This patch adds Cortex-A53 CPU cores of R8A7796 SoC, and sets a total of
6 cores (2 x Cortex-A57 + 4 x Cortex-A53).

Based on a patch by Takeshi Kihara in the BSP.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a device node for the Cortex-A53 L2 cache-controller.

The L2 cache for the Cortex-A53 CPU cores is 512 KiB large (organized as
32 KiB x 16 ways).

Extracted from a patch by Takeshi Kihara in the BSP.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Enable the performance monitor unit for the Cortex-A57 cores on the
R8A7796 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch adds Cortex-A57 CPU cores to R8A7796 SoC for a total of
2 x Cortex-A57.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Rebased]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Current	Audio-DMAC is assigned "rx" as Audio-DMAC0, "tx" as Audio-DMAC1.
Thus, DVC "tx" should be assigned as Audio-DMAC1, instead of Audio-DMAC0.

Because of this, current platform board (using SRC/DVC/SSI)
Playback/Capture both will use same Audio-DMAC0
(but it depends on audio data path).

First note is that this "rx" and "tx" are from each IP point,
it doesn't mean Playback/Capture.
Second note is that Audio DMAC assigned on DT is only for
Audio-DMAC, Audio-DMAC-peri-peri has no entry.

=> Audio-DMAC
-> Audio-DMAC-peri-peri
-- HW connection

Playback case

	[Mem] => [SRC]--[DVC] -> [SSI]--[Codec]
	      rx ~~~~~~~~~~~~
Capture

	[Mem] <= [DVC]--[SRC] <- [SSI]--[Codec]
	      tx ~~~~~~~~~~~~
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The EthernetAVB should not depend on the bootloader to setup correct
drive-strength values. Values for drive-strength where found by
examining the registers after the bootloader has configured the
registers and successfully used the EthernetAVB.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The Cortex-A57 cache controller is an integrated controller, and thus
the device node representing it should not have a unit-addresses or reg
property.

Fixes: 1561f207 ("arm64: dts: r8a7796: Add Renesas R8A7796 SoC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The Cortex-A57/A53 cache controllers are integrated controllers, and
thus the device nodes representing them should not have unit-addresses
or reg properties.

Fixes: 6f7bf82c ("arm64: dts: r8a7795: Fix W=1 dtc warnings")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

>From PSCI v1.0, Suspend-to-RAM is supported via SYSTEM_SUSPEND PSCI
function call. Hence, upgrade PSCI version for R-Car M3-W to support
Suspend-to-RAM.

The Suspend-to-RAM is highly dependent on ARM Trusted Firwmare support
since necessary callback functions will be registered after a query
to ARM Trusted Firmware about SYSTEM_SUSPEND support.

Since PSCI v1.0 is backward compatible with PSCI v0.2, CPU Hotplug and
CPUIdle should be able to work normally with this change.
Signed-off-by: Khiem Nguyen <khiem.nguyen.xt@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Keep "arm,psci-0.2"]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

>From PSCI v1.0, Suspend-to-RAM is supported via SYSTEM_SUSPEND PSCI
function call. Hence, upgrade PSCI version for R-Car H3 to support
Suspend-to-RAM.

The Suspend-to-RAM is highly dependent on ARM Trusted Firwmare support
since necessary callback functions will be registered after a query
to ARM Trusted Firmware about SYSTEM_SUSPEND support.

Since PSCI v1.0 is backward compatible with PSCI v0.2, CPU Hotplug and
CPUIdle should be able to work normally with this change.
Signed-off-by: Khiem Nguyen <khiem.nguyen.xt@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Keep "arm,psci-0.2"]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Enable the performance monitor unit for the Cortex-A53 cores on the
R8A7795 SoC.

Extracted from a patch by Takeshi Kihara in the BSP.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch adds Cortex-A53 CPU cores to r8a7795 SoC for a total of 8
cores (4 x Cortex-A57 + 4 x Cortex-A53).

Based on work by Takeshi Kihara and Dirk Behme.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Enables the SCIF hooked up to the DEBUG1 connector.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the device nodes for all R-Car H3 SCIF serial ports, incl. clocks
and power domain.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the device nodes for all HSCIF serial ports, incl. clocks, and
power domain.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
[simon: express register size in hex; refer to power domain in changelog]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Set PHY rxc-skew-ps to 1500 and all other values to their default values.

