GitLab

_UCODE_API_OK was a intermediate version between MIN and
MAX. If a user had a firmware below _OK but above _MIN, the
driver would work but the user would get a warning in the
kernel log telling him to update his firmware.
This is not needed since most users won't look for these
messages in the kernel log if their wifi is working.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Declare and enable support of RX and TX checksum for 9000 family.
Configure offload_assist in the TX cmd accordingly to support
TX csum.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

If something goes wrong with the firmware and we never get a scan
complete notification, we stay stuck forever.  In order to avoid this
situation, add a timeout and trigger an NMI if it expires before
receiving the notification., so we can clean things up.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Change the CMD queue to be queue #0 (rather than queue #9)
when working in DQA mode.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

In DQA mode, allocate a dedicated queue (#3) for content
after beacon (AKA "CaB").
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Set the correct sta_id in the SCD_QUEUE_CONFIG command sent
to the FW when enabling/disabling queues. This is needed in
DQA-mode to allow the FW to associate between queue and STA.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Use the reserved BSS Client queue when connecting to an AP
in DQA mode.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Edit some of the 9560 series and 5165 series PCI IDs.
These devices do not exist yet.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Improve current RSS configuration:
 * Use netdev_rss_key instead of keeping a local copy.
 * Configure also UDP hashing to have UDP traffic spread across queues.
 * Do not direct RSS traffic to our fallback queue.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

We want to request an interrupt vector for RSS queue per CPU,
one vector for fallback queue, and one for non-rx interrupts.
Future patch will make sure that no RSS traffic is directed to
fallback queue.
This will enable us to enable fast path on traffic that otherwise
would have been received on the fallback queue.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The driver can read the current state during D0I3,
therefore there is no reason not to do it.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

For some reason, this was defined as a signed variable.
Make it unsigned.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Auxilary station ID in flag in scan config command wasn't set
although we set the station ID. Add the flag.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Currently the code checks if hardware reported both L4 and L3
checksums as valid, and only then reports it as validated to
the stack.
However, IPv6 does not have checksum at all and the L3 checksum
valid bit is always off for IPv6 packets, with the result of the
stack re-validating L4 checksum.
Fix code to set CHECKSUM_UNNECESSARY also for IPv6 packets whose
TCP/UDP checksum was verified.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Use alloc_ordered_workqueue() to allocate the workqueue instead of
create_singlethread_workqueue() since the latter is deprecated and is scheduled
for removal.

There are work items doing related operations that shouldn't be swapped when
queued in a certain order hence preserve the strict execution ordering of a
single threaded (ST) workqueue by switching to alloc_ordered_workqueue().

WQ_MEM_RECLAIM flag is not needed since the worker is not depended
during memory reclaim.
Signed-off-by: Eva Rachel Retuya <eraretuya@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

API version lower than 16 is not supported anymore - don't
load older ucode.
Remove code handling older versions.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Gscan capabilities were updated with new capabilities supported
by the device. Update GSCAN capabilities TLV.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

We have a module parameter, this is enough.
per platform customizations will be done through the init
script of the platform.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Due to hardware bug, upon any shadow free-queue register write
access, a legacy RBD shadow register must be written as well.
This is required in order to trigger a copy of the shadow registers
values after MAC exits sleep state.
Specifically, the driver has to write (any value) to the legacy RBD
register each time FRBDCB is accessed.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

"DQA" is shorthand for "dynamic queue allocation". This
enables on-demand allocation of queues per RA/TID rather than
statically allocating per vif, thus allowing a potential
benefit of various factors.

Please refer to the DOC section this patch adds to sta.h to
see a more in-depth explanation of this feature.

There are many things to take into consideration when working
in DQA mode, and this patch is only one in a series. Note that
default operation mode is non-DQA mode, unless the FW
indicates that it supports DQA mode.

This patch enables support of DQA for a station connected to
an AP, and works in a non-aggregated mode.

When a frame for an unused RA/TID arrives at the driver, it
isn't TXed immediately, but deferred first until a suitable
queue is first allocated for it, and then TXed by a worker
that both allocates the queues and TXes deferred traffic.

When a STA is removed, its queues goes back into the queue
pools for reuse as needed.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

"is_data_qos == true" is equivalent to "tid < IWL_MAX_TID_COUNT"
since tid is only assigned (and range-checked) in that case.

This removes a (harmless) smatch warning that occurs because it
can't seem to follow the above logic from the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Update device id and FW serial number for 2X2 antenna devices
in 9000 generation product. These will not be available on
the market in the coming year.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This allows to disable uapsd for BSS only, or P2P client
separately. Remove the now unneeded
IWL_MVM_P2P_UAPSD_STANDALONE constant.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

iwlwifi / iwlmvm didn't destroy their mutexes. Fix that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

TX CMD API has changed to support offload assist.
Currently we do not enable checksum yet, but must set the
padding indication, to avoid FW errors.
Set other amsdu flag as well.
The rest of the flags will be configured only if HW csum
is enabled and will be set in future patches.
This change is backward compatible.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

We insert padding if the MAC header's size is not a multiple of 4
to ensure that the SNAP header is DWORD aligned. When we do so, we
let the firmware know by setting a bit in Tx command
(TX_CMD_FLG_MH_PAD) which will instruct the firmware to drop those
2 bytes before sending the frame.
However, this is not needed for AMSDU as the sub frame header (14B)
complements the MAC header (26B) so that the SNAP header is DWORD
aligned without adding any pad.

