Some peripheral clocks on SAMA7G5 supports requesting parent to change
its rate (image related clocks: csi, csi2dc, isc). Add support
so that if registered with this option the clock rate to be
requested from parent.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-14-git-send-email-claudiu.beznea@microchip.comSigned-off-by: Stephen Boyd <sboyd@kernel.org>

Add master clock support (MCK1..4) for SAMA7G5. SAMA7G5's PMC has
multiple master clocks feeding different subsystems. One of them
feeds image subsystem and is changeable based on image subsystem
needs.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-13-git-send-email-claudiu.beznea@microchip.comSigned-off-by: Stephen Boyd <sboyd@kernel.org>

Add mux table option. This is necessary for IP versions that has
gaps in the range of available clock sources (e.g. SAMA7G5).
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-12-git-send-email-claudiu.beznea@microchip.comSigned-off-by: Stephen Boyd <sboyd@kernel.org>

Pass the ID of changeable parent at registration. This will allow
the scalability of this clock driver with regards to the changeable
parent ID for versions of this IP where changeable parent is not the
last one in the parents list (e.g. SAMA7G5). With this the clock flags
are set to zero in case we have no changeable parent. Also in
clk_generated_best_diff() the *best_diff variable is check against
tmp_diff variable using ">=" operator instead of ">" so that in case
the requested frequency could be obtained using fix parents + gck
dividers but the clock also supports changeable parent to be able
to force the usage of the changeable parent.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-11-git-send-email-claudiu.beznea@microchip.comSigned-off-by: Stephen Boyd <sboyd@kernel.org>

Replace conditional operator with double logical not as code
may be simpler to read.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-10-git-send-email-claudiu.beznea@microchip.comSigned-off-by: Stephen Boyd <sboyd@kernel.org>

Chapter 57.7.5 of SAM9X60 datasheet specifies that the maximum drift of
this oscillator is +- 3KHz. Use that value and the formula at [1]
or the calculator at [2] to compute the PPB value.

[1] https://www.everythingrf.com/rf-calculators/ppm-to-hz-calculator
[2] https://www.changpuak.ch/electronics/ppm_to_Hz_converter.php

Fixes: 04bcc427 ("clk: at91: sckc: add support for SAM9X60")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-9-git-send-email-claudiu.beznea@microchip.comSigned-off-by: Stephen Boyd <sboyd@kernel.org>

Main RC oscillator frequency is 12MHz according to datasheet
(chapter 27.2).

Fixes: 01e2113d ("clk: at91: add sam9x60 pmc driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1595403506-8209-8-git-send-email-claudiu.beznea@microchip.comSigned-off-by: Stephen Boyd <sboyd@kernel.org>

In commit a436c2a4 ("clk: at91: add sam9x60 PLL driver")
the fractional part of PLL wasn't set on registers but it was
calculated and taken into account for determining div and mul
(see sam9x60_pll_get_best_div_mul()).

Fixes: a436c2a4 ("clk: at91: add sam9x60 PLL driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-7-git-send-email-claudiu.beznea@microchip.comSigned-off-by: Stephen Boyd <sboyd@kernel.org>

According to datasheet the range of 600-1200MHz is for the
frequency generated by the fractional part of the PLL (namely
Fcorepllck according to datasheet). With this in mind the output
range of the PLL itself (fractional + div), taking into account
that the divider is 8 bits wide, is 600/256-1200Hz=2.3-1200MHz.

Fixes: a436c2a4 ("clk: at91: add sam9x60 PLL driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-6-git-send-email-claudiu.beznea@microchip.comSigned-off-by: Stephen Boyd <sboyd@kernel.org>

Use logical or for range check. In case bestrate is not in
characteristics->output[0].min..characteristics->output[0].max
range we should return -ERANGE.

Fixes: a436c2a4 ("clk: at91: add sam9x60 PLL driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1595403506-8209-5-git-send-email-claudiu.beznea@microchip.comSigned-off-by: Stephen Boyd <sboyd@kernel.org>

According to datasheet mul mask is on bits 31..24.

Fixes: a436c2a4 ("clk: at91: add sam9x60 PLL driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1595403506-8209-4-git-send-email-claudiu.beznea@microchip.comSigned-off-by: Stephen Boyd <sboyd@kernel.org>

Check best_rate against available clock ranges.

