Use devm_ioremap_resource to simplify error handling in the probe
function and to get rid of some boilerplate in the remove function.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Adds chipidea to the list of DT vendor prefixes.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some kernel-doc style comment are not satisfied for format, fix them.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We have only needed to enable otg initialization when both of
below conditions are satisfied:

- The controller is otg capable
- The gadget function is enabled

If the controller is otg capable, but is host-only configuration, we do
not need to access register otgsc and do any otg operations (eg, create
otg workqueue).
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds Vybrid VF610 SoC support. The IP is very similar to i.MX6,
however, the non-core registers are spread in two different register
areas. Hence we support multiple instances of the USB misc driver
and add the driver instance to the imx_usbmisc_data structure.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

TPL (Targeted Peripheral List) is needed for targets host
(OTG and Embedded Hosts) for usb certification and other
vendor specific requirements.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

For OTG and Embedded hosts, they may need TPL (Targeted Peripheral List)
for usb certification and other vender specific requirements, the
platform can tell chipidea core driver if it supports tpl through DT
or platform data.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The TPL (Targeted Peripheral List) is used for targeted hosts
(non-PC hosts), and it can be used at USB OTG & EH certification
and some specific products which need white list.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Update configuration for USB_OTG_WHITELIST, any targeted hosts
(non PC-hosts) can have TPL (Targered Peripheral List).
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

According to On-The-Go and Embedded Host Supplement to the USB Revision
2.0 Specification, the targeted hosts (non-PC hosts) include both
embedded hosts and otg, and each targeted host product defines the
set of supported peripherals on a TPL (Targeted Peripheral List). So,
TPL should apply for both OTG and embedded host, and the otg support is
not a must for embedded host.

The TPL support feature will only be effect when CONFIG_USB_OTG_WHITELIST
has been chosen and hcd->tpl_support flag is set, it can avoid the enumeration
fails problem for the user who chooses CONFIG_USB_OTG_WHITELIST wrongly.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The targeted hosts (non-PC hosts) need to have TPL (Targeted Peripheral List)
for USB OTG & EH certification and other vendor specific requirements.

The platform who needs TPL feature should set this flag at usb host
controller driver.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Enable device-qualifier quirk for Elan Touchscreen, which often fails to
handle requests for the device_descriptor.

Note that the device sometimes do respond properly with a Request Error
(three times as USB core retries), but usually fails to respond at all.
When this happens any further descriptor requests also fails, for
example:

[ 1528.688934] usb 2-7: new full-speed USB device number 4 using xhci_hcd
[ 1530.945588] usb 2-7: unable to read config index 0 descriptor/start: -71
[ 1530.945592] usb 2-7: can't read configurations, error -71

This has been observed repeating for over a minute before eventual
successful enumeration.
Reported-by: Drew Von Spreecken <drewvs@gmail.com>
Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add new quirk for devices that cannot handle requests for the
device_qualifier descriptor.

A USB-2.0 compliant device must respond to requests for the
device_qualifier descriptor (even if it's with a request error), but at
least one device is known to misbehave after such a request.
Suggested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit f2267089.

That commit causes more problem than fixes. Firstly, kfree()
should be called after usb_ep_dequeue() and secondly, the way
things are, we will try to dequeue a request that has already
completed much more frequently than one which is pending.

Cc: Li Jun <b47624@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Cc: stable <stable@vger.kernel.org> # 3.17
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We want the USB fixes in this branch as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'usb-serial-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next

Johan writes:

USB-serial updates for v3.18-rc1

These changes add two new "simple" drivers, while removing the redundant
zte_ev driver (PIDs moved to option).

Included are also some minor clean ups to the xsens_mt driver, and the
enabling of further baud rates for pl2303 devices.
Signed-off-by: Johan Hovold <johan@kernel.org>

Pull ARM fixes from Russell King:
 "Fixes for ARM, the most notable being the fix from Nathan Lynch to fix
  the state of various registers during execve, to ensure that data
  can't be leaked between two executables.

