Since 25aaa75d SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX6QDL_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality(this at least
breaks RAVE SP serdev driver on RDU2). Fix the code to specify
IMX6QDL_CLK_IPG as "ipg" clock for SDMA, to avoid detecting incorrect
clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Warp7 comes with a Omnivision OV2680 sensor, add the node here to make
complete the camera data path for this system. Add the needed regulator
to the analog voltage supply, the port and endpoints in mipi_csi node
and the pinctrl for the reset gpio.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add and enable csi and mipi_csi nodes.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add device tree nodes for csi, video multiplexer and mipi-csi.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The IOMUXC General Purpose Register has bitfield to control video bus
multiplexer to control the CSI input between the MIPI-CSI2 and parallel
interface. Add that register and mask.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add power domain index 0 related with mipi-phy to imx7s.

While at it rename pcie power-domain node to remove pgc prefix.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This adds support for the TQ TQMa7D SoM together with
the MBa7 carrier board and it's based on the NXP i.MX7Dual SoC.
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This adds support for the TQ TQMa7S SoM together with
the MBa7 carrier board and it's based on the NXP i.MX7Solo SoC.
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This adds TQMa7 and MBa7 board support.
TQMa7 can be mounted with either i.MX7 Solo or Dual.
All TQMa7 board variants can be mounted in MBa7 carrier board.
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX6 comes with 4 viewports, so configure PCIE node accordingly so
that the driver won't assume we only have 2.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX7D comes with 4 viewports, so configure PCIE node accordingly so
that the driver won't assume we only have 2.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Only a certain number of CFU1's come with NOR flash populated. Disable
it by default to avoid trying to probe NOR flash on devices that don't
have it. Devices that do have it can rely on the bootloader to enable
this node.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add Device Tree for VF610 based Zodiac Seat Power Box.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-imx@nxp.com
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add i.MX7ULP OCOTP support, its clock source is from
M4 BUS clock which is NOT available in Linux clock tree,
but M4 BUS clock is always ON when A7 (Linux) is alive,
so just use dummy clock here.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This is one of two boards that make use of the recently introduced SIOX
bus. Apart from the devices described in the dts it features a display
with touch that I didn't include here because it needs some non-mainline
change to operate correctly.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

After switching to the new FSL QSPI driver the properties
'fsl,qspi-has-second-chip' and 'big-endian' are not used anymore.

The driver now uses the 'reg' property to determine the bus and
the chipselect. The endianness is selected by the driver depending
on which SoC is used.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Even though the ChipIdea USB controller binding[1] doesn't specify the
properties that reference a PHY as required, the Linux driver
requires[2] such a reference.

The clock situation is like on i.MX53: The USB controller is clocked
from IMX5_CLK_USBOH3_GATE and the PHY from IMX5_CLK_USB_PHY1_GATE.

[1]: Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt
[2]: Search for EINVAL in drivers/usb/chipidea/ci_hdrc_imx.c
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Using aliases, the devices will be enumerated properly.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Using aliases, the devices will be enumerated properly.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Using aliases, the devices will be enumerated properly.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The 'max-brightness' property is not a valid one as per
Documentation/devicetree/bindings/leds/leds-gpio.txt, so remove it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add MMDC1 compatible string which is missing, and also set
it to be disabled by default, as most of the platforms ONLY
use single channel MMDC0, if dual MMDC channels are used, it
can be enabled in board dts file.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Node name should be generic, so use "memory-controller"
instead of "mmdc" for MMDC node name, also remove "mmdc"
label for platforms with single MMDC node.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX7ULP has a MMDC module to control DDR, it reuses
i.MX6Q's MMDC module, add support for it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The imx6q Technical reference manual shows the interrupt is
available to wake from sleep using the power button. The driver
has been available for quite some time, and other variants of the
i.MX6 have it enabled, so this implements it much like the others.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Now that the backlight driver is upstream, we can properly manage the
backlight from the panel.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This adds the i2c device node for the ethernet switch watchdog.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

PMIC swbst regulator is used for the MikroBUS socket (pin +5V).

