Below listed hal descriptor mask are incorrect, so modify it to correct one
 - CE destination status description meta info mask is increased from
   8 bits to 16 bits from the 0th bit position
 - Rx Reo queue duplicate count mask is decreased from 22 bits to 16 bits
 - Reo threshold status counter sum mask is increased from 24 bits to 26 bits

No functionality impact, these descriptors are currently not used in any
supported platform. But in future if someone referred these descriptor then
ended with wrong values.

Found this during code review.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604511921-24840-1-git-send-email-periyasa@codeaurora.org

driver not able to bootup in the single radio configured board.
single phy hw mode is converted to invalid hw mode and sent to FW
through wmi init cmd. In that case driver is not receiving wmi
ready event which leads to driver bootup fail. single phy hw mode
is a valid for single radio configured board. so removed the
conversion logic.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604511331-22477-1-git-send-email-periyasa@codeaurora.org

The ath11k code will try to insert wheather rader related limits when the
DFS region is set to ETSI. For this reason, it will add two more entries in
the array of reg_rules. But the 2.4.0.1 firmware is prefiltering the list
of reg rules it returns for 2.4GHz PHYs. They will then not contain the
list of 5GHz rules and thus no wheather radar band rules were inserted by
this code.

But the code didn't fix the n_reg_rules for this regulatory domain and PHY
when this happened. This resulted in a rejection by is_valid_rd because it
found rules which start and end at 0khz. This resulted in a splat like:

  Invalid regulatory domain detected
  ------------[ cut here ]------------
  WARNING: at backports-20200628-4.4.60-9a94b73e75/net/wireless/reg.c:3721
  [...]
  ath11k c000000.wifi1: failed to perform regd update : -22

The number of rules must therefore be saved after they were converted from
the ath11k format to the ieee80211_regdomain format and not before.

Tested with IPQ8074 WLAN.HK.2.4.0.1.r1-00019-QCAHKSWPL_SILICONZ-1

Fixes: d5c65159 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201030101940.2387952-1-sven@narfation.org

qdf_ctx is not used in wmi_mgmt_params, remove this
un-used variable.

Compile tested only.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1603339175-12706-1-git-send-email-govinds@codeaurora.org

The function ath11k_wmi_send_init_country_cmd is taking 3 byte from alpha2
of the structure wmi_init_country_params. But the function
ath11k_reg_notifier is only initializing 2 bytes. The third byte is
therefore always an uninitialized value.

The command can happen to look like

  0c 00 87 02 01 00 00 00 00 00 00 00 43 41 f8 00

instead of

  0c 00 87 02 01 00 00 00 00 00 00 00 43 41 00 00

Tested-on: IPQ8074 hw2.0 WLAN.HK.2.1.0.1-01161-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.4.0.1.r1-00019-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.4.0.1.r1-00026-QCAHKSWPL_SILICONZ-2

Fixes: d5c65159 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201021140555.4114715-1-sven@narfation.org

cold boot calibration is the process to calibrate all the channels
during the boot-up to avoid the calibration delay during the
channel change.
During the boot-up, firmware started in cold boot calibration mode
Firmware calibrate all channels and generate CalDb(DDR).
Subsequent wifi bringup will reuse the same CalDb.
Firmware is restarted in normal mode to continue the normal operation.

caldb memory address send to firmware through the QMI message.Firmware
use this address to store the caldb data and use it until next reboot.

This will give the improvement during the channel change. But it is
increasing the boot-up time(up to 15sec depend on number of radios).
So if the user want to reduce the boot-up time and accepting for channel
change delay, user can disable this feature using the module param
cold_boot_cal=0.

Tested-on: IPQ8074 WLAN.HK.2.4.0.1-01162-QCAHKSWPL_SILICONZ-1
Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Co-developed-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1602862111-14063-1-git-send-email-ssreeela@codeaurora.org

Board Data File (BDF) is loaded upon driver boot-up procedure. The right
board data file is identified on IPQ6018 using bus, qmi-chip-id and
qmi-board-id.

The problem, however, can occur when the (default) board data file cannot
fulfill with the vendor requirements and it is necessary to use a different
board data file.

