- 09 Mar, 2016 40 commits
-
-
Simon South authored
commit 02322ac9 upstream. This patch applies the microphone-related fix created for the Acer Aspire E1-572 to the E1-472 as well, as it uses the same Realtek ALC282 CODEC and demonstrates the same issues. This patch allows an external, headset microphone to be used and limits the gain on the (quite noisy) internal microphone. Signed-off-by:
Simon South <simon@simonsouth.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Takashi Iwai authored
commit 6236d8bb upstream. The X32 ABI takes the same alignment like x86-64, and this may result in the incompatible struct size from ia32. Unfortunately, we hit this in some control ABI: struct snd_ctl_elem_value differs between them due to the position of 64bit variable array. This ends up with the unknown ioctl (ENOTTY) error. The fix is to add the compat entries for the new aligned struct. Reported-and-tested-by:
Steven Newbury <steve@snewbury.org.uk> Signed-off-by:
-
Dennis Kadioglu authored
commit 17e2df46 upstream. Plantronics DA45 does not support reading the sample rate which leads to many lines of "cannot get freq at ep 0x4" and "cannot get freq at ep 0x84". This patch adds the USB ID of the DA45 to quirks.c and avoids those error messages. Signed-off-by:
Dennis Kadioglu <denk@post.com> Signed-off-by:
-
Hans Verkuil authored
commit 0ba4581c upstream. The 5 volt detect functionality broke in 3.14: the code reads IO register 0x70 again after it has already been cleared. Instead it should use the cached irq_reg_0x70 value and the io_write to 0x71 to clear 0x70 can be dropped since this has already been done. Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by:
-
Robert Jarzmik authored
commit f1692127 upstream. While testing audio with pxa2xx-ac97, underrun were happening while the user application was correctly feeding the music. Debug proved that the cyclic transfer is not cyclic, ie. the last descriptor did not loop on the first. Another issue is that the descriptor length was always set to 8192, because of an trivial operator issue. This was tested on a pxa27x platform. Fixes: a57e16cf ("dmaengine: pxa: add pxa dmaengine driver") Reported-by:
Vasily Khoruzhick <anarsoul@gmail.com> Tested-by:
Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
-
David Woodhouse authored
commit be629c62 upstream. When a directory is deleted, we don't take too much care about killing off all the dirents that belong to it — on the basis that on remount, the scan will conclude that the directory is dead anyway. This doesn't work though, when the deleted directory contained a child directory which was moved *out*. In the early stages of the fs build we can then end up with an apparent hard link, with the child directory appearing both in its true location, and as a child of the original directory which are this stage of the mount process we don't *yet* know is defunct. To resolve this, take out the early special-casing of the "directories shall not have hard links" rule in jffs2_build_inode_pass1(), and let the normal nlink processing happen for directories as well as other inodes. Then later in the build process we can set ic->pino_nlink to the parent inode#, as is required for directories during normal operaton, instead of the nlink. And complain only *then* about hard links which are still in evidence even after killing off all the unreachable paths. Reported-by:
Liu Song <liu.song11@zte.com.cn> Signed-off-by:
David Woodhouse <David.Woodhouse@intel.com> Signed-off-by:
-
David Woodhouse authored
commit 49e91e70 upstream. With this fix, all code paths should now be obtaining the page lock before f->sem. Reported-by:
Szabó Tamás <sztomi89@gmail.com> Tested-by:
Thomas Betker <thomas.betker@rohde-schwarz.com> Signed-off-by:
-
Thomas Betker authored
commit 157078f6 upstream. This reverts commit 5ffd3412 ("jffs2: Fix lock acquisition order bug in jffs2_write_begin"). The commit modified jffs2_write_begin() to remove a deadlock with jffs2_garbage_collect_live(), but this introduced new deadlocks found by multiple users. page_lock() actually has to be called before mutex_lock(&c->alloc_sem) or mutex_lock(&f->sem) because jffs2_write_end() and jffs2_readpage() are called with the page locked, and they acquire c->alloc_sem and f->sem, resp. In other words, the lock order in jffs2_write_begin() was correct, and it is the jffs2_garbage_collect_live() path that has to be changed. Revert the commit to get rid of the new deadlocks, and to clear the way for a better fix of the original deadlock. Reported-by:
