Currently the ethtool_regs version is set to 0 for all DSA drivers.

Use this field to store the chip ID to simplify the pretty dump of
any interfaces registered by the "dsa" driver.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Willem de Bruijn says:

====================
net: SO_TIMESTAMPING fixes

Fix two omissions:

- tx timestamping is missing for AF_INET6/SOCK_RAW/IPPROTO_RAW
- SOF_TIMESTAMPING_OPT_ID is missing for IPPROTO_RAW, PF_PACKET, CAN

Discovered while expanding the selftest in

  tools/testing/selftests/networking/timestamping/txtimestamp.c

Will send the test patchset to net-next once the fixes make it to that
branch. For now, it is available at

  https://github.com/wdebruij/linux/commits/txtimestamp-test-1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

SOF_TIMESTAMPING_OPT_ID is supported on TCP, UDP and RAW sockets.
But it was missing on RAW with IPPROTO_IP, PF_PACKET and CAN.

Add skb_setup_tx_timestamp that configures both tx_flags and tskey
for these paths that do not need corking or use bytestream keys.

Fixes: 09c2d251 ("net-timestamp: add key to disambiguate concurrent datagrams")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Raw sockets support tx timestamping, but one case is missing.

IPPROTO_RAW takes a separate packet construction path. raw_send_hdrinc
has an explicit call to sock_tx_timestamp, but rawv6_send_hdrinc does
not. Add it.

Fixes: 11878b40 ("net-timestamp: SOCK_RAW and PING timestamping")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make my Gmail address the primary one from now on.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Recent changes in the mvneta driver reworked allocation
and handling of the ingress buffers to use entire pages.
Apart from that in SW BM scenario the HW must be informed
via PRXDQS about the biggest possible incoming buffer
that can be propagated by RX descriptors.

The BufferSize field was filled according to the MTU-dependent
pkt_size value. Later change to PAGE_SIZE broke RX operation
when usin 64K pages, as the field is simply too small.

This patch conditionally limits the value passed to the BufferSize
of the PRXDQS register, depending on the PAGE_SIZE used.
On the occasion remove now unused frag_size field of the mvneta_port
structure.

Fixes: 562e2f46 ("net: mvneta: Improve the buffer allocation method for SWBM")
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Peng Li says:

====================
net: hns: Code improvements & fixes for HNS driver

This patchset introduces some code improvements and fixes
for the identified problems in the HNS driver.

Every patch is independent.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Create a net bridge, add eth and vnet to the bridge. The vnet is used
by a virtual machine. When ping the virtual machine from the outside
host and the virtual machine send multicast at the same time, the ping
package will lost.

The multicast package send to the eth, eth will send it to the bridge too,
and the bridge learn the mac of eth. When outside host ping the virtual
mechine, it will match the promisc entry of the eth which is not expected,
and the bridge send it to eth not to vnet, cause ping lost.

So this patch change promisc tcam entry position to the END of 512 tcam
entries, which indicate lower priority. And separate one promisc entry to
two: mc & uc, to avoid package match the wrong tcam entry.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In some case, when mac enable|disable and adjust link, may cause hard to
link(or abnormal) between mac and phy. This patch adds the code for rx PCS
to avoid this bug.

Disable the rx PCS when driver disable the gmac, and enable the rx PCS
when driver enable the mac.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ntuple-filters features is forced on by chip.
But it shows "ntuple-filters: off [fixed]" when use ethtool.
This patch make it correct with "ntuple-filters: on [fixed]".
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There will be a large number of MAC pause frames on the net,
which caused tx timeout of net device. And then the net device
was reset to try to recover it. So that is not useful, and will
cause some other problems.

So need doubled ndev->watchdog_timeo if device watchdog occurred
until watchdog_timeo up to 40s and then try resetting to recover
it.

When collecting dfx information such as hardware registers when tx timeout.
Some registers for count were cleared when read. So need move this task
before update net state which also read the count registers.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1.In "hns_nic_init_irq", if request irq fail at index i,
  the function return directly without releasing irq resources
  that already requested.

2.In "hns_nic_net_up" after "hns_nic_init_irq",
  if exceptional branch occurs, irqs that already requested
  are not release.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If there are packets in hardware when changing the speed or duplex,
it may cause hardware hang up.

This patch adds the code to wait rx fbd clean up when ae stopped.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After resetting dsaf to try to repair chip error such as ecc error,
the net device will be open if net interface is up. But at this time
if there is the users set the net device up with the command ifconfig,
the net device will be opened twice consecutively.