This problem was already solved on ath10k by adding a ",variant=.*" at the
end of the board name. The same functionality must also be provided for
ath11k.

The device tree requires an additional string to define the variant name

    wifi@c000000 {
        status = "okay";
        qcom,ath11k-calibration-variant = "Cigtech-WF-188";
    };

This would create the boarddata identifier for the board-2.bin search

 *  bus=ahb,qmi-chip-id=0,qmi-board-id=18,variant=Cigtech-WF-188
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201015131501.1939685-2-sven@narfation.org

The bus + qmi-chip-id + qmi-board-id is not enough to identify the correct
board data file on IPQ6018 based devices. Multiple different boards share
the same values. Only the original reference designs can currently be
identified and loaded from the board-2.bin. But these will not result in
the correct calibration data when combined with the pre-calibration data
from the device.

An additional "variant" information has to be provided to select the
correct board data for a design which was modified by an ODM. This follows
the same approach as ath10k.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201015131501.1939685-1-sven@narfation.org

Monitor ring Rx buffer is not really modified between dma map
and unmap. So remove the unnecssary data sync before dma unmap.
This does not fix any visible issue, found in code review.

Compile tested only.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1602744454-22969-1-git-send-email-vthiagar@codeaurora.org

In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <apais@linux.microsoft.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201007103309.363737-4-allen.lkml@gmail.com

The rx worker of SDIO should be cancelled after disable interrupt, and
release rx sk_buff in queue, otherwise the rx worker maybe still run
after hif_stop. And it should be cancelled before napi_synchronize in
hif_stop, because the rx worker of SDIO will call napi_schedule, it
should have no napi_schedule before napi_synchronize, otherwise it
lead napi_synchronize wait untill napi_complete.

Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00049
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604558036-4056-1-git-send-email-wgong@codeaurora.org

This fixes possible crash scenario where interfaces that were not
set up in the driver yet might still be iterated over.  When originally
debugged on the ath10k-ct driver, the crash looked like this:

