In some response messages, there may be some extended info after the
message.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The existing code always reports NVSP_STAT_SUCCESS. This patch adds the
mechanism to report failure when it happens.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The receive code path doesn't use the page buffer, so remove the
extra allocated space here.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To prevent possible data corruption in RNDIS requests, add another
page buffer if the request message crossed page boundary.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Return ETIMEDOUT when the reply message is not received in time.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

According to RNDIS specs, Windows sets this size to
0x4000. I use the same value here.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move vxlan UDP socket to correct network namespace
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ben Hutchings says:

====================
Some bug fixes that should go into 3.7:

1. Fix oops when removing device with SR-IOV enabled.  (This regression
was introduced by the last set of changes, so the fix does not need to
be applied to any earlier kernel versions.)
2. Fix firmware structure field lookup bug that resulted in missing
sensor information.
3. Fix bug that makes self-test do very little in some configurations.
4. Fix the numbering of ethtool RX flow steering filters to reflect the
real hardware priorities.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Each RX filter table contains filters with two different levels of
specificity: TCP/IPv4 and UDP/IPv4 filters match the local address and
port and optionally the remote address and port; Ethernet filters
match the local address and optionally the VID.  The more specific
filters always override less specific filters within the same table,
and should be numbered accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

This filter flag cannot yet be set through the ethtool command and
will not be supported on future hardware.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

The loopback self-test iterates over all the TX queues of channel 0,
which is not very interesting when that's an RX-only channel.
Signed-off-by: Ben Hutchings <bhutchings@solarflre.com>

The least significant bit number (LBN) of a field within an MCDI
structure is counted from the start of the structure, not the
containing dword.  In MCDI_ARRAY_FIELD() we need to mask it rather
than using the usual EFX_DWORD_FIELD() macro.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

Commit c31e5f9f ('sfc: Add channel specific receive_skb handler and
post_remove callback') added the function pointer field
efx_channel_type::post_remove and an unconditional call through it.

This field should have been initialised to efx_channel_dummy_op_void
in the existing instances of efx_channel_type, but this was only done
in efx_default_channel_type.  Consequently, if a device has SR-IOV
enabled then removing the driver or device will result in an oops.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

This is an implementation of Virtual eXtensible Local Area Network
as described in draft RFC:
  http://tools.ietf.org/html/draft-mahalingam-dutt-dcops-vxlan-02

The driver integrates a Virtual Tunnel Endpoint (VTEP) functionality
that learns MAC to IP address mapping.

This implementation has not been tested only against the Linux
userspace implementation using TAP, not against other vendor's
equipment.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Needed for VXLAN.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Later changes need to be able to refer to neighbour attributes
when doing fdb_add.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is the seldom used corner case where HWMON=m at the same
time as TIGON3=y (typically randconfigs) which will cause a link
fail like:

drivers/built-in.o: In function `tg3_close':
tg3.c:(.text+0x16bd86): undefined reference to `hwmon_device_unregister'
drivers/built-in.o: In function `tg3_hwmon_open':
tg3.c:(.text+0x16fc4b): undefined reference to `hwmon_device_register'
make[1]: *** [vmlinux] Error 1

Fix it as suggested by DaveM[1] by having the Kconfig logic simply
select HWMON when TIGON3 is selected.  This gets rid of all the
extra IS_ENABLED ifdeffery in tg3.c as a side benefit.

[1] http://marc.info/?l=linux-netdev&m=134250573718151&w=2

Cc: Michael Chan <mchan@broadcom.com>
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reported-by: Anisse Astier <anisse@astier.eu>
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit d7559982.

It wasn't meant to be applied, commit
342b7b74 ("net: ti cpsw ethernet: set
IFCTL_A bit in MACCONTROL") was redone in such a way to make this
commit unnecessary.
Signed-off-by: David S. Miller <davem@davemloft.net>

Use be16 consistently when looking at flags.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This dongle ships with the X1 Carbon, and has an AX88772B
usb to ethernet chip in it.
Signed-off-by: Quinlan Pfiffer <qpfiffer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Due to a bug in most Flexcan cores, the bus error interrupt needs
to be enabled. Otherwise we don't get any error warning or passive
interrupts. This is _not_ necessary for the i.MX28 and this patch
disables bus error interrupts if "berr-reporting" is not requested.
This avoids bus error flooding, which might harm, especially on
low-end systems.

To handle such quirks of the Flexcan cores, a hardware feature flag
has been introduced, also replacing the "hw_ver" variable. So far
nobody could tell what Flexcan core version is available on what
Freescale SOC, apart from the i.MX6Q and P1010, and which bugs or
features are present on the various "hw_rev".

CC: Hui Wang <jason77.wang@gmail.com>
CC: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Because sizeof() is size_t then if "len" is negative, it counts as a
large positive value.