This is intended to to address failures in the case of 1Gbps communication
using the by salvator-x board with the KSZ9031RNX phy. This has been
reported to occur with both the r8a7795 (H3) and r8a7796 (M3-W) SoCs.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Since commit 61fccb2d ("ravb: Add tx and rx clock internal delays mode
of APSR") the EthernetAVB driver enables tx and rx clock internal delay
modes (TDM and RDM) depending on the phy mode as follows:

    phy mode   | ASPR delay mode
    -----------+----------------
    rgmii-id   | TDM and RDM
    rgmii-rxid | RDM
    rgmii-txid | TDM

And prior to the above commit no internal delay mode settings were
implemented for any phy mode.

With this and the above change present tx internal delay mode is enabled
which has been observed to address failures in the case of 1Gbps
communication using the by salvator-x board with the KSZ9031RNX phy. This
has been reported to occur with both the r8a7795 (H3) and r8a7796 (M3-W)
SoCs.

With the above patch present but this patch present tx and rx internal
delay modes are enabled; and with the above patch and this present absent
no internal delay modes are enabled. In both cases failures have been
observed when using 1Gbps communication in the environments described
above.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Set PHY rxc-skew-ps to 1500 and all other values to their default values.

This is intended to to address failures in the case of 1Gbps communication
using the by h3ulcb board with the KSZ9031RNX phy.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Set PHY rxc-skew-ps to 1500 and all other values to their default values.

This is intended to to address failures in the case of 1Gbps communication
using the by salvator-x board with the KSZ9031RNX phy. This has been
reported to occur with both the r8a7795 (H3) and r8a7796 (M3-W) SoCs.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Since commit 61fccb2d ("ravb: Add tx and rx clock internal delays mode
of APSR") the EthernetAVB driver enables tx and rx clock internal delay
modes (TDM and RDM) depending on the phy mode as follows:

    phy mode   | ASPR delay mode
    -----------+----------------
    rgmii-id   | TDM and RDM
    rgmii-rxid | RDM
    rgmii-txid | TDM

And prior to the above commit no internal delay mode settings were
implemented for any phy mode.

With this and the above change present tx internal delay mode is enabled
which has been observed to address failures in the case of 1Gbps
communication using the by salvator-x board with the KSZ9031RNX phy. This
has been reported to occur with both the r8a7795 (H3) and r8a7796 (M3-W)
SoCs.

With the above patch present but this patch present tx and rx internal
delay modes are enabled; and with the above patch and this present absent
no internal delay modes are enabled. In both cases failures have been
observed when using 1Gbps communication in the environments described
above.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch adds memory region:

  - After changes, the H3ULCB board has the following map:
    Bank0: 1GiB RAM : 0x000048000000 -> 0x0007fffffff
    Bank1: 1GiB RAM : 0x000500000000 -> 0x0053fffffff
    Bank2: 1GiB RAM : 0x000600000000 -> 0x0063fffffff
    Bank3: 1GiB RAM : 0x000700000000 -> 0x0073fffffff

  - Before changes, the old map looked like this:
    Bank0: 1GiB RAM : 0x000048000000 -> 0x0007fffffff
Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch enables I2C for DVFS device for for Salvator-X board on
R8A7795 SoC.
Signed-off-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

This patch adds I2C for DVFS device support for R8A7795 SoC.
Signed-off-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: Dien Pham <dien.pham.ry@rvc.renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

This patch adds support of I2C for DVFS device for Salvator-X board on
R8A7796 SoC.
Signed-off-by: Dien Pham <dien.pham.ry@rvc.renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

This patch adds I2C for DVFS device node for R8A7796 SoC.
Signed-off-by: Dien Pham <dien.pham.ry@rvc.renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

Pull networking fixes from David Miller:

 1) Fix double-free in batman-adv, from Sven Eckelmann.

 2) Fix packet stats for fast-RX path, from Joannes Berg.

 3) Netfilter's ip_route_me_harder() doesn't handle request sockets
    properly, fix from Florian Westphal.

 4) Fix sendmsg deadlock in rxrpc, from David Howells.

 5) Add missing RCU locking to transport hashtable scan, from Xin Long.

 6) Fix potential packet loss in mlxsw driver, from Ido Schimmel.

 7) Fix race in NAPI handling between poll handlers and busy polling,
    from Eric Dumazet.

 8) TX path in vxlan and geneve need proper RCU locking, from Jakub
    Kicinski.

 9) SYN processing in DCCP and TCP need to disable BH, from Eric
    Dumazet.

10) Properly handle net_enable_timestamp() being invoked from IRQ
    context, also from Eric Dumazet.