Function napi_enable was called when open device. And Kernel panic will
be occurred if it was called twice consecutively. Such as follow:
static inline void napi_enable(struct napi_struct *n)
{
         BUG_ON(!test_bit(NAPI_STATE_SCHED, &n->state));
         smp_mb__before_clear_bit();
         clear_bit(NAPI_STATE_SCHED, &n->state);
}

[37255.571996] Kernel panic - not syncing: BUG!
[37255.595234] Call trace:
[37255.597694] [<ffff80000008ab48>] dump_backtrace+0x0/0x1a0
[37255.603114] [<ffff80000008ad08>] show_stack+0x20/0x28
[37255.608187] [<ffff8000009c4944>] dump_stack+0x98/0xb8
[37255.613258] [<ffff8000009c149c>] panic+0x10c/0x26c
[37255.618070] [<ffff80000070f134>] hns_nic_net_up+0x30c/0x4e0
[37255.623664] [<ffff80000070f39c>] hns_nic_net_open+0x94/0x12c
[37255.629346] [<ffff80000084be78>] __dev_open+0xf4/0x168
[37255.634504] [<ffff80000084c1ac>] __dev_change_flags+0x98/0x15c
[37255.640359] [<ffff80000084c29c>] dev_change_flags+0x2c/0x68
[37255.769580] [<ffff8000008dc400>] devinet_ioctl+0x650/0x704
[37255.775086] [<ffff8000008ddc38>] inet_ioctl+0x98/0xb4
[37255.780159] [<ffff800000827b7c>] sock_do_ioctl+0x44/0x84
[37255.785490] [<ffff800000828e04>] sock_ioctl+0x248/0x30c
[37255.790737] [<ffff80000026dc6c>] do_vfs_ioctl+0x480/0x618
[37255.796156] [<ffff80000026de94>] SyS_ioctl+0x90/0xa4
[37255.801139] SMP: stopping secondary CPUs
[37255.805079] kbox: catch panic event.
[37255.809586] collected_len = 128928, LOG_BUF_LEN_LOCAL = 131072
[37255.816103] flush cache 0xffff80003f000000  size 0x800000
[37255.822192] flush cache 0xffff80003f000000  size 0x800000
[37255.828289] flush cache 0xffff80003f000000  size 0x800000
[37255.834378] kbox: no notify die func register. no need to notify
[37255.840413] ---[ end Kernel panic - not syncing: BUG!

This patchset fix this bug according to the flag NIC_STATE_DOWN.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

According to the hip06 datasheet:
1.Six registers use wrong address:
  RCB_COM_SF_CFG_INTMASK_RING
  RCB_COM_SF_CFG_RING_STS
  RCB_COM_SF_CFG_RING
  RCB_COM_SF_CFG_INTMASK_BD
  RCB_COM_SF_CFG_BD_RINT_STS
  DSAF_INODE_VC1_IN_PKT_NUM_0_REG
2.The offset of DSAF_INODE_VC1_IN_PKT_NUM_0_REG should be
  0x103C + 0x80 * all_chn_num
3.The offset to show the value of DSAF_INODE_IN_DATA_STP_DISC_0_REG
  is wrong, so the value of DSAF_INODE_SW_VLAN_TAG_DISC_0_REG will be
  overwrite

These registers are only used in "ethtool -d", so that did not cause ndev
to misfunction.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are two test cases:
1. Remove the 4 modules:hns_enet_drv/hns_dsaf/hnae/hns_mdio,
   and install them again, must use "ifconfig down/ifconfig up"
   command pair to bring port to work.

   This patch calls phy_stop function when init phy to fix this bug.

2. Remove the 2 modules:hns_enet_drv/hns_dsaf, and install them again,
   all ports can not use anymore, because of the phy devices register
   failed(phy devices already exists).

   Phy devices are registered when hns_dsaf installed, this patch
   removes them when hns_dsaf removed.

The two cases are sometimes related, fixing the second case also requires
fixing the first case, so fix them together.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

According to the hip06 Datasheet:
1. The offset of INGRESS_SW_VLAN_TAG_DISC should be 0x1A00+4*all_chn_num
2. The offset of INGRESS_IN_DATA_STP_DISC should be 0x1A50+4*all_chn_num
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sergey reported that forwarding was no longer working
if fq packet scheduler was used.

This is caused by the recent switch to EDT model, since incoming
packets might have been timestamped by __net_timestamp()

__net_timestamp() uses ktime_get_real(), while fq expects packets
using CLOCK_MONOTONIC base.

The fix is to clear skb->tstamp in forwarding paths.

