array in memory, and uses array indexing to look up the kmap PTE belonging to a certain kmap index. On ARM, this cannot work, not only because the PTE pages may be non-adjacent in memory, but also because ARM/!LPAE interleaves hardware entries and extended entries (carrying software-only bits) in a way that is not compatible with array indexing. Fortunately, this only seems to affect configurations with more than 8 CPUs, due to the way the per-CPU kmap slots are organized in memory. Work around this by permitting an architecture to set a Kconfig symbol that signifies that the kmap PTEs do not form a lineary array in memory, and so the only way to locate the appropriate one is to walk the page tables. Link: https://lore.kernel.org/linux-arm-kernel/20211026131249.3731275-1-ardb@kernel.org/ Link: https://lkml.kernel.org/r/20211116094737.7391-1-ardb@kernel.org Fixes: 2a15ba82 ("ARM: highmem: Switch to generic kmap atomic") Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Reported-by: Quanyang Wang <quanyang.wang@windriver.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
SeongJae Park authored
DAMON debugfs is supposed to protect dbgfs_ctxs, dbgfs_nr_ctxs, and dbgfs_dirs using damon_dbgfs_lock. However, some of the code is accessing the variables without the protection. This fixes it by protecting all such accesses. Link: https://lkml.kernel.org/r/20211110145758.16558-3-sj@kernel.org Fixes: 75c1c2b5 ("mm/damon/dbgfs: support multiple contexts") Signed-off-by: SeongJae Park <sj@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
SeongJae Park authored
Patch series "DAMON fixes". This patch (of 2): DAMON users can trigger below warning in '__alloc_pages()' by invoking write() to some DAMON debugfs files with arbitrarily high count argument, because DAMON debugfs interface allocates some buffers based on the user-specified 'count'. if (unlikely(order >= MAX_ORDER)) { WARN_ON_ONCE(!(gfp & __GFP_NOWARN)); return NULL; } Because the DAMON debugfs interface code checks failure of the 'kmalloc()', this commit simply suppresses the warnings by adding '__GFP_NOWARN' flag. Link: https://lkml.kernel.org/r/20211110145758.16558-1-sj@kernel.org Link: https://lkml.kernel.org/r/20211110145758.16558-2-sj@kernel.org Fixes: 4bc05954 ("mm/damon: implement a debugfs-based user space interface") Signed-off-by: SeongJae Park <sj@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Kees Cook authored
As done in commit d73dad4e ("kasan: test: bypass __alloc_size checks") for __write_overflow warnings, also silence some more cases that trip the __read_overflow warnings seen in 5.16-rc1[1]: In file included from include/linux/string.h:253, from include/linux/bitmap.h:10, from include/linux/cpumask.h:12, from include/linux/mm_types_task.h:14, from include/linux/mm_types.h:5, from include/linux/page-flags.h:13, from arch/arm64/include/asm/mte.h:14, from arch/arm64/include/asm/pgtable.h:12, from include/linux/pgtable.h:6, from include/linux/kasan.h:29, from lib/test_kasan.c:10: In function 'memcmp', inlined from 'kasan_memcmp' at lib/test_kasan.c:897:2: include/linux/fortify-string.h:263:25: error: call to '__read_overflow' declared with attribute error: detected read beyond size of object (1st parameter) 263 | __read_overflow(); | ^~~~~~~~~~~~~~~~~ In function 'memchr', inlined from 'kasan_memchr' at lib/test_kasan.c:872:2: include/linux/fortify-string.h:277:17: error: call to '__read_overflow' declared with attribute error: detected read beyond size of object (1st parameter) 277 | __read_overflow(); | ^~~~~~~~~~~~~~~~~ [1] http://kisskb.ellerman.id.au/kisskb/buildresult/14660585/log/ Link: https://lkml.kernel.org/r/20211116004111.3171781-1-keescook@chromium.org Fixes: d73dad4e ("kasan: test: bypass __alloc_size checks") Signed-off-by: Kees Cook <keescook@chromium.org> Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com> Acked-by: Marco Elver <elver@google.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Alexander Potapenko <glider@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Mina Almasry authored
