- 03 Apr, 2019 26 commits
-
-
Michal Suchanek authored
commit cb3d6759 upstream. Check what firmware told us and enable/disable the barrier_nospec as appropriate. We err on the side of enabling the barrier, as it's no-op on older systems, see the comment for more detail. Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Michal Suchanek authored
commit 815069ca upstream. Note that unlike RFI which is patched only in kernel the nospec state reflects settings at the time the module was loaded. Iterating all modules and re-patching every time the settings change is not implemented. Based on lwsync patching. Signed-off-by:
Michal Suchanek <msuchanek@suse.de> Signed-off-by:
-
Michal Suchanek authored
commit 2eea7f06 upstream. Based on the RFI patching. This is required to be able to disable the speculation barrier. Only one barrier type is supported and it does nothing when the firmware does not enable it. Also re-patching modules is not supported So the only meaningful thing that can be done is patching out the speculation barrier at boot when the user says it is not wanted. Signed-off-by:
-
Eric Dumazet authored
commit 9180bb4f upstream. In my latest patch I missed one rcu_read_unlock(), in case device is down. Fixes: 4477138f ("tun: properly test for IFF_UP") Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
syzbot <syzkaller@googlegroups.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 4477138f ] Same reasons than the ones explained in commit 4179cb5a ("vxlan: test dev->flags & IFF_UP before calling netif_rx()") netif_rx_ni() or napi_gro_frags() must be called under a strict contract. At device dismantle phase, core networking clears IFF_UP and flush_all_backlogs() is called after rcu grace period to make sure no incoming packet might be in a cpu backlog and still referencing the device. A similar protocol is used for gro layer. Most drivers call netif_rx() from their interrupt handler, and since the interrupts are disabled at device dismantle, netif_rx() does not have to check dev->flags & IFF_UP Virtual drivers do not have this guarantee, and must therefore make the check themselves. Fixes: 1bd4978a ("tun: honor IFF_UP in tun_get_user()") Signed-off-by:
-
Finn Thain authored
[ Upstream commit bb9e5c5b ] The bug that Stan reported is as follows. After a restart, a 16-bit NIC may be incorrectly identified as a 32-bit NIC and stop working. mac8390 slot.E: Memory length resource not found, probing mac8390 slot.E: Farallon EtherMac II-C (type farallon) mac8390 slot.E: MAC 00:00:c5:30:c2:99, IRQ 61, 32 KB shared memory at 0xfeed0000, 32-bit access. The bug never arises after a cold start and only intermittently after a warm start. (I didn't investigate why the bug is intermittent.) It turns out that memcpy_toio() is deprecated and memcmp_withio() also has issues. Replacing these calls with mmio accessors fixes the problem. Reported-and-tested-by:
Stan Johnson <userm57@yahoo.com> Fixes: 2964db0f ("m68k: Mac DP8390 update") Signed-off-by:
Finn Thain <fthain@telegraphics.com.au> Signed-off-by:
-
Dmitry Bogdanov authored
[ Upstream commit a7faaa0c ] TCP/UDP checksum validity was propagated to skb only if IP checksum is valid. But for IPv6 there is no validity as there is no checksum in IPv6. This patch propagates TCP/UDP checksum validity regardless of IP checksum. Fixes: 018423e9 ("net: ethernet: aquantia: Add ring support code") Signed-off-by:
Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by:
Nikita Danilov <nikita.danilov@aquantia.com> Signed-off-by:
Dmitry Bogdanov <dmitry.bogdanov@aquantia.com> Signed-off-by:
-
Xin Long authored
[ Upstream commit 273160ff ] sctp_hdr(skb) only works when skb->transport_header is set properly. But in Netfilter, skb->transport_header for ipv6 is not guaranteed to be right value for sctphdr. It would cause to fail to check the checksum for sctp packets. So fix it by using offset, which is always right in all places. v1->v2: - Fix the changelog. Fixes: e6d8b64b ("net: sctp: fix and consolidate SCTP checksumming code") Reported-by:
Li Shuang <shuali@redhat.com> Signed-off-by:
Xin Long <lucien.xin@gmail.com> Signed-off-by:
-
Zhiqiang Liu authored
[ Upstream commit cc4807bb ] Commit ad6c9986 ("vxlan: Fix GRO cells race condition between receive and link delete") fixed a race condition for the typical case a vxlan device is dismantled from the current netns. But if a netns is dismantled, vxlan_destroy_tunnels() is called to schedule a unregister_netdevice_queue() of all the vxlan tunnels that are related to this netns. In vxlan_destroy_tunnels(), gro_cells_destroy() is called and finished before unregister_netdevice_queue(). This means that the gro_cells_destroy() call is done too soon, for the same reasons explained in above commit. So we need to fully respect the RCU rules, and thus must remove the gro_cells_destroy() call or risk use after-free. Fixes: 58ce31cc ("vxlan: GRO support at tunnel layer") Signed-off-by:
Suanming.Mou <mousuanming@huawei.com> Suggested-by:
Eric Dumazet <eric.dumazet@gmail.com> Reviewed-by:
Stefano Brivio <sbrivio@redhat.com> Reviewed-by:
Zhiqiang Liu <liuzhiqiang26@huawei.com> Signed-off-by:
-
Dean Nelson authored
[ Upstream commit cd35ef91 ] For the non-XDP case, commit 77322538 ("net: thunderx: Optimize page recycling for XDP") added code to nicvf_free_rbdr() that, when releasing the additional receive buffer page reference held for recycling, repeatedly calls put_page() until the page's _refcount goes to zero. Which results in the page being freed. This is not okay if the page's _refcount was greater than 1 (in the non-XDP case), because nicvf_free_rbdr() should not be subtracting more than what nicvf_alloc_page() had previously added to the page's _refcount, which was only 1 (in the non-XDP case). This can arise if a received packet is still being processed and the receive buffer (i.e., skb->head) has not yet been freed via skb_free_head() when nicvf_free_rbdr() is spinning through the aforementioned put_page() loop. If this should occur, when the received packet finishes processing and skb_free_head() is called, various problems can ensue. Exactly what, depends on whether the page has already been reallocated or not, anything from "BUG: Bad page state ... ", to "Unable to handle kernel NULL pointer dereference ..." or "Unable to handle kernel paging request...". So this patch changes nicvf_free_rbdr() to only call put_page() once for pages held for recycling (in the non-XDP case). Fixes: 77322538 ("net: thunderx: Optimize page recycling for XDP") Signed-off-by:
Dean Nelson <dnelson@redhat.com> Signed-off-by:
-
Dean Nelson authored
[ Upstream commit b3e20806 ] Commit 77322538 ("net: thunderx: Optimize page recycling for XDP") added code to nicvf_alloc_page() that inadvertently disables receive buffer page recycling for the non-XDP case by always NULL'ng the page pointer. This patch corrects two if-conditionals to allow for the recycling of non-XDP mode pages by only setting the page pointer to NULL when the page is not ready for recycling. Fixes: 77322538 ("net: thunderx: Optimize page recycling for XDP") Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 89e41309 ] When a dual stack tcp listener accepts an ipv4 flow, it should not attempt to use an ipv6 header or tcp_v6_iif() helper. Fixes: 1397ed35 ("ipv6: add flowinfo for tcp6 pkt_options for all cases") Fixes: df3687ff ("ipv6: add the IPV6_FL_F_REFLECT flag to IPV6_FL_A_GET") Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
Herbert Xu authored