kernel BUG at /home/greearb/git/linux-4.7.dev.y/drivers/net/wireless/ath/ath10k/wmi.c:1781!
invalid opcode: 0000 [#1] PREEMPT SMP KASAN
Modules linked in: nf_conntrack_netlink nf_conntrack nfnetlink nf_defrag_ipv4 bridge carl9170 mac80211_hwsim ath10k_pci ath10k_core ath5k ath9k ath9k_common ath9k_hw ath mac80211 cfg80211 8021q garp mrp stp llc bnep bluetooth fuse macvlan pktgen rpcsec_gss_krb5 nfsv4 nfs fscache snd_hda_codec_hdmi coretemp hwmon intel_rapl x86_pkg_temp_thermal intel_powerclamp snd_hda_codec_realtek snd_hda_codec_generic kvm iTCO_wdt irqbypass iTCO_vendor_support joydev snd_hda_intel snd_hda_codec snd_hda_core snd_hwdep snd_seq snd_seq_device pcspkr snd_pcm snd_timer shpchp snd i2c_i801 lpc_ich soundcore tpm_tis tpm nfsd auth_rpcgss nfs_acl lockd grace sunrpc i915 serio_raw i2c_algo_bit drm_kms_helper ata_generic e1000e pata_acpi drm ptp pps_core i2c_core fjes video ipv6 [last unloaded: nf_conntrack]
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.7.10+ #15
Hardware name: To be filled by O.E.M. To be filled by O.E.M./ChiefRiver, BIOS 4.6.5 06/07/2013
task: ffff8801d4f20000 ti: ffff8801d4f28000 task.ti: ffff8801d4f28000
RIP: 0010:[<ffffffffa0efbcfb>]  [<ffffffffa0efbcfb>] ath10k_wmi_tx_beacons_iter+0x28b/0x290 [ath10k_core]
RSP: 0018:ffff8801d6447a98  EFLAGS: 00010293
RAX: 0000000000000018 RBX: ffff8801ce97e1d8 RCX: 0000000000000000
RDX: 0000000000000018 RSI: 0000000000000003 RDI: ffffed003ac88f49
RBP: ffff8801d6447af0 R08: 0000000000000003 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000001 R12: 0000000000000000
R13: ffff8801ce97e320 R14: ffff8801ce97e378 R15: ffff8801ce97ca40
FS:  0000000000000000(0000) GS:ffff8801d6440000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007eff191ef1ab CR3: 000000000260a000 CR4: 00000000001406e0
Stack:
 1ffff1003ac88f59 0000000041b58ab3 ffffffffa0f4d52a ffff8801d4f20000
 0000000000000246 0000000000000002 ffff8801ce97e1d8 ffff8801bd5d39b8
 0000000000000002 0000000000000001 ffff8801ce97ca40 ffff8801d6447b48
Call Trace:
 <IRQ>
 [<ffffffffa0d03e5c>] __iterate_interfaces+0xfc/0x1d0 [mac80211]
 [<ffffffffa0efba70>] ? ath10k_wmi_cmd_send_nowait+0x260/0x260 [ath10k_core]
 [<ffffffffa0efba70>] ? ath10k_wmi_cmd_send_nowait+0x260/0x260 [ath10k_core]
 [<ffffffffa0d04477>] ieee80211_iterate_active_interfaces_atomic+0x67/0x100 [mac80211]
 [<ffffffffa0d04410>] ? ieee80211_handle_reconfig_failure+0x140/0x140 [mac80211]
 [<ffffffffa0ef4060>] ? ath10k_tpc_config_disp_tables+0x620/0x620 [ath10k_core]
 [<ffffffffa0ef408b>] ath10k_wmi_op_ep_tx_credits+0x2b/0x50 [ath10k_core]
 [<ffffffffa0ee2fd2>] ath10k_htc_rx_completion_handler+0x422/0x5c0 [ath10k_core]
 [<ffffffffa0b4301e>] ath10k_pci_process_rx_cb+0x37e/0x430 [ath10k_pci]
 [<ffffffffa0ee2bb0>] ? ath10k_htc_build_tx_ctrl_skb+0xc0/0xc0 [ath10k_core]
 [<ffffffffa0b42ca0>] ? ath10k_pci_rx_post_pipe+0x550/0x550 [ath10k_pci]
 [<ffffffff8120cbe5>] ? debug_lockdep_rcu_enabled+0x35/0x40
 [<ffffffff811e1893>] ? mark_held_locks+0x23/0xc0
 [<ffffffff8116019a>] ? __local_bh_enable_ip+0x6a/0xd0
 [<ffffffff811e1abb>] ? trace_hardirqs_on_caller+0x18b/0x290
 [<ffffffff811e1bcd>] ? trace_hardirqs_on+0xd/0x10
 [<ffffffff8116019a>] ? __local_bh_enable_ip+0x6a/0xd0
 [<ffffffff81df11d0>] ? _raw_spin_unlock_bh+0x30/0x40
 [<ffffffffa0b4902e>] ? ath10k_ce_per_engine_service+0xee/0x100 [ath10k_pci]
 [<ffffffffa0b43139>] ath10k_pci_htt_htc_rx_cb+0x29/0x30 [ath10k_pci]
 [<ffffffffa0b48fe6>] ath10k_ce_per_engine_service+0xa6/0x100 [ath10k_pci]
 [<ffffffffa0b49116>] ath10k_ce_per_engine_service_any+0xd6/0xf0 [ath10k_pci]
 [<ffffffffa0b45800>] ? ath10k_pci_enable_legacy_irq+0xe0/0xe0 [ath10k_pci]
 [<ffffffffa0b4585f>] ath10k_pci_tasklet+0x5f/0xb0 [ath10k_pci]
 [<ffffffff81160445>] tasklet_action+0x245/0x2b0
 [<ffffffff81df4831>] __do_softirq+0x181/0x595
 [<ffffffff8116137c>] irq_exit+0xbc/0xc0
 [<ffffffff81df423c>] do_IRQ+0x7c/0x150
 [<ffffffff81df23cc>] common_interrupt+0x8c/0x8c
 <EOI>
 [<ffffffff811e1abb>] ? trace_hardirqs_on_caller+0x18b/0x290
 [<ffffffff81b722ae>] ? cpuidle_enter_state+0x1ae/0x4b0
 [<ffffffff81b722a7>] ? cpuidle_enter_state+0x1a7/0x4b0
 [<ffffffff81b72602>] cpuidle_enter+0x12/0x20
 [<ffffffff811d0b6e>] call_cpuidle+0x4e/0x90
 [<ffffffff811d10e7>] cpu_startup_entry+0x3f7/0x540
 [<ffffffff811d0cf0>] ? default_idle_call+0x50/0x50
 [<ffffffff81234bdf>] ? clockevents_config_and_register+0x5f/0x70
 [<ffffffff81085a9a>] ? setup_APIC_timer+0xfa/0x110
 [<ffffffff81083b63>] start_secondary+0x253/0x2b0
 [<ffffffff81083910>] ? set_cpu_sibling_map+0x920/0x920
Code: 4d 49 e0 8b b3 48 01 00 00 48 c7 c7 a0 ee f3 a0 e8 d9 c2 3f e0 49 81 fd 3f 1f 00 00 76 0f 49 81 fc 3f 1f 00 00 0f 87 c0 fd ff ff <0f> 0b 0f 0b 90 55 48 89 e5 41 57 41 56 48 8d 85 58 ff ff ff 41
RIP  [<ffffffffa0efbcfb>] ath10k_wmi_tx_beacons_iter+0x28b/0x290 [ath10k_core]
 RSP <ffff8801d6447a98>
---[ end trace 6588464714e5163a ]---

