- 17 Jan, 2013 6 commits
-
-
Felix Fietkau authored
commit 9c170e06 upstream. This reverts commit f74b9d36. Turns out reverting commit a240dc7b "ath9k_hw: Updated AR9003 tx gain table for 5GHz" was not enough to bring the tx power back to normal levels on devices like the Buffalo WZR-HP-G450H, this one needs to be reverted as well. This revert improves tx power by ~10 db on that device Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Cc: rmanohar@qca.qualcomm.com Signed-off-by:
John W. Linville <linville@tuxdriver.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Laura Abbott authored
commit c060f943 upstream. The current calculation in pfn_to_bitidx assumes that (pfn - zone->zone_start_pfn) >> pageblock_order will return the same bit for all pfn in a pageblock. If zone_start_pfn is not aligned to pageblock_nr_pages, this may not always be correct. Consider the following with pageblock order = 10, zone start 2MB: pfn | pfn - zone start | (pfn - zone start) >> page block order ---------------------------------------------------------------- 0x26000 | 0x25e00 | 0x97 0x26100 | 0x25f00 | 0x97 0x26200 | 0x26000 | 0x98 0x26300 | 0x26100 | 0x98 This means that calling {get,set}_pageblock_migratetype on a single page will not set the migratetype for the full block. Fix this by rounding down zone_start_pfn when doing the bitidx calculation. For our use case, the effects of this bug were mostly tied to the fact that CMA allocations would either take a long time or fail to happen. Depending on the driver using CMA, this could result in anything from visual glitches to application failures. Signed-off-by:
Laura Abbott <lauraa@codeaurora.org> Acked-by:
Mel Gorman <mgorman@suse.de> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Jason Liu authored
commit 7964c06d upstream. when run the folloing command under shell, it will return error sh/$ echo 1 > /proc/sys/vm/compact_memory sh/$ sh: write error: Bad address After strace, I found the following log: ... write(1, "1\n", 2) = 3 write(1, "", 4294967295) = -1 EFAULT (Bad address) write(2, "echo: write error: Bad address\n", 31echo: write error: Bad address ) = 31 This tells system return 3(COMPACT_COMPLETE) after write data to compact_memory. The fix is to make the system just return 0 instead 3(COMPACT_COMPLETE) from sysctl_compaction_handler after compaction_nodes finished. Signed-off-by:
Jason Liu <r64343@freescale.com> Suggested-by:
David Rientjes <rientjes@google.com> Acked-by:
-
Sebastian Ott authored
commit d99e79ec upstream. The check to whom a device is reserved is done by checking the path state of the affected channel paths. If it turns out that one path is flagged as reserved by someone else the whole device is marked as such. However the meaning of the RESVD_ELSE bit is that the addressed device is reserved to a different pathgroup (and not reserved to a different LPAR). If we do this test on a path which is currently not a member of the pathgroup we could erroneously mark the device as reserved to someone else. To fix this collect the reserved state for all potential members of the pathgroup and only mark the device as reserved if all of those potential members have the RESVD_ELSE bit set. Acked-by:
Peter Oberparleiter <peter.oberparleiter@de.ibm.com> Signed-off-by:
Sebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
-
Shan Hai authored