We have to set the regulator to "boot-on" and "always-on"
to output a voltage of 5V on this socket.
Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch is to enable esdhc controller in ls1021aqds
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The GW54xx has a front-panel microHDMI connector routed to a TDA19971
which is connected the the IPU CSI when using IMX6Q.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The GW551x has a front-panel microHDMI connector routed to a TDA19971
which is connected the the IPU CSI.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

On vf610-zii-ssmb-spu3 board there is a supervisory microcontroller that
provides the watchdog functionality, so disable the on-chip Vybrid's
watchdog.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

None of these vf610-zii boards have a battery or super-capacitor
holding up power to the SNVS RTC embedded in the Vybrid SoC,
so it is preferable to disable the snvsrtc node.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Partitions in the NOR and EEPROM are application specific. Prepare the
SoM device tree so platform device tree's can add partitions.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Pull more Kbuild updates from Masahiro Yamada:

 - add more Build-Depends to Debian source package

 - prefix header search paths with $(srctree)/

 - make modpost show verbose section mismatch warnings

 - avoid hard-coded CROSS_COMPILE for h8300

 - fix regression for Debian make-kpkg command

 - add semantic patch to detect missing put_device()

 - fix some warnings of 'make deb-pkg'

 - optimize NOSTDINC_FLAGS evaluation

 - add warnings about redundant generic-y

 - clean up Makefiles and scripts

* tag 'kbuild-v5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kconfig: remove stale lxdialog/.gitignore
  kbuild: force all architectures except um to include mandatory-y
  kbuild: warn redundant generic-y
  Revert "modsign: Abort modules_install when signing fails"
  kbuild: Make NOSTDINC_FLAGS a simply expanded variable
  kbuild: deb-pkg: avoid implicit effects
  coccinelle: semantic code search for missing put_device()
  kbuild: pkg: grep include/config/auto.conf instead of $KCONFIG_CONFIG
  kbuild: deb-pkg: introduce is_enabled and if_enabled_echo to builddeb
  kbuild: deb-pkg: add CONFIG_ prefix to kernel config options
  kbuild: add workaround for Debian make-kpkg
  kbuild: source include/config/auto.conf instead of ${KCONFIG_CONFIG}
  unicore32: simplify linker script generation for decompressor
  h8300: use cc-cross-prefix instead of hardcoding h8300-unknown-linux-
  kbuild: move archive command to scripts/Makefile.lib
  modpost: always show verbose warning for section mismatch
  ia64: prefix header search path with $(srctree)/
  libfdt: prefix header search paths with $(srctree)/
  deb-pkg: generate correct build dependencies

Pull x86 asm updates from Thomas Gleixner:
 "Two cleanup patches removing dead conditionals and unused code"

* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/asm: Remove unused __constant_c_x_memset() macro and inlines
  x86/asm: Remove dead __GNUC__ conditionals

Pull perf fixes from Thomas Gleixner:
 "Three fixes for the fallout from the TSX errata workaround:

   - Prevent memory corruption caused by a unchecked out of bound array
     index.

   - Two trivial fixes to address compiler warnings"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/intel: Make dev_attr_allow_tsx_force_abort static
  perf/x86: Fixup typo in stub functions
  perf/x86/intel: Fix memory corruption

Pull xen fix from Juergen Gross:
 "A fix for a Xen bug introduced by David's series for excluding
  ballooned pages in vmcores"

* tag 'for-linus-5.1b-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/balloon: Fix mapping PG_offline pages to user space

Pull 9p updates from Dominique Martinet:
 "Here is a 9p update for 5.1; there honestly hasn't been much.

  Two fixes (leak on invalid mount argument and possible deadlock on
  i_size update on 32bit smp) and a fall-through warning cleanup"

* tag '9p-for-5.1' of git://github.com/martinetd/linux:
  9p/net: fix memory leak in p9_client_create
  9p: use inode->i_lock to protect i_size_write() under 32-bit
  9p: mark expected switch fall-through