This fixes the build of the macb driver that was broken by the DT changes:

drivers/net/ethernet/cadence/macb.c:1503: error: implicit declaration of function 'of_match_ptr'
drivers/net/ethernet/cadence/macb.c:1503: error: 'macb_dt_ids' undeclared here (not in a function)
drivers/net/ethernet/cadence/macb.c:1503: error: initializer element is not constant
drivers/net/ethernet/cadence/macb.c:1503: error: (near initialization for 'macb_driver.driver.of_match_table')
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Use the generic gpiolib gpio_is_valid() function to test
if the phy IRQ line GPIO is actually provided.

For non-connected or non-existing phy IRQ lines, -EINVAL
value is used for phy_irq_pin field of struct at91_eth_data.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: David S. Miller <davem@davemloft.net>

Add the Cadence macb ethernet controller in at91sam9g45 and at91sam9g20
.dtsi and enable it in at91sam9m10g45ek and usb_a9g20 board device tree file.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Allow the device tree to provide the mac address and the phy mode.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[nicolas.ferre@atmel.com: change "compatible" node property, doc and DT hwaddr]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
[jamie@jamieiles.com: add "gem" compatibility strings and doc]
Acked-by: Jamie Iles<jamie@jamieiles.com>
Acked-by: David S. Miller <davem@davemloft.net>

Merge branch 'hsmmc' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into omap/hsmmc

Add support for base-board MMC slot
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Abhilash K V <abhilash.kv@ti.com>
[tony@atomide.com: updated subject]
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch fixes the following error message which appears
while intializing MMC1 on the AM3517 EVM base-board:
    mmc0: host doesn't support card's voltages
    mmc0: error -22 whilst initialising SD card
The ocr_mask, which enumerates the volatges supported by the
MMC card was not being indicated before, assuming that a separate
Vcc regulator maybe another controllable regulator driver would be
doing this. This patch statically specifies a subset of the voltages
supported by the MMC driver, which are provided by the current fixed
voltage regulator on AM3517 EVM.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Abhilash K V <abhilash.kv@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The Devkit8000 uses a TWL4030 pin for card detection.
Thats why the error:
_omap_mux_init_gpio: Could not set gpio192
occurs.

This patch checks that the pin is on OMAP before
calling omap_mux_init_gpio.
Signed-off-by: Thomas Weber <weber@corscience.de>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>

AM35x MMC 2 controller has internal clock loopback setting which cannot
be utilized without this patch and thus SDIO devices connected to this
controller and depend on this setting will fail to initialize.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>

Declare support for keeping the power of the wlan chip
while suspended. this is needed for Wakeup-On-Wireless.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add pm_caps field to omap2_hsmmc_info and omap_mmc_slot_data
structs, so we will be able to indicate mmc pm capabilities
in the board file.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

When an mmc card has the MMC_PM_KEEP_POWER flag, it shouldn't
be powered off on suspend (and thus doesn't have to be powered-on
on resume)

While on it, change the suspend flow a bit, to make it a bit
easier to follow.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

arch/arm/mach-pxa/spitz_pm.c: In function ‘spitz_presuspend’:
arch/arm/mach-pxa/spitz_pm.c:112:2: error: implicit declaration of
function ‘GPIO_bit’
make[1]: *** [arch/arm/mach-pxa/spitz_pm.o] Error 1

GPIO_bit() is moved into <linux/gpio-pxa.h>.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

arch/arm/mach-pxa/corgi_pm.c: In function ‘corgi_should_wakeup’:
arch/arm/mach-pxa/corgi_pm.c:102:2: error: implicit declaration of
function ‘GPIO_bit’
make[1]: *** [arch/arm/mach-pxa/corgi_pm.o] Error 1
make: *** [arch/arm/mach-pxa] Error 2
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Conflicts:
	drivers/net/ethernet/cadence/Kconfig

Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@ti.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

This is for supporting saif record function.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@ti.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@ti.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add master_mode and master_id in platfrom_data since it's board
specific and board knows it.
Then we can remove the function pointer in platfrom_data to make
the driver more devicetree friendly.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2: (31 commits)
  ocfs2: avoid unaligned access to dqc_bitmap
  ocfs2: Use filemap_write_and_wait() instead of write_inode_now()
  ocfs2: honor O_(D)SYNC flag in fallocate
  ocfs2: Add a missing journal credit in ocfs2_link_credits() -v2
  ocfs2: send correct UUID to cleancache initialization
  ocfs2: Commit transactions in error cases -v2
  ocfs2: make direntry invalid when deleting it
  fs/ocfs2/dlm/dlmlock.c: free kmem_cache_zalloc'd data using kmem_cache_free
  ocfs2: Avoid livelock in ocfs2_readpage()
  ocfs2: serialize unaligned aio
  ocfs2: Implement llseek()
  ocfs2: Fix ocfs2_page_mkwrite()
  ocfs2: Add comment about orphan scanning
  ocfs2: Clean up messages in the fs
  ocfs2/cluster: Cluster up now includes network connections too
  ocfs2/cluster: Add new function o2net_fill_node_map()
  ocfs2/cluster: Fix output in file elapsed_time_in_ms
  ocfs2/dlm: dlmlock_remote() needs to account for remastery
  ocfs2/dlm: Take inflight reference count for remotely mastered resources too
  ocfs2/dlm: Cleanup dlm_wait_for_node_death() and dlm_wait_for_node_recovery()
  ...

