- 30 May, 2017 19 commits
-
-
David Ahern authored
Fill in extack for errors in build_state for mpls lwt encap including passing extack to nla_get_labels and adding error messages for failures in it. Signed-off-by:
David Ahern <dsahern@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David Ahern authored
Pass extack arg down to lwtunnel_build_state and the build_state callbacks. Add messages for failures in lwtunnel_build_state, and add the extarg to nla_parse where possible in the build_state callbacks. Signed-off-by:
-
David Ahern authored
Pass extack down to lwtunnel_valid_encap_type and lwtunnel_valid_encap_type_attr. Add messages for unknown or unsupported encap types. Signed-off-by:
-
David Ahern authored
Add extack error message for invalid prefix length and invalid prefix. Example of the latter is a route spec containing 172.16.100.1/24, where the /24 mask means the lower 8-bits should be 0. Amazing how easy that one is to overlook when an EINVAL is returned. Signed-off-by:
-
David Ahern authored
fib_table_insert and fib_table_delete have the same checks on the prefix and length. Refactor into a helper. Avoids duplicate extack messages in the next patch. Signed-off-by:
-
David S. Miller authored
Jakub Kicinski says: ==================== nfp: pci core, hwmon, live mac addr change This series brings updates to core PCI code, SR-IOV, exposes firmware's capability to change MAC address at runtime and HWMON interfaces. The PCI code updates include resiliency improvement in conditions which are quite unusual, but still shouldn't make the driver oops. We also handle very large device memory operation more gracefully. A timeout is added to acquiring mutexes in device memory. Pablo provides a patch to expose to the stack the ability to change MAC addresses under traffic while David adds HWMON interface for reading device temperature and power consumption. Last three patches are minor improvements to the netdev code. v2: - add patch 1 - fix for devlink build; - fix build issue with the hwmon patch. ==================== Signed-off-by: -
Jakub Kicinski authored
We only kick RX free buffer queue controller every NFP_NET_FL_BATCH (currently 16) entries. This means that we will always kick the QC when write ring index is divisable by NFP_NET_FL_BATCH. There is no need to keep counts. Signed-off-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by:
-
Jakub Kicinski authored
Adding ring size to index calculation is pointless, since index will be masked with ring size - 1. Suggested-by:
David Laight <David.Laight@ACULAB.COM> Signed-off-by:
-
Jakub Kicinski authored
Ring pointers are unsigned. Fix the print formats to avoid showing users negative values. Signed-off-by:
-
Jakub Kicinski authored
There is currently no timeout to the resource and lock acquiring loops. We printed warnings and depended on user sending a signal to the waiting process to stop the waiting. This doesn't work very well when wait happens out of a work queue. The simplest example of that is PCI probe. When user loads the module and card is in a broken state modprobe will wait forever and signals sent to it will not actually reach the probing thread. Make sure all wait loops have a time out. Set the upper wait time to 60 seconds to stay on the safe side. Signed-off-by:
-
David Brunecz authored
Add support for retrieving temperature and power sensor and limits via NSP. Signed-off-by:
David Brunecz <david.brunecz@netronome.com> Signed-off-by:
-
Jakub Kicinski authored
We want to support extendable commands, where newer versions of the management FW may provide more information. Zero out the communication buffer before passing control to NSP. This way if management FW is old and only fills in first N bytes, the remaining ones will be zeros which extended ABI fields should reserve as not supported/not available. Signed-off-by:
-
Jakub Kicinski authored
We currently print reserved BAR mappings info as we create them. This makes the probe logs longer than necessary. Print into a buffer instead and log all the info as a single line. Signed-off-by:
-
Jakub Kicinski authored
nfp_cpp_{read,write}() helpers perform device memory mapping (setting the PCIe -> NOC translation BARs) and accessing it. They, however, currently implicitly expect that the length of entire operation will fit in one BAR translation window. There is a number of 16MB windows available, and we don't really need to access such large areas today. If the user, however, manages to trick the driver into making a big mapping (e.g. by providing a huge fake FW file), the driver will print a warning saying "No suitable BAR found for request" and a stack trace - which most users find concerning. To be future-proof and not scare users with warnings, make the nfp_cpp_{read,write}() helpers do accesses chunk by chunk if the area size is large. Set the notion of "large" to 2MB, which is the size of the smallest BAR window. Signed-off-by: -