Similar logic was tested for years in ath10k-ct driver and various firmware.

Also tested with stock kernel plus this patch, with firmware
10.2.4-1.0-00037

This test case was to bring up 5 vap on a radio and fake a firmware
crash.  Make sure ap interfaces continue to function properly.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200922191957.25257-2-greearb@candelatech.com

This change fixes below compilation warning.

smatch warnings:
 drivers/net/wireless/ath/ath10k/mac.c:9125 ath10k_mac_op_set_tid_config() error: uninitialized symbol 'ret'.

No functional changes. Compile tested only.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604507837-29361-1-git-send-email-tamizhr@codeaurora.org

This patch adds driver support for FILS discovery and unsolicited
broadcast probe response transmission features which are used for
in-band discovery in 6GHz band.
Currently this support is enabled only in 6GHz by setting hardware flags.

Changes include WMI commands to enable transmission, set packet
interval, set template, and handle events.
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201007204036.19780-1-alokad@codeaurora.org

The for loop checks whether cur_section is NULL on every iteration, but
we know it can never be NULL as there is another check towards the
bottom of the loop body. Refactor to avoid this unnecessary check.

Also, increment the variable i inline for clarity

Addresses-Coverity: 1496984 ("Null pointer dereferences)
Suggested-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200916165748.20927-1-alex.dewar90@gmail.com

Found by latest checkpatch.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1603803705-22447-1-git-send-email-kvalo@codeaurora.org

Latest checkpatch complains about use of fall-through comment. But as this is a
switch statement just reword the comment to workaround the problem.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1603802288-21158-2-git-send-email-kvalo@codeaurora.org

Found by latest checkpatch.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1603802288-21158-1-git-send-email-kvalo@codeaurora.org

Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.

Remove the quote operator # from compiler_attributes.h __section macro.

Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.

Conversion done using the script at:

    https://lore.kernel.org/lkml/75393e5ddc272dc7403de74d645e6c6e0f4e70eb.camel@perches.com/2-convert_section.plSigned-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@gooogle.com>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

tid_addr is not a "pointer to (pointer to int in userspace)"; it is in
fact a "pointer to (pointer to int in userspace) in userspace".  So
sparse rightfully complains about passing a kernel pointer to
put_user().
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 453431a5 ("mm, treewide: rename kzfree() to
kfree_sensitive()") renamed kzfree() to kfree_sensitive(),
but it left a compatibility definition of kzfree() to avoid
being too disruptive.