The dqc_bitmap field of struct ocfs2_local_disk_chunk is 32-bit aligned,
but not 64-bit aligned.  The dqc_bitmap is accessed by ocfs2_set_bit(),
ocfs2_clear_bit(), ocfs2_test_bit(), or ocfs2_find_next_zero_bit().  These
are wrapper macros for ext2_*_bit() which need to take an unsigned long
aligned address (though some architectures are able to handle unaligned
address correctly)

So some 64bit architectures may not be able to access the dqc_bitmap
correctly.

This avoids such unaligned access by using another wrapper functions for
ext2_*_bit().  The code is taken from fs/ext4/mballoc.c which also need to
handle unaligned bitmap access.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Joel Becker <jlbec@evilplan.org>

* 'fixes' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
  ARM: 7182/1: ARM cpu topology: fix warning
  ARM: 7181/1: Restrict kprobes probing SWP instructions to ARMv5 and below
  ARM: 7180/1: Change kprobes testcase with unpredictable STRD instruction
  ARM: 7177/1: GIC: avoid skipping non-existent PPIs in irq_start calculation
  ARM: 7176/1: cpu_pm: register GIC PM notifier only once
  ARM: 7175/1: add subname parameter to mfp_set_groupg callers
  ARM: 7174/1: Fix build error in kprobes test code on Thumb2 kernels
  ARM: 7172/1: dma: Drop GFP_COMP for DMA memory allocations
  ARM: 7171/1: unwind: add unwind directives to bitops assembly macros
  ARM: 7170/2: fix compilation breakage in entry-armv.S
  ARM: 7168/1: use cache type functions for arch_get_unmapped_area
  ARM: perf: check that we have a platform device when reserving PMU
  ARM: 7166/1: Use PMD_SHIFT instead of PGDIR_SHIFT in dma-consistent.c
  ARM: 7165/2: PL330: Fix typo in _prepare_ccr()
  ARM: 7163/2: PL330: Only register usable channels
  ARM: 7162/1: errata: tidy up Kconfig options for PL310 errata workarounds
  ARM: 7161/1: errata: no automatic store buffer drain
  ARM: perf: initialise used_mask for fake PMU during validation
  ARM: PMU: remove pmu_init declaration
  ARM: PMU: re-export release_pmu symbol to modules

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: fix meta data raid-repair merge problem
  Btrfs: skip allocation attempt from empty cluster
  Btrfs: skip block groups without enough space for a cluster
  Btrfs: start search for new cluster at the beginning
  Btrfs: reset cluster's max_size when creating bitmap
  Btrfs: initialize new bitmaps' list
  Btrfs: fix oops when calling statfs on readonly device
  Btrfs: Don't error on resizing FS to same size
  Btrfs: fix deadlock on metadata reservation when evicting a inode
  Fix URL of btrfs-progs git repository in docs
  btrfs scrub: handle -ENOMEM from init_ipath()

Commit 4a54c8c1 introduced raid-repair, killing the individual
readpage_io_failed_hook entries from inode.c and disk-io.c. Commit
4bb31e92 introduced new readahead code, adding a readpage_io_failed_hook to
disk-io.c.

The raid-repair commit had logic to disable raid-repair, if
readpage_io_failed_hook is set. Thus, the readahead commit effectively
disabled raid-repair for meta data.

This commit changes the logic to always attempt raid-repair when needed and
call the readpage_io_failed_hook in case raid-repair fails. This is much
more straight forward and should have been like that from the beginning.
Signed-off-by: Jan Schmidt <list.btrfs@jan-o-sch.net>
Reported-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Chris Mason <chris.mason@oracle.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  IB: Fix RCU lockdep splats
  IB/ipoib: Prevent hung task or softlockup processing multicast response
  IB/qib: Fix over-scheduling of QSFP work
  RDMA/cxgb4: Fix retry with MPAv1 logic for MPAv2
  RDMA/cxgb4: Fix iw_cxgb4 count_rcqes() logic
  IB/qib: Don't use schedule_work()

* 'dt-for-linus' of git://sources.calxeda.com/kernel/linux:
  of: Add Silicon Image vendor prefix
  of/irq: of_irq_init: add check for parent equal to child node

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: twl: fix twl4030 support for smps regulators
  regulator: fix use after free bug
  regulator: aat2870: Fix the logic of checking if no id is matched in aat2870_get_regulator