Jakub Kicinski authored
For accessing PCIe ctrl memory we depend on the BAR aperture being large enough to reach all registers. Since the BAR aperture can be set in the flash make sure the driver won't oops the kernel when the PCIe configuration is unusual. Signed-off-by:
-
Jakub Kicinski authored
If ioremap of PCIe ctrl memory failed we can still get to it through PCI config space, therefore we allow ioremap() to fail. When if fails, however, we must leave all the IOMEM pointers as NULL. Currently we would calculate csr and em pointers, adding offsets to the potential NULL value and therefore making the NULL-checks throughout the code ineffective. Signed-off-by:
-
Jakub Kicinski authored
PCI subsystem has support for drivers limiting the number of VFs available below what the IOV capability claims. Make use of it. While at it remove the #ifdef/#endif on CONFIG_PCI_IOV, it was there to avoid unnecessary warnings in case device read failed but kernel doesn't have SR-IOV support anyway. Device reads should not fail. Note that we still need the driver-internal check for the case where max VFs is 0 since PCI subsystem treats 0 as limit not set. Signed-off-by:
-
Pablo Cascón authored
Expose FW app ability to change MAC address at runtime. Make sure we only depend on it if FW app advertised the right capability. Signed-off-by:
Pablo Cascón <pablo.cascon@netronome.com> Reviewed-by:
-
Jakub Kicinski authored
Fix build with DEVLINK=m and NFP=y. Fixes: 1851f93f ("nfp: add devlink support") Reported-by:
kbuild test robot <fengguang.wu@intel.com> Signed-off-by:
-
- 27 May, 2017 6 commits
-
-
Florian Fainelli authored
Some Ethernet drivers will attach/connect to a PHY device before calling register_netdevice() which is responsible for calling netdev_register_kobject() which would do the network device's kobject initialization. In such a case, sysfs_create_link() would return -ENOENT because the network device's kobject is not ready yet, and we would fail to connect to the PHY device. In order to keep things simple and symetrical, we just take the success path as indicative of the ability to access the network device's kobject, and create the second link if that's the case. Fixes: 5568363f ("net: phy: Create sysfs reciprocal links for attached_dev/phydev") Reported-by:
Woojung Hung <Woojung.Huh@microchip.com> Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Vivien Didelot authored
mv88e6xxx_serdes_power returns an error, so no need to print an error message inside of it. Rather print it in its caller when the error is ignored, which is in the mv88e6xxx_port_disable void function. Catch and return its error in the counterpart mv88e6xxx_port_enable. Fixes: 04aca993 ("dsa: mv88e6xxx: Enable/Disable SERDES on port enable/disable") Signed-off-by:
Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by:
-
David S. Miller authored
Vladislav Yasevich says: ==================== rtnetlink: Updates to rtnetlink_event() First is the patch to add IFLA_EVENT attribute to the netlink message. It supports only currently white-listed events. Like before, this is just an attribute that gets added to the rtnetlink message only when the messaged was generated as a result of a netdev event. In my case, this is necessary since I want to trap NETDEV_NOTIFY_PEERS event (also possibly NETDEV_RESEND_IGMP event) and perform certain actions in user space. This is not possible since the messages generated as a result of netdev events do not usually contain any changed data. They are just notifications. This patch exposes this notification type to userspace. Second, I remove duplicate messages that a result of a change to bonding options. If netlink is used to configure bonding options, 2 messages are generated, one as a result NETDEV_CHANGEINFODATA event triggered by bonding code and one a result of device state changes triggered by netdev_state_change (called from do_setlink). V6: Updated names and refactored to make it less tied to netdev events. (From David Ahern) V5: Rebased. Added iproute2 patch to the series. V4: * Removed the patch the removed NETDEV_CHANGENAME from event whitelist. It doesn't trigger duplicate messages since name changes can only be done while device is down and netdev_state_change() doesn't report changes while device is down. * Added a patch to clean-up duplicate messages on bonding option changes. V3: Rebased. Cleaned-up duplicate event. V2: Added missed events (from David Ahern) ==================== Signed-off-by: -
Vlad Yasevich authored