Deng Chao <deng.chao1@zte.com.cn> Reported-by:
Ming Liu <liu.ming50@gmail.com> Reported-by:
wangzaiwei <wangzaiwei@top-vision.cn> Signed-off-by:
-
Filipe Manana authored
commit 909c3a22 upstream. When looking for orphan roots during mount we can end up hitting a BUG_ON() (at root-item.c:btrfs_find_orphan_roots()) if a log tree is replayed and qgroups are enabled. This is because after a log tree is replayed, a transaction commit is made, which triggers qgroup extent accounting which in turn does backref walking which ends up reading and inserting all roots in the radix tree fs_info->fs_root_radix, including orphan roots (deleted snapshots). So after the log tree is replayed, when finding orphan roots we hit the BUG_ON with the following trace: [118209.182438] ------------[ cut here ]------------ [118209.183279] kernel BUG at fs/btrfs/root-tree.c:314! [118209.184074] invalid opcode: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC [118209.185123] Modules linked in: btrfs dm_flakey dm_mod crc32c_generic ppdev xor raid6_pq evdev sg parport_pc parport acpi_cpufreq tpm_tis tpm psmouse processor i2c_piix4 serio_raw pcspkr i2c_core button loop autofs4 ext4 crc16 mbcache jbd2 sd_mod sr_mod cdrom ata_generic virtio_scsi ata_piix libata virtio_pci virtio_ring virtio scsi_mod e1000 floppy [last unloaded: btrfs] [118209.186318] CPU: 14 PID: 28428 Comm: mount Tainted: G W 4.5.0-rc5-btrfs-next-24+ #1 [118209.186318] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS by qemu-project.org 04/01/2014 [118209.186318] task: ffff8801ec131040 ti: ffff8800af34c000 task.ti: ffff8800af34c000 [118209.186318] RIP: 0010:[<ffffffffa04237d7>] [<ffffffffa04237d7>] btrfs_find_orphan_roots+0x1fc/0x244 [btrfs] [118209.186318] RSP: 0018:ffff8800af34faa8 EFLAGS: 00010246 [118209.186318] RAX: 00000000ffffffef RBX: 00000000ffffffef RCX: 0000000000000001 [118209.186318] RDX: 0000000080000000 RSI: 0000000000000001 RDI: 00000000ffffffff [118209.186318] RBP: ffff8800af34fb08 R08: 0000000000000001 R09: 0000000000000000 [118209.186318] R10: ffff8800af34f9f0 R11: 6db6db6db6db6db7 R12: ffff880171b97000 [118209.186318] R13: ffff8801ca9d65e0 R14: ffff8800afa2e000 R15: 0000160000000000 [118209.186318] FS: 00007f5bcb914840(0000) GS:ffff88023edc0000(0000) knlGS:0000000000000000 [118209.186318] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b [118209.186318] CR2: 00007f5bcaceb5d9 CR3: 00000000b49b5000 CR4: 00000000000006e0 [118209.186318] Stack: [118209.186318] fffffbffffffffff 010230ffffffffff 0101000000000000 ff84000000000000 [118209.186318] fbffffffffffffff 30ffffffffffffff 0000000000000101 ffff880082348000 [118209.186318] 0000000000000000 ffff8800afa2e000 ffff8800afa2e000 0000000000000000 [118209.186318] Call Trace: [118209.186318] [<ffffffffa042e2db>] open_ctree+0x1e37/0x21b9 [btrfs] [118209.186318] [<ffffffffa040a753>] btrfs_mount+0x97e/0xaed [btrfs] [118209.186318] [<ffffffff8108e1c0>] ? trace_hardirqs_on+0xd/0xf [118209.186318] [<ffffffff8117b87e>] mount_fs+0x67/0x131 [118209.186318] [<ffffffff81192d2b>] vfs_kern_mount+0x6c/0xde [118209.186318] [<ffffffffa0409f81>] btrfs_mount+0x1ac/0xaed [btrfs] [118209.186318] [<ffffffff8108e1c0>] ? trace_hardirqs_on+0xd/0xf [118209.186318] [<ffffffff8108c26b>] ? lockdep_init_map+0xb9/0x1b3 [118209.186318] [<ffffffff8117b87e>] mount_fs+0x67/0x131 [118209.186318] [<ffffffff81192d2b>] vfs_kern_mount+0x6c/0xde [118209.186318] [<ffffffff81195637>] do_mount+0x8a6/0x9e8 [118209.186318] [<ffffffff8119598d>] SyS_mount+0x77/0x9f [118209.186318] [<ffffffff81493017>] entry_SYSCALL_64_fastpath+0x12/0x6b [118209.186318] Code: 64 00 00 85 c0 89 c3 75 24 f0 41 80 4c 24 20 20 49 8b bc 24 f0 01 00 00 4c 89 e6 e8 e8 65 00 00 85 c0 89 c3 74 11 83 f8 ef 75 02 <0f> 0b 4c 89 e7 e8 da 72 00 00 eb 1c 41 83 bc 24 00 01 00 00 00 [118209.186318] RIP [<ffffffffa04237d7>] btrfs_find_orphan_roots+0x1fc/0x244 [btrfs] [118209.186318] RSP <ffff8800af34faa8> [118209.230735] ---[ end trace 83938f987d85d477 ]--- So fix this by not treating the error -EEXIST, returned when attempting to insert a root already inserted by the backref walking code, as an error. The following test case for xfstests reproduces the bug: seq=`basename $0` seqres=$RESULT_DIR/$seq echo "QA output created by $seq" tmp=/tmp/$$ status=1 # failure is the default! trap "_cleanup; exit \$status" 0 1 2 3 15 _cleanup() { _cleanup_flakey cd / rm -f $tmp.