commit 1245374e upstream.

At xhci removal the USB3 hcd (shared_hcd) is removed before the primary
USB2 hcd. Interrupts for port status changes may still occur for USB3
ports after the shared_hcd is freed, causing  NULL pointer dereference.

Check if xhci->shared_hcd is still valid before handing USB3 port events

Cc: <stable@vger.kernel.org>
Reported-by: Peter Chen <peter.chen@nxp.com>
Tested-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f0680904 upstream.

Ensure that the shared_hcd pointer is valid when calling usb_put_hcd()

The shared_hcd is removed and freed in xhci by first calling
usb_remove_hcd(xhci->shared_hcd), and later
usb_put_hcd(xhci->shared_hcd)

Afer commit fe190ed0 ("xhci: Do not halt the host until both HCD have
disconnected their devices.") the shared_hcd was never properly put as
xhci->shared_hcd was set to NULL before usb_put_hcd(xhci->shared_hcd) was
called.

shared_hcd (USB3) is removed before primary hcd (USB2).
While removing the primary hcd we might need to handle xhci interrupts
to cleanly remove last USB2 devices, therefore we need to set
xhci->shared_hcd to NULL before removing the primary hcd to let xhci
interrupt handler know shared_hcd is no longer available.

xhci-plat.c, xhci-histb.c and xhci-mtk first create both their hcd's before
adding them. so to keep the correct reverse removal order use a temporary
shared_hcd variable for them.
For more details see commit 4ac53087 ("usb: xhci: plat: Create both
HCDs before adding them")

Fixes: fe190ed0 ("xhci: Do not halt the host until both HCD have disconnected their devices.")
Cc: Joel Stanley <joel@jms.id.au>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Jianguo Sun <sunjianguo1@huawei.com>
Cc: <stable@vger.kernel.org>
Reported-by: Jack Pham <jackp@codeaurora.org>
Tested-by: Jack Pham <jackp@codeaurora.org>
Tested-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 7b412b04 upstream.

In dwc3_pci_quirks() function, gpiod lookup table is only registered for
baytrail SOC. But in dwc3_pci_remove(), we try to unregistered it
without any checks. This leads to NULL pointer de-reference exception in
gpiod_remove_lookup_table() when unloading the module for non baytrail
SOCs. This patch fixes this issue.

Fixes: 5741022c ("usb: dwc3: pci: Add GPIO lookup table on platforms
without ACPI GPIO resources")
Cc: <stable@vger.kernel.org>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 08fd9a82 upstream.

If dwc3_core_init_mode() fails with deferred probe,
next probe fails on sysfs with

sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:11.0/dwc3.0.auto/dwc3.0.auto.ulpi'

To avoid this failure, clean up ULPI device.

Cc: <stable@vger.kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ba3a51ac upstream.

Current check for the last extra TRB for zero and unaligned transfers
does not account for isoc OUT. The last TRB of the Buffer Descriptor for
isoc OUT transfers will be retired with HWO=0. As a result, we won't
return early. The req->remaining will be updated to include the BUFSIZ
count of the extra TRB, and the actual number of transferred bytes
calculation will be wrong.

To fix this, check whether it's a short or zero packet and the last TRB
chain bit to return early.

Fixes: c6267a51 ("usb: dwc3: gadget: align transfers to wMaxPacketSize")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 2fc6d4be upstream.

When chaining ISOC TRBs together, only the first ISOC TRB should be of
type ISOC_FIRST, all others should be of type ISOC. This patch fixes
that.

Fixes: c6267a51 ("usb: dwc3: gadget: align transfers to wMaxPacketSize")
Cc: <stable@vger.kernel.org> # v4.11+
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 22454b79 upstream.

This will clear the USB_PORT_FEAT_C_CONNECTION bit in case of a hub port reset
only if a device is was attached to the hub port before resetting the hub port.

Using a Lenovo T480s attached to the ultra dock it was not possible to detect
some usb-c devices at the dock usb-c ports because the hub_port_reset code
will clear the USB_PORT_FEAT_C_CONNECTION bit after the actual hub port reset.
Using this device combo the USB_PORT_FEAT_C_CONNECTION bit was set between the
actual hub port reset and the clear of the USB_PORT_FEAT_C_CONNECTION bit.
This ends up with clearing the USB_PORT_FEAT_C_CONNECTION bit after the
new device was attached such that it was not detected.