  Fixes from Victor Kamensky for get_user() on big endian platforms,
  since the addition of 8-byte get_user() support broke these fairly
  badly.

  A fix from Sudeep Holla for affinity setting when hotplugging CPU 0.

  A fix from Stephen Boyd for a perf-induced sleep attempt while atomic.

  Lastly, a correctness fix for emulation of the SWP instruction on
  ARMv7+, and a fix for wrong carry handling when updating the
  translation table base address on LPAE platforms"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 8149/1: perf: Don't sleep while atomic when enabling per-cpu interrupts
  ARM: 8148/1: flush TLS and thumbee register state during exec
  ARM: 8151/1: add missing exports for asm functions required by get_user macro
  ARM: 8137/1: fix get_user BE behavior for target variable with size of 8 bytes
  ARM: 8135/1: Fix in-correct barrier usage in SWP{B} emulation
  ARM: 8133/1: use irq_set_affinity with force=false when migrating irqs
  ARM: 8132/1: LPAE: drop wrong carry flag correction after adding TTBR1_OFFSET

Pull media fixes from Mauro Carvalho Chehab:
 "some media bug fixes:
   - a Kconfig dependency issue
   - some fixes for af9033/it913x demod to be more reliable and address
     a performance regression
   - cx18: fix an oops on devices with tda8290 tuner
   - two new USB IDs for af9035
   - a couple fixes on smapp driver"

* tag 'media-v3.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  [media] af9035: new IDs: add support for PCTV 78e and PCTV 79e
  [media] af9033: feed clock to RF tuner
  [media] it913x: init tuner on attach
  [media] af9033: update IT9135 tuner inittabs
  [media] Kconfig: do not select SPI bus on sub-driver auto-select
  [media] cx18: fix kernel oops with tda8290 tuner
  [media] smiapp: Set sub-device owner
  [media] smiapp: Fix power count handling

Pull staging / IIO fixes from Greg KH:
 "Here are some IIO and Staging driver fixes for 3.17-rc6.  They are all
  pretty simple, and resolve reported issues"

* tag 'staging-3.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: vt6655: buffer overflow in ioctl
  iio:magnetometer: bugfix magnetometers gain values
  iio: adc: at91: don't use the last converted data register
  iio: adc: xilinx-xadc: assign auxiliary channels address correctly
  iio: meter: ade7758: Fix indio_dev->trig assignment
  iio: inv_mpu6050: Fix indio_dev->trig assignment
  iio: gyro: itg3200: Fix indio_dev->trig assignment
  iio: st_sensors: Fix indio_dev->trig assignment
  iio: hid_sensor_hub: Fix indio_dev->trig assignment
  iio: adc: ad_sigma_delta: Fix indio_dev->trig assignment
  iio: accel: bma180: Fix indio_dev->trig assignment
  iio:trigger: modify return value for iio_trigger_get
  iio:inkern: fix overwritten -EPROBE_DEFER in of_iio_channel_get_by_name

Pull USB fixes / quirks from Greg KH:
 "Here are some USB and PHY fixes and quirks for 3.17-rc6.  Nothing
  major, just a few things that have been reported"

* tag 'usb-3.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: storage: Add quirks for Entrega/Xircom USB to SCSI converters
  USB: storage: Add quirk for Ariston Technologies iConnect USB to SCSI adapter
  USB: storage: Add quirk for Adaptec USBConnect 2000 USB-to-SCSI Adapter
  USB: EHCI: unlink QHs even after the controller has stopped
  phy: spear1340-miphy: fix driver dependencies
  phy: spear1310-miphy: fix driver dependencies
  phy: miphy365x: Fix off-by-one error

Pull SCSI target fixes from Nicholas Bellinger:
 "Here are the target pending fixes for v3.17-rc6.

  Included are Sagi's long overdue fixes related to iser-target
  shutdown, along with a couple of fixes from Sebastian related to ALUA
  Referrals changes that when in during the v3.14 time-frame.