commit ce73ec6d upstream. The locking in update_vsyscall_tz() is not only unnecessary because the vdso code copies the data unproteced in __kernel_gettimeofday() but also introduces a hard to reproduce race condition between update_vsyscall() and update_vsyscall_tz(), which causes user space process to loop forever in vdso code. The following patch removes the locking from update_vsyscall_tz(). Locking is not only unnecessary because the vdso code copies the data unprotected in __kernel_gettimeofday() but also erroneous because updating the tb_update_count is not atomic and introduces a hard to reproduce race condition between update_vsyscall() and update_vsyscall_tz(), which further causes user space process to loop forever in vdso code. The below scenario describes the race condition, x==0 Boot CPU other CPU proc_P: x==0 timer interrupt update_vsyscall x==1 x++;sync settimeofday update_vsyscall_tz x==2 x++;sync x==3 sync;x++ sync;x++ proc_P: x==3 (loops until x becomes even) Because the ++ operator would be implemented as three instructions and not atomic on powerpc. A similar change was made for x86 in commit 6c260d58 ("x86: vdso: Remove bogus locking in update_vsyscall_tz") Signed-off-by:
Shan Hai <shan.hai@windriver.com> Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
-
Anton Blanchard authored
commit 11ee7e99 upstream. If we build a kernel with CONFIG_RELOCATABLE=y CONFIG_CRASH_DUMP=n, the kernel fails when we run at a non zero offset. It turns out we were incorrectly wrapping some of the relocatable kernel code with CONFIG_CRASH_DUMP. Signed-off-by:
Anton Blanchard <anton@samba.org> Signed-off-by:
-
- 11 Jan, 2013 34 commits
-
-
Greg Kroah-Hartman authored
-
Alexander Stein authored
commit ab48b03e upstream. If the restart timer is running due to BUS-OFF and the device is disconnected an dev_put will decrease the usage counter to -1 thus blocking the interface removal, resulting in the following dmesg lines repeating every 10s: can: notifier: receive list not found for dev can0 can: notifier: receive list not found for dev can0 can: notifier: receive list not found for dev can0 unregister_netdevice: waiting for can0 to become free. Usage count = -1 Signed-off-by:
Alexander Stein <alexander.stein@systec-electronic.com> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
Michal Hocko authored
commit 53a59fc6 upstream. Since commit e303297e ("mm: extended batches for generic mmu_gather") we are batching pages to be freed until either tlb_next_batch cannot allocate a new batch or we are done. This works just fine most of the time but we can get in troubles with non-preemptible kernel (CONFIG_PREEMPT_NONE or CONFIG_PREEMPT_VOLUNTARY) on large machines where too aggressive batching might lead to soft lockups during process exit path (exit_mmap) because there are no scheduling points down the free_pages_and_swap_cache path and so the freeing can take long enough to trigger the soft lockup. The lockup is harmless except when the system is setup to panic on softlockup which is not that unusual. The simplest way to work around this issue is to limit the maximum number of batches in a single mmu_gather. 10k of collected pages should be safe to prevent from soft lockups (we would have 2ms for one) even if they are all freed without an explicit scheduling point. This patch doesn't add any new explicit scheduling points because it relies on zap_pmd_range during page tables zapping which calls cond_resched per PMD. The following lockup has been reported for 3.0 kernel with a huge process (in order of hundreds gigs but I do know any more details). BUG: soft lockup - CPU#56 stuck for 22s! [kernel:31053] Modules linked in: af_packet nfs lockd fscache auth_rpcgss nfs_acl sunrpc mptctl mptbase autofs4 binfmt_misc dm_round_robin dm_multipath bonding cpufreq_conservative cpufreq_userspace cpufreq_powersave pcc_cpufreq mperf microcode fuse loop osst sg sd_mod crc_t10dif st qla2xxx scsi_transport_fc scsi_tgt netxen_nic i7core_edac iTCO_wdt joydev e1000e serio_raw pcspkr edac_core iTCO_vendor_support acpi_power_meter rtc_cmos hpwdt hpilo button container usbhid hid dm_mirror dm_region_hash dm_log linear uhci_hcd