This patch will not clear the USB_PORT_FEAT_C_CONNECTION bit if there is
currently no device attached to the port before the hub port reset.
This will avoid clearing the connection bit for new attached devices.
Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 41f1c484 upstream.

When building with CONFIG_EFI and CONFIG_EFI_STUB on ARM, the libstub
Makefile would use -mno-single-pic-base without checking it was
supported by the compiler. As the ARM (32-bit) clang backend does not
support this flag, the build would fail.

This changes the Makefile to check the compiler's support for
-mno-single-pic-base before using it, similar to c1c38668 ("ARM:
8767/1: add support for building ARM kernel with clang").
Signed-off-by: Alistair Strachan <astrachan@google.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 385a4886 upstream.

Previously, when a HID client such as the Steam Client was running, this
driver disabled its input device to avoid doubling the input events.

While it worked mostly fine, some games got confused by the idle gamepad,
and switched to two player mode, or asked the user to choose which gamepad
to use. Other games just crashed, probably a bug in Unity [1].

With this commit, when a HID client starts, the input device is removed;
when the HID client ends the input device is recreated.

[1]: https://github.com/ValveSoftware/steam-for-linux/issues/5645Signed-off-by: Rodrigo Rivas Costa <rodrigorivascosta@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: Pierre-Loup Griffais <pgriffais@valvesoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 473f0a76 upstream.

According to vendor sdk, vco calibration has to be executed
for each channel configuration whereas mcu calibration has to be
performed during channel scanning. This patch fixes the mt76x0
monitor mode issue since in that configuration vco calibration
was never executed

Fixes: 10de7a8b ("mt76x0: phy files")
Tested-by: Sid Hayn <sidhayn@gmail.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 7e241f64 upstream.

skb_can_coalesce() allows coalescing neighboring slab objects into
a single frag:

  return page == skb_frag_page(frag) &&
         off == frag->page_offset + skb_frag_size(frag);

ceph_tcp_sendpage() can be handed slab pages.  One example of this is
XFS: it passes down sector sized slab objects for its metadata I/O.  If
the kernel client is co-located on the OSD node, the skb may go through
loopback and pop on the receive side with the exact same set of frags.
When tcp_recvmsg() attempts to copy out such a frag, hardened usercopy
complains because the size exceeds the object's allocated size:

  usercopy: kernel memory exposure attempt detected from ffff9ba917f20a00 (kmalloc-512) (1024 bytes)

Although skb_can_coalesce() could be taught to return false if the
resulting frag would cross a slab object boundary, we already have
a fallback for non-refcounted pages.  Utilize it for slab pages too.

Cc: stable@vger.kernel.org # 4.8+
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e82e62e3 upstream.

The PixArt OEM mice are known for disconnecting every minute in
runlevel 1 or 3 if they are not always polled. So add quirk
ALWAYS_POLL for this one as well.

References:
https://www.spinics.net/lists/linux-usb/msg88965.html
http://linet.gr.jp/~kojima/PlamoWeb/ML/htdocs/201808/msg00019.htmlSigned-off-by: Sebastian Parschauer <sparschauer@suse.de>
CC: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit fb862c3b upstream.

The PixArt OEM mice are known for disconnecting every minute in
runlevel 1 or 3 if they are not always polled. So add quirk
ALWAYS_POLL for two Primax mice as well.

0x4e22 is the Dell MS111-P and 0x4d0f is the unbranded HP Portia
mouse HP 697738-001. Both were built until approx. 2014.
Those were the standard mice from those vendors and are still
around - even as new old stock.

Reference: https://github.com/sriemer/fix-linux-mouse/issues/11Signed-off-by: Sebastian Parschauer <sparschauer@suse.de>
CC: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8c01db76 upstream.

When a UHID_CREATE command is written to the uhid char device, a
copy_from_user() is done from a user pointer embedded in the command.
When the address limit is KERNEL_DS, e.g. as is the case during
sys_sendfile(), this can read from kernel memory.  Alternatively,
information can be leaked from a setuid binary that is tricked to write
to the file descriptor.  Therefore, forbid UHID_CREATE in these cases.