Since then a few more instances of kzfree() have slipped in.

Just get rid of them and remove the compatibility definition
once and for all.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If set, use the environment variable GIT_DIR to change the default .git
location of the kernel git tree.

If GIT_DIR is unset, keep using the current ".git" default.

Link: https://lkml.kernel.org/r/c5e23b45562373d632fccb8bc04e563abba4dd1d.camel@perches.comSigned-off-by: Joe Perches <joe@perches.com>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull timer fixes from Thomas Gleixner:
 "A time namespace fix and a matching selftest. The futex absolute
  timeouts which are based on CLOCK_MONOTONIC require time namespace
  corrected. This was missed in the original time namesapce support"

* tag 'timers-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  selftests/timens: Add a test for futex()
  futex: Adjust absolute futex timeouts with per time namespace offset

Pull scheduler fixes from Thomas Gleixner:
 "Two scheduler fixes:

   - A trivial build fix for sched_feat() to compile correctly with
     CONFIG_JUMP_LABEL=n

   - Replace a zero lenght array with a flexible array"

* tag 'sched-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/features: Fix !CONFIG_JUMP_LABEL case
  sched: Replace zero-length array with flexible-array

Pull perf fix from Thomas Gleixner:
 "A single fix to compute the field offset of the SNOOPX bit in the data
  source bitmask of perf events correctly"

* tag 'perf-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: correct SNOOPX field offset

Pull locking fix from Thomas Gleixner:
 "Just a trivial fix for kernel-doc warnings"

* tag 'locking-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  locking/seqlocks: Fix kernel-doc warnings

Pull NTB fixes from Jon Mason.

* tag 'ntb-5.10' of git://github.com/jonmason/ntb:
  NTB: Use struct_size() helper in devm_kzalloc()
  ntb: intel: Fix memleak in intel_ntb_pci_probe
  NTB: hw: amd: fix an issue about leak system resources

Pull i2c fix from Wolfram Sang:
 "Regression fix for rc1 and stable kernels as well"

* 'i2c/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: core: Restore acpi_walk_dep_device_list() getting called after registering the ACPI i2c devs

Pull more cifs updates from Steve French:
 "Add support for stat of various special file types (WSL reparse points
  for char, block, fifo)"

* tag '5.10-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: update internal module version number
  smb3: add some missing definitions from MS-FSCC
  smb3: remove two unused variables
  smb3: add support for stat of WSL reparse points for special file types

Pull more parisc updates from Helge Deller:

 - During this merge window O_NONBLOCK was changed to become 000200000,
   but we missed that the syscalls timerfd_create(), signalfd4(),
   eventfd2(), pipe2(), inotify_init1() and userfaultfd() do a strict
   bit-wise check of the flags parameter.

   To provide backward compatibility with existing userspace we
   introduce parisc specific wrappers for those syscalls which filter
   out the old O_NONBLOCK value and replaces it with the new one.

 - Prevent HIL bus driver to get stuck when keyboard or mouse isn't
   attached

 - Improve error return codes when setting rtc time

 - Minor documentation fix in pata_ns87415.c

* 'parisc-5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  ata: pata_ns87415.c: Document support on parisc with superio chip
  parisc: Add wrapper syscalls to fix O_NONBLOCK flag usage
  hil/parisc: Disable HIL driver when it gets stuck
  parisc: Improve error return codes when setting rtc time

Pull more xen updates from Juergen Gross:

 - a series for the Xen pv block drivers adding module parameters for
   better control of resource usge

 - a cleanup series for the Xen event driver

* tag 'for-linus-5.10b-rc1c-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  Documentation: add xen.fifo_events kernel parameter description
  xen/events: unmask a fifo event channel only if it was masked
  xen/events: only register debug interrupt for 2-level events
  xen/events: make struct irq_info private to events_base.c
  xen: remove no longer used functions
  xen-blkfront: Apply changed parameter name to the document
  xen-blkfront: add a parameter for disabling of persistent grants
  xen-blkback: add a parameter for disabling of persistent grants

Pull SafeSetID updates from Micah Morton:
 "The changes are mostly contained to within the SafeSetID LSM, with the
  exception of a few 1-line changes to change some ns_capable() calls to
  ns_capable_setid() -- causing a flag (CAP_OPT_INSETID) to be set that
  is examined by SafeSetID code and nothing else in the kernel.