Whenever a user changes bonding options, a NETDEV_CHANGEINFODATA notificatin is generated which results in a rtnelink message to be sent. While runnig 'ip monitor', we can actually see 2 messages, one a result of the event, and the other a result of state change that is generated bo netdev_state_change(). However, this is not always the case. If bonding changes were done via sysfs or ifenslave (old ioctl interface), then only 1 message is seen. This patch removes duplicate messages in the case of using netlink to configure bonding. It introduceds a separte function that triggers a netdev event and uses that function in the syfs and ioctl cases. This was discovered while auditing all the different envents and continues the effort of cleaning up duplicated netlink messages. CC: David Ahern <dsa@cumulusnetworks.com> CC: Jiri Pirko <jiri@resnulli.us> Signed-off-by:
Vladislav Yasevich <vyasevic@redhat.com> Acked-by:
-
Vlad Yasevich authored
When netdev events happen, a rtnetlink_event() handler will send messages for every event in it's white list. These messages contain current information about a particular device, but they do not include the iformation about which event just happened. So, it is impossible to tell what just happend for these events. This patch adds a new extension to RTM_NEWLINK message called IFLA_EVENT that would have an encoding of event that triggered this message. This would allow the the message consumer to easily determine if it needs to perform certain actions. Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller authored
Overlapping changes in drivers/net/phy/marvell.c, bug fix in 'net' restricting a HW workaround alongside cleanups in 'net-next'. Signed-off-by:
-
- 26 May, 2017 15 commits
-
-
Linus Torvalds authored
Merge tag 'led_fixes_for_4-12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds Pull LED fix from Jacek Anaszewski: "A single LED fix for 4.12-rc3. leds-pca955x driver uses only i2c_smbus API and thus it should pass I2C_FUNC_SMBUS_BYTE_DATA flag to i2c_check_functionality" * tag 'led_fixes_for_4-12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds: leds: pca955x: Correct I2C Functionality
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds authored
Pull networking fixes from David Miller: 1) Fix state pruning in bpf verifier wrt. alignment, from Daniel Borkmann. 2) Handle non-linear SKBs properly in SCTP ICMP parsing, from Davide Caratti. 3) Fix bit field definitions for rss_hash_type of descriptors in mlx5 driver, from Jesper Brouer. 4) Defer slave->link updates until bonding is ready to do a full commit to the new settings, from Nithin Sujir. 5) Properly reference count ipv4 FIB metrics to avoid use after free situations, from Eric Dumazet and several others including Cong Wang and Julian Anastasov. 6) Fix races in llc_ui_bind(), from Lin Zhang. 7) Fix regression of ESP UDP encapsulation for TCP packets, from Steffen Klassert. 8) Fix mdio-octeon driver Kconfig deps, from Randy Dunlap. 9) Fix regression in setting DSCP on ipv6/GRE encapsulation, from Peter Dawson. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits) ipv4: add reference counting to metrics net: ethernet: ax88796: don't call free_irq without request_irq first ip6_tunnel, ip6_gre: fix setting of DSCP on encapsulated packets sctp: fix ICMP processing if skb is non-linear net: llc: add lock_sock in llc_ui_bind to avoid a race condition bonding: Don't update slave->link until ready to commit test_bpf: Add a couple of tests for BPF_JSGE. bpf: add various verifier test cases bpf: fix wrong exposure of map_flags into fdinfo for lpm bpf: add bpf_clone_redirect to bpf_helper_changes_pkt_data bpf: properly reset caller saved regs after helper call and ld_abs/ind bpf: fix incorrect pruning decision when alignment must be tracked arp: fixed -Wuninitialized compiler warning tcp: avoid fastopen API to be used on AF_UNSPEC net: move somaxconn init from sysctl code net: fix potential null pointer dereference geneve: fix fill_info when using collect_metadata virtio-net: enable TSO/checksum offloads for Q-in-Q vlans be2net: Fix offload features for Q-in-Q packets vlan: Fix tcp checksum offloads in Q-in-Q vlans ... -
David S. Miller authored
Nathan Fontenot says: ==================== ibmvnic: Driver updates This set of patches implements several updates to the ibmvnic driver to fix issues that have been found in testing. Most of the updates invovle updating queue handling during driver close and reset operations. ==================== Signed-off-by: -
Nathan Fontenot authored
When the ibmvnic driver is resetting, we can just reset the sub crqs instead of releasing all of their resources and re-allocting them. Signed-off-by:
Nathan Fontenot <nfont@linux.vnet.ibm.com> Signed-off-by:
-
Nathan Fontenot authored
When resetting the ibmvnic driver there is not a need to release and re-allocate the resources for the tx and rx pools. These resources can just be reset to avoid the re-allocations. Signed-off-by:
-
Nathan Fontenot authored
When a driver reset operation occurs there is not a need to release the CRQ resources and re-allocate them. Instead a reset of the CRQ will suffice. Signed-off-by:
-
Nathan Fontenot authored