No other commands in uhid_char_write() are affected by this bug and
UHID_CREATE is marked as "obsolete", so apply the restriction to
UHID_CREATE only rather than to uhid_char_write() entirely.

Thanks to Dmitry Vyukov for adding uhid definitions to syzkaller and to
Jann Horn for commit 9da3f2b7 ("x86/fault: BUG() when uaccess
helpers fault on kernel addresses"), allowing this bug to be found.

Reported-by: syzbot+72473edc9bf4eb1c6556@syzkaller.appspotmail.com
Fixes: d365c6cf ("HID: uhid: add UHID_CREATE and UHID_DESTROY events")
Cc: <stable@vger.kernel.org> # v3.6+
Cc: Jann Horn <jannh@google.com>
Cc: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Jann Horn <jannh@google.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 2bbb5fa3 upstream.

Many HP AMD based laptops contain an SMB0001 device like this:

Device (SMBD)
{
    Name (_HID, "SMB0001")  // _HID: Hardware ID
    Name (_CRS, ResourceTemplate ()  // _CRS: Current Resource Settings
    {
        IO (Decode16,
            0x0B20,             // Range Minimum
            0x0B20,             // Range Maximum
            0x20,               // Alignment
            0x20,               // Length
            )
        IRQ (Level, ActiveLow, Shared, )
            {7}
    })
}

The legacy style IRQ resource here causes acpi_dev_get_irqresource() to
be called with legacy=true and this message to show in dmesg:
ACPI: IRQ 7 override to edge, high

This causes issues when later on the AMD0030 GPIO device gets enumerated:

Device (GPIO)
{
    Name (_HID, "AMDI0030")  // _HID: Hardware ID
    Name (_CID, "AMDI0030")  // _CID: Compatible ID
    Name (_UID, Zero)  // _UID: Unique ID
    Method (_CRS, 0, NotSerialized)  // _CRS: Current Resource Settings
    {
	Name (RBUF, ResourceTemplate ()
	{
	    Interrupt (ResourceConsumer, Level, ActiveLow, Shared, ,, )
	    {
		0x00000007,
	    }
	    Memory32Fixed (ReadWrite,
		0xFED81500,         // Address Base
		0x00000400,         // Address Length
		)
	})
	Return (RBUF) /* \_SB_.GPIO._CRS.RBUF */
    }
}

Now acpi_dev_get_irqresource() gets called with legacy=false, but because
of the earlier override of the trigger-type acpi_register_gsi() returns
-EBUSY (because we try to register the same interrupt with a different
trigger-type) and we end up setting IORESOURCE_DISABLED in the flags.

The setting of IORESOURCE_DISABLED causes platform_get_irq() to call
acpi_irq_get() which is not implemented on x86 and returns -EINVAL.
resulting in the following in dmesg:

amd_gpio AMDI0030:00: Failed to get gpio IRQ: -22
amd_gpio: probe of AMDI0030:00 failed with error -22

The SMB0001 is a "virtual" device in the sense that the only way the OS
interacts with it is through calling a couple of methods to do SMBus
transfers. As such it is weird that it has IO and IRQ resources at all,
because the driver for it is not expected to ever access the hardware
directly.

The Linux driver for the SMB0001 device directly binds to the acpi_device
through the acpi_bus, so we do not need to instantiate a platform_device
for this ACPI device. This commit adds the SMB0001 HID to the
forbidden_id_list, avoiding the instantiating of a platform_device for it.
Not instantiating a platform_device means we will no longer call
acpi_dev_get_irqresource() for the legacy IRQ resource fixing the probe of
the AMDI0030 device failing.

BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1644013
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=198715
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199523Reported-by: Lukas Kahnert <openproggerfreak@gmail.com>
Tested-by: Marc <suaefar@googlemail.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit fee05f45 upstream.

req.gid can be indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.

This issue was detected with the help of Smatch:

vers/misc/sgi-gru/grukdump.c:200 gru_dump_chiplet_request() warn:
potential spectre issue 'gru_base' [w]

Fix this by sanitizing req.gid before calling macro GID_TO_GRU, which
uses it to index gru_base.

Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].

[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2

Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 5d1e9c22 upstream.

Use the new of_get_compatible_child() helper to lookup the nfc child
node instead of using of_find_compatible_node(), which searches the
entire tree from a given start node and thus can return an unrelated
(i.e. non-child) node.

This also addresses a potential use-after-free (e.g. after probe
deferral) as the tree-wide helper drops a reference to its first
argument (i.e. the node of the device being probed).

While at it, also fix a related nfc-node reference leak.

Fixes: f88fc122 ("mtd: nand: Cleanup/rework the atmel_nand driver")
Cc: stable <stable@vger.kernel.org>     # 4.11
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Josh Wu <rainyfeeling@outlook.com>
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 1decef37 upstream.

Passing a timeout of zero to the synchronous serdev_device_write()
helper does currently not imply to wait forever (unlike passing zero to
serdev_device_wait_until_sent()). Instead, if there's insufficient
room in the write buffer, we'd end up with an incomplete write.

Fixes: d2efbbd1 ("gnss: add driver for sirfstar-based receivers")
Cc: stable <stable@vger.kernel.org>     # 4.19
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 56a6c726 upstream.

Passing a timeout of zero to the synchronous serdev_device_write()
helper does currently not imply to wait forever (unlike passing zero to
serdev_device_wait_until_sent()). Instead, if there's insufficient
room in the write buffer, we'd end up with an incomplete write.

Fixes: 37768b05 ("gnss: add generic serial driver")
Cc: stable <stable@vger.kernel.org>     # 4.19
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f6501f49 upstream.

Add another Apple Cinema Display to the list of supported displays
Signed-off-by: Mattias Jacobsson <2pi@mok.nu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 7c973012 upstream.

After building the kernel with Clang, the following section mismatch
warning appears:

WARNING: vmlinux.o(.text+0x3bf19a6): Section mismatch in reference from
the function ssc_probe() to the function
.init.text:atmel_ssc_get_driver_data()
The function ssc_probe() references
the function __init atmel_ssc_get_driver_data().
This is often because ssc_probe lacks a __init
annotation or the annotation of atmel_ssc_get_driver_data is wrong.

Remove __init from atmel_ssc_get_driver_data to get rid of the mismatch.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit a7711257 upstream.

Following on from this patch: https://lkml.org/lkml/2017/11/3/516,
Corsair K70 LUX RGB keyboards also require the DELAY_INIT quirk to
start correctly at boot.

Dmesg output:
usb 1-6: string descriptor 0 read error: -110
usb 1-6: New USB device found, idVendor=1b1c, idProduct=1b33
usb 1-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-6: can't set config #1, error -110
Signed-off-by: Emmanuel Pescosta <emmanuelpescosta099@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 781f0766 upstream.

Devices connected under Terminus Technology Inc. Hub (1a40:0101) may
fail to work after the system resumes from suspend:
[  206.063325] usb 3-2.4: reset full-speed USB device number 4 using xhci_hcd
[  206.143691] usb 3-2.4: device descriptor read/64, error -32
[  206.351671] usb 3-2.4: device descriptor read/64, error -32

Info for this hub:
T:  Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  2 Spd=480 MxCh= 4
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1a40 ProdID=0101 Rev=01.11
S:  Product=USB 2.0 Hub
C:  #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub

Some expirements indicate that the USB devices connected to the hub are
innocent, it's the hub itself is to blame. The hub needs extra delay
time after it resets its port.

Hence wait for extra delay, if the device is connected to this quirky
hub.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit deefd242 upstream.

Raydium USB touchscreen fails to set config if LPM is enabled:
[    2.030658] usb 1-8: New USB device found, idVendor=2386, idProduct=3119
[    2.030659] usb 1-8: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.030660] usb 1-8: Product: Raydium Touch System
[    2.030661] usb 1-8: Manufacturer: Raydium Corporation
[    7.132209] usb 1-8: can't set config #1, error -110

Same behavior can be observed on 2386:3114.