Currently in the is_continue case in hugetlb_mcopy_atomic_pte(), if we bail out using "goto out_release_unlock;" in the cases where idx >= size, or !huge_pte_none(), the code will detect that new_pagecache_page == false, and so call restore_reserve_on_error(). In this case I see restore_reserve_on_error() delete the reservation, and the following call to remove_inode_hugepages() will increment h->resv_hugepages causing a 100% reproducible leak. We should treat the is_continue case similar to adding a page into the pagecache and set new_pagecache_page to true, to indicate that there is no reservation to restore on the error path, and we need not call restore_reserve_on_error(). Rename new_pagecache_page to page_in_pagecache to make that clear. Link: https://lkml.kernel.org/r/20211117193825.378528-1-almasrymina@google.com Fixes: c7b1850d ("hugetlb: don't pass page cache pages to restore_reserve_on_error") Signed-off-by: Mina Almasry <almasrymina@google.com> Reported-by: James Houghton <jthoughton@google.com> Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com> Cc: Wei Xu <weixugc@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Bui Quang Minh authored
When hugetlb_vm_op_open() is called during copy_vma(), we may take the reference to resv_map->css. Later, when clearing the reservation pointer of old_vma after transferring it to new_vma, we forget to drop the reference to resv_map->css. This leads to a reference leak of css. Fixes this by adding a check to drop reservation css reference in clear_vma_resv_huge_pages() Link: https://lkml.kernel.org/r/20211113154412.91134-1-minhquangbui99@gmail.com Fixes: 550a7d60 ("mm, hugepages: add mremap() support for hugepage backed vma") Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com> Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com> Reviewed-by: Mina Almasry <almasrymina@google.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Muchun Song <songmuchun@bytedance.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Rustam Kovhaev authored
When kmemleak is enabled for SLOB, system does not boot and does not print anything to the console. At the very early stage in the boot process we hit infinite recursion from kmemleak_init() and eventually kernel crashes. kmemleak_init() specifies SLAB_NOLEAKTRACE for KMEM_CACHE(), but kmem_cache_create_usercopy() removes it because CACHE_CREATE_MASK is not valid for SLOB. Let's fix CACHE_CREATE_MASK and make kmemleak work with SLOB Link: https://lkml.kernel.org/r/20211115020850.3154366-1-rkovhaev@gmail.com Fixes: d8843922 ("slab: Ignore internal flags in cache creation") Signed-off-by: Rustam Kovhaev <rkovhaev@gmail.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Reviewed-by: Muchun Song <songmuchun@bytedance.com> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Glauber Costa <glommer@parallels.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Nathan Chancellor authored
After building allmodconfig, there is an untracked vmlinux.lds file in arch/hexagon/kernel: $ git ls-files . --exclude-standard --others arch/hexagon/kernel/vmlinux.lds Ignore it as all other architectures have. Link: https://lkml.kernel.org/r/20211115174250.1994179-4-nathan@kernel.orgSigned-off-by: Nathan Chancellor <nathan@kernel.org> Cc: Brian Cain <bcain@codeaurora.org> Cc: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Nathan Chancellor authored
When building allmodconfig, there is a warning about TIMER_ENABLE being redefined: drivers/clocksource/timer-oxnas-rps.c:39:9: error: 'TIMER_ENABLE' macro redefined [-Werror,-Wmacro-redefined] #define TIMER_ENABLE BIT(7) ^ arch/hexagon/include/asm/timer-regs.h:13:9: note: previous definition is here #define TIMER_ENABLE 0 ^ 1 error generated. The values in this header are only used in one file each, if they are used at all. Remove the header and sink all of the constants into their respective files. TCX0_CLK_RATE is only used in arch/hexagon/include/asm/timex.h TIMER_ENABLE, RTOS_TIMER_INT, RTOS_TIMER_REGS_ADDR are only used in arch/hexagon/kernel/time.c. SLEEP_CLK_RATE and TIMER_CLR_ON_MATCH have both been unused since the file's introduction in commit 71e4a47f ("Hexagon: Add time and timer functions"). TIMER_ENABLE is redefined as BIT(0) so the shift is moved into the definition, rather than its use. Link: https://lkml.kernel.org/r/20211115174250.1994179-3-nathan@kernel.orgSigned-off-by: Nathan Chancellor <nathan@kernel.org> Acked-by: Brian Cain <bcain@codeaurora.org> Cc: Nick Desaulniers <ndesaulniers@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Nathan Chancellor authored