  Also included are a few iscsi-target fixes, most recently of which
  where found during Joern's Coverity scanning of target code"

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  iscsi-target: avoid NULL pointer in iscsi_copy_param_list failure
  iscsi-target: Fix memory corruption in iscsit_logout_post_handler_diffcid
  target: Fix inverted logic in SE_DEV_ALUA_SUPPORT_STATE_STORE
  target: Fix user data segment multiplier in spc_emulate_evpd_b3()
  iscsi-target: Ignore ICF_GOT_LAST_DATAOUT during Data-Out ITT lookup
  Target/iser: Fix initiator_depth and responder_resources
  Target/iser: Avoid calling rdma_disconnect twice
  Target/iser: Don't put isert_conn inside disconnected handler
  Target/iser: Get isert_conn reference once got to connected_handler

Pull drm fixes from Dave Airlie:
 "A bunch of radeon fixes for oops on module unload, and problems with
  resetting the dma engine, one nouveau fix for black boxes in rendering
  on my mbp retina, one sti fix, and a couple of intel fixes"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/nouveau: ltc/gf100-: fix cbc issues on certain boards
  drm/bochs: add missing drm_connector_register call
  drm/cirrus: add missing drm_connector_register call
  drm/radeon: Fix typo 'addr' -> 'entry' in rs400_gart_set_page
  drm/nouveau/runpm: fix module unload
  drm/radeon/px: fix module unload
  vgaswitcheroo: add vga_switcheroo_fini_domain_pm_ops
  drm/radeon: don't reset dma on r6xx-evergreen init
  drm/radeon: don't reset sdma on CIK init
  drm/radeon: don't reset dma on NI/SI init
  drm/radeon/dpm: fix resume on mullins
  drm/radeon: Disable HDP flush before every CS again for < r600
  drm/radeon: delete unused PTE_* defines
  drm/i915: Add limited color range readout for HDMI/DP ports on g4x/vlv/chv
  drm: sti: do not iterate over the info frame array
  drm/i915: Fix SRC_COPY width on 830/845g

A mismatch between FB and LTC's idea of how big a large page is causes
issues such as black "holes" in rendering to occur on some boards
(those where LTC is configured for 64KiB large pages) when compression
is used.

Confirmed to fix at least the GK107 MBP.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>

single fix for regression on rs4xx/rs690/rs740
* 'drm-fixes-3.17' of git://people.freedesktop.org/~agd5f/linux:
  drm/radeon: Fix typo 'addr' -> 'entry' in rs400_gart_set_page

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Starting with v3.18-rc, patches for dwc2 will go through Felipe's
tree. Add a T: line to MAINTAINERS to document this.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The driver's handling of DMA buffers for non-aligned transfers
was kind of nuts. For IN transfers, it left the URB DMA buffer
mapped until the transfer completed, then synced it, copied the
data from the bounce buffer, then synced it again.

Instead of that, just call usb_hcd_unmap_urb_for_dma() to unmap
the buffer before starting the transfer. Then no syncing is
required when doing the copy. This should also allow handling of
other types of mappings besides just dma_map_single() ones.

Also reduce the size of the bounce buffer allocation for Isoc
endpoints to 3K, since that's the largest possible transfer size.

Tested on Raspberry Pi and Altera SOCFPGA.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Clip max_transfer_size to 65535 for host. dwc2_hc_setup_align_buf()
allocates coherent buffers with this size, and if it's too large we
can exhaust the coherent DMA pool.

Tested on Raspberry Pi and Altera SOCFPGA.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When device is stopped or suspended clock is not needed so we
can disable it for this time.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Because we have not enough memory to have each TX FIFO of size at least
3072 bytes (the maximum single packet size with 3 transactions per
microframe), we create four FIFOs of lenght 1024, and four of length
3072 bytes, and assing them to endpoints dynamically according to
maxpacket size value of given endpoint.

Up to now there were initialized 16 TX FIFOs, but we use only 8 IN
endpoints, so we can split available memory for 8 FIFOs to have more
memory for each one.