Fixes: 80b14dee ("net: Add a new socket option for a future transmit time.")
Fixes: fb420d5d ("tcp/fq: move back to CLOCK_MONOTONIC")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Sergey Matyukevich <geomatsi@gmail.com>
Tested-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 7969e5c4 ("ip: discard IPv4 datagrams with overlapping
segments.") IPv4 reassembly code drops the whole queue whenever an
overlapping fragment is received. However, the test is written in a way
which detects duplicate fragments as overlapping so that in environments
with many duplicate packets, fragmented packets may be undeliverable.

Add an extra test and for (potentially) duplicate fragment, only drop the
new fragment rather than the whole queue. Only starting offset and length
are checked, not the contents of the fragments as that would be too
expensive. For similar reason, linear list ("run") of a rbtree node is not
iterated, we only check if the new fragment is a subset of the interval
covered by existing consecutive fragments.

v2: instead of an exact check iterating through linear list of an rbtree
node, only check if the new fragment is subset of the "run" (suggested
by Eric Dumazet)

Fixes: 7969e5c4 ("ip: discard IPv4 datagrams with overlapping segments.")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added support for the Telit LN940 series cellular modules QMI interface.
QMI_QUIRK_SET_DTR quirk requied for Qualcomm MDM9x40 chipset.
Signed-off-by: Jörgen Storvist <jorgen.storvist@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added support for Fibocom NL668 series QMI interface.
Using QMI_QUIRK_SET_DTR required for Qualcomm MDM9x07 chipsets.
Signed-off-by: Jörgen Storvist <jorgen.storvist@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexei Starovoitov says:

====================
pull-request: bpf 2018-12-15

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) fix liveness propagation of callee saved registers, from Jakub.

2) fix overflow in bpf_jit_limit knob, from Daniel.

3) bpf_flow_dissector api fix, from Stanislav.

4) bpf_perf_event api fix on powerpc, from Sandipan.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc_wait_for_cond() drops socket lock before going to sleep,
but tsk->group could be freed right after that release_sock().
So we have to re-check and reload tsk->group after it wakes up.

After this patch, tipc_wait_for_cond() returns -ERESTARTSYS when
tsk->group is NULL, instead of continuing with the assumption of
a non-NULL tsk->group.

(It looks like 'dsts' should be re-checked and reloaded too, but
it is a different bug.)

Similar for tipc_send_group_unicast() and tipc_send_group_anycast().

Reported-by: syzbot+10a9db47c3a0e13eb31c@syzkaller.appspotmail.com
Fixes: b7d42635 ("tipc: introduce flow control for group broadcast messages")
Fixes: ee106d7f ("tipc: introduce group anycast messaging")
Fixes: 27bd9ec0 ("tipc: introduce group unicast messaging")
Cc: Ying Xue <ying.xue@windriver.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While most distributions long ago switched to the iproute2 suite
of utilities, which allow class-e (240.0.0.0/4) address assignment,
distributions relying on busybox, toybox and other forms of
ifconfig cannot assign class-e addresses without this kernel patch.

While CIDR has been obsolete for 2 decades, and a survey of all the
open source code in the world shows the IN_whatever macros are also
obsolete... rather than obsolete CIDR from this ioctl entirely, this
patch merely enables class-e assignment, sanely.
Signed-off-by: Dave Taht <dave.taht@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vr.mifi is indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.

This issue was detected with the help of Smatch:

net/ipv6/ip6mr.c:1845 ip6mr_ioctl() warn: potential spectre issue 'mrt->vif_table' [r] (local cap)
net/ipv6/ip6mr.c:1919 ip6mr_compat_ioctl() warn: potential spectre issue 'mrt->vif_table' [r] (local cap)

Fix this by sanitizing vr.mifi before using it to index mrt->vif_table'

Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].

[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The get_mac_address() function is normally inline, but when it is
not, we get a warning that this configuration is broken:

WARNING: vmlinux.o(.text+0x4aff00): Section mismatch in reference from the function w90p910_ether_setup() to the function .init.text:get_mac_address()
The function w90p910_ether_setup() references
the function __init get_mac_address().
This is often because w90p910_ether_setup lacks a __init

Remove the __init to make it always do the right thing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The old code always starts from fixed port for VMADDR_PORT_ANY. Sometimes
when VMM crashed, there is still orphaned vsock which is waiting for
close timer, then it could cause connection time out for new started VM
if they are trying to connect to same port with same guest cid since the
new packets could hit that orphaned vsock. We could also fix this by doing
more in vhost_vsock_reset_orphans, but any way, it should be better to start
from a random local port instead of a fixed one.
Signed-off-by: Lepton Wu <ytht.net@gmail.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

All previous docks and dongles that have supported this feature use
the RTL8153-AD chip.