Patch series "Fixes for ARCH=hexagon allmodconfig", v2. This series fixes some issues noticed with ARCH=hexagon allmodconfig. This patch (of 3): When building ARCH=hexagon allmodconfig, the following errors occur: ERROR: modpost: "__raw_readsl" [drivers/i3c/master/svc-i3c-master.ko] undefined! ERROR: modpost: "__raw_writesl" [drivers/i3c/master/dw-i3c-master.ko] undefined! ERROR: modpost: "__raw_readsl" [drivers/i3c/master/dw-i3c-master.ko] undefined! ERROR: modpost: "__raw_writesl" [drivers/i3c/master/i3c-master-cdns.ko] undefined! ERROR: modpost: "__raw_readsl" [drivers/i3c/master/i3c-master-cdns.ko] undefined! Export these symbols so that modules can use them without any errors. Link: https://lkml.kernel.org/r/20211115174250.1994179-1-nathan@kernel.org Link: https://lkml.kernel.org/r/20211115174250.1994179-2-nathan@kernel.org Fixes: 013bf24c ("Hexagon: Provide basic implementation and/or stubs for I/O routines.") Signed-off-by: Nathan Chancellor <nathan@kernel.org> Acked-by: Brian Cain <bcain@codeaurora.org> Cc: Nick Desaulniers <ndesaulniers@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Yunfeng Ye authored
After the memory is freed, it can be immediately allocated by other CPUs, before the "free" trace report has been emitted. This causes inaccurate traces. For example, if the following sequence of events occurs: CPU 0 CPU 1 (1) alloc xxxxxx (2) free xxxxxx (3) alloc xxxxxx (4) free xxxxxx Then they will be inaccurately reported via tracing, so that they appear to have happened in this order: CPU 0 CPU 1 (1) alloc xxxxxx (2) alloc xxxxxx (3) free xxxxxx (4) free xxxxxx This makes it look like CPU 1 somehow managed to allocate memory that CPU 0 still had allocated for itself. In order to avoid this, emit the "free xxxxxx" tracing report just before the actual call to free the memory, instead of just after it. Link: https://lkml.kernel.org/r/374eb75d-7404-8721-4e1e-65b0e5b17279@huawei.comSigned-off-by: Yunfeng Ye <yeyunfeng@huawei.com> Reviewed-by: Vlastimil Babka <vbabka@suse.cz> Reviewed-by: John Hubbard <jhubbard@nvidia.com> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Alexander Mikhalitsyn authored
Currently, the exit_shm() function not designed to work properly when task->sysvshm.shm_clist holds shm objects from different IPC namespaces. This is a real pain when sysctl kernel.shm_rmid_forced = 1, because it leads to use-after-free (reproducer exists). This is an attempt to fix the problem by extending exit_shm mechanism to handle shm's destroy from several IPC ns'es. To achieve that we do several things: 1. add a namespace (non-refcounted) pointer to the struct shmid_kernel 2. during new shm object creation (newseg()/shmget syscall) we initialize this pointer by current task IPC ns 3. exit_shm() fully reworked such that it traverses over all shp's in task->sysvshm.shm_clist and gets IPC namespace not from current task as it was before but from shp's object itself, then call shm_destroy(shp, ns). Note: We need to be really careful here, because as it was said before (1), our pointer to IPC ns non-refcnt'ed. To be on the safe side we using special helper get_ipc_ns_not_zero() which allows to get IPC ns refcounter only if IPC ns not in the "state of destruction". Q/A Q: Why can we access shp->ns memory using non-refcounted pointer? A: Because shp object lifetime is always shorther than IPC namespace lifetime, so, if we get shp object from the task->sysvshm.shm_clist while holding task_lock(task) nobody can steal our namespace. Q: Does this patch change semantics of unshare/setns/clone syscalls? A: No. It's just fixes non-covered case when process may leave IPC namespace without getting task->sysvshm.shm_clist list cleaned up. Link: https://lkml.kernel.org/r/67bb03e5-f79c-1815-e2bf-949c67047418@colorfullife.com Link: https://lkml.kernel.org/r/20211109151501.4921-1-manfred@colorfullife.com Fixes: ab602f79 ("shm: make exit_shm work proportional to task activity") Co-developed-by: Manfred Spraul <manfred@colorfullife.com> Signed-off-by: Manfred Spraul <manfred@colorfullife.com> Signed-off-by: Alexander Mikhalitsyn <alexander.mikhalitsyn@virtuozzo.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Greg KH <gregkh@linuxfoundation.org> Cc: Andrei Vagin <avagin@gmail.com> Cc: Pavel Tikhomirov <ptikhomirov@virtuozzo.com> Cc: Vasily Averin <vvs@virtuozzo.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Alexander Mikhalitsyn authored