Until 9000, the firmware didn't check the TX_CMD_FLG_MH_PAD bit
but rather checked the length of the MAC header itself and
assumed the entity that enqueued the frame (driver or internal
firmware code) added the pad.
Since the driver inserted the pad even for AMSDU this logic applied.
Note that the padding is a DMA optimization but it's not strictly
needed, so we could pad even if it was not needed.

However, the CSUM hardware introduced for the 9000 devices requires
to not pad AMSDU as it is not needed, and will fail if such a pad
exists.
Due to older FW not checking the padding bit but checking the mac
header size itself - we cannot do this adjustments for older
generations.
Do not align the size if it is an AMSDU and HW checksum is enabled -
which will only happen on 9000 devices and on.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This makes u-APSD work with more peers.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Bjorn pointed out that printing an error value as an
hexadecimal isn't very convenient. Change that.
Reported-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Use RX_HANDLER_ASYNC_UNLOCKED instead of unlock and re-lock
the mutex independently.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

We don't use the refcount value anymore, all the refcounting is done
in the runtime PM usage_count value.  Remove it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

When entering suspend the driver calls iwl_disable_interrupts() and
then iwl_pcie_disable_ict().
On resume the driver calls only iwl_pcie_reset_ict() without calling
explicitly to iwl_enable_interrupts().
This mostly works since iwl_pcie_reset_ict is calling to
iwl_enable_interrupts, but it doesn't work when there is no ict_table
in MSIx mode.
The result is that driver tries to resume but fails since it doesn't
get the RX interrupt from FW indicating that d0i3 exit was completed.
Fix it by adding an explicit call to enable interrupts.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

My patch resized the pool size, but neglected to resize
the global table, which is obviously wrong since the global
table maps the pool's rxb to vid one to one. This results
in a panic in 9000 devices.
Add a build bug to avoid such a case in the future.

Fixes: 7b542436

 ("iwlwifi: pcie: fine tune number of rxbs")
Reported-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Add debugfs entry named lqm_send_cmd for kicking a
measurement. This hook takes the duration and the timeout
as parameter.
Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

LQM stands for Link Quality Measurement. The firmware
will collect a defined set of statitics (see the
notification for details) that allow to know how busy
the medium is. The driver issues a request to the firmware
that includes the duration of the measurement (the firmware
needs to be on channel for that amount of time) and the
timeout (in case the firmware has a lot of offchannel
activities). If the timeout elapses, the firmware will
send partial results which are still valuable.
In case of disassociation / channel switch and alike, the
driver is in charge of stopping the measurements and the
firmware will reply with partial results.

The user space API for now is debugfs only and will be
implmemented in an upcoming patch.
Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

In case of FW error, support dumping the UMAC internal txfifos.
To do so, support version 2 of shared memory cfg command, which
contains the sizes of the internal txfifos, and move the command
to the system group.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Paging contains 3 sections in the fw. The first for the paging separator,
The second for the CSS block, the third with the paging data.

Currently if the driver finds the paging separator, and there is only
section left (CSS), once reading the CSS section, the driver will
attempt to read the paging data and will go out of the arrays bounds.

Make sure that the FW image contains the right amount of sections for
paging.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Currently the driver has 2 buffers for paging:
1. paging db - this contains all of the pages that were in the FW
image, that the driver stores for the FW. This is allocated for each
block separately (not contiguous).
2. download buffer - we need to provide this empty buffer for the
iwl_sdio_load_fw_chunk function to copy the requested pages to the shared
memory. This is one big buffer of contiguous memory whose size is the
size of all the blocks that the fw paging section can contain.

This download buffer size is too big, and causes the allocation to fail
sometimes. Since the driver allocates memory for each block separately,
it is not possible for the FW to request all of the pages in one request
(the FW gives an address and size, so blocks need to be contiguous for
this to happen), therefore the FW is limited to request only one block.

Decrease the size of the paging download buffer to be the size of a
paging block.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Currently when stop flow is performed, there might be transport TX RTPM
references that are not freed in case we unmap a queue that still has
packets not reclaimed. Fix that.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Pull networking updates from David Miller:
 "Highlights:

   1) Support more Realtek wireless chips, from Jes Sorenson.

   2) New BPF types for per-cpu hash and arrap maps, from Alexei
      Starovoitov.

   3) Make several TCP sysctls per-namespace, from Nikolay Borisov.

   4) Allow the use of SO_REUSEPORT in order to do per-thread processing
   of incoming TCP/UDP connections.  The muxing can be done using a
   BPF program which hashes the incoming packet.  From Craig Gallek.

   5) Add a multiplexer for TCP streams, to provide a messaged based
      interface.  BPF programs can be used to determine the message
      boundaries.  From Tom Herbert.

   6) Add 802.1AE MACSEC support, from Sabrina Dubroca.

   7) Avoid factorial complexity when taking down an inetdev interface
      with lots of configured addresses.  We were doing things like
      traversing the entire address less for each address removed, and
      flushing the entire...

Pull cgroup updates from Tejun Heo:
 "cgroup changes for v4.6-rc1.  No userland visible behavior changes in
  this pull request.  I'll send out a separate pull request for the
  addition of cgroup namespace support.

   - The biggest change is the revamping of cgroup core task migration
     and controller handling logic.  There are quite a few places where
     controllers and tasks are manipulated.  Previously, many of those
     places implemented custom operations for each specific use case
     assuming specific starting conditions.  While this worked, it makes
     the code fragile and difficult to follow.

     The bulk of this pull request restructures these operations so that
     most related operations are performed through common helpers which
     implement recursive (subtrees are always processed consistently)
     and idempotent (they make cgroup hierarchy converge to the target
     state rather than performi...