[ Upstream commit 408f13ef ] As it stands if a shrink is delayed because of an outstanding rehash, we will go into a rescheduling loop without ever doing the rehash. This patch fixes this by still carrying out the rehash and then rescheduling so that we can shrink after the completion of the rehash should it still be necessary. The return value of EEXIST captures this case and other cases (e.g., another thread expanded/rehashed the table at the same time) where we should still proceed with the rehash. Fixes: da20420f ("rhashtable: Add nested tables") Reported-by:
Josh Elsasser <jelsasser@appneta.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Tested-by:
-
Maxime Chevallier authored
[ Upstream commit a4dc6a49 ] When using fanouts with AF_PACKET, the demux functions such as fanout_demux_cpu will return an index in the fanout socket array, which corresponds to the selected socket. The ordering of this array depends on the order the sockets were added to a given fanout group, so for FANOUT_CPU this means sockets are bound to cpus in the order they are configured, which is OK. However, when stopping then restarting the interface these sockets are bound to, the sockets are reassigned to the fanout group in the reverse order, due to the fact that they were inserted at the head of the interface's AF_PACKET socket list. This means that traffic that was directed to the first socket in the fanout group is now directed to the last one after an interface restart. In the case of FANOUT_CPU, traffic from CPU0 will be directed to the socket that used to receive traffic from the last CPU after an interface restart. This commit introduces a helper to add a socket at the tail of a list, then uses it to register AF_PACKET sockets. Note that this changes the order in which sockets are listed in /proc and with sock_diag. Fixes: dc99f600 ("packet: Add fanout support") Signed-off-by:
Maxime Chevallier <maxime.chevallier@bootlin.com> Acked-by:
Willem de Bruijn <willemb@google.com> Signed-off-by:
-
YueHaibing authored
[ Upstream commit a3e23f71 ] In netdev_queue_add_kobject and rx_queue_add_kobject, if sysfs_create_group failed, kobject_put will call netdev_queue_release to decrease dev refcont, however dev_hold has not be called. So we will see this while unregistering dev: unregister_netdevice: waiting for bcsh0 to become free. Usage count = -1 Reported-by:
Hulk Robot <hulkci@huawei.com> Fixes: d0d66837 ("net: don't decrement kobj reference count on init failure") Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
-
Aaro Koskinen authored
[ Upstream commit 223a960c ] When using 16K DMA buffers and ring mode, the DES3 refill is not working correctly as the function is using a bogus pointer for checking the private data. As a result stale pointers will remain in the RX descriptor ring, so DMA will now likely overwrite/corrupt some already freed memory. As simple reproducer, just receive some UDP traffic: # ifconfig eth0 down; ifconfig eth0 mtu 9000; ifconfig eth0 up # iperf3 -c 192.168.253.40 -u -b 0 -R If you didn't crash by now check the RX descriptors to find non-contiguous RX buffers: cat /sys/kernel/debug/stmmaceth/eth0/descriptors_status [...] 1 [0x2be5020]: 0xa3220321 0x9ffc1ffc 0x72d70082 0x130e207e ^^^^^^^^^^^^^^^^^^^^^ 2 [0x2be5040]: 0xa3220321 0x9ffc1ffc 0x72998082 0x1311a07e ^^^^^^^^^^^^^^^^^^^^^ A simple ping test will now report bad data: # ping -s 8200 192.168.253.40 PING 192.168.253.40 (192.168.253.40) 8200(8228) bytes of data. 8208 bytes from 192.168.253.40: icmp_seq=1 ttl=64 time=1.00 ms wrong data byte #8144 should be 0xd0 but was 0x88 Fix the wrong pointer. Also we must refill DES3 only if the DMA buffer size is 16K. Fixes: 54139cf3 ("net: stmmac: adding multiple buffers for rx") Signed-off-by:
Aaro Koskinen <aaro.koskinen@nokia.com> Acked-by:
Jose Abreu <joabreu@synopsys.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit e5dcc0c3 ] rose_write_internal() uses a temp buffer of 100 bytes, but a manual inspection showed that given arbitrary input, rose_create_facilities() can fill up to 110 bytes. Lets use a tailroom of 256 bytes for peace of mind, and remove the bounce buffer : we can simply allocate a big enough skb and adjust its length as needed. syzbot report : BUG: KASAN: stack-out-of-bounds in memcpy include/linux/string.h:352 [inline] BUG: KASAN: stack-out-of-bounds in rose_create_facilities net/rose/rose_subr.c:521 [inline] BUG: KASAN: stack-out-of-bounds in rose_write_internal+0x597/0x15d0 net/rose/rose_subr.c:116 Write of size 7 at addr ffff88808b1ffbef by task syz-executor.0/24854 CPU: 0 PID: 24854 Comm: syz-executor.0 Not tainted 5.0.0+ #97 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x172/0x1f0 lib/dump_stack.c:113 print_address_description.cold+0x7c/0x20d mm/kasan/report.c:187 kasan_report.cold+0x1b/0x40 mm/kasan/report.c:317 check_memory_region_inline mm/kasan/generic.c:185 [inline] check_memory_region+0x123/0x190 mm/kasan/generic.c:191 memcpy+0x38/0x50 mm/kasan/common.c:131 memcpy include/linux/string.h:352 [inline] rose_create_facilities net/rose/rose_subr.c:521 [inline] rose_write_internal+0x597/0x15d0 net/rose/rose_subr.c:116 rose_connect+0x7cb/0x1510 net/rose/af_rose.c:826 __sys_connect+0x266/0x330 net/socket.c:1685 __do_sys_connect net/socket.c:1696 [inline] __se_sys_connect net/socket.c:1693 [inline] __x64_sys_connect+0x73/0xb0 net/socket.c:1693 do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x458079 Code: ad b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007f47b8d9dc78 EFLAGS: 00000246 ORIG_RAX: 000000000000002a RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 0000000000458079 RDX: 000000000000001c RSI: 0000000020000040 RDI: 0000000000000004 RBP: 000000000073bf00 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00007f47b8d9e6d4 R13: 00000000004be4a4 R14: 00000000004ceca8 R15: 00000000ffffffff The buggy address belongs to the page: page:ffffea00022c7fc0 count:0 mapcount:0 mapping:0000000000000000 index:0x0 flags: 0x1fffc0000000000() raw: 01fffc0000000000 0000000000000000 ffffffff022c0101 0000000000000000 raw: 0000000000000000 0000000000000000 00000000ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff88808b1ffa80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff88808b1ffb00: 00 00 00 00 00 00 00 00 f1 f1 f1 f1 00 00 00 03 >ffff88808b1ffb80: f2 f2 00 00 00 00 00 00 00 00 00 00 00 00 04 f3 ^ ffff88808b1ffc00: f3 f3 f3 f3 00 00 00 00 00 00 00 00 00 00 00 00 ffff88808b1ffc80: 00 00 00 00 00 00 00 f1 f1 f1 f1 f1 f1 01 f2 01 Signed-off-by:
-
Christoph Paasch authored
[ Upstream commit 398f0132 ] Since commit fc62814d ("net/packet: fix 4gb buffer limit due to overflow check") one can now allocate packet ring buffers >= UINT_MAX. However, syzkaller found that that triggers a warning: [ 21.100000] WARNING: CPU: 2 PID: 2075 at mm/page_alloc.c:4584 __alloc_pages_nod0 [ 21.101490] Modules linked in: [ 21.101921] CPU: 2 PID: 2075 Comm: syz-executor.0 Not tainted 5.0.0 #146 [ 21.102784] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 0.5.1 01/01/2011 [ 21.103887] RIP: 0010:__alloc_pages_nodemask+0x2a0/0x630 [ 21.104640] Code: fe ff ff 65 48 8b 04 25 c0 de 01 00 48 05 90 0f 00 00 41 bd 01 00 00 00 48 89 44 24 48 e9 9c fe 3 [ 21.107121] RSP: 0018:ffff88805e1cf920 EFLAGS: 00010246 [ 21.107819] RAX: 0000000000000000 RBX: ffffffff85a488a0 RCX: 0000000000000000 [ 21.108753] RDX: 0000000000000000 RSI: dffffc0000000000 RDI: 0000000000000000 [ 21.109699] RBP: 1ffff1100bc39f28 R08: ffffed100bcefb67 R09: ffffed100bcefb67 [ 21.110646] R10: 0000000000000001 R11: ffffed100bcefb66 R12: 000000000000000d [ 21.111623] R13: 0000000000000000 R14: ffff88805e77d888 R15: 000000000000000d [ 21.112552] FS: 00007f7c7de05700(0000) GS:ffff88806d100000(0000) knlGS:0000000000000000 [ 21.113612] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 21.114405] CR2: 000000000065c000 CR3: 000000005e58e006 CR4: 00000000001606e0 [ 