Fixes: df70aeef ("clk: at91: add generated clock driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1595403506-8209-3-git-send-email-claudiu.beznea@microchip.comSigned-off-by: Stephen Boyd <sboyd@kernel.org>

__clk_determine_rate() may return error. Skip the current step
in case of error.

Fixes: 1a1a36d7 ("clk: at91: clk-generated: make gclk determine audio_pll rate")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1595403506-8209-2-git-send-email-claudiu.beznea@microchip.comSigned-off-by: Stephen Boyd <sboyd@kernel.org>

syscon_node_to_regmap() will make the created regmap get and enable the
first clock it can parse from the device tree. This clock is not needed to
access the registers and should not be enabled at that time.

Use device_node_to_regmap to resolve this as it looks up the regmap in
the same list but doesn't care about the clocks. This issue is detected
by lockdep when booting the sama5d3 with a device tree containing the
new clk bindings.

This fix already happened in 6956eb33 ("clk: at91: fix possible
deadlock") for the drivers that had been migrated to the new clk binding
back then. This does the same for the new drivers as well.

Fixes: 01e2113d ("clk: at91: add sam9x60 pmc driver")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://lore.kernel.org/r/20200703073236.23923-1-a.fatoum@pengutronix.deAcked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

Pull SafeSetID update from Micah Morton:
 "Add additional LSM hooks for SafeSetID

  SafeSetID is capable of making allow/deny decisions for set*uid calls
  on a system, and we want to add similar functionality for set*gid
  calls.

  The work to do that is not yet complete, so probably won't make it in
  for v5.8, but we are looking to get this simple patch in for v5.8
  since we have it ready.

  We are planning on the rest of the work for extending the SafeSetID
  LSM being merged during the v5.9 merge window"

* tag 'LSM-add-setgid-hook-5.8-author-fix' of git://github.com/micah-morton/linux:
  security: Add LSM hooks to set*gid syscalls

The SafeSetID LSM uses the security_task_fix_setuid hook to filter
set*uid() syscalls according to its configured security policy. In
preparation for adding analagous support in the LSM for set*gid()
syscalls, we add the requisite hook here. Tested by putting print
statements in the security_task_fix_setgid hook and seeing them get hit
during kernel boot.
Signed-off-by: Thomas Cedeno <thomascedeno@google.com>
Signed-off-by: Micah Morton <mortonm@chromium.org>

Pull btrfs updates from David Sterba:
 "This reverts the direct io port to iomap infrastructure of btrfs
  merged in the first pull request. We found problems in invalidate page
  that don't seem to be fixable as regressions or without changing iomap
  code that would not affect other filesystems.

  There are four reverts in total, but three of them are followup
  cleanups needed to revert a43a67a2 cleanly. The result is the
  buffer head based implementation of direct io.

  Reverts are not great, but under current circumstances I don't see
  better options"

* tag 'for-5.8-part2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  Revert "btrfs: switch to iomap_dio_rw() for dio"
  Revert "fs: remove dio_end_io()"
  Revert "btrfs: remove BTRFS_INODE_READDIO_NEED_LOCK"
  Revert "btrfs: split btrfs_direct_IO to read and write part"

Pull networking fixes from David Miller:

 1) Fix cfg80211 deadlock, from Johannes Berg.

 2) RXRPC fails to send norigications, from David Howells.

 3) MPTCP RM_ADDR parsing has an off by one pointer error, fix from
    Geliang Tang.

 4) Fix crash when using MSG_PEEK with sockmap, from Anny Hu.

 5) The ucc_geth driver needs __netdev_watchdog_up exported, from
    Valentin Longchamp.

 6) Fix hashtable memory leak in dccp, from Wang Hai.

 7) Fix how nexthops are marked as FDB nexthops, from David Ahern.

 8) Fix mptcp races between shutdown and recvmsg, from Paolo Abeni.

 9) Fix crashes in tipc_disc_rcv(), from Tuong Lien.

10) Fix link speed reporting in iavf driver, from Brett Creeley.

11) When a channel is used for XSK and then reused again later for XSK,
    we forget to clear out the relevant data structures in mlx5 which
    causes all kinds of problems. Fix from Maxim Mikityanskiy.

12) Fix memory leak in genetlink, from Cong Wang.