ehci_hcd usbcore usb_common scsi_dh_emc scsi_dh_alua scsi_dh_hp_sw scsi_dh_rdac scsi_dh dm_snapshot pcnet32 mii edd dm_mod raid1 ext3 mbcache jbd fan thermal processor thermal_sys hwmon cciss scsi_mod Supported: Yes CPU 56 Pid: 31053, comm: kernel Not tainted 3.0.31-0.9-default #1 HP ProLiant DL580 G7 RIP: 0010: _raw_spin_unlock_irqrestore+0x8/0x10 RSP: 0018:ffff883ec1037af0 EFLAGS: 00000206 RAX: 0000000000000e00 RBX: ffffea01a0817e28 RCX: ffff88803ffd9e80 RDX: 0000000000000200 RSI: 0000000000000206 RDI: 0000000000000206 RBP: 0000000000000002 R08: 0000000000000001 R09: ffff887ec724a400 R10: 0000000000000000 R11: dead000000200200 R12: ffffffff8144c26e R13: 0000000000000030 R14: 0000000000000297 R15: 000000000000000e FS: 00007ed834282700(0000) GS:ffff88c03f200000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: 000000000068b240 CR3: 0000003ec13c5000 CR4: 00000000000006e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Process kernel (pid: 31053, threadinfo ffff883ec1036000, task ffff883ebd5d4100) Call Trace: release_pages+0xc5/0x260 free_pages_and_swap_cache+0x9d/0xc0 tlb_flush_mmu+0x5c/0x80 tlb_finish_mmu+0xe/0x50 exit_mmap+0xbd/0x120 mmput+0x49/0x120 exit_mm+0x122/0x160 do_exit+0x17a/0x430 do_group_exit+0x3d/0xb0 get_signal_to_deliver+0x247/0x480 do_signal+0x71/0x1b0 do_notify_resume+0x98/0xb0 int_signal+0x12/0x17 DWARF2 unwinder stuck at int_signal+0x12/0x17 Signed-off-by:
Michal Hocko <mhocko@suse.cz> Cc: Mel Gorman <mgorman@suse.de> Cc: Rik van Riel <riel@redhat.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by:
-
Tony Prisk authored
commit 2f90b683 upstream. tm_mon is 0..11, whereas vt8500 expects 1..12 for the month field, causing invalid date errors for January, and causing the day field to roll over incorrectly. The century flag is only handled in vt8500_rtc_read_time, but not set in vt8500_rtc_set_time. This patch corrects the behaviour of the century flag. Signed-off-by:
Edgar Toernig <froese@gmx.de> Signed-off-by:
Tony Prisk <linux@prisktech.co.nz> Signed-off-by:
-
Tony Prisk authored
commit 532db570 upstream. Control register bitfield for 12H/24H mode is handled incorrectly. Setting CR_24H actually enables 12H mode. This patch renames the define and changes the initialization code to correctly set 24H mode. Signed-off-by:
-
Corey Minyard authored
commit c24bf9b4 upstream. The inb/outb macros for CRIS are broken from a number of points of view, missing () around parameters and they have an unprotected if statement in them. This was breaking the compile of IPMI on CRIS and thus I was being annoyed by build regressions, so I fixed them. Plus I don't think they would have worked at all, since the data values were missing "&" and the outsl had a "3" instead of a "4" for the size. From what I can tell, this stuff is not used at all, so this can't be any more broken than it was before, anyway. Signed-off-by:
Corey Minyard <cminyard@mvista.com> Cc: Jesper Nilsson <jesper.nilsson@axis.com> Cc: Mikael Starvik <starvik@axis.com> Acked-by:
Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by:
-
Gustavo Padovan authored
commit b9b5ef18 upstream. We need to cancel the hci_power_on work in order to avoid it run when we try to free the hdev. [ 1434.201149] ------------[ cut here ]------------ [ 1434.204998] WARNING: at lib/debugobjects.c:261 debug_print_object+0x8e/0xb0() [ 1434.208324] ODEBUG: free active (active state 0) object type: work_struct hint: hci _power_on+0x0/0x90 [ 1434.210386] Pid: 8564, comm: trinity-child25 Tainted: G W 3.7.0-rc5-next- 20121112-sasha-00018-g2f4ce0e #127 [ 1434.210760] Call Trace: [ 1434.210760] [<ffffffff819f3d6e>] ? debug_print_object+0x8e/0xb0 [ 1434.210760] [<ffffffff8110b887>] warn_slowpath_common+0x87/0xb0 [ 1434.210760] [<ffffffff8110b911>] warn_slowpath_fmt+0x41/0x50 [ 1434.210760] [<ffffffff819f3d6e>] debug_print_object+0x8e/0xb0 [ 1434.210760] [<ffffffff8376b750>] ? hci_dev_open+0x310/0x310 [ 1434.210760] [<ffffffff83bf94e5>] ? _raw_spin_unlock_irqrestore+0x55/0xa0 [ 1434.210760] [<ffffffff819f3ee5>] __debug_check_no_obj_freed+0xa5/0x230 [ 1434.210760] [<ffffffff83785db0>] ? bt_host_release+0x10/0x20 [ 1434.210760] [<ffffffff819f4d15>] debug_check_no_obj_freed+0x15/0x20 [ 1434.210760] [<ffffffff8125eee7>] kfree+0x227/0x330 [ 1434.210760] [<ffffffff83785db0>] bt_host_release+0x10/0x20 [ 1434.210760] [<ffffffff81e539e5>] device_release+0x65/0xc0 [ 1434.210760] [<ffffffff819d3975>] kobject_cleanup+0x145/0x190 [ 1434.210760] [<ffffffff819d39cd>] kobject_release+0xd/0x10 [ 1434.210760] [<ffffffff819d33cc>] kobject_put+0x4c/0x60 [ 1434.210760] [<ffffffff81e548b2>] put_device+0x12/0x20 [ 1434.210760] [<ffffffff8376a334>] hci_free_dev+0x24/0x30 [ 1434.210760] [<ffffffff82fd8fe1>] vhci_release+0x31/0x60 [ 1434.210760] [<ffffffff8127be12>] __fput+0x122/0x250 [ 1434.210760] [<ffffffff811cab0d>] ? rcu_user_exit+0x9d/0xd0 [ 1434.210760] [<ffffffff8127bf49>] ____fput+0x9/0x10 [ 1434.210760] [<ffffffff81133402>] task_work_run+0xb2/0xf0 [ 1434.210760] [<ffffffff8106cfa7>] do_notify_resume+0x77/0xa0 [ 1434.210760] [<ffffffff83bfb0ea>] int_signal+0x12/0x17 [ 1434.210760] ---[ end trace a6d57fefbc8a8cc7 ]--- Reported-by:
Sasha Levin <sasha.levin@oracle.com> Signed-off-by:
Gustavo Padovan <gustavo.padovan@collabora.co.uk> Signed-off-by:
-
Marcos Chaparro authored
commit acd94544 upstream. Added Atheros AR3011 internal bluetooth device found in Sony VAIO VPCEH to the devices list. Before this, the bluetooth module was identified as an Foxconn / Hai bluetooth device [0489:e027], now it claims to be an AtherosAR3011 Bluetooth [0cf3:3005]. T: Bus=01 Lev=02 Prnt=02 Port=04 Cnt=02 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e027 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by:
Marcos Chaparro <marcos@mrkindustries.com.ar> Signed-off-by:
-
Andy Lutomirski authored
commit 812089e0 upstream. Otherwise it fails like this on cards like the Transcend 16GB SDHC card: mmc0: new SDHC card at address b368 mmcblk0: mmc0:b368 SDC 15.0 GiB mmcblk0: error -110 sending status command, retrying mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb0 Tested on my Lenovo x200 laptop. [bhelgaas: changelog] Signed-off-by:
Andy Lutomirski <luto@amacapital.net> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Acked-by:
Chris Ball <cjb@laptop.org> CC: Manoj Iyer <manoj.iyer@canonical.com> Signed-off-by:
-
David Woodhouse authored
commit cae49ede upstream. We weren't clearing card->tx_skb[port] when processing the TX done interrupt. If there wasn't another skb ready to transmit immediately, this led to a double-free because we'd free it *again* next time we did have a packet to send. Signed-off-by:
David Woodhouse <David.Woodhouse@intel.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Al Viro authored
commit 7bf9b7be upstream. find_vma() is *not* safe when somebody else is removing vmas. Not just the return value might get bogus just as you are getting it (this instance doesn't try to dereference the resulting vma), the search itself can get buggered in rather spectacular ways. IOW, ->mmap_sem really, really is not optional here. Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by:
-
Will Deacon authored
commit 864aa04c upstream. When updating the page protection map after calculating the user_pgprot value, the base protection map is temporarily stored in an unsigned long type, causing truncation of the protection bits when LPAE is enabled. This effectively means that calls to mprotect() will corrupt the upper page attributes, clearing the XN bit unconditionally. This patch uses pteval_t to store the intermediate protection values, preserving the upper bits for 64-bit descriptors. Acked-by:
Nicolas Pitre <nico@linaro.org> Acked-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 354e4aa3 ] RFC 5961 5.2 [Blind Data Injection Attack].[Mitigation] All TCP stacks MAY implement the following mitigation. TCP stacks that implement this mitigation MUST add an additional input check to any incoming segment. The ACK value is considered acceptable only if it is in the range of ((SND.UNA - MAX.SND.WND) <= SEG.ACK <= SND.NXT). All incoming segments whose ACK value doesn't satisfy the above condition MUST be discarded and an ACK sent back. Move tcp_send_challenge_ack() before tcp_ack() to avoid a forward declaration. Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Neal Cardwell <ncardwell@google.com> Cc: Yuchung Cheng <ycheng@google.com> Cc: Jerry Chu <hkchu@google.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit bd090dfc ] We added support for RFC 5961 in latest kernels but TCP fails to perform exhaustive check of ACK sequence. We can update our view of peer tsval from a frame that is later discarded by tcp_ack() This makes timestamps enabled sessions vulnerable to injection of a high tsval : peers start an ACK storm, since the victim sends a dupack each time it receives an ACK from the other peer. As tcp_validate_incoming() is called before tcp_ack(), we should not peform tcp_replace_ts_recent() from it, and let callers do it at the right time. Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit e3715899 ] Followup of commit 0c24604b (tcp: implement RFC 5961 4.2) As reported by Vijay Subramanian, we should send a challenge ACK instead of a dup ack if a SYN flag is set on a packet received out of window. This permits the ratelimiting to work as intended, and to increase correct SNMP counters. Suggested-by:
Vijay Subramanian <subramanian.vijay@gmail.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 0c24604b ] Implement the RFC 5691 mitigation against Blind Reset attack using SYN bit. Section 4.2 of RFC 5961 advises to send a Challenge ACK and drop incoming packet, instead of resetting the session. Add a new SNMP counter to count number of challenge acks sent in response to SYN packets. (netstat -s | grep TCPSYNChallenge) Remove obsolete TCPAbortOnSyn, since we no longer abort a TCP session because of a SYN flag. Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 282f23c6 ] Implement the RFC 5691 mitigation against Blind Reset attack using RST bit. Idea is to validate incoming RST sequence, to match RCV.NXT value, instead of previouly accepted window : (RCV.NXT <= SEG.SEQ < RCV.NXT+RCV.WND) If sequence is in window but not an exact match, send a "challenge ACK", so that the other part can resend an RST with the appropriate sequence. Add a new sysctl, tcp_challenge_ack_limit, to limit number of challenge ACK sent per second. Add a new SNMP counter to count number of challenge acks sent. (netstat -s | grep TCPChallengeACK) Signed-off-by:
-
Stefan Hasko authored
[ Upstream commit d2fe85da ] Fixed integer overflow in function htb_dequeue Signed-off-by:
Stefan Hasko <hasko.stevo@gmail.com> Acked-by:
-
Dave Kleikamp authored
[ Upstream commit 6cb9c369 ] Modifying the huge pte's requires that all the underlying pte's be modified. Version 2: added missing flush_tlb_page() Signed-off-by:
Dave Kleikamp <dave.kleikamp@oracle.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: sparclinux@vger.kernel.org Signed-off-by:
-
Steven Rostedt authored