11) Fix crash on device-tree systems in xgene driver, from Alban Bedel.

12) Do not call sk_free() on a locked socket, from Arnaldo Carvalho de
    Melo.

13) Fix use-after-free in netvsc driver, from Dexuan Cui.

14) Fix max MTU setting in bonding driver, from WANG Cong.

15) xen-netback hash table can be allocated from softirq context, so use
    GFP_ATOMIC. From Anoob Soman.

16) Fix MAC address change bug in bgmac driver, from Hari Vyas.

17) strparser needs to destroy strp_wq on module exit, from WANG Cong.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (69 commits)
  strparser: destroy workqueue on module exit
  sfc: fix IPID endianness in TSOv2
  sfc: avoid max() in array size
  rds: remove unnecessary returned value check
  rxrpc: Fix potential NULL-pointer exception
  nfp: correct DMA direction in XDP DMA sync
  nfp: don't tell FW about the reserved buffer space
  net: ethernet: bgmac: mac address change bug
  net: ethernet: bgmac: init sequence bug
  xen-netback: don't vfree() queues under spinlock
  xen-netback: keep a local pointer for vif in backend_disconnect()
  netfilter: nf_tables: don't call nfnetlink_set_err() if nfnetlink_send() fails
  netfilter: nft_set_rbtree: incorrect assumption on lower interval lookups
  netfilter: nf_conntrack_sip: fix wrong memory initialisation
  can: flexcan: fix typo in comment
  can: usb_8dev: Fix memory leak of priv->cmd_msg_buffer
  can: gs_usb: fix coding style
  can: gs_usb: Don't use stack memory for USB transfers
  ixgbe: Limit use of 2K buffers on architectures with 256B or larger cache lines
  ixgbe: update the rss key on h/w, when ethtool ask for it
  ...

Pull more KVM updates from Radim Krčmář:
 "Second batch of KVM changes for the 4.11 merge window:

  PPC:
   - correct assumption about ASDR on POWER9
   - fix MMIO emulation on POWER9

  x86:
   - add a simple test for ioperm
   - cleanup TSS (going through KVM tree as the whole undertaking was
     caused by VMX's use of TSS)
   - fix nVMX interrupt delivery
   - fix some performance counters in the guest

  ... and two cleanup patches"

* tag 'kvm-4.11-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: nVMX: Fix pending events injection
  x86/kvm/vmx: remove unused variable in segment_base()
  selftests/x86: Add a basic selftest for ioperm
  x86/asm: Tidy up TSS limit code
  kvm: convert kvm.users_count from atomic_t to refcount_t
  KVM: x86: never specify a sample period for virtualized in_tx_cp counters
  KVM: PPC: Book3S HV: Don't use ASDR for real-mode HPT faults on POWER9
  KVM: PPC: Book3S HV: Fix software walk of guest process page tables

Pull documentation fixes from Jonathan Corbet:
 "A few fixes for the docs tree, including one for a 4.11 build
  regression"

* tag 'docs-4.11-fixes' of git://git.lwn.net/linux:
  Documentation/sphinx: fix primary_domain configuration
  docs: Fix htmldocs build failure
  doc/ko_KR/memory-barriers: Update control-dependencies section
  pcieaer doc: update the link
  Documentation: Update path to sysrq.txt

Pull staging/IIO driver fixes from Greg KH:
 "Here are a few small staging and IIO driver fixes for issues that
  showed up after the big set if changes you merged last week.

  Nothing major, just small bugs resolved in some IIO drivers, a lustre
  allocation fix, and some RaspberryPi driver fixes for reported
  problems, as well as a MAINTAINERS entry update.

  All of these have been in linux-next for a week with no reported
  issues"

* tag 'staging-4.11-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: fsl-mc: fix warning in DT ranges parser
  MAINTAINERS: Remove Noralf Trønnes as fbtft maintainer
  staging: vchiq_2835_arm: Make cache-line-size a required DT property
  staging: bcm2835/mmal-vchiq: unlock on error in buffer_from_host()
  staging/lustre/lnet: Fix allocation size for sv_cpt_data
  iio: adc: xilinx: Fix error handling
  iio: 104-quad-8: Fix off-by-one error when addressing flag register
  iio: adc: handle unknow of_device_id data

Pull crypto fixes from Herbert Xu:

 - vmalloc stack regression in CCM

 - Build problem in CRC32 on ARM

 - Memory leak in cavium

 - Missing Kconfig dependencies in atmel and mediatek

 - XTS Regression on some platforms (s390 and ppc)