21.115367] Call Trace: [ 21.115705] ? __alloc_pages_slowpath+0x21c0/0x21c0 [ 21.116362] alloc_pages_current+0xac/0x1e0 [ 21.116923] kmalloc_order+0x18/0x70 [ 21.117393] kmalloc_order_trace+0x18/0x110 [ 21.117949] packet_set_ring+0x9d5/0x1770 [ 21.118524] ? packet_rcv_spkt+0x440/0x440 [ 21.119094] ? lock_downgrade+0x620/0x620 [ 21.119646] ? __might_fault+0x177/0x1b0 [ 21.120177] packet_setsockopt+0x981/0x2940 [ 21.120753] ? __fget+0x2fb/0x4b0 [ 21.121209] ? packet_release+0xab0/0xab0 [ 21.121740] ? sock_has_perm+0x1cd/0x260 [ 21.122297] ? selinux_secmark_relabel_packet+0xd0/0xd0 [ 21.123013] ? __fget+0x324/0x4b0 [ 21.123451] ? selinux_netlbl_socket_setsockopt+0x101/0x320 [ 21.124186] ? selinux_netlbl_sock_rcv_skb+0x3a0/0x3a0 [ 21.124908] ? __lock_acquire+0x529/0x3200 [ 21.125453] ? selinux_socket_setsockopt+0x5d/0x70 [ 21.126075] ? __sys_setsockopt+0x131/0x210 [ 21.126533] ? packet_release+0xab0/0xab0 [ 21.127004] __sys_setsockopt+0x131/0x210 [ 21.127449] ? kernel_accept+0x2f0/0x2f0 [ 21.127911] ? ret_from_fork+0x8/0x50 [ 21.128313] ? do_raw_spin_lock+0x11b/0x280 [ 21.128800] __x64_sys_setsockopt+0xba/0x150 [ 21.129271] ? lockdep_hardirqs_on+0x37f/0x560 [ 21.129769] do_syscall_64+0x9f/0x450 [ 21.130182] entry_SYSCALL_64_after_hwframe+0x49/0xbe We should allocate with __GFP_NOWARN to handle this. Cc: Kal Conley <kal.conley@dectris.com> Cc: Andrey Konovalov <andreyknvl@google.com> Fixes: fc62814d ("net/packet: fix 4gb buffer limit due to overflow check") Signed-off-by:
Christoph Paasch <cpaasch@apple.com> Signed-off-by:
-
Paolo Abeni authored
[ Upstream commit 0b91bce1 ] Christoph reported a stall while peeking datagram with an offset when busy polling is enabled. __skb_try_recv_datagram() uses as the loop termination condition 'queue empty'. When peeking, the socket queue can be not empty, even when no additional packets are received. Address the issue explicitly checking for receive queue changes, as currently done by __skb_wait_for_more_packets(). Fixes: 2b5cd0df ("net: Change return type of sk_busy_loop from bool to void") Reported-and-tested-by:
Paolo Abeni <pabeni@redhat.com> Signed-off-by:
-
Bjorn Helgaas authored
[ Upstream commit fae846e2 ] The device ID alone does not uniquely identify a device. Test both the vendor and device ID to make sure we don't mistakenly think some other vendor's 0xB410 device is a Digium HFC4S. Also, instead of the bare hex ID, use the same constant (PCI_DEVICE_ID_DIGIUM_HFC4S) used in the device ID table. No functional change intended. Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Signed-off-by:
-
YueHaibing authored
[ Upstream commit ceabee6c ] In genl_register_family(), when idr_alloc() fails, we forget to free the memory we possibly allocate for family->attrbuf. Reported-by:
Kirill Tkhai <ktkhai@virtuozzo.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit e0aa6770 ] When a dual stack dccp listener accepts an ipv4 flow, it should not attempt to use an ipv6 header or inet6_iif() helper. Fixes: 3df80d93 ("[DCCP]: Introduce DCCPv6") Signed-off-by:
-
Bhadram Varka authored
[ Upstream commit a830405e ] Currently stmmac driver not copying the valid ethernet MAC address to MAC registers. This patch takes care of updating the MAC register with MAC address. Signed-off-by:
Bhadram Varka <vbhadram@nvidia.com> Signed-off-by:
Sasha Levin <sashal@kernel.org> Signed-off-by:
-
Christoffer Dall authored
[ Upstream commit ace6033e ] User space Android code identifies pixclock == 0 as a sign for emulation and will set the frame rate to 60 fps when reading this value, which is the desired outcome. Signed-off-by:
Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by:
Peter Maydell <peter.maydell@linaro.org> Signed-off-by:
Roman Kiryanov <rkir@google.com> Signed-off-by:
Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by:
-
Marcel Holtmann authored