commit 45959ee7 upstream. When gcc inlines a function, it does not mark it with the mcount prologue, which in turn means that inlined functions are not traced by the function tracer. But if CONFIG_OPTIMIZE_INLINING is set, then gcc is allowed not to inline a function that is marked inline. Depending on the options and the compiler, a function may or may not be traced by the function tracer, depending on whether gcc decides to inline a function or not. This has caused several problems in the pass becaues gcc is not always consistent with what it decides to inline between different gcc versions. Some places should not be traced (like paravirt native_* functions) and these are mostly marked as inline. When gcc decides not to inline the function, and if that function should not be traced, then the ftrace function tracer will suddenly break when it use to work fine. This becomes even harder to debug when different versions of gcc will not inline that function, making the same kernel and config work for some gcc versions and not work for others. By making all functions marked inline to not be traced will remove the ambiguity that gcc adds when it comes to tracing functions marked inline. All gcc versions will be consistent with what functions are traced and having volatile working code will be removed. Note, only the inline macro when CONFIG_OPTIMIZE_INLINING is set needs to have notrace added, as the attribute __always_inline will force the function to be inlined and then not traced. Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Andre Przywara authored
commit 2bbf0a14 upstream. The Way Access Filter in recent AMD CPUs may hurt the performance of some workloads, caused by aliasing issues in the L1 cache. This patch disables it on the affected CPUs. The issue is similar to that one of last year: http://lkml.indiana.edu/hypermail/linux/kernel/1107.3/00041.html This new patch does not replace the old one, we just need another quirk for newer CPUs. The performance penalty without the patch depends on the circumstances, but is a bit less than the last year's 3%. The workloads affected would be those that access code from the same physical page under different virtual addresses, so different processes using the same libraries with ASLR or multiple instances of PIE-binaries. The code needs to be accessed simultaneously from both cores of the same compute unit. More details can be found here: http://developer.amd.com/Assets/SharedL1InstructionCacheonAMD15hCPU.pdf CPUs affected are anything with the core known as Piledriver. That includes the new parts of the AMD A-Series (aka Trinity) and the just released new CPUs of the FX-Series (aka Vishera). The model numbering is a bit odd here: FX CPUs have model 2, A-Series has model 10h, with possible extensions to 1Fh. Hence the range of model ids. Signed-off-by:
Andre Przywara <osp@andrep.de> Link: http://lkml.kernel.org/r/1351700450-9277-1-git-send-email-osp@andrep.deSigned-off-by:
H. Peter Anvin <hpa@linux.intel.com> Signed-off-by:
CAI Qian <caiqian@redhat.com> Signed-off-by:
-
Tejun Heo authored
commit 17543163 upstream. cgroup_create_dir() does weird dancing with dentry refcnt. On success, it gets and then puts it achieving nothing. On failure, it puts but there isn't no matching get anywhere leading to the following oops if cgroup_create_file() fails for whatever reason. ------------[ cut here ]------------ kernel BUG at /work/os/work/fs/dcache.c:552! invalid opcode: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC Modules linked in: CPU 2 Pid: 697, comm: mkdir Not tainted 3.7.0-rc4-work+ #3 Bochs Bochs RIP: 0010:[<ffffffff811d9c0c>] [<ffffffff811d9c0c>] dput+0x1dc/0x1e0 RSP: 0018:ffff88001a3ebef8 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffff88000e5b1ef8 RCX: 0000000000000403 RDX: 0000000000000303 RSI: 2000000000000000 RDI: ffff88000e5b1f58 RBP: ffff88001a3ebf18 R08: ffffffff82c76960 R09: 0000000000000001 R10: ffff880015022080 R11: ffd9bed70f48a041 R12: 