Merge branches 'pci/host-aardvark', 'pci/host-altera', 'pci/host-dra7xx', 'pci/host-hv', 'pci/host-vmd' and 'pci/host-xilinx' into next

* pci/host-aardvark:
  arm64: dts: marvell: Add Aardvark PCIe support for Armada 3700
  PCI: aardvark: Add Aardvark PCI host controller driver
  dt-bindings: add DT binding for the Aardvark PCIe controller

* pci/host-altera:
  PCI: altera: Poll for link up status after retraining the link
  PCI: altera: Check link status before retrain link
  PCI: altera: Reorder read/write functions

* pci/host-dra7xx:
  PCI: dra7xx: Fix return value in case of error

* pci/host-hv:
  PCI: hv: Fix interrupt cleanup path
  PCI: hv: Handle all pending messages in hv_pci_onchannelcallback()
  PCI: hv: Don't leak buffer in hv_pci_onchannelcallback()

* pci/host-vmd:
  x86/PCI: VMD: Separate MSI and MSI-X vector sharing
  x86/PCI: VMD: Use x86_vector_domain as parent domain
  x86/PCI: VMD: Use lock save/restore in interrupt enable path
  x86/PCI: VMD: Initialize list item in IRQ disable
  x86/PCI: VMD: Select device dma ops to override

* pci/host-xilinx:
  PCI: xilinx: Fix return value in case of error

Manually apply changes from pci/demodularize-hosts and
pci/host-request-windows to drivers/pci/host/pci-aardvark.c

* pci/host-tegra:
  PCI: tegra: Program PADS_REFCLK_CFG* registers with per-SoC values
  PCI: tegra: Program PADS_REFCLK_CFG* always, not just on legacy SoCs
  PCI: tegra: Stop setting pcibios_min_mem
  PCI: tegra: Use generic pci_remap_iospace() rather than ARM32-specific one
  PCI: tegra: Use lower-case hex consistently for register definitions

Conflicts:
	drivers/pci/host/pci-tegra.c

Drop stray pci_ioremap_io() per Thierry Reding <treding@nvidia.com>;
removal tested by Jon Hunter <jonathanh@nvidia.com>.

* pci/demodularize-hosts:
  PCI: xgene: Make explicitly non-modular
  PCI: thunder-pem: Make explicitly non-modular
  PCI: thunder-ecam: Make explicitly non-modular
  PCI: tegra: Make explicitly non-modular
  PCI: rcar-gen2: Make explicitly non-modular
  PCI: rcar: Make explicitly non-modular
  PCI: mvebu: Make explicitly non-modular
  PCI: layerscape: Make explicitly non-modular
  PCI: keystone: Make explicitly non-modular
  PCI: hisi: Make explicitly non-modular
  PCI: generic: Make explicitly non-modular
  PCI: designware-plat: Make it explicitly non-modular
  PCI: artpec6: Make explicitly non-modular
  PCI: armada8k: Make explicitly non-modular
  PCI: artpec: Add PCI_MSI_IRQ_DOMAIN dependency
  PCI: artpec: Add Axis ARTPEC-6 PCIe controller driver
  PCI: Add DT binding for Axis ARTPEC-6 PCIe controller
  PCI: generic: Select IRQ_DOMAIN

* pci/host-request-windows:
  PCI: versatile: Simplify host bridge window iteration
  PCI: versatile: Request host bridge window resources with core function
  PCI: tegra: Request host bridge window resources with core function
  PCI: tegra: Remove top-level resource from hierarchy
  PCI: rcar: Simplify host bridge window iteration
  PCI: rcar: Request host bridge window resources with core function
  PCI: rcar Gen2: Request host bridge window resources
  PCI: rcar: Drop gen2 dummy I/O port region
  ARM: Make PCI I/O space optional
  PCI: mvebu: Request host bridge window resources with core function
  PCI: generic: Simplify host bridge window iteration
  PCI: generic: Request host bridge window resources with core function
  PCI: altera: Simplify host bridge window iteration
  PCI: altera: Request host bridge window resources with core function
  PCI: xilinx-nwl: Use dev_printk() when possible
  PCI: xilinx-nwl: Request host bridge window resources
  PCI: xilinx-nwl: Free bridge resource list on failure
  PCI: xilinx: Request host bridge window resources
  PCI: xilinx: Free bridge resource list on failure
  PCI: xgene: Request host bridge window resources
  PCI: xgene: Free bridge resource list on failure
  PCI: iproc: Request host bridge window resources
  PCI: designware: Simplify host bridge window iteration
  PCI: designware: Request host bridge window resources
  PCI: designware: Free bridge resource list on failure
  PCI: Add devm_request_pci_bus_resources()