commit 7c9cbd0b upstream. The function l2cap_get_conf_opt will return L2CAP_CONF_OPT_SIZE + opt->len as length value. The opt->len however is in control over the remote user and can be used by an attacker to gain access beyond the bounds of the actual packet. To prevent any potential leak of heap memory, it is enough to check that the resulting len calculation after calling l2cap_get_conf_opt is not below zero. A well formed packet will always return >= 0 here and will end with the length value being zero after the last option has been parsed. In case of malformed packets messing with the opt->len field the length value will become negative. If that is the case, then just abort and ignore the option. In case an attacker uses a too short opt->len value, then garbage will be parsed, but that is protected by the unknown option handling and also the option parameter size checks. Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Reviewed-by:
Johan Hedberg <johan.hedberg@intel.com> Signed-off-by:
-
Marcel Holtmann authored
commit af3d5d1c upstream. When doing option parsing for standard type values of 1, 2 or 4 octets, the value is converted directly into a variable instead of a pointer. To avoid being tricked into being a pointer, check that for these option types that sizes actually match. In L2CAP every option is fixed size and thus it is prudent anyway to ensure that the remote side sends us the right option size along with option paramters. If the option size is not matching the option type, then that option is silently ignored. It is a protocol violation and instead of trying to give the remote attacker any further hints just pretend that option is not present and proceed with the default values. Implementation following the specification and its qualification procedures will always use the correct size and thus not being impacted here. To keep the code readable and consistent accross all options, a few cosmetic changes were also required. Signed-off-by:
-
- 27 Mar, 2019 14 commits
-
-
Greg Kroah-Hartman authored
-
Arnd Bergmann authored
commit 6707ba01 upstream. The way that 'strncat' is used here raised a warning in gcc-8: drivers/net/wireless/ath/ath10k/wmi.c: In function 'ath10k_wmi_tpc_stats_final_disp_tables': drivers/net/wireless/ath/ath10k/wmi.c:4649:4: error: 'strncat' output truncated before terminating nul copying as many bytes from a string as its length [-Werror=stringop-truncation] Effectively, this is simply a strcat() but the use of strncat() suggests some form of overflow check. Regardless of whether this might actually overflow, using strlcat() instead of strncat() avoids the warning and makes the code more robust. Fixes: bc64d052 ("ath10k: debugfs support to get final TPC stats for 10.4 variants") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Baolin Wang authored
commit f25a646f upstream. Fix incorrect return value. Signed-off-by:
Baolin Wang <baolin.wang@linaro.org> Signed-off-by:
Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by:
-
Enric Balletbo i Serra authored
commit 5fb5caee upstream. Before this patch the enable signal was set before the PWM signal and vice-versa on power off. This sequence is wrong, at least, it is on the different panels datasheets that I checked, so I inverted the sequence to follow the specs. For reference the following panels have the mentioned sequence: - N133HSE-EA1 (Innolux) - N116BGE (Innolux) - N156BGE-L21 (Innolux) - B101EAN0 (Auo) - B101AW03 (Auo) - LTN101NT05 (Samsung) - CLAA101WA01A (Chunghwa) Signed-off-by:
Enric Balletbo i Serra <enric.balletbo@collabora.com> Acked-by:
Daniel Thompson <daniel.thompson@linaro.org> Acked-by:
Jingoo Han <jingoohan1@gmail.com> Acked-by:
Thierry Reding <thierry.reding@gmail.com> Signed-off-by:
Lee Jones <lee.jones@linaro.org> Signed-off-by:
-
Jules Maselbas authored