RTL8153-BND is a new chip that will be used in upcoming Dell type-C docks.
It should be added to the whitelist of devices to activate MAC address
pass through.

Per confirming with Realtek all devices containing RTL8153-BND should
activate MAC pass through and there won't use pass through bit on efuse
like in RTL8153-AD.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

recalculated send and receive window using linkspeed.
Determine correct value of eck_ok from SYN received and
option configured on local system.
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

corrected macro used in tx path. removed redundant hdrlen
and check for !page in chtls_sendmsg
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

listen fails when more than one tls capable device is
registered. tls_hw_hash is called for each dev which loops
again for each cdev_list causing listen failure. Hence
call chtls_listen_start/stop for specific device than loop over all
devices.
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

HW unhash within mutex for registered tls devices cause sleep
when called from tcp_set_state for TCP_CLOSE. Release lock and
re-acquire after function call with ref count incr/dec.
defined kref and fp release for tls_device to ensure device
is not released outside lock.

BUG: sleeping function called from invalid context at
kernel/locking/mutex.c:748
in_atomic(): 1, irqs_disabled(): 0, pid: 0, name: swapper/7
INFO: lockdep is turned off.
CPU: 7 PID: 0 Comm: swapper/7 Tainted: G        W  O
Call Trace:
 <IRQ>
 dump_stack+0x5e/0x8b
 ___might_sleep+0x222/0x260
 __mutex_lock+0x5c/0xa50
 ? vprintk_emit+0x1f3/0x440
 ? kmem_cache_free+0x22d/0x2a0
 ? tls_hw_unhash+0x2f/0x80
 ? printk+0x52/0x6e
 ? tls_hw_unhash+0x2f/0x80
 tls_hw_unhash+0x2f/0x80
 tcp_set_state+0x5f/0x180
 tcp_done+0x2e/0xe0
 tcp_rcv_state_process+0x92c/0xdd3
 ? lock_acquire+0xf5/0x1f0
 ? tcp_v4_rcv+0xa7c/0xbe0
 ? tcp_v4_do_rcv+0x70/0x1e0
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

create_ctx is called from tls_init and tls_hw_prot
hence initialize function pointers in common routine.
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Clang warns:

drivers/net/ethernet/apm/xgene/xgene_enet_main.c:33:36: warning:
tentative array definition assumed to have one element
static const struct acpi_device_id xgene_enet_acpi_match[];
                                   ^
1 warning generated.

Both xgene_enet_acpi_match and xgene_enet_of_match are defined before
their uses at the bottom of the file so this is unnecessary. When
CONFIG_ACPI is disabled, ACPI_PTR becomes NULL so xgene_enet_acpi_match
doesn't need to be defined.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When TIPC_NLA_UDP_REMOTE is an IPv6 mcast address but
TIPC_NLA_UDP_LOCAL is an IPv4 address, a NULL-ptr deref is triggered
as the UDP tunnel sock is initialized to IPv4 or IPv6 sock merely
based on the protocol in local address.

We should just error out when the remote address and local address
have different protocols.

Reported-by: syzbot+eb4da3a20fad2e52555d@syzkaller.appspotmail.com
Cc: Ying Xue <ying.xue@windriver.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc_udp_xmit() drops the packet on error, there is no
need to drop it again.

Fixes: ef20cd4d ("tipc: introduce UDP replicast")
Reported-and-tested-by: syzbot+eae585ba2cc2752d3704@syzkaller.appspotmail.com
Cc: Ying Xue <ying.xue@windriver.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

lock_sock() must be used in process context to be race-free with
other lock_sock() callers, for example, tipc_release(). Otherwise
using the spinlock directly can't serialize a parallel tipc_release().

As it is blocking, we have to hold the sock refcnt before
rhashtable_walk_stop() and release it after rhashtable_walk_start().

Fixes: 07f6c4bc ("tipc: convert tipc reference table to use generic rhashtable")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Ying Xue <ying.xue@windriver.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NETLINK_DUMP_STRICT_CHK can be used for all GET requests,
dumps as well as doit handlers.  Replace the DUMP in the
name with GET make that clearer.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The value for OEM_CFG_UPDATE command differs between driver and the
Management firmware (mfw). Fix this gap with adding a reserved field.

Fixes: cac6f691 ("qed: Add support for Unified Fabric Port.")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>