* pci/resource:
  unicore32/PCI: Remove pci=firmware command line parameter handling
  ARM/PCI: Remove arch-specific pcibios_enable_device()
  ARM64/PCI: Remove arch-specific pcibios_enable_device()
  MIPS/PCI: Claim bus resources on PCI_PROBE_ONLY set-ups
  ARM/PCI: Claim bus resources on PCI_PROBE_ONLY set-ups
  PCI: generic: Claim bus resources on PCI_PROBE_ONLY set-ups
  PCI: Add generic pci_bus_claim_resources()
  alx: Use pci_(request|release)_mem_regions
  ethernet/intel: Use pci_(request|release)_mem_regions
  GenWQE: Use pci_(request|release)_mem_regions
  lpfc: Use pci_(request|release)_mem_regions
  NVMe: Use pci_(request|release)_mem_regions
  PCI: Add helpers to request/release memory and I/O regions
  PCI: Extending pci=resource_alignment to specify device/vendor IDs
  sparc/PCI: Implement pci_resource_to_user() with pcibios_resource_to_bus()
  powerpc/pci: Implement pci_resource_to_user() with pcibios_resource_to_bus()
  microblaze/PCI: Implement pci_resource_to_user() with pcibios_resource_to_bus()
  PCI: Unify pci_resource_to_user() declarations
  microblaze/PCI: Remove useless __pci_mmap_set_pgprot()
  powerpc/pci: Remove __pci_mmap_set_pgprot()
  PCI: Ignore write combining when mapping I/O port space

Merge branches 'pci/aspm', 'pci/dpc', 'pci/hotplug', 'pci/misc', 'pci/msi', 'pci/pm' and 'pci/virtualization' into next

* pci/aspm:
  PCI/ASPM: Remove redundant check of pcie_set_clkpm

* pci/dpc:
  PCI: Remove DPC tristate module option
  PCI: Bind DPC to Root Ports as well as Downstream Ports
  PCI: Fix whitespace in struct dpc_dev
  PCI: Convert Downstream Port Containment driver to use devm_* functions

* pci/hotplug:
  PCI: Allow additional bus numbers for hotplug bridges

* pci/misc:
  PCI: Include <asm/dma.h> for isa_dma_bridge_buggy
  PCI: Make bus_attr_resource_alignment static
  MAINTAINERS: Add file patterns for PCI device tree bindings
  PCI: Fix comment typo

* pci/msi:
  PCI/MSI: irqchip: Fix PCI_MSI dependencies

* pci/pm:
  PCI: pciehp: Ignore interrupts during D3cold
  PCI: Document connection between pci_power_t and hardware PM capability
  PCI: Add runtime PM support for PCIe ports
  ACPI / hotplug / PCI: Runtime resume bridge before rescan
  PCI: Power on bridges before scanning new devices
  PCI: Put PCIe ports into D3 during suspend
  PCI: Don't clear d3cold_allowed for PCIe ports
  PCI / PM: Enforce type casting for pci_power_t

* pci/virtualization:
  PCI: Add ACS quirk for Solarflare SFC9220
  PCI: Add DMA alias quirk for Adaptec 3805
  PCI: Mark Atheros AR9485 and QCA9882 to avoid bus reset
  PCI: Add function 1 DMA alias quirk for Marvell 88SE9182

* pci/arm64-acpi:
  ARM64: PCI: Support ACPI-based PCI host controller
  ARM64: PCI: Implement AML accessors for PCI_Config region
  ARM64: PCI: ACPI support for legacy IRQs parsing and consolidation with DT code
  ARM64: PCI: Add acpi_pci_bus_find_domain_nr()
  PCI: Factor DT-specific pci_bus_find_domain_nr() code out
  PCI: Refactor pci_bus_assign_domain_nr() for CONFIG_PCI_DOMAINS_GENERIC
  PCI/ACPI: Add generic MCFG table handling
  PCI/ACPI: Support I/O resources when parsing host bridge resources
  PCI: Add pci_unmap_iospace() to unmap I/O resources
  PCI: Add parent device field to ECAM struct pci_config_window
  PCI: Move ecam.h to linux/include/pci-ecam.h

This code is not being built as a module by anyone:

  drivers/pci/host/Kconfig:config PCI_XGENE
  drivers/pci/host/Kconfig:       bool "X-Gene PCIe controller"

Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.

Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.

[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Tanmay Inamdar <tinamdar@apm.com>

This code is not being built as a module by anyone:

  drivers/pci/host/Kconfig:config PCI_HOST_THUNDER_PEM
  drivers/pci/host/Kconfig:       bool "Cavium Thunder PCIe controller to off-chip devices"

Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.

Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.

Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: David Daney <david.daney@cavium.com>

This code is not being built as a module by anyone:

  drivers/pci/host/Kconfig:config PCI_HOST_THUNDER_ECAM
  drivers/pci/host/Kconfig:       bool "Cavium Thunder ECAM controller to on-chip devices on pass-1.x silicon"

Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.

Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.

Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: David Daney <david.daney@cavium.com>

This code is not being built as a module by anyone:

  drivers/pci/host/Kconfig:config PCI_TEGRA
  drivers/pci/host/Kconfig:       bool "NVIDIA Tegra PCIe controller"

Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.

Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.

Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Stephen Warren <swarren@wwwdotorg.org>
CC: Alexandre Courbot <gnurou@gmail.com>
CC: linux-tegra@vger.kernel.org

This code is not being built as a module by anyone:

  drivers/pci/host/Kconfig:config PCI_RCAR_GEN2
  drivers/pci/host/Kconfig:       bool "Renesas R-Car Gen2 Internal PCI controller"

Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.

Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.

Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

[bhelgaas: changelog, remove "Module" from author comment]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Phil Edworthy <phil.edworthy@renesas.com>
CC: Valentine Barshak <valentine.barshak@cogentembedded.com>

This code is not being built as a module by anyone:

  drivers/pci/host/Kconfig:config PCI_RCAR_GEN2_PCIE
  drivers/pci/host/Kconfig:       bool "Renesas R-Car PCIe controller"

Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.

Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.

Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

[bhelgaas: changelog, remove "Module" from author comment]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Phil Edworthy <phil.edworthy@renesas.com>

This code is not being built as a module by anyone:

  drivers/pci/host/Kconfig:config PCI_MVEBU
  drivers/pci/host/Kconfig:       bool "Marvell EBU PCIe controller"

Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.

Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.

Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

[bhelgaas: changelog, remove "Module" from author comment]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
CC: Jason Cooper <jason@lakedaemon.net>

This code is not being built as a module by anyone:

  drivers/pci/host/Kconfig:config PCI_LAYERSCAPE
  drivers/pci/host/Kconfig:       bool "Freescale Layerscape PCIe controller"

Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.

Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.

Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Minghuan Lian <minghuan.Lian@freescale.com>
CC: Mingkai Hu <mingkai.hu@freescale.com>
CC: Roy Zang <tie-fei.zang@freescale.com>

This code is not being built as a module by anyone:

  drivers/pci/host/Kconfig:config PCI_KEYSTONE
  drivers/pci/host/Kconfig:       bool "TI Keystone PCIe controller"

Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.

Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.

Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-By: Murali Karicheri <m-karicheri2@ti.com>

This code is not being built as a module by anyone:

  host/Kconfig:config PCI_HISI
  host/Kconfig:    bool "HiSilicon Hip05 and Hip06 SoCs PCIe controllers"

Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.

Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.

Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Zhou Wang <wangzhou1@hisilicon.com>
CC: Dacai Zhu <zhudacai@hisilicon.com>
CC: Gabriele Paoloni <gabriele.paoloni@huawei.com>

This code is not being built as a module by anyone:

  drivers/pci/host/Kconfig:config PCI_HOST_GENERIC
  drivers/pci/host/Kconfig:       bool "Generic PCI host controller"

Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.

Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.

Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Will Deacon <will.deacon@arm.com>

This code is not being built as a module by anyone:

  drivers/pci/host/Kconfig:config PCIE_DW_PLAT
  drivers/pci/host/Kconfig:       bool "Platform bus based DesignWare PCIe Controller"

Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.

Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.

Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Joao Pinto <jpinto@synopsys.com>
CC: Jingoo Han <jingoohan1@gmail.com>
CC: Pratyush Anand <pratyush.anand@gmail.com>

This code is not being built as a module by anyone:

  drivers/pci/host/Kconfig:config PCIE_ARTPEC6
  drivers/pci/host/Kconfig:       bool "Axis ARTPEC-6 PCIe controller"

Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.

Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.

Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

[bhelgaas: changelog, add "Author" comment]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Niklas Cassel <niklas.cassel@axis.com>
CC: Jesper Nilsson <jesper.nilsson@axis.com>

This code is not being built as a module by anyone:

  drivers/pci/host/Kconfig:config PCIE_ARMADA_8K
  drivers/pci/host/Kconfig:       bool "Marvell Armada-8K PCIe controller"

Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.

Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.

Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>

* pci/host-artpec:
  PCI: artpec: Add PCI_MSI_IRQ_DOMAIN dependency
  PCI: artpec: Add Axis ARTPEC-6 PCIe controller driver
  PCI: Add DT binding for Axis ARTPEC-6 PCIe controller

* pci/host-generic:
  PCI: generic: Select IRQ_DOMAIN

The DesignWare PCIe driver requires MSI support, so we get a warning for
the artpec6 glue driver if that is not enabled:

  warning: (PCIE_ARTPEC6) selects PCIE_DW which has unmet direct dependencies (PCI && PCI_MSI_IRQ_DOMAIN)

Add the same dependency that all other such drivers have.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Niklas Cassel <niklas.cassel@axis.com>

The Solarflare SFC9220 apparently lacks an ACS capability, but does not
perform peer-to-peer between functions.  Add a quirk so we know about this
isolation.