00000000ffffffea R13: 0000000000000001 R14: ffff88000e5b1f58 R15: 00007fff57656d60 FS: 00007ff05fcb3800(0000) GS:ffff88001fd00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00000000004046f0 CR3: 000000001315f000 CR4: 00000000000006e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Process mkdir (pid: 697, threadinfo ffff88001a3ea000, task ffff880015022080) Stack: ffff88001a3ebf48 00000000ffffffea 0000000000000001 0000000000000000 ffff88001a3ebf38 ffffffff811cc889 0000000000000001 ffff88000e5b1ef8 ffff88001a3ebf68 ffffffff811d1fc9 ffff8800198d7f18 ffff880019106ef8 Call Trace: [<ffffffff811cc889>] done_path_create+0x19/0x50 [<ffffffff811d1fc9>] sys_mkdirat+0x59/0x80 [<ffffffff811d2009>] sys_mkdir+0x19/0x20 [<ffffffff81be1e02>] system_call_fastpath+0x16/0x1b Code: 00 48 8d 90 18 01 00 00 48 89 93 c0 00 00 00 4c 89 a0 18 01 00 00 48 8b 83 a0 00 00 00 83 80 28 01 00 00 01 e8 e6 6f a0 00 eb 92 <0f> 0b 66 90 0f 1f 44 00 00 55 48 89 e5 41 57 41 56 49 89 fe 41 RIP [<ffffffff811d9c0c>] dput+0x1dc/0x1e0 RSP <ffff88001a3ebef8> ---[ end trace 1277bcfd9561ddb0 ]--- Fix it by dropping the unnecessary dget/dput() pair. Signed-off-by:
Tejun Heo <tj@kernel.org> Acked-by:
Li Zefan <lizefan@huawei.com> Signed-off-by:
-
Russell Webb authored
commit bb1e5dd7 upstream. Like Lynx Point, Lynx Point LP is also switchable. See 1c12443a for more details. This patch should be backported to stable kernels as old as 3.0, that contain commit 69e848c2 "Intel xhci: Support EHCI/xHCI port switching." Signed-off-by:
Russell Webb <russell.webb@linux.intel.com> Signed-off-by:
Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by:
-
Thomas Gleixner authored
commit 04aa530e upstream. Sankara reported that the genirq core code fails to adjust the affinity of an interrupt thread in several cases: 1) On request/setup_irq() the call to setup_affinity() happens before the new action is registered, so the new thread is not notified. 2) For secondary shared interrupts nothing notifies the new thread to change its affinity. 3) Interrupts which have the IRQ_NO_BALANCE flag set are not moving the thread either. Fix this by setting the thread affinity flag right on thread creation time. This ensures that under all circumstances the thread moves to the right place. Requires a check in irq_thread_check_affinity for an existing affinity mask (CONFIG_CPU_MASK_OFFSTACK=y) Reported-and-tested-by:
Sankara Muthukrishnan <sankara.m@gmail.com> Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1209041738200.2754@ionosSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Peter Popovec authored
commit a455e298 upstream. The driver's timer must be set up before enabling IRQ handler, otherwise bad things may happen. Reported-and-tested-by:
Fengguang Wu <fengguang.wu@intel.com> Signed-off-by:
Peter Popovec <popovec@fei.tuke.sk> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Xi Wang authored
commit e25fbe38 upstream. The following null pointer check is broken. *option = match_strdup(args); return !option; The pointer `option' must be non-null, and thus `!option' is always false. Use `!*option' instead. The bug was introduced in commit c5cb09b6 ("Cleanup: Factor out some cut-and-paste code."). Signed-off-by:
Xi Wang <xi.wang@gmail.com> Signed-off-by:
Trond Myklebust <Trond.Myklebust@netapp.com> Signed-off-by:
-
J. Bruce Fields authored
commit d5f50b0c upstream. If the argument and reply together exceed the maximum payload size, then a reply with a read-like operation can overlow the rq_pages array. Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
-
Trond Myklebust authored