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (45 commits)
  ARM: ux500: update defconfig
  ARM: u300: update defconfig
  ARM: at91: enable additional boards in existing soc defconfig files
  ARM: at91: refresh soc defconfig files for 3.2
  ARM: at91: rename defconfig files appropriately
  ARM: OMAP2+: Fix Compilation error when omap_l3_noc built as module
  ARM: OMAP2+: Remove empty io.h
  ARM: OMAP2: select ARM_AMBA if OMAP3_EMU is defined
  ARM: OMAP: smartreflex: fix IRQ handling bug
  ARM: OMAP: PM: only register TWL with voltage layer when device is present
  ARM: OMAP: hwmod: Fix the addr space, irq, dma count APIs
  arm: mx28: fix bit operation in clock setting
  ARM: imx: export imx_ioremap
  ARM: imx/mm-imx3: conditionally compile i.MX31 and i.MX35 code
  ARM: mx5: Fix checkpatch warnings in cpu-imx5.c
  MAINTAINERS: Add missing directory
  ARM: imx: drop 'ARCH_MX31' and 'ARCH_MX35'
  ARM: imx6q: move clock register map to machine_desc.map_io
  ARM: pxa168/gplugd: add the correct SSP device
  ARM: Update mach-types to fix mxs build breakage
  ...

kernel/sched.c:7354:2: warning: initialization from incompatible pointer type

Align cpu_coregroup_mask prototype interface with sched_domain_mask_f typedef
use int cpu instead of unsigned int cpu

Cc: <stable@vger.kernel.org>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The SWP instruction is deprecated on ARMv6 and with ARMv7 it will be
UNDEFINED when CONFIG_SWP_EMULATE is selected. In this case, probing a
SWP instruction will cause an oops when the kprobes emulation code
executes an undefined instruction.

As the SWP instruction should be rare or non-existent in kernels for
ARMv6 and later, we can simply avoid these problems by not allowing
probing of these.
Reported-by: Leif Lindholm <leif.lindholm@arm.com>
Tested-by: Leif Lindholm <leif.lindholm@arm.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

There is a kprobes testcase for the instruction "strd r2, [r3], r4".
This has unpredictable behaviour as it uses r3 for register writeback
addressing and also stores it to memory.

On a cortex A9, this testcase would fail because the instruction writes
the updated value of r3 to memory, whereas the kprobes emulation code
writes the original value.

Fix this by changing testcase to used r5 instead of r3.
Reported-by: Leif Lindholm <leif.lindholm@arm.com>
Tested-by: Leif Lindholm <leif.lindholm@arm.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

If we don't have a cluster, don't bother trying to allocate from it,
jumping right away to the attempt to allocate a new cluster.
Signed-off-by: Alexandre Oliva <oliva@lsd.ic.unicamp.br>
Signed-off-by: Chris Mason <chris.mason@oracle.com>

We test whether a block group has enough free space to hold the
requested block, but when we're doing clustered allocation, we can
save some cycles by testing whether it has enough room for the cluster
upfront, otherwise we end up attempting to set up a cluster and
failing.  Only in the NO_EMPTY_SIZE loop do we attempt an unclustered
allocation, and by then we'll have zeroed the cluster size, so this
patch won't stop us from using the block group as a last resort.
Signed-off-by: Alexandre Oliva <oliva@lsd.ic.unicamp.br>
Signed-off-by: Chris Mason <chris.mason@oracle.com>

Instead of starting at zero (offset is always zero), request a cluster
starting at search_start, that denotes the beginning of the current
block group.
Signed-off-by: Alexandre Oliva <oliva@lsd.ic.unicamp.br>
Signed-off-by: Chris Mason <chris.mason@oracle.com>

The field that indicates the size of the largest contiguous chunk of
free space in the cluster is not initialized when setting up bitmaps,
it's only increased when we find a larger contiguous chunk.  We end up
retaining a larger value than appropriate for highly-fragmented
clusters, which may cause pointless searches for large contiguous
groups, and even cause clusters that do not meet the density
requirements to be set up.
Signed-off-by: Alexandre Oliva <oliva@lsd.ic.unicamp.br>
Signed-off-by: Chris Mason <chris.mason@oracle.com>

We're failing to create clusters with bitmaps because
setup_cluster_no_bitmap checks that the list is empty before inserting
the bitmap entry in the list for setup_cluster_bitmap, but the list
field is only initialized when it is restored from the on-disk free
space cache, or when it is written out to disk.

Besides a potential race condition due to the multiple use of the list
field, filesystem performance severely degrades over time: as we use
up all non-bitmap free extents, the try-to-set-up-cluster dance is
done at every metadata block allocation.  For every block group, we
fail to set up a cluster, and after failing on them all up to twice,
we fall back to the much slower unclustered allocation.

To make matters worse, before the unclustered allocation, we try to
create new block groups until we reach the 1% threshold, which
introduces additional bitmaps and thus block groups that we'll iterate
over at each metadata block request.