It needed to do some small modifications in few places in code, because
there was assumption that TX FIFO numbers assigned to endpoints are the
same as the endpoint numbers, which is not true since we have dynamic
FIFO assigning.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Print warning if FIFOs are configured in such a way that they don't fit
into the SPRAM available on the s3c hsotg module.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some DWC2/s3c-hsotg debug messages are really useless for typical user,
so hide them behind dev_dbg().
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Adjust the debug text to the name of the printed variable.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

->u.generic_elem.len is a user controlled number between 0-255.  We
should limit it to avoid memory corruption.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'iio-fixes-3.17a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus

Jonathan writes:

First round of IIO fixes for the 3.17 cycle.

* Fix an overwritten error return that can prevent deferred probing when
  using of_iio_channel_get_by_name
* A series that deals with an incorrect reference count when the default
  trigger is set within the main probe routine for a driver.  Can result
  in a double free if the trigger is changed.
* Fix a buglet with xilinx-xadc concerning setup of the address for an
  aux channel.
* At91 adc driver could sometimes get a touchscreen reading rather than
  the intended adc channel.  This is fixed by using the channel data register
  instead.
* Fix some ST magnetometer gain values that differ in production parts from
  the prerelease ones used for driver development.

Felipe writes:

usb: changes for v3.18 merge window

Quite big pull request this time. Audio and UVC gadgets
can now be used with our configfs-based binding. We have
three PHY drivers being removed because a new one has been
added using new PHY framework.

Gadget framework got a new ->reset callback preparing for
some other changes to come on next merge window.

A few new drivers came in as well; among those we have a
new UDC driver from Xilinx and two new glue layers for
DWC3 (ST and Qualcomm).

DWC3 also learned about tracepoints which will help debugging
quite a bit.

Other than that, a big series of non-critical fixes and
cleanups.

All patches have been on linux-next for quite a bit of time
and I boot tested these changes on platforms I have access
to and work with mainline.
Signed-of-by: Felipe Balbi <balbi@ti.com>

This patch adds quirks for Entrega Technologies (later Xircom PortGear) USB-
SCSI converters. They use Shuttle Technology EUSB-01/EUSB-S1 chips. The
US_FL_SCM_MULT_TARG quirk is needed to allow multiple devices on the SCSI
chain to be accessed. Without it only the (single) device with SCSI ID 0
can be used.

The standalone converter sold by Entrega had model number U1-SC25. Xircom
acquired Entrega and re-branded the product line PortGear. The PortGear USB
to SCSI Converter (model PGSCSI) is internally identical to the Entrega
product, but later models may use a different USB ID. The Entrega-branded
units have USB ID 1645:0007, as does my Xircom PGSCSI, but the Windows and
Macintosh drivers also support 085A:0028.

Entrega also sold the "Mac USB Dock", which provides two USB ports, a Mac
(8-pin mini-DIN) serial port and a SCSI port. It appears to the computer as
a four-port hub, USB-serial, and USB-SCSI converters. The USB-SCSI part may
have initially used the same ID as the standalone U1-SC25 (1645:0007), but
later production used 085A:0026.

My Xircom PortGear PGSCSI has bcdDevice=0x0100. Units with bcdDevice=0x0133
probably also exist.

This patch adds quirks for 1645:0007, 085A:0026 and 085A:0028. The Windows
driver INF file also mentions 085A:0032 "PortStation SCSI Module", but I
couldn't find any mention of that actually existing in the wild; perhaps it
was cancelled before release?
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Hi,

The Ariston Technologies iConnect 025 and iConnect 050 (also known as e.g.
iSCSI-50) are SCSI-USB converters which use Shuttle Technology/SCM
Microsystems chips. Only the connectors differ; both have the same USB ID.
The US_FL_SCM_MULT_TARG quirk is required to use SCSI devices with ID other
than 0.

I don't have one of these, but based on the other entries for Shuttle/
SCM-based converters this patch is very likely correct. I used 0x0000 and
0x9999 for bcdDeviceMin and bcdDeviceMax because I'm not sure which
bcdDevice value the products use.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>