Raydium claims the touchscreen supports LPM under Windows, so I used
Microsoft USB Test Tools (MUTT) [1] to check its LPM status. MUTT shows
that the LPM doesn't work under Windows, either. So let's just disable LPM
for Raydium touchscreens.

[1] https://docs.microsoft.com/en-us/windows-hardware/drivers/usbcon/usb-test-toolsSigned-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 63529eaa upstream.

The cdc-acm kernel module currently does not support the Hiro (Conexant)
H05228 USB modem. The patch below adds the device specific information:
	idVendor	0x0572
	idProduct	0x1349
Signed-off-by: Maarten Jacobs <maarten256@outlook.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 95217260 upstream.

If alloc_can_err_skb() fails, cf is never initialized.
Move assignment of cf inside check.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e13fb9b3 upstream.

The call to can_put_echo_skb() may result in the skb being freed. The skb
is later used in the call to dev->ops->dev_frame_to_cmd().

This is avoided by moving the call to can_put_echo_skb() after
dev->ops->dev_frame_to_cmd().
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d99501b8 upstream.

We need to call pci_iounmap() instead of iounmap() for the regions
obtained via pci_iomap() call for some archs that need special
treatment.

Fixes: aa31704f ("ALSA: hda/ca0132: Add PCI region2 iomap for SBZ")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 563785ed upstream.

HP Pavilion 15 (103c:820d) with ALC295 codec requires the quirk for
the mute LED control over mic3 pin.  Added the corresponding quirk
entry.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=201653
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 43279819 upstream.

I was trying to solve a double free but I introduced a more serious
NULL dereference bug.  The problem is that if there is an IRQ which
triggers immediately, then we need "info->uio_dev" but it's not set yet.

This patch puts the original initialization back to how it was and just
sets info->uio_dev to NULL on the error path so it should solve both
the Oops and the double free.

Fixes: f019f07e ("uio: potential double frees if __uio_register_device() fails")
Reported-by: Mathias Thore <Mathias.Thore@infinera.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Tested-by: Mathias Thore <Mathias.Thore@infinera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 21f70d4a upstream.

Sparse highlighted it, and appears to be a pure bug (from vs to).

./arch/riscv/include/asm/uaccess.h:403:35: warning: incorrect type in argument 1 (different address spaces)
./arch/riscv/include/asm/uaccess.h:403:39: warning: incorrect type in argument 2 (different address spaces)
./arch/riscv/include/asm/uaccess.h:409:37: warning: incorrect type in argument 1 (different address spaces)
./arch/riscv/include/asm/uaccess.h:409:41: warning: incorrect type in argument 2 (different address spaces)
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 82fba2df upstream.

Re-enable OCTEON USB driver which is needed on older hardware
(e.g. EdgeRouter Lite) for mass storage etc. This got accidentally
deleted when config options were changed for OCTEON2/3 USB.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: f922bc0a ("MIPS: Octeon: cavium_octeon_defconfig: Enable more drivers")
Patchwork: https://patchwork.linux-mips.org/patch/21077/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org # 4.14+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 92539d3e upstream.

Patch ad608fbc changed how events were subscribed to address an issue
elsewhere. As a side effect of that change, the "add" callback was called
before the event subscription was added to the list of subscribed events,
causing the first event queued by the add callback (and possibly other
events arriving soon afterwards) to be lost.

Fix this by adding the subscription to the list before calling the "add"
callback, and clean up afterwards if that fails.

Fixes: ad608fbc ("media: v4l: event: Prevent freeing event subscriptions while accessed")
Reported-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org (for 4.14 and up)
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b082f2dd upstream

Splitting out the sanity check in map_ldt_struct() moved page table syncing
into a separate function, which made the pgd variable unused. Remove it.

[ tglx: Massaged changelog ]

Fixes: 9bae3197 ("x86/ldt: Split out sanity check in map_ldt_struct()")
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Andy Lutomirski <luto@kernel.org>
Cc: bp@alien8.de
Cc: hpa@zytor.com
Cc: dave.hansen@linux.intel.com
Cc: peterz@infradead.org
Cc: boris.ostrovsky@oracle.com
Cc: jgross@suse.com
Cc: bhe@redhat.com
Cc: willy@infradead.org
Cc: linux-mm@kvack.org
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181026122856.66224-4-kirill.shutemov@linux.intel.comSigned-off-by: Sasha Levin <sashal@kernel.org>

commit a0e6e083 upstream

modify_ldt(2) leaves the old LDT mapped after switching over to the new
one. The old LDT gets freed and the pages can be re-used.