commit 1b5d43cf upstream. This patch prevents the 'global_tunables_lock' mutex from being unlocked before being locked. This mutex is not locked if the sugov_kthread_create() function fails. Signed-off-by:
Jules Maselbas <jules.maselbas@arm.com> Acked-by:
Peter Zijlstra <peterz@infradead.org> Cc: Chris Redpath <chris.redpath@arm.com> Cc: Dietmar Eggermann <dietmar.eggemann@arm.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Patrick Bellasi <patrick.bellasi@arm.com> Cc: Stephen Kyle <stephen.kyle@arm.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Cc: nd@arm.com Link: http://lkml.kernel.org/r/20180329144301.38419-1-jules.maselbas@arm.comSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Baolin Wang authored
commit 36d46cdb upstream. If we convert one large time values to rtc_time, in the original formula 'days * 86400' can be overflowed in 'unsigned int' type to make the formula get one incorrect remain seconds value. Thus we can use div_s64_rem() function to avoid this situation. Signed-off-by:
Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by:
-
Kishon Vijay Abraham I authored
commit b330104f upstream. After commit 72328883 ("of: restrict DMA configuration"), of_dma_configure() doesn't configure the coherent_dma_mask/dma_mask of endpoint function device (since it doesn't have a DT node associated with and hence no dma-ranges property), resulting in dma_alloc_coherent() (used in pci_epf_alloc_space()) to fail. Fix it by making dma_alloc_coherent() use EPC's device for allocating memory address. Link: http://lkml.kernel.org/r/64d63468-d28f-8fcd-a6f3-cf2a6401c8cb@ti.comSigned-off-by:
Kishon Vijay Abraham I <kishon@ti.com> [lorenzo.pieralisi@arm.com: tweaked commit log] Signed-off-by:
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Robin Murphy <robin.murphy@arm.com> Cc: Rob Herring <robh@kernel.org> Cc: Christoph Hellwig <hch@lst.de> Tested-by:
Cyrille Pitchen <cyrille.pitchen@free-electrons.com> Tested-by:
Niklas Cassel <niklas.cassel@axis.com> Reviewed-by:
Robin Murphy <robin.murphy@arm.com> Signed-off-by:
-
Niklas Cassel authored
commit 1cab826b upstream. Certain registers that pcie-designware-ep tries to write to are read-only registers. However, these registers can become read/write if we first enable the DBI_RO_WR_EN bit. Set/unset the DBI_RO_WR_EN bit before/after writing these registers. Tested-by:
Gustavo Pimentel <gustavo.pimentel@synopsys.com> Signed-off-by:
Joao Pinto <jpinto@synopsys.com> Signed-off-by:
-
Niklas Cassel authored
commit 099a95f3 upstream. Previously, dw_pcie_ep_set_msi() wrote all bits in the Message Control register, thus overwriting the PCI_MSI_FLAGS_64BIT bit. By clearing the PCI_MSI_FLAGS_64BIT bit, we break MSI on systems where the RC has set a 64 bit MSI address. Fix dw_pcie_ep_set_msi() so that it only sets MMC bits. Tested-by:
-
kehuanlin authored
commit 83dc7e3d upstream. Since the command type of UTRD in UFS 2.1 specification is the same with UFS 2.0. And it assumes the future UFS specification will follow the same definition. Signed-off-by:
kehuanlin <kehuanlin@pinecone.net> Reviewed-by:
Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Andrey Konovalov authored
commit 32fd87b3 upstream. When cleaning up the configurations, make sure we only free the number of configurations and interfaces that we could have allocated. Reported-by:
Andrey Konovalov <andreyknvl@google.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Peter Zijlstra authored