[bhelgaas: changelog]
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Add the SoC-level description of the PCIe controller found on the Marvell
Armada 3700 and enable this PCIe controller on the development board for
this SoC.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Add a driver for the Aardvark PCIe controller used on the Marvell Armada
3700 ARM64 SoC.

Based on work done by Hezi Shahmoon <hezi.shahmoon@marvell.com> and Marcin
Wojtas <mw@semihalf.com>.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Add the documentation for the Device Tree binding for the Aardvark PCIe
controller, found on Marvell Armada 3700 ARM64 SoCs.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

The value that should be programmed into the PADS_REFCLK register varies
per SoC.  Fix the Tegra PCIe driver to program the correct values.  Future
SoCs will require different values in cfg0/1, so the two values are stored
separately in the per-SoC data structures.

For reference, the values are all documented in NV bug 1771116 comment 20.
The ASIC team has validated all these values, except for the Tegra20 value
which is simply left unchanged in this patch.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thierry Reding <treding@nvidia.com>

tegra_pcie_phy_power_on() calls tegra_pcie_phy_enable() only for legacy
SoCs.  However, part of tegra_pcie_phy_enable() needs to happen in all
cases.  Move that code up one level into tegra_pcie_phy_power_on().

[bhelgaas: changelog]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

pcibios_min_mem only exists on 32-bit ARM, so using it in pci-tegra.c
prevents the driver from being used on other arches.

In __pci_assign_resource(), we clip the available area based on
PCIBIOS_MIN_MEM.  On 32-bit ARM, this is pcibios_min_mem, with a default
value of 0x01000000.  For Tegra, we discover the space available for PCI
resource allocation from the device tree, and the lowest address that will
ever be available is 0x12000000 (on Tegra124).

The Tegra windows are always higher than the default pcibios_min_mem, so
the __pci_assign_resource() has no effect, so there's no need to adjust
pcibios_min_mem here.

[bhelgaas: changelog]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Use the pci_remap_iospace() function provided by the PCI core, rather
than the 32-bit ARM-specific pci_ioremap_io().
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Most of the register definitions use lowercase hexadecimal values, with a
few exceptions using uppercase.  Convert the latter to be more in line with
the former.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

A user may hot add a switch requiring more than one bus to enumerate.  This
previously required a system reboot if BIOS did not sufficiently pad the
bus resource, which they frequently don't do.

Add a kernel parameter so a user can specify the minimum number of bus
numbers to reserve for a hotplug bridge's subordinate buses so rebooting
won't be necessary.

The default is 1, which is equivalent to previous behavior.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Change the Downstream Port Containment config type from tristate to bool.

The driver doesn't automatically load based on any rules, so it needs to be
built-in in order to bind to devices it needs to drive.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

PCIe port type values are not flags, so OR'ing them is not correct.
Previously the result was equivalent to PCIe Downstream Ports, so we were
missing binding to DPC-capable Root Ports.

Change the type to 'any' so we can bind to both port types.  While this
will cause the code to check Upstream Ports, the driver won't claim them
since they are not DPC-capable.
Reported-by: Alexander Antonov <alexanderx.v.antonov@intel.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Mika Westerberg <mika.westerberg@linux.intel.com>

SR-IOV disabled from the host causes a memory leak.  pci-hyperv usually
first receives a PCI_EJECT notification and then proceeds to delete the
hpdev list entry in hv_eject_device_work().  Later in hv_msi_free() since
the device is no longer on the device list hpdev is NULL and hv_msi_free
returns without freeing int_desc as part of hv_int_desc_free().
Signed-off-by: Cathy Avery <cavery@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jake Oshins <jakeo@microsoft.com>

In dra7xx_pcie_init_irq_domain(), the pattern used to check and return
error is:

   if (!var) {
      dev_err(...);
      return PTR_ERR(var);
   }

So the returned value in case of error is always 0, which means 'success'.
Change it to return -ENODEV instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>

In xilinx_pcie_init_irq_domain(), the pattern used to check and return
error is:

   if (!var) {
      dev_err(...);
      return PTR_ERR(var);
   }

So the returned value in case of error is always 0, which means 'success'.
Change it to return -ENODEV instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>

Some PCIe devices take a long time to reach link up state after retrain.
Poll for link up status after retraining the link.  This is to make sure
the link is up before we access configuration space.

[bhelgaas: changelog]
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Check the link status before retraining.  If the link is not up, don't
bother trying to retrain it.

[bhelgaas: split code move to separate patch, changelog]
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Move cra_writel(), cra_readl(), and altera_pcie_link_is_up() so a future
patch can use them in altera_pcie_retrain().  No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>