We do not want to process any receive frames if the ibmvnic_poll routine is invoked while a reset is in process. Also, before replenishing the rx pools in the ibmvnic_poll, we want to make sure the adapter is not in the process of closing. Signed-off-by:
-
Thomas Falcon authored
If H_CLOSED is returned, halt RX buffer replenishment activity until firmware sends a notification that the driver can reset. Signed-off-by:
Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by:
-
Thomas Falcon authored
This patch disables transmissions and reports carrier off if xmit function returns that the hardware TX queue is closed. The driver can then await a signal from firmware to determine the correct reset method. Signed-off-by:
-
John Allen authored
Handle non-fatal error conditions. The process to do this when resetting the driver is to just do __ibmvnic_close followed by __ibmvnic_open. Signed-off-by:
John Allen <jallen@linux.vnet.ibm.com> Signed-off-by:
-
Thomas Falcon authored
A race condition occurs when closing the driver. Free'ing of skb's can race between the close routine and ibmvnic_tx_interrupt. To fix this we move the claenup of tx pools during close to after the sub-CRQ interrupts are disabled. Signed-off-by:
-
John Allen authored
Send gratuitous arp after any reset. Signed-off-by:
-
John Allen authored
Handle case where phyp sends a failover after failing to send the init crq. Signed-off-by:
-
John Allen authored
Track the state of ibmvnic napis. The driver can get into states where it can be reset when napis are already disabled and attempting to disable them again will cause the driver to hang. Signed-off-by:
-
David S. Miller authored
Jiri Pirko says: ==================== mlxsw: Improve extensibility Ido says: Since the initial introduction of the bridge offload in commit 56ade8fe ("mlxsw: spectrum: Add initial support for Spectrum ASIC") the per-port struct was used to store both physical properties of the port as well as logical bridge properties such as learning and active VLANs in the VLAN-aware bridge. The above resulted in a bloated struct and code that is getting increasingly difficult to extend when stacked devices are taken into account as well as more advanced use cases such as IGMP snooping. Due to the incremental development nature of this driver as well as the complexity of the underlying hardware, subsequent design decisions failed to generalize the FID and RIF resources, which could've benefited from a more generic design, resulting in consolidated code paths and better extensibility with regards to future ASICs and use cases. This patchset tries to solve both of these design problems, as they're tightly coupled. To ease the code review, the changes are done in a bottom-up manner, in which the port struct is the first to be patched, then the FIDs the ports are mapped to and finally the RIFs configured on top. The first half of the patchset gradually moves away from the previous design to a design that is more in sync with the underlying hardware and which clearly separates between hardware-specific structs and logical ones such as a bridge port. All the bridge-specific information is removed from the port struct, as well as the list of VLAN devices ("vPorts") configured on top of it. Instead, a linked list of VLANs is introduced, which allows each VLAN to hold a state, such as mapping to a particular FID and membership in a bridge. The data structures are depicted in the following figure: mlxsw_sp_bridge_device +----------+ | | +----+ | | | | | +----------+ | mlxsw_sp_bridge_port | +----------+ | | | | +--> +-----+--> .. | | | | +----+-----+ | | | v | mlxsw_sp_bridge_vlan | +----------+ | | vid X | | | +--> .. | | | | +----+-----+ | | +--+----v-----+ | vid X | +--+ +--> .. | | | mlxsw_sp_port | +----------+ +----------+ | mlxsw_sp_port_vlan | | | | +--+ | | +----------+ This model allows us to consolidate many of the code paths relating to VLAN-aware and VLAN-unaware bridges, as the latter is simply represented using a bridge port with a VLAN list size of one. Another advantage of the model is that it's easy to extend it with future per-VLAN attributes - such as mrouter indication - by merely pushing these down from the bridge port struct to the bridge VLAN one. The second half of the patchset builds on top of previous work and prepares the driver for the common FID and RIF cores, which are finally implemented in the last two patches. These exploit the fact that despite the different kinds of FIDs and RIFs, they do share a common object on which the core operations can operate on. By hiding both objects from the rest of the driver and modeling their operations using a VFT, it'll be easier to extend the driver for future use cases such as VXLAN. Tested using following LNST recipes: https://github.com/jpirko/lnst/tree/master/recipes/switchdev ==================== Signed-off-by:
-