commit 3f329570 upstream. The current int_sqrt() computation is sub-optimal for the case of small @x. Which is the interesting case when we're going to do cumulative distribution functions on idle times, which we assume to be a random variable, where the target residency of the deepest idle state gives an upper bound on the variable (5e6ns on recent Intel chips). In the case of small @x, the compute loop: while (m != 0) { b = y + m; y >>= 1; if (x >= b) { x -= b; y += m; } m >>= 2; } can be reduced to: while (m > x) m >>= 2; Because y==0, b==m and until x>=m y will remain 0. And while this is computationally equivalent, it runs much faster because there's less code, in particular less branches. cycles: branches: branch-misses: OLD: hot: 45.109444 +- 0.044117 44.333392 +- 0.002254 0.018723 +- 0.000593 cold: 187.737379 +- 0.156678 44.333407 +- 0.002254 6.272844 +- 0.004305 PRE: hot: 67.937492 +- 0.064124 66.999535 +- 0.000488 0.066720 +- 0.001113 cold: 232.004379 +- 0.332811 66.999527 +- 0.000488 6.914634 +- 0.006568 POST: hot: 43.633557 +- 0.034373 45.333132 +- 0.002277 0.023529 +- 0.000681 cold: 207.438411 +- 0.125840 45.333132 +- 0.002277 6.976486 +- 0.004219 Averages computed over all values <128k using a LFSR to generate order. Cold numbers have a LFSR based branch trace buffer 'confuser' ran between each int_sqrt() invocation. Link: http://lkml.kernel.org/r/20171020164644.876503355@infradead.org Fixes: 30493cc9 ("lib/int_sqrt.c: optimize square root algorithm") Signed-off-by:
Anshul Garg <aksgarg1989@gmail.com> Acked-by:
Linus Torvalds <torvalds@linux-foundation.org> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Cc: Will Deacon <will.deacon@arm.com> Cc: Joe Perches <joe@perches.com> Cc: David Miller <davem@davemloft.net> Cc: Matthew Wilcox <mawilcox@microsoft.com> Cc: Kees Cook <keescook@chromium.org> Cc: Michael Davidson <md@google.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Hui Wang authored
commit b5a236c1 upstream. Recently we found the audio jack detection stop working after suspend on many machines with Realtek codec. Sometimes the audio selection dialogue didn't show up after users plugged headhphone/headset into the headset jack, sometimes after uses plugged headphone/headset, then click the sound icon on the upper-right corner of gnome-desktop, it also showed the speaker rather than the headphone. The root cause is that before suspend, the codec already call the runtime_suspend since this codec is not used by any apps, then in resume, it will not call runtime_resume for this codec. But for some realtek codec (so far, alc236, alc255 and alc891) with the specific BIOS, if it doesn't run runtime_resume after suspend, all codec functions including jack detection stop working anymore. This problem existed for a long time, but it was not exposed, that is because when problem happens, if users play sound or open sound-setting to check audio device, this will trigger calling to runtime_resume (via snd_hda_power_up), then the codec starts working again before users notice this problem. Since we don't know how many codec and BIOS combinations have this problem, to fix it, let the driver call runtime_resume for all codecs in pm_resume, maybe for some codecs, this is not needed, but it is harmless. After a codec is runtime resumed, if it is not used by any apps, it will be runtime suspended soon and furthermore we don't run suspend frequently, this change will not add much power consumption. Fixes: cc72da7d ("ALSA: hda - Use standard runtime PM for codec power-save control") Signed-off-by:
Hui Wang <hui.wang@canonical.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Takashi Iwai authored
commit 98081ca6 upstream. Currently we deal with single codec and suspend codec callbacks for all S3, S4 and runtime PM handling. But it turned out that we want distinguish the call patterns sometimes, e.g. for applying some init sequence only at probing and restoring from hibernate. This patch slightly modifies the common PM callbacks for HD-audio codec and stores the currently processed PM event in power_state of the codec's device.power field, which is currently unused. The codec callback can take a look at this event value and judges which purpose it's being called. Signed-off-by:
-