commit 1f018458 upstream. It is almost always wrong for NFS to call drop_nlink() after removing a file. What we really want is to mark the inode's attributes for revalidation, and we want to ensure that the VFS drops it if we're reasonably sure that this is the final unlink(). Do the former using the usual cache validity flags, and the latter by testing if inode->i_nlink == 1, and clearing it in that case. This also fixes the following warning reported by Neil Brown and Jeff Layton (among others). [634155.004438] WARNING: at /home/abuild/rpmbuild/BUILD/kernel-desktop-3.5.0/lin [634155.004442] Hardware name: Latitude E6510 [634155.004577] crc_itu_t crc32c_intel snd_hwdep snd_pcm snd_timer snd soundcor [634155.004609] Pid: 13402, comm: bash Tainted: G W 3.5.0-36-desktop # [634155.004611] Call Trace: [634155.004630] [<ffffffff8100444a>] dump_trace+0xaa/0x2b0 [634155.004641] [<ffffffff815a23dc>] dump_stack+0x69/0x6f [634155.004653] [<ffffffff81041a0b>] warn_slowpath_common+0x7b/0xc0 [634155.004662] [<ffffffff811832e4>] drop_nlink+0x34/0x40 [634155.004687] [<ffffffffa05bb6c3>] nfs_dentry_iput+0x33/0x70 [nfs] [634155.004714] [<ffffffff8118049e>] dput+0x12e/0x230 [634155.004726] [<ffffffff8116b230>] __fput+0x170/0x230 [634155.004735] [<ffffffff81167c0f>] filp_close+0x5f/0x90 [634155.004743] [<ffffffff81167cd7>] sys_close+0x97/0x100 [634155.004754] [<ffffffff815c3b39>] system_call_fastpath+0x16/0x1b [634155.004767] [<00007f2a73a0d110>] 0x7f2a73a0d10f Signed-off-by:
-
NeilBrown authored
commit f259613a upstream. In rare circumstances, nfs_clone_server() of a v2 or v3 server can get an error between setting server->destory (to nfs_destroy_server), and calling nfs_start_lockd (which will set server->nlm_host). If this happens, nfs_clone_server will call nfs_free_server which will call nfs_destroy_server and thence nlmclnt_done(NULL). This causes the NULL to be dereferenced. So add a guard to only call nlmclnt_done() if ->nlm_host is not NULL. The other guards there are irrelevant as nlm_host can only be non-NULL if one of these flags are set - so remove those tests. (Thanks to Trond for this suggestion). This is suitable for any stable kernel since 2.6.25. Signed-off-by:
NeilBrown <neilb@suse.de> Signed-off-by:
-
Rafael J. Wysocki authored
commit 4f5f64cf upstream. At one point acpi_device_set_id() checks if acpi_device_hid(device) returns NULL, but that never happens, so system bus devices with an empty list of PNP IDs are given the dummy HID ("device") instead of the "system bus HID" ("LNXSYBUS"). Fix the code to use the right check. Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Sebastian Andrzej Siewior authored
commit d0eca719 upstream. Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
-
Christian Lamparter authored
commit 4010fe21 upstream. This patch adds USBIDs for: - DrayTek Vigor 530 - Zoom 4410a It also adds a note about Gemtek WUBI-100GW and SparkLAN WL-682 USBID conflict [WUBI-100GW is a ISL3886+NET2280 (LM86 firmare) solution, whereas WL-682 is a ISL3887 (LM87 firmware)] device. Source: <http://www.wikidevi.com/wiki/Intersil/p54/usb/windows> Signed-off-by:
Christian Lamparter <chunkeey@googlemail.com> Signed-off-by:
-
Tomasz Guszkowski authored
commit 3194b7fc upstream. Added USB ID for T-Com Sinus 154 data II. Signed-off-by:
Tomasz Guszkowski <tsg@o2.pl> Acked-by:
-
Takashi Iwai authored
commit f5f16541 upstream. The commit [88a8516a: ALSA: usbaudio: implement USB autosuspend] added the support of autopm for USB MIDI output, but it didn't take the MIDI input into account. This patch adds the following for fixing the autopm: - Manage the URB start at the first MIDI input stream open, instead of the time of instance creation - Move autopm code to the common substream_open() - Make snd_usbmidi_input_start/_stop() more robust and add the running state check Reviewd-by:
Clemens Ladisch <clemens@ladisch.de> Tested-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