The call tree looks like:
pfkey_sendmsg()
-> pfkey_process()
   -> pfkey_spdadd()
      -> parse_ipsecrequests()
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the rtnl_link_ops changelink and fill_info callbacks, through
which the admin can now set/get the driver mode, etc policies.
Maintain the proprietary sysfs entries only for legacy childs.

For child devices, set dev->iflink to point to the parent
device ifindex, such that user space tools can now correctly
show the uplink relation as done for vlan, macvlan, etc
devices. Pointed out by Patrick McHardy <kaber@trash.net>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow users to specify the phy interface of the CPSW slaves. The new
node parameter is called "phy_if_mode" and is optional. The original
behaviour of the driver is preserved when not given.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

For RMII/RGMII mode operation in 100Mbps, the CPSW needs to set the
IFCTL_A bits in the MACCONTROL register. For all other PHY modes, this
bit is unused, so setting it unconditionally shouldn't cause any
trouble.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

After commit e22979d9 (mlx4_en: Moving to Interrupts for TX
completions) we no longer need to orphan skbs in mlx4_en_xmit()
since skb wont stay a long time in TX ring before their release.

Orphaning skbs in ndo_start_xmit() should be avoided as much as
possible, since it breaks TCP Small Queue or other flow control
mechanisms (per socket limits)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add GRO capability to IPv4 GRE tunnels, using the gro_cells
infrastructure.

Tested using IPv4 and IPv6 TCP traffic inside this tunnel, and
checking GRO is building large packets.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds a new include file (include/net/gro_cells.h), to bring GRO
(Generic Receive Offload) capability to tunnels, in a modular way.

Because tunnels receive path is lockless, and GRO adds a serialization
using a napi_struct, I chose to add an array of up to
DEFAULT_MAX_NUM_RSS_QUEUES cells, so that multi queue devices wont be
slowed down because of GRO layer.

skb_get_rx_queue() is used as selector.

In the future, we might add optional fanout capabilities, using rxhash
for example.

With help from Ben Hutchings who reminded me
netif_get_num_default_rss_queues() function.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

skb with CHECKSUM_NONE cant currently be handled by GRO, and
we notice this deep in GRO stack in tcp[46]_gro_receive()

But there are cases where GRO can be a benefit, even with a lack
of checksums.

This preliminary work is needed to add GRO support
to tunnels.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When an address is added on loopback (ip -6 a a 2002::1/128 dev lo), two routes
are added:
 - one in the local table:
    local 2002::1 via :: dev lo  proto none  metric 0
 - one the in main table (for the prefix):
    unreachable 2002::1 dev lo  proto kernel  metric 256  error -101

When the address is deleted, the route inserted in the main table remains
because we use rt6_lookup(), which returns NULL when dst->error is set, which
is the case here! Thus, it is better to use ip6_route_lookup() to avoid this
kind of filter.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch moves the bnx2x and cnic drivers into using FW 7.8.2
which was recently submitted into the linux-firmware tree.

A short summary of minor bugs fixed by this FW:
 1. In switch dependent mode, fix several issues regarding inner vlan
    vs. DCB priorities.
 2. iSCSI - not all packets were completed on a forward channel.
 3. DCB - fixed for 4-port devices.
 4. Fixed false parity reported in CAM memories when operating near -5%
    on the 1.0V core supply.
 5. ETS default settings are set to fairness between traffic classes
    (rather than strict priority), and uses the same chip receive buffer
    configuration for both PFC and pause.

For a complete list of fixes made by this FW, see commit 236367db
in the linux-firmware git repository.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Current VFs enumeration algorithm used in be_find_vfs does not take domain
number into the match. The match found in igb/ixgbe is more elegant and
safe.

This 2nd version uses pci_physfn instead of checking dev->physfn directly.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit ec47ea82(skb: Add inline helper for getting the skb end offset from
head) introduces this helper function, skb_end_offset(),
we should make use of it.
Signed-off-by: Weiping Pan <wpan@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem

John W. Linville says:

====================
Here is another batch of updates intended for 3.7...

Highlights include an hci_connect re-write in Bluetooth, HCI/LLC
layer separation in NFC, removal of the raw pn544 NFC driver, NFC LLCP
raw sockets support, improved IBSS auth frame handling in mac80211,
full-MAC AP mode notification support in mac80211, a lot of attention
paid to brcmfmac, and the usual level of updates to iwlwifi, ath9k,
mwifiex, and rt2x00, and various other updates.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Added and modified a few log messages mostly in probe path.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1) link_status_query() is always called to query the link-speed (speed
after applying qos). When there is no qos setting, link-speed is derived from
port-speed. Do all this inside this routine and hide this from the callers.

2) adpater->phy.forced_port_speed is not being set anywhere after being
initialized. Get rid of this variable.

3) Ignore async link_speed notifications till the initial value has been
fetched from FW.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>