  The changes to SafeSetID internally allow for setting up GID
  transition security policies, as already existed for UIDs"

* tag 'safesetid-5.10' of git://github.com/micah-morton/linux:
  LSM: SafeSetID: Fix warnings reported by test bot
  LSM: SafeSetID: Add GID security policy handling
  LSM: Signal to SafeSetID when setting group IDs

Pull random32 updates from Willy Tarreau:
 "Make prandom_u32() less predictable.

  This is the cleanup of the latest series of prandom_u32
  experimentations consisting in using SipHash instead of Tausworthe to
  produce the randoms used by the network stack.

  The changes to the files were kept minimal, and the controversial
  commit that used to take noise from the fast_pool (f227e3ec) was
  reverted. Instead, a dedicated "net_rand_noise" per_cpu variable is
  fed from various sources of activities (networking, scheduling) to
  perturb the SipHash state using fast, non-trivially predictable data,
  instead of keeping it fully deterministic. The goal is essentially to
  make any occasional memory leakage or brute-force attempt useless.

  The resulting code was verified to be very slightly faster on x86_64
  than what is was with the controversial commit above, though this
  remains barely above measurement noise. It was also tested on i386 and
  arm, and build- tested only on arm64"

Link: https://lore.kernel.org/netdev/20200808152628.GA27941@SDF.ORG/

* tag '20201024-v4-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wtarreau/prandom:
  random32: add a selftest for the prandom32 code
  random32: add noise from network and scheduling activity
  random32: make prandom_u32() output unpredictable

Commit 21653a41 ("i2c: core: Call i2c_acpi_install_space_handler()
before i2c_acpi_register_devices()")'s intention was to only move the
acpi_install_address_space_handler() call to the point before where
the ACPI declared i2c-children of the adapter where instantiated by
i2c_acpi_register_devices().

But i2c_acpi_install_space_handler() had a call to
acpi_walk_dep_device_list() hidden (that is I missed it) at the end
of it, so as an unwanted side-effect now acpi_walk_dep_device_list()
was also being called before i2c_acpi_register_devices().

Move the acpi_walk_dep_device_list() call to the end of
i2c_acpi_register_devices(), so that it is once again called *after*
the i2c_client-s hanging of the adapter have been created.

This fixes the Microsoft Surface Go 2 hanging at boot.

Fixes: 21653a41 ("i2c: core: Call i2c_acpi_install_space_handler() before i2c_acpi_register_devices()")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209627Reported-by: Rainer Finke <rainer@finke.cc>
Reported-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Suggested-by: Maximilian Luz <luzmaximilian@gmail.com>
Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Pull block fixes from Jens Axboe:

 - NVMe pull request from Christoph
     - rdma error handling fixes (Chao Leng)
     - fc error handling and reconnect fixes (James Smart)
     - fix the qid displace when tracing ioctl command (Keith Busch)
     - don't use BLK_MQ_REQ_NOWAIT for passthru (Chaitanya Kulkarni)
     - fix MTDT for passthru (Logan Gunthorpe)
     - blacklist Write Same on more devices (Kai-Heng Feng)
     - fix an uninitialized work struct (zhenwei pi)"

 - lightnvm out-of-bounds fix (Colin)

 - SG allocation leak fix (Doug)

 - rnbd fixes (Gioh, Guoqing, Jack)

 - zone error translation fixes (Keith)

 - kerneldoc markup fix (Mauro)

 - zram lockdep fix (Peter)

 - Kill unused io_context members (Yufen)

 - NUMA memory allocation cleanup (Xianting)

 - NBD config wakeup fix (Xiubo)