* } # get standard environment, filters and checks . ./common/rc . ./common/filter . ./common/dmflakey # real QA test starts here _supported_fs btrfs _supported_os Linux _require_scratch _require_dm_target flakey _require_metadata_journaling $SCRATCH_DEV rm -f $seqres.full _scratch_mkfs >>$seqres.full 2>&1 _init_flakey _mount_flakey _run_btrfs_util_prog quota enable $SCRATCH_MNT # Create 2 directories with one file in one of them. # We use these just to trigger a transaction commit later, moving the file from # directory a to directory b and doing an fsync against directory a. mkdir $SCRATCH_MNT/a mkdir $SCRATCH_MNT/b touch $SCRATCH_MNT/a/f sync # Create our test file with 2 4K extents. $XFS_IO_PROG -f -s -c "pwrite -S 0xaa 0 8K" $SCRATCH_MNT/foobar | _filter_xfs_io # Create a snapshot and delete it. This doesn't really delete the snapshot # immediately, just makes it inaccessible and invisible to user space, the # snapshot is deleted later by a dedicated kernel thread (cleaner kthread) # which is woke up at the next transaction commit. # A root orphan item is inserted into the tree of tree roots, so that if a # power failure happens before the dedicated kernel thread does the snapshot # deletion, the next time the filesystem is mounted it resumes the snapshot # deletion. _run_btrfs_util_prog subvolume snapshot $SCRATCH_MNT $SCRATCH_MNT/snap _run_btrfs_util_prog subvolume delete $SCRATCH_MNT/snap # Now overwrite half of the extents we wrote before. Because we made a snapshpot # before, which isn't really deleted yet (since no transaction commit happened # after we did the snapshot delete request), the non overwritten extents get # referenced twice, once by the default subvolume and once by the snapshot. $XFS_IO_PROG -c "pwrite -S 0xbb 4K 8K" $SCRATCH_MNT/foobar | _filter_xfs_io # Now move file f from directory a to directory b and fsync directory a. # The fsync on the directory a triggers a transaction commit (because a file # was moved from it to another directory) and the file fsync leaves a log tree # with file extent items to replay. mv $SCRATCH_MNT/a/f $SCRATCH_MNT/a/b $XFS_IO_PROG -c "fsync" $SCRATCH_MNT/a $XFS_IO_PROG -c "fsync" $SCRATCH_MNT/foobar echo "File digest before power failure:" md5sum $SCRATCH_MNT/foobar | _filter_scratch # Now simulate a power failure and mount the filesystem to replay the log tree. # After the log tree was replayed, we used to hit a BUG_ON() when processing # the root orphan item for the deleted snapshot. This is because when processing # an orphan root the code expected to be the first code inserting the root into # the fs_info->fs_root_radix radix tree, while in reallity it was the second # caller attempting to do it - the first caller was the transaction commit that # took place after replaying the log tree, when updating the qgroup counters. _flakey_drop_and_remount echo "File digest before after failure:" # Must match what he got before the power failure. md5sum $SCRATCH_MNT/foobar | _filter_scratch _unmount_flakey status=0 exit Fixes: 2d9e9776 ("Btrfs: use btrfs_get_fs_root in resolve_indirect_ref") Signed-off-by:
Filipe Manana <fdmanana@suse.com> Reviewed-by:
Qu Wenruo <quwenruo@cn.fujitsu.com> Signed-off-by:
Chris Mason <clm@fb.com> Signed-off-by:
-
Gabor Juhos authored
commit 01836176 upstream. The RB532 platform specific irq_to_gpio() implementation has been removed with commit 832f5dac ("MIPS: Remove all the uses of custom gpio.h"). Now the platform uses the generic stub which causes the following error: pata-rb532-cf pata-rb532-cf: no GPIO found for irq149 pata-rb532-cf: probe of pata-rb532-cf failed with error -2 Drop the irq_to_gpio() call and get the GPIO number from platform data instead. After this change, the driver works again: scsi host0: pata-rb532-cf ata1: PATA max PIO4 irq 149 ata1.00: CFA: CF 1GB, 20080820, max MWDMA4 ata1.00: 1989792 sectors, multi 0: LBA ata1.00: configured for PIO4 scsi 0:0:0:0: Direct-Access ATA CF 1GB 0820 PQ: 0\ ANSI: 5 sd 0:0:0:0: [sda] 1989792 512-byte logical blocks: (1.01 GB/971 MiB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't\ support DPO or FUA sda: sda1 sda2 sd 0:0:0:0: [sda] Attached SCSI disk Fixes: 832f5dac ("MIPS: Remove all the uses of custom gpio.h") Cc: Alban Bedel <albeu@free.fr> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by:
Gabor Juhos <juhosg@openwrt.org> Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit e57cbaf0 upstream. Commit 9f616680 "tracing: Allow triggers to filter for CPU ids and process names" added a 'comm' filter that will filter events based on the current tasks struct 'comm'. But this now hides the ability to filter events that have a 'comm' field too. For example, sched_migrate_task trace event. That has a 'comm' field of the task to be migrated. echo 'comm == "bash"' > events/sched_migrate_task/filter will now filter all sched_migrate_task events for tasks named "bash" that migrates other tasks (in interrupt context), instead of seeing when "bash" itself gets migrated. This fix requires a couple of changes. 1) Change the look up order for filter predicates to look at the events fields before looking at the generic filters. 2) Instead of basing the filter function off of the "comm" name, have the generic "comm" filter have its own filter_type (FILTER_COMM). Test against the type instead of the name to assign the filter function. 3) Add a new "COMM" filter that works just like "comm" but will filter based on the current task, even if the trace event contains a "comm" field. Do the same for "cpu" field, adding a FILTER_CPU and a filter "CPU". Fixes: 9f616680 "tracing: Allow triggers to filter for CPU ids and process names" Reported-by:
Matt Fleming <matt@codeblueprint.co.uk> Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Manuel Lauss authored
commit dc8b4afc upstream. The HPCP bit is set by bioses for on-board sata ports either because they think sata is hotplug capable in general or to allow Windows to display a "device eject" icon on ports which are routed to an external connector bracket. However in Redhat Bugzilla #1310682, users report that with kernel 4.4, where this bit test first appeared, a lot of partitions on sata drives are now mounted automatically. This patch should fix redhat and a lot of other distros which unconditionally automount all devices which have the "removable" bit set. Signed-off-by:
Manuel Lauss <manuel.lauss@gmail.com> Signed-off-by:
-
Todd E Brandt authored
commit 92f9e179 upstream. Pause/unpause graph tracing around do_suspend_lowlevel as it has inconsistent call/return info after it jumps to the wakeup vector. The graph trace buffer will otherwise become misaligned and may eventually crash and hang on suspend. To reproduce the issue and test the fix: Run a function_graph trace over suspend/resume and set the graph function to suspend_devices_and_enter. This consistently hangs the system without this fix. Signed-off-by:
Todd Brandt <todd.e.brandt@linux.intel.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Ard Biesheuvel authored
commit dfd55ad8 upstream. Commit dd006da2 ("arm64: mm: increase VA range of identity map") made some changes to the memory mapping code to allow physical memory to reside at an offset that exceeds the size of the virtual mapping. However, since the size of the vmemmap area is proportional to the size of the VA area, but it is populated relative to the physical space, we may end up with the struct page array being mapped outside of the vmemmap region. For instance, on my Seattle A0 box, I can see the following output in the dmesg log. vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000 ( 8 GB maximum) 0xffffffbfc0000000 - 0xffffffbfd0000000 ( 256 MB actual) We can fix this by deciding that the vmemmap region is not a projection of the physical space, but of the virtual space above PAGE_OFFSET, i.e., the linear region. This way, we are guaranteed that the vmemmap region is of sufficient size, and we can even reduce the size by half. Signed-off-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
-
Alexandra Yates authored
commit f5bdd66c upstream. This patch complements the list of device IDs previously added for lewisburg sata. Signed-off-by:
Alexandra Yates <alexandra.yates@linux.intel.com> Signed-off-by:
-
Tejun Heo authored
commit a1a0e23e upstream. If cgroup writeback is in use, inodes can be scheduled for asynchronous wb switching. Before 5ff8eaac ("writeback: keep superblock pinned during cgroup writeback association switches"), this could race with umount leading to super_block being destroyed while inodes are pinned for wb switching. 5ff8eaac fixed it by bumping s_active while wb switches are in flight; however, this allowed in-flight wb switches to make umounts asynchronous when the userland expected synchronosity - e.g. fsck immediately following umount may fail because the device is still busy. This patch removes the problematic super_block pinning and instead makes generic_shutdown_super() flush in-flight wb switches. wb switches are now executed on a dedicated isw_wq so that they can be flushed and isw_nr_in_flight keeps track of the number of in-flight wb switches so that flushing can be avoided in most cases. v2: Move cgroup_writeback_umount() further below and add MS_ACTIVE check in inode_switch_wbs() as Jan an Al suggested. Signed-off-by:
Tahsin Erdogan <tahsin@google.com> Cc: Jan Kara <jack@suse.cz> Cc: Al Viro <viro@ZenIV.linux.org.uk> Link: http://lkml.kernel.org/g/CAAeU0aNCq7LGODvVGRU-oU_o-6enii5ey0p1c26D1ZzYwkDc5A@mail.gmail.com Fixes: 5ff8eaac ("writeback: keep superblock pinned during cgroup writeback association switches") Reviewed-by:
Jan Kara <jack@suse.cz> Tested-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Ming Lei authored
commit 7bcd79ac upstream. The bio passed to bio_will_gap() may be fast cloned from upper layer(dm, md, bcache, fs, ...), or from bio splitting in block core. Unfortunately bio_will_gap() just figures out the last bvec via 'bi_io_vec[prev->bi_vcnt - 1]' directly, and this way is obviously wrong. This patch introduces two helpers for getting the first and last bvec of one bio for fixing the issue. Reported-by:
Sagi Grimberg <sagig@dev.mellanox.co.il> Reviewed-by:
Sagi Grimberg <sagig@mellanox.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Ming Lei <ming.lei@canonical.com> Signed-off-by:
-
Harvey Hunt authored
commit 4ee34ea3 upstream. The id buffer in ata_device is a DMA target, but it isn't explicitly cacheline aligned. Due to this, adjacent fields can be overwritten with stale data from memory on non coherent architectures. As a result, the kernel is sometimes unable to communicate with an ATA device. Fix this by ensuring that the id buffer is cacheline aligned. This issue is similar to that fixed by Commit 84bda12a ("libata: align ap->sector_buf"). Signed-off-by:
Harvey Hunt <harvey.hunt@imgtec.com> Cc: linux-kernel@vger.kernel.org Signed-off-by:
-
Arnd Bergmann authored
commit 287e6611 upstream. As reported by Soohoon Lee, the HDIO_GET_32BIT ioctl does not work correctly in compat mode with libata. I have investigated the issue further and found multiple problems that all appeared with the same commit that originally introduced HDIO_GET_32BIT handling in libata back in linux-2.6.8 and presumably also linux-2.4, as the code uses "copy_to_user(arg, &val, 1)" to copy a 'long' variable containing either 0 or 1 to user space. The problems with this are: * On big-endian machines, this will always write a zero because it stores the wrong byte into user space. * In compat mode, the upper three bytes of the variable are updated by the compat_hdio_ioctl() function, but they now contain uninitialized stack data. * The hdparm tool calling this ioctl uses a 'static long' variable to store the result. This means at least the upper bytes are initialized to zero, but calling another ioctl like HDIO_GET_MULTCOUNT would fill them with data that remains stale when the low byte is overwritten. Fortunately libata doesn't implement any of the affected ioctl commands, so this would only happen when we query both an IDE and an ATA device in the same command such as "hdparm -N -c /dev/hda /dev/sda" * The libata code for unknown reasons started using ATA_IOC_GET_IO32 and ATA_IOC_SET_IO32 as aliases for HDIO_GET_32BIT and HDIO_SET_32BIT, while the ioctl commands that were added later use the normal HDIO_* names. This is harmless but rather confusing. This addresses all four issues by changing the code to use put_user() on an 'unsigned long' variable in HDIO_GET_32BIT, like the IDE subsystem does, and by clarifying the names of the ioctl commands. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Reported-by:
Soohoon Lee <Soohoon.Lee@f5.com> Tested-by:
-
Arindam Nath authored
commit 0b39c531 upstream. In amdgpu_connector_hotplug(), we need to start DP link training only after we have received DPCD. The function amdgpu_atombios_dp_get_dpcd() returns non-zero value only when an error condition is met, otherwise returns zero. So in case the function encounters an error, we need to skip rest of the code and return from amdgpu_connector_hotplug() immediately. Only when we are successfull in reading DPCD pin, we should carry on with turning-on the monitor. Signed-off-by:
Arindam Nath <arindam.nath@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Chunming Zhou authored
commit 9cac5373 upstream. Select between me and pfp properly. Signed-off-by:
Chunming Zhou <David1.Zhou@amd.com> Reviewed-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
-
Christian König authored
commit feebe91a upstream. We never ported that back to CIK, so we could run into VM faults here. Signed-off-by:
-
Alex Deucher authored
commit eda1d1cf upstream. On CI, we need to see if the number of crtcs changes to determine whether or not we need to upload the mclk table again. In practice we don't currently upload the mclk table again after the initial load. The only reason you would would be to add new states, e.g., for arbitrary mclk setting which is not currently supported. Acked-by:
Jordan Lazare <Jordan.Lazare@amd.com> Acked-by:
-
Alex Deucher authored
commit 5e031d9f upstream. On CI, we need to see if the number of crtcs changes to determine whether or not we need to upload the mclk table again. In practice we don't currently upload the mclk table again after the initial load. The only reason you would would be to add new states, e.g., for arbitrary mclk setting which is not currently supported. Acked-by:
-
Timothy Pearson authored
commit 2d02b8bd upstream. During DRAM initialization on certain ASpeed devices, an incorrect bit (bit 10) was checked in the "SDRAM Bus Width Status" register to determine DRAM width. Query bit 6 instead in accordance with the Aspeed AST2050 datasheet v1.05. Signed-off-by:
Timothy Pearson <tpearson@raptorengineeringinc.com> Signed-off-by:
Dave Airlie <airlied@redhat.com> Signed-off-by:
-
Mike Christie authored
commit 8a9ebe71 upstream. In a couple places we are not converting to/from the Linux block layer 512 bytes sectors. 1. The request queue values and what we do are a mismatch of things: max_discard_sectors - This is in linux block layer 512 byte sectors. We are just copying this to max_unmap_lba_count. discard_granularity - This is in bytes. We are converting it to Linux block layer 512 byte sectors. discard_alignment - This is in bytes. We are just copying this over. The problem is that the core LIO code exports these values in spc_emulate_evpd_b0 and we use them to test request arguments in sbc_execute_unmap, but we never convert to the block size we export to the initiator. If we are not using 512 byte sectors then we are exporting the wrong values or are checks are off. And, for the discard_alignment/bytes case we are just plain messed up. 2. blkdev_issue_discard's start and number of sector arguments are supposed to be in linux block layer 512 byte sectors. We are currently passing in the values we get from the initiator which might be based on some other sector size. There is a similar problem in iblock_execute_write_same where the bio functions want values in 512 byte sectors but we are passing in what we got from the initiator. Signed-off-by:
Mike Christie <mchristi@redhat.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> [ kamal: backport to 4.4-stable: no unmap_zeroes_data ] Signed-off-by:
Kamal Mostafa <kamal@canonical.com> Signed-off-by:
-
Joerg Roedel authored
commit e6a8c9b3 upstream. In the PCI hotplug path of the Intel IOMMU driver, replace the usage of the BUS_NOTIFY_DEL_DEVICE notifier, which is executed before the driver is unbound from the device, with BUS_NOTIFY_REMOVED_DEVICE, which runs after that. This fixes a kernel BUG being triggered in the VT-d code when the device driver tries to unmap DMA buffers and the VT-d driver already destroyed all mappings. Reported-by:
Stefani Seibold <stefani@seibold.net> Signed-off-by:
Joerg Roedel <jroedel@suse.de> Signed-off-by:
-
Suravee Suthikulpanit authored
commit 38e45d02 upstream. The setup code for the performance counters in the AMD IOMMU driver tests whether the counters can be written. It tests to setup a counter for device 00:00.0, which fails on systems where this particular device is not covered by the IOMMU. Fix this by not relying on device 00:00.0 but only on the IOMMU being present. Signed-off-by:
Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com> Signed-off-by:
-
Jay Cornwall authored
commit 358875fd upstream. The AMD Family 15h Models 30h-3Fh (Kaveri) BIOS and Kernel Developer's Guide omitted part of the BIOS IOMMU L2 register setup specification. Without this setup the IOMMU L2 does not fully respect write permissions when handling an ATS translation request. The IOMMU L2 will set PTE dirty bit when handling an ATS translation with write permission request, even when PTE RW bit is clear. This may occur by direct translation (which would cause a PPR) or by prefetch request from the ATC. This is observed in practice when the IOMMU L2 modifies a PTE which maps a pagecache page. The ext4 filesystem driver BUGs when asked to writeback these (non-modified) pages. Enable ATS write permission check in the Kaveri IOMMU L2 if BIOS has not. Signed-off-by:
Jay Cornwall <jay@jcornwall.me> Signed-off-by:
-
Michael S. Tsirkin authored
commit 4cad67fc upstream. Calling return copy_to_user(...) in an ioctl will not do the right thing if there's a pagefault: copy_to_user returns the number of bytes not copied in this case. Fix up kvm to do return copy_to_user(...)) ? -EFAULT : 0; everywhere. Acked-by:
Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
Marc Zyngier <marc.zyngier@arm.com> Signed-off-by:
-
Paolo Bonzini authored
commit 70e4da7a upstream. Commit 172b2386 ("KVM: x86: fix missed hardware breakpoints", 2016-02-10) worked around a case where the debug registers are not loaded correctly on preemption and on the first entry to KVM_RUN. However, Xiao Guangrong pointed out that the root cause must be that KVM_DEBUGREG_BP_ENABLED is not being set correctly. This can indeed happen due to the lazy debug exit mechanism, which does not call kvm_update_dr7. Fix it by replacing the existing loop (more or less equivalent to kvm_update_dr0123) with calls to all the kvm_update_dr* functions. Fixes: 172b2386Reviewed-by:
Xiao Guangrong <guangrong.xiao@linux.intel.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Michael S. Tsirkin authored
commit 8160c4e4 upstream. Calling return copy_to_user(...) in an ioctl will not do the right thing if there's a pagefault: copy_to_user returns the number of bytes not copied in this case. Fix up vfio to do return copy_to_user(...)) ? -EFAULT : 0; everywhere. Signed-off-by:
Alex Williamson <alex.williamson@redhat.com> Signed-off-by:
-
Yadan Fan authored
commit 1ee9f4bd upstream. This issue is caused by commit 02323db1 ("cifs: fix cifs_uniqueid_to_ino_t not to ever return 0"), when BITS_PER_LONG is 64 on s390x, the corresponding cifs_uniqueid_to_ino_t() function will cast 64-bit fileid to 32-bit by using (ino_t)fileid, because ino_t (typdefed __kernel_ino_t) is int type. It's defined in arch/s390/include/uapi/asm/posix_types.h #ifndef __s390x__ typedef unsigned long __kernel_ino_t; ... #else /* __s390x__ */ typedef unsigned int __kernel_ino_t; So the #ifdef condition is wrong for s390x, we can just still use one cifs_uniqueid_to_ino_t() function with comparing sizeof(ino_t) and sizeof(u64) to choose the correct execution accordingly. Signed-off-by:
Yadan Fan <ydfan@suse.com> Signed-off-by:
Steve French <smfrench@gmail.com> Signed-off-by:
-
Pavel Shilovsky authored
commit 6cc3b242 upstream. For interim responses we only need to parse a header and update a number credits. Now it is done for all SMB2+ command except SMB2_READ which is wrong. Fix this by adding such processing. Signed-off-by:
Pavel Shilovsky <pshilovsky@samba.org> Tested-by:
Shirish Pargaonkar <shirishpargaonkar@gmail.com> Signed-off-by:
-
Justin Maggard authored
commit deb7deff upstream. When opening a file, SMB2_open() attempts to parse the lease state from the SMB2 CREATE Response. However, the parsing code was not careful to ensure that the create contexts are not empty or invalid, which can lead to out- of-bounds memory access. This can be seen easily by trying to read a file from a OSX 10.11 SMB3 server. Here is sample crash output: BUG: unable to handle kernel paging request at ffff8800a1a77cc6 IP: [<ffffffff8828a734>] SMB2_open+0x804/0x960 PGD 8f77067 PUD 0 Oops: 0000 [#1] SMP Modules linked in: CPU: 3 PID: 2876 Comm: cp Not tainted 4.5.0-rc3.x86_64.1+ #14 Hardware name: NETGEAR ReadyNAS 314 /ReadyNAS 314 , BIOS 4.6.5 10/11/2012 task: ffff880073cdc080 ti: ffff88005b31c000 task.ti: ffff88005b31c000 RIP: 0010:[<ffffffff8828a734>] [<ffffffff8828a734>] SMB2_open+0x804/0x960 RSP: 0018:ffff88005b31fa08 EFLAGS: 00010282 RAX: 0000000000000015 RBX: 0000000000000000 RCX: 0000000000000006 RDX: 0000000000000000 RSI: 0000000000000246 RDI: ffff88007eb8c8b0 RBP: ffff88005b31fad8 R08: 666666203d206363 R09: 6131613030383866 R10: 3030383866666666 R11: 00000000000002b0 R12: ffff8800660fd800 R13: ffff8800a1a77cc2 R14: 00000000424d53fe R15: ffff88005f5a28c0 FS: 00007f7c8a2897c0(0000) GS:ffff88007eb80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: ffff8800a1a77cc6 CR3: 000000005b281000 CR4: 00000000000006e0 Stack: ffff88005b31fa70 ffffffff88278789 00000000000001d3 ffff88005f5a2a80 ffffffff00000003 ffff88005d029d00 ffff88006fde05a0 0000000000000000 ffff88005b31fc78 ffff88006fde0780 ffff88005b31fb2f 0000000100000fe0 Call Trace: [<ffffffff88278789>] ? cifsConvertToUTF16+0x159/0x2d0 [<ffffffff8828cf68>] smb2_open_file+0x98/0x210 [<ffffffff8811e80c>] ? __kmalloc+0x1c/0xe0 [<ffffffff882685f4>] cifs_open+0x2a4/0x720 [<ffffffff88122cef>] do_dentry_open+0x1ff/0x310 [<ffffffff88268350>] ? cifsFileInfo_get+0x30/0x30 [<ffffffff88123d92>] vfs_open+0x52/0x60 [<ffffffff88131dd0>] path_openat+0x170/0xf70 [<ffffffff88097d48>] ? remove_wait_queue+0x48/0x50 [<ffffffff88133a29>] do_filp_open+0x79/0xd0 [<ffffffff8813f2ca>] ? __alloc_fd+0x3a/0x170 [<ffffffff881240c4>] do_sys_open+0x114/0x1e0 [<ffffffff881241a9>] SyS_open+0x19/0x20 [<ffffffff8896e257>] entry_SYSCALL_64_fastpath+0x12/0x6a Code: 4d 8d 6c 07 04 31 c0 4c 89 ee e8 47 6f e5 ff 31 c9 41 89 ce 44 89 f1 48 c7 c7 28 b1 bd 88 31 c0 49 01 cd 4c 89 ee e8 2b 6f e5 ff <45> 0f b7 75 04 48 c7 c7 31 b1 bd 88 31 c0 4d 01 ee 4c 89 f6 e8 RIP [<ffffffff8828a734>] SMB2_open+0x804/0x960 RSP <ffff88005b31fa08> CR2: ffff8800a1a77cc6 ---[ end trace d9f69ba64feee469 ]--- Signed-off-by:
Justin Maggard <jmaggard@netgear.com> Signed-off-by:
-
Jean-Philippe Brucker authored
commit a1e533ec upstream. Since commit 27a4c827 fbcon: use the cursor blink interval provided by vt two attempts have been made at fixing a possible hang caused by cursor_timer_handler. That function registers a timer to be triggered at "jiffies + fbcon_ops.cur_blink_jiffies". A new case had been encountered during initialisation of clcd-pl11x: fbcon_fb_registered do_fbcon_takeover -> do_register_con_driver fbcon_startup (A) add_cursor_timer (with cur_blink_jiffies = 0) -> do_bind_con_driver visual_init fbcon_init (B) cur_blink_jiffies = msecs_to_jiffies(vc->vc_cur_blink_ms); If we take an softirq anywhere between A and B (and we do), cursor_timer_handler executes indefinitely. Instead of patching all possible paths that lead to this case one at a time, fix the issue at the source and initialise cur_blink_jiffies to 200ms when allocating fbcon_ops. This was its default value before aforesaid commit. fbcon_cursor or fbcon_init will refine this value downstream. Signed-off-by:
Jean-Philippe Brucker <jean-philippe.brucker@arm.com> Tested-by:
Scot Doyle <lkml14@scotdoyle.com> Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by:
-
Owen Hofmann authored
commit 2680d6da upstream. vmx.c writes the TSC_MULTIPLIER field in vmx_vcpu_load, but only when a vcpu has migrated physical cpus. Record the last value written and update in vmx_vcpu_load on any change, otherwise a cpu migration must occur for TSC frequency scaling to take effect. Fixes: ff2c3a18Signed-off-by:
Owen Hofmann <osh@google.com> Signed-off-by:
-
Michael S. Tsirkin authored
commit 0178fd7d upstream. Returning directly whatever copy_to_user(...) or copy_from_user(...) returns may not do the right thing if there's a pagefault: copy_to_user/copy_from_user return the number of bytes not copied in this case, but ioctls need to return -EFAULT instead. Fix up kvm on mips to do return copy_to_user(...)) ? -EFAULT : 0; and return copy_from_user(...)) ? -EFAULT : 0; everywhere. Signed-off-by:
-
Helge Deller authored
commit 98e8b6c9 upstream. Mike Frysinger reported that his ptrace testcase showed strange behaviour on parisc: It was not possible to avoid a syscall and the return value of a syscall couldn't be changed. To modify a syscall number, we were missing to save the new syscall number to gr20 which is then picked up later in assembly again. The effect that the return value couldn't be changed is a side-effect of another bug in the assembly code. When a process is ptraced, userspace expects each syscall to report entrance and exit of a syscall. If a syscall number was given which doesn't exist, we jumped to the normal syscall exit code instead of informing userspace that the (non-existant) syscall exits. This unexpected behaviour confuses userspace and thus the bug was misinterpreted as if we can't change the return value. This patch fixes both problems and was tested on 64bit kernel with 32bit userspace. Signed-off-by:
Helge Deller <deller@gmx.de> Cc: Mike Frysinger <vapier@gentoo.org> Tested-by:
Mike Frysinger <vapier@gentoo.org> Signed-off-by:
-
Murali Karicheri authored
commit 79e3f4a8 upstream. Commit cbce7900 ("PCI: designware: Make driver arch-agnostic") changed the host bridge sysdata pointer from the ARM pci_sys_data to the DesignWare pcie_port structure, and changed pcie-designware.c to reflect that. But it did not change the corresponding code in pci-keystone-dw.c, so it caused crashes on Keystone: Unable to handle kernel NULL pointer dereference at virtual address 00000030 pgd = c0003000 [00000030] *pgd=80000800004003, *pmd=00000000 Internal error: Oops: 206 [#1] PREEMPT SMP ARM CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.4.2-00139-gb74f926 #2 Hardware name: Keystone PC is at ks_dw_pcie_msi_irq_unmask+0x24/0x58 Change pci-keystone-dw.c to expect sysdata to be the struct pcie_port pointer. [bhelgaas: changelog] Fixes: cbce7900 ("PCI: designware: Make driver arch-agnostic") Signed-off-by:
Murali Karicheri <m-karicheri2@ti.com> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> CC: Zhou Wang <wangzhou1@hisilicon.com> Signed-off-by:
-