Leaving the mapping in place can have security implications. The mapping is
present in the userspace page tables and Meltdown-like attacks can read
these freed and possibly reused pages.

It's relatively simple to fix: unmap the old LDT and flush TLB before
freeing the old LDT memory.

This further allows to avoid flushing the TLB in map_ldt_struct() as the
slot is unmapped and flushed by unmap_ldt_struct() or has never been mapped
at all.

[ tglx: Massaged changelog and removed the needless line breaks ]

Fixes: f55f0501 ("x86/pti: Put the LDT in its own PGD if PTI is on")
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: bp@alien8.de
Cc: hpa@zytor.com
Cc: dave.hansen@linux.intel.com
Cc: luto@kernel.org
Cc: peterz@infradead.org
Cc: boris.ostrovsky@oracle.com
Cc: jgross@suse.com
Cc: bhe@redhat.com
Cc: willy@infradead.org
Cc: linux-mm@kvack.org
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181026122856.66224-3-kirill.shutemov@linux.intel.comSigned-off-by: Sasha Levin <sashal@kernel.org>

commit d52888aa upstream

On 5-level paging the LDT remap area is placed in the middle of the KASLR
randomization region and it can overlap with the direct mapping, the
vmalloc or the vmap area.

The LDT mapping is per mm, so it cannot be moved into the P4D page table
next to the CPU_ENTRY_AREA without complicating PGD table allocation for
5-level paging.

The 4 PGD slot gap just before the direct mapping is reserved for
hypervisors, so it cannot be used.

Move the direct mapping one slot deeper and use the resulting gap for the
LDT remap area. The resulting layout is the same for 4 and 5 level paging.

[ tglx: Massaged changelog ]

Fixes: f55f0501 ("x86/pti: Put the LDT in its own PGD if PTI is on")
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Andy Lutomirski <luto@kernel.org>
Cc: bp@alien8.de
Cc: hpa@zytor.com
Cc: dave.hansen@linux.intel.com
Cc: peterz@infradead.org
Cc: boris.ostrovsky@oracle.com
Cc: jgross@suse.com
Cc: bhe@redhat.com
Cc: willy@infradead.org
Cc: linux-mm@kvack.org
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181026122856.66224-2-kirill.shutemov@linux.intel.comSigned-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 025911a5 ]

There is no need to have the '__be32 *p' variable static since new value
always be assigned before use it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 8ef14c2c ]

This reverts commit 6147b1cf.

The reverted patch results in attempted write access to the source
repository, even if that repository is mounted read-only.

Output from "strace git status -uno --porcelain":

getcwd("/tmp/linux-test", 129)          = 16
open("/tmp/linux-test/.git/index.lock", O_RDWR|O_CREAT|O_EXCL|O_CLOEXEC, 0666) =
	-1 EROFS (Read-only file system)

While git appears to be able to handle this situation, a monitored
build environment (such as the one used for Chrome OS kernel builds)
may detect it and bail out with an access violation error. On top of
that, the attempted write access suggests that git _will_ write to the
file even if a build output directory is specified. Users may have the
reasonable expectation that the source repository remains untouched in
that situation.

Fixes: 6147b1cf ("scripts/setlocalversion: git: Make -dirty check more robust"
Cc: Genki Sky <sky@genki.is>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit bbcde0a7 ]

Since commit b41d920a ("kbuild: deb-pkg: split generating packaging
and build"), the build version of the kernel contained in a deb package
is too low by 1.

Prior to the bad commit, the kernel was built first, then the number
in .version file was read out, and written into the debian control file.

Now, the debian control file is created before the kernel is actually
compiled, which is causing the version number mismatch.

Let the mkdebian script pass KBUILD_BUILD_VERSION=${revision} to require
the build system to use the specified version number.

Fixes: b41d920a ("kbuild: deb-pkg: split generating packaging and build")
Reported-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>