Patch series "shm: shm_rmid_forced feature fixes". Some time ago I met kernel crash after CRIU restore procedure, fortunately, it was CRIU restore, so, I had dump files and could do restore many times and crash reproduced easily. After some investigation I've constructed the minimal reproducer. It was found that it's use-after-free and it happens only if sysctl kernel.shm_rmid_forced = 1. The key of the problem is that the exit_shm() function not handles shp's object destroy when task->sysvshm.shm_clist contains items from different IPC namespaces. In most cases this list will contain only items from one IPC namespace. How can this list contain object from different namespaces? The exit_shm() function is designed to clean up this list always when process leaves IPC namespace. But we made a mistake a long time ago and did not add a exit_shm() call into the setns() syscall procedures. The first idea was just to add this call to setns() syscall but it obviously changes semantics of setns() syscall and that's userspace-visible change. So, I gave up on this idea. The first real attempt to address the issue was just to omit forced destroy if we meet shp object not from current task IPC namespace [1]. But that was not the best idea because task->sysvshm.shm_clist was protected by rwsem which belongs to current task IPC namespace. It means that list corruption may occur. Second approach is just extend exit_shm() to properly handle shp's from different IPC namespaces [2]. This is really non-trivial thing, I've put a lot of effort into that but not believed that it's possible to make it fully safe, clean and clear. Thanks to the efforts of Manfred Spraul working an elegant solution was designed. Thanks a lot, Manfred! Eric also suggested the way to address the issue in ("[RFC][PATCH] shm: In shm_exit destroy all created and never attached segments") Eric's idea was to maintain a list of shm_clists one per IPC namespace, use lock-less lists. But there is some extra memory consumption-related concerns. An alternative solution which was suggested by me was implemented in ("shm: reset shm_clist on setns but omit forced shm destroy"). The idea is pretty simple, we add exit_shm() syscall to setns() but DO NOT destroy shm segments even if sysctl kernel.shm_rmid_forced = 1, we just clean up the task->sysvshm.shm_clist list. This chages semantics of setns() syscall a little bit but in comparision to the "naive" solution when we just add exit_shm() without any special exclusions this looks like a safer option. [1] https://lkml.org/lkml/2021/7/6/1108 [2] https://lkml.org/lkml/2021/7/14/736 This patch (of 2): Let's produce a warning if we trying to remove non-existing IPC object from IPC namespace kht/idr structures. This allows us to catch possible bugs when the ipc_rmid() function was called with inconsistent struct ipc_ids*, struct kern_ipc_perm* arguments. Link: https://lkml.kernel.org/r/20211027224348.611025-1-alexander.mikhalitsyn@virtuozzo.com Link: https://lkml.kernel.org/r/20211027224348.611025-2-alexander.mikhalitsyn@virtuozzo.comCo-developed-by: Manfred Spraul <manfred@colorfullife.com> Signed-off-by: Manfred Spraul <manfred@colorfullife.com> Signed-off-by: Alexander Mikhalitsyn <alexander.mikhalitsyn@virtuozzo.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Greg KH <gregkh@linuxfoundation.org> Cc: Andrei Vagin <avagin@gmail.com> Cc: Pavel Tikhomirov <ptikhomirov@virtuozzo.com> Cc: Vasily Averin <vvs@virtuozzo.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Matthew Wilcox authored
While free_unref_page_list() puts pages onto the CPU local LRU list, it does not remove them from the list they were passed in on. That makes the list_head appear to be non-empty, and would lead to various corruption problems if we didn't have an assertion that the list was empty. Reinitialise the list after calling free_unref_page_list() to avoid this problem. Link: https://lkml.kernel.org/r/YYp40A2lNrxaZji8@casper.infradead.org Fixes: 988c69f1 ("mm: optimise put_pages_list()") Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Reviewed-by: Steve French <stfrench@microsoft.com> Reported-by: Namjae Jeon <linkinjeon@kernel.org> Tested-by: Steve French <stfrench@microsoft.com> Tested-by: Namjae Jeon <linkinjeon@kernel.org> Cc: Steve French <smfrench@gmail.com> Cc: Hyeoncheol Lee <hyc.lee@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-