 - Memory overrun in CCM test vector

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: vmx - Use skcipher for xts fallback
  crypto: vmx - Use skcipher for cbc fallback
  crypto: testmgr - Pad aes_ccm_enc_tv_template vector
  crypto: arm/crc32 - add build time test for CRC instruction support
  crypto: arm/crc32 - fix build error with outdated binutils
  crypto: ccm - move cbcmac input off the stack
  crypto: xts - Propagate NEED_FALLBACK bit
  crypto: api - Add crypto_requires_off helper
  crypto: atmel - CRYPTO_DEV_MEDIATEK should depend on HAS_DMA
  crypto: atmel - CRYPTO_DEV_ATMEL_TDES and CRYPTO_DEV_ATMEL_SHA should depend on HAS_DMA
  crypto: cavium - fix leak on curr if curr->head fails to be allocated
  crypto: cavium - Fix couple of static checker errors

Pull misc final vfs updates from Al Viro:
 "A few unrelated patches that got beating in -next.

  Everything else will have to go into the next window ;-/"

* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  hfs: fix hfs_readdir()
  selftest for default_file_splice_read() infoleak
  9p: constify ->d_name handling

Pull more SCSI updates from James Bottomley:
 "This is the set of stuff that didn't quite make the initial pull and a
  set of fixes for stuff which did.

  The new stuff is basically lpfc (nvme), qedi and aacraid. The fixes
  cover a lot of previously submitted stuff, the most important of which
  probably covers some of the failing irq vectors allocation and other
  fallout from having the SCSI command allocated as part of the block
  allocation functions"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (59 commits)
  scsi: qedi: Fix memory leak in tmf response processing.
  scsi: aacraid: remove redundant zero check on ret
  scsi: lpfc: use proper format string for dma_addr_t
  scsi: lpfc: use div_u64 for 64-bit division
  scsi: mac_scsi: Fix MAC_SCSI=m option when SCSI=m
  scsi: cciss: correct check map error.
  scsi: qla2xxx: fix spelling mistake: "seperator" -> "separator"
  scsi: aacraid: Fixed expander hotplug for SMART family
  scsi: mpt3sas: switch to pci_alloc_irq_vectors
  scsi: qedf: fixup compilation warning about atomic_t usage
  scsi: remove scsi_execute_req_flags
  scsi: merge __scsi_execute into scsi_execute
  scsi: simplify scsi_execute_req_flags
  scsi: make the sense header argument to scsi_test_unit_ready mandatory
  scsi: sd: improve TUR handling in sd_check_events
  scsi: always zero sshdr in scsi_normalize_sense
  scsi: scsi_dh_emc: return success in clariion_std_inquiry()
  scsi: fix memory leak of sdpk on when gd fails to allocate
  scsi: sd: make sd_devt_release() static
  scsi: qedf: Add QLogic FastLinQ offload FCoE driver framework.
  ...

Fixes: 43a0c675 ("strparser: Stream parser for messages")
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains Netfilter fixes for your net tree,
they are:

1) Missing check for full sock in ip_route_me_harder(), from
   Florian Westphal.

2) Incorrect sip helper structure initilization that breaks it when
   several ports are used, from Christophe Leroy.

3) Fix incorrect assumption when looking up for matching with adjacent
   intervals in the nft_set_rbtree.

4) Fix broken netlink event error reporting in nf_tables that results
   in misleading ESRCH errors propagated to userspace listeners.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull libnvdimm fixes from Dan Williams:
 "A fix and regression test case for nvdimm namespace label
  compatibility.

  Details:

   - An "nvdimm namespace label" is metadata on an nvdimm that
     provisions dimm capacity into a "namespace" that can host a block
     device / dax-filesytem, or a device-dax character device.

     A namespace is an object that other operating environment and
     platform firmware needs to comprehend for capabilities like booting
     from an nvdimm.

     The label metadata contains a checksum that Linux was not
     calculating correctly leading to other environments rejecting the
     Linux label.

   These have received a build success notification from the kbuild
   robot, and a positive test result from Nick who reported the problem"

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  nfit, libnvdimm: fix interleave set cookie calculation
  tools/testing/nvdimm: make iset cookie predictable

Pull PCI fixes from Bjorn Helgaas:

 - fix NULL pointer dereferences in many DesignWare-based drivers due to
   refactoring error

 - fix Altera config write breakage due to my refactoring error