13) Disallow sockmap attachments to UDP sockets, it simply won't work.
    From Lorenz Bauer.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (83 commits)
  net: ethernet: ti: ale: fix allmulti for nu type ale
  net: ethernet: ti: am65-cpsw-nuss: fix ale parameters init
  net: atm: Remove the error message according to the atomic context
  bpf: Undo internal BPF_PROBE_MEM in BPF insns dump
  libbpf: Support pre-initializing .bss global variables
  tools/bpftool: Fix skeleton codegen
  bpf: Fix memlock accounting for sock_hash
  bpf: sockmap: Don't attach programs to UDP sockets
  bpf: tcp: Recv() should return 0 when the peer socket is closed
  ibmvnic: Flush existing work items before device removal
  genetlink: clean up family attributes allocations
  net: ipa: header pad field only valid for AP->modem endpoint
  net: ipa: program upper nibbles of sequencer type
  net: ipa: fix modem LAN RX endpoint id
  net: ipa: program metadata mask differently
  ionic: add pcie_print_link_status
  rxrpc: Fix race between incoming ACK parser and retransmitter
  net/mlx5: E-Switch, Fix some error pointer dereferences
  net/mlx5: Don't fail driver on failure to create debugfs
  net/mlx5e: CT: Fix ipv6 nat header rewrite actions
  ...

This reverts commit a43a67a2.

This patch reverts the main part of switching direct io implementation
to iomap infrastructure. There's a problem in invalidate page that
couldn't be solved as regression in this development cycle.

The problem occurs when buffered and direct io are mixed, and the ranges
overlap. Although this is not recommended, filesystems implement
measures or fallbacks to make it somehow work. In this case, fallback to
buffered IO would be an option for btrfs (this already happens when
direct io is done on compressed data), but the change would be needed in
the iomap code, bringing new semantics to other filesystems.

Another problem arises when again the buffered and direct ios are mixed,
invalidation fails, then -EIO is set on the mapping and fsync will fail,
though there's no real error.

There have been discussions how to fix that, but revert seems to be the
least intrusive option.

Link: https://lore.kernel.org/linux-btrfs/20200528192103.xm45qoxqmkw7i5yl@fiona/Signed-off-by: David Sterba <dsterba@suse.com>

On AM65xx MCU CPSW2G NUSS and 66AK2E/L NUSS allmulti setting does not allow
unregistered mcast packets to pass.

This happens, because ALE VLAN entries on these SoCs do not contain port
masks for reg/unreg mcast packets, but instead store indexes of
ALE_VLAN_MASK_MUXx_REG registers which intended for store port masks for
reg/unreg mcast packets.
This path was missed by commit 9d1f6447 ("net: ethernet: ti: ale: fix
seeing unreg mcast packets with promisc and allmulti disabled").

Hence, fix it by taking into account ALE type in cpsw_ale_set_allmulti().

Fixes: 9d1f6447 ("net: ethernet: ti: ale: fix seeing unreg mcast packets with promisc and allmulti disabled")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ALE parameters structure is created on stack, so it has to be reset
before passing to cpsw_ale_create() to avoid garbage values.

Fixes: 93a76530 ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexei Starovoitov says:

====================
pull-request: bpf 2020-06-12

The following pull-request contains BPF updates for your *net* tree.

We've added 26 non-merge commits during the last 10 day(s) which contain
a total of 27 files changed, 348 insertions(+), 93 deletions(-).

The main changes are:

1) sock_hash accounting fix, from Andrey.

2) libbpf fix and probe_mem sanitizing, from Andrii.

3) sock_hash fixes, from Jakub.

4) devmap_val fix, from Jesper.

5) load_bytes_relative fix, from YiFei.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Looking into the context (atomic!) and the error message should be dropped.
Signed-off-by: Liao Pingfang <liao.pingfang@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull more cifs updates from Steve French:
 "12 cifs/smb3 fixes, 2 for stable.

   - add support for idsfromsid on create and chgrp/chown allowing
     ability to save owner information more naturally for some workloads

   - improve query info (getattr) when SMB3.1.1 posix extensions are
     negotiated by using new query info level"

* tag '5.8-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  smb3: Add debug message for new file creation with idsfromsid mount option
  cifs: fix chown and chgrp when idsfromsid mount option enabled
  smb3: allow uid and gid owners to be set on create with idsfromsid mount option
  smb311: Add tracepoints for new compound posix query info
  smb311: add support for using info level for posix extensions query
  smb311: Add support for lookup with posix extensions query info
  smb311: Add support for SMB311 query info (non-compounded)
  SMB311: Add support for query info using posix extensions (level 100)
  smb3: add indatalen that can be a non-zero value to calculation of credit charge in smb2 ioctl
  smb3: fix typo in mount options displayed in /proc/mounts
  cifs: Add get_security_type_str function to return sec type.
  smb3: extend fscache mount volume coherency check

Let's keep "git status" happy and quiet.

Fixes: 9762dc14 ("samples: add binderfs sample program
Fixes: fca5e949 ("samples: binderfs: really compile this sample and fix build issues")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

I'm not convinced the script makes useful automaed help lines anyway,
but since we're trying to deprecate the use of "---help---" in Kconfig
files, let's fix the doc example code too.

See commit a7f7f624 ("treewide: replace '---help---' in Kconfig
files with 'help'")

Cc: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull more Kbuild updates from Masahiro Yamada:

 - fix build rules in binderfs sample

 - fix build errors when Kbuild recurses to the top Makefile

 - covert '---help---' in Kconfig to 'help'

* tag 'kbuild-v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  treewide: replace '---help---' in Kconfig files with 'help'
  kbuild: fix broken builds because of GZIP,BZIP2,LZOP variables
  samples: binderfs: really compile this sample and fix build issues

Pull more SCSI updates from James Bottomley:
 "This is the set of changes collected since just before the merge
  window opened. It's mostly minor fixes in drivers.

  The one non-driver set is the three optical disk (sr) changes where
  two are error path fixes and one is a helper conversion.

  The big driver change is the hpsa compat_alloc_userspace rework by Al
  so he can kill the remaining user. This has been tested and acked by
  the maintainer"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (21 commits)
  scsi: acornscsi: Fix an error handling path in acornscsi_probe()
  scsi: storvsc: Remove memset before memory freeing in storvsc_suspend()
  scsi: cxlflash: Remove an unnecessary NULL check
  scsi: ibmvscsi: Don't send host info in adapter info MAD after LPM
  scsi: sr: Fix sr_probe() missing deallocate of device minor
  scsi: sr: Fix sr_probe() missing mutex_destroy
  scsi: st: Convert convert get_user_pages() --> pin_user_pages()
  scsi: target: Rename target_setup_cmd_from_cdb() to target_cmd_parse_cdb()
  scsi: target: Fix NULL pointer dereference
  scsi: target: Initialize LUN in transport_init_se_cmd()
  scsi: target: Factor out a new helper, target_cmd_init_cdb()
  scsi: hpsa: hpsa_ioctl(): Tidy up a bit
  scsi: hpsa: Get rid of compat_alloc_user_space()
  scsi: hpsa: Don't bother with vmalloc for BIG_IOCTL_Command_struct
  scsi: hpsa: Lift {BIG_,}IOCTL_Command_struct copy{in,out} into hpsa_ioctl()
  scsi: ufs: Remove redundant urgent_bkop_lvl initialization
  scsi: ufs: Don't update urgent bkops level when toggling auto bkops
  scsi: qedf: Remove redundant initialization of variable rc
  scsi: mpt3sas: Fix memset() in non-RDPQ mode
  scsi: iscsi: Fix reference count leak in iscsi_boot_create_kobj
  ...

Pull i2c updates from Wolfram Sang:
 "I2C has quite some patches for you this time. I hope it is the move to
  per-driver-maintainers which is now showing results. We will see.

  The big news is two new drivers (Nuvoton NPCM and Qualcomm CCI),
  larger refactoring of the Designware, Tegra, and PXA drivers, the
  Cadence driver supports being a slave now, and there is support to
  instanciate SPD eeproms for well-known cases (which will be
  user-visible because the i801 driver supports it), and some
  devm_platform_ioremap_resource() conversions which blow up the
  diffstat.

  Note that I applied the Nuvoton driver quite late, so some minor fixup
  patches arrived during the merge window. I chose to apply them right
  away because they were trivial"

* 'i2c/for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (109 commits)
  i2c: Drop stray comma in MODULE_AUTHOR statements
  i2c: npcm7xx: npcm_i2caddr[] can be static
  MAINTAINERS: npcm7xx: Add maintainer for Nuvoton NPCM BMC
  i2c: npcm7xx: Fix a couple of error codes in probe
  i2c: icy: Fix build with CONFIG_AMIGA_PCMCIA=n
  i2c: npcm7xx: Remove unnecessary parentheses
  i2c: npcm7xx: Add support for slave mode for Nuvoton
  i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver
  dt-bindings: i2c: npcm7xx: add NPCM I2C controller
  i2c: pxa: don't error out if there's no pinctrl
  i2c: add 'single-master' property to generic bindings
  i2c: designware: Add Baikal-T1 System I2C support
  i2c: designware: Move reg-space remapping into a dedicated function
  i2c: designware: Retrieve quirk flags as early as possible
  i2c: designware: Convert driver to using regmap API
  i2c: designware: Discard Cherry Trail model flag
  i2c: designware: Add Baytrail sem config DW I2C platform dependency
  i2c: designware: slave: Set DW I2C core module dependency
  i2c: designware: Use `-y` to build multi-object modules
  dt-bindings: i2c: dw: Add Baikal-T1 SoC I2C controller
  ...

Pull more media updates from Mauro Carvalho Chehab:

 - a set of atomisp patches. They remove several abstraction layers, and
   fixes clang and gcc warnings (that were hidden via some macros that
   were disabling 4 or 5 types of warnings there). There are also some
   important fixes and sensor auto-detection on newer BIOSes via ACPI
   _DCM tables.

 - some fixes

* tag 'media/v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (95 commits)
  media: rkvdec: Fix H264 scaling list order
  media: v4l2-ctrls: Unset correct HEVC loop filter flag
  media: videobuf2-dma-contig: fix bad kfree in vb2_dma_contig_clear_max_seg_size
  media: v4l2-subdev.rst: correct information about v4l2 events
  media: s5p-mfc: Properly handle dma_parms for the allocated devices
  media: medium: cec: Make MEDIA_CEC_SUPPORT default to n if !MEDIA_SUPPORT
  media: cedrus: Implement runtime PM
  media: cedrus: Program output format during each run
  media: atomisp: improve ACPI/DMI detection logs
  media: Revert "media: atomisp: add Asus Transform T101HA ACPI vars"
  media: Revert "media: atomisp: Add some ACPI detection info"
  media: atomisp: improve sensor detection code to use _DSM table
  media: atomisp: get rid of an iomem abstraction layer
  media: atomisp: get rid of a string_support.h abstraction layer
  media: atomisp: use strscpy() instead of less secure variants
  media: atomisp: set DFS to MAX if sensor doesn't report fps
  media: atomisp: use different dfs failed messages
  media: atomisp: change the detection of ISP2401 at runtime
  media: atomisp: use macros from intel-family.h
  media: atomisp: don't set hpll_freq twice with different values
  ...

Pull libnvdimm updates from Dan Williams:
 "Small collection of cleanups to rework usage of ->queuedata and the
  GUID api"

* tag 'libnvdimm-for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  nvdimm/pmem: stop using ->queuedata
  nvdimm/btt: stop using ->queuedata
  nvdimm/blk: stop using ->queuedata
  libnvdimm: Replace guid_copy() with import_guid() where it makes sense

Let's keep "git status" happy and quiet.

Fixes: f5b5a164 ("Add sample notification program")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull iomap fix from Darrick Wong:
 "A single iomap bug fix for a variable type mistake on 32-bit
  architectures, fixing an integer overflow problem in the unshare
  actor"

* tag 'iomap-5.8-merge-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  iomap: Fix unsharing of an extent >2GB on a 32-bit machine

Pull xfs fix from Darrick Wong:
 "We've settled down into the bugfix phase; this one fixes a resource
  leak on an error bailout path"

* tag 'xfs-5.8-merge-9' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: Add the missed xfs_perag_put() for xfs_ifree_cluster()

Pull 9p update from Dominique Martinet:
 "Another very quiet cycle... Only one commit: increase the size of the
  ring used for xen transport"

* tag '9p-for-5.8' of git://github.com/martinetd/linux:
  9p/xen: increase XEN_9PFS_RING_ORDER

Pull powerpc fix from Michael Ellerman:
 "One fix for a recent change which broke nested KVM guests on Power9.

  Thanks to Alexey Kardashevskiy"

* tag 'powerpc-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  KVM: PPC: Fix nested guest RC bits update

Pull ARM fixes from Russell King:

 - fix for "hex" Kconfig default to use 0x0 rather than 0 to allow these
   to be removed from defconfigs

 - fix from Ard Biesheuvel for EFI HYP mode booting

* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: 8985/1: efi/decompressor: deal with HYP mode boot gracefully
  ARM: 8984/1: Kconfig: set default ZBOOT_ROM_TEXT/BSS value to 0x0

Pull OpenRISC update from Stafford Horne:
 "One patch found wile I was getting the glibc port ready: fix issue
  with clone TLS arg getting overwritten"

* tag 'for-linus' of git://github.com/openrisc/linux:
  openrisc: Fix issue with argument clobbering for clone/fork

Pull alpha updates from Matt Turner:
 "A few changes for alpha. They're mostly small janitorial fixes but
  there's also a build fix and most notably a patch from Mikulas that
  fixes a hang on boot on the Avanti platform, which required quite a
  bit of work and review"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha:
  alpha: Fix build around srm_sysrq_reboot_op
  alpha: c_next should increase position index
  alpha: Replace sg++ with sg = sg_next(sg)
  alpha: fix memory barriers so that they conform to the specification
  alpha: remove unneeded semicolon in sys_eiger.c
  alpha: remove unneeded semicolon in osf_sys.c
  alpha: Replace strncmp with str_has_prefix
  alpha: fix rtc port ranges
  alpha: Kconfig: pedantic formatting