* tag 'block-5.10-2020-10-24' of git://git.kernel.dk/linux-block: (27 commits)
  block: blk-mq: fix a kernel-doc markup
  nvme-fc: shorten reconnect delay if possible for FC
  nvme-fc: wait for queues to freeze before calling update_hr_hw_queues
  nvme-fc: fix error loop in create_hw_io_queues
  nvme-fc: fix io timeout to abort I/O
  null_blk: use zone status for max active/open
  nvmet: don't use BLK_MQ_REQ_NOWAIT for passthru
  nvmet: cleanup nvmet_passthru_map_sg()
  nvmet: limit passthru MTDS by BIO_MAX_PAGES
  nvmet: fix uninitialized work for zero kato
  nvme-pci: disable Write Zeroes on Sandisk Skyhawk
  nvme: use queuedata for nvme_req_qid
  nvme-rdma: fix crash due to incorrect cqe
  nvme-rdma: fix crash when connect rejected
  block: remove unused members for io_context
  blk-mq: remove the calling of local_memory_node()
  zram: Fix __zram_bvec_{read,write}() locking order
  skd_main: remove unused including <linux/version.h>
  sgl_alloc_order: fix memory leak
  lightnvm: fix out-of-bounds write to array devices->info[]
  ...

Pull io_uring fixes from Jens Axboe:

 - fsize was missed in previous unification of work flags

 - Few fixes cleaning up the flags unification creds cases (Pavel)

 - Fix NUMA affinities for completely unplugged/replugged node for io-wq

 - Two fallout fixes from the set_fs changes. One local to io_uring, one
   for the splice entry point that io_uring uses.

 - Linked timeout fixes (Pavel)

 - Removal of ->flush() ->files work-around that we don't need anymore
   with referenced files (Pavel)

 - Various cleanups (Pavel)

* tag 'io_uring-5.10-2020-10-24' of git://git.kernel.dk/linux-block:
  splice: change exported internal do_splice() helper to take kernel offset
  io_uring: make loop_rw_iter() use original user supplied pointers
  io_uring: remove req cancel in ->flush()
  io-wq: re-set NUMA node affinities if CPUs come online
  io_uring: don't reuse linked_timeout
  io_uring: unify fsize with def->work_flags
  io_uring: fix racy REQ_F_LINK_TIMEOUT clearing
  io_uring: do poll's hash_node init in common code
  io_uring: inline io_poll_task_handler()
  io_uring: remove extra ->file check in poll prep
  io_uring: make cached_cq_overflow non atomic_t
  io_uring: inline io_fail_links()
  io_uring: kill ref get/drop in personality init
  io_uring: flags-based creds init in queue

Pull libata fixes from Jens Axboe:
 "Two minor libata fixes:

   - Fix a DMA boundary mask regression for sata_rcar (Geert)

   - kerneldoc markup fix (Mauro)"

* tag 'libata-5.10-2020-10-24' of git://git.kernel.dk/linux-block:
  ata: fix some kernel-doc markups
  ata: sata_rcar: Fix DMA boundary mask

Pull misc vfs updates from Al Viro:
 "Assorted stuff all over the place (the largest group here is
  Christoph's stat cleanups)"

* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fs: remove KSTAT_QUERY_FLAGS
  fs: remove vfs_stat_set_lookup_flags
  fs: move vfs_fstatat out of line
  fs: implement vfs_stat and vfs_lstat in terms of vfs_fstatat
  fs: remove vfs_statx_fd
  fs: omfs: use kmemdup() rather than kmalloc+memcpy
  [PATCH] reduce boilerplate in fsid handling
  fs: Remove duplicated flag O_NDELAY occurring twice in VALID_OPEN_FLAGS
  selftests: mount: add nosymfollow tests
  Add a "nosymfollow" mount option.

Pull dma-mapping fixes from Christoph Hellwig:

 - document the new dma_{alloc,free}_pages() API

 - two fixups for the dma-mapping.h split

* tag 'dma-mapping-5.10-1' of git://git.infradead.org/users/hch/dma-mapping:
  dma-mapping: document dma_{alloc,free}_pages
  dma-mapping: move more functions to dma-map-ops.h
  ARM/sa1111: add a missing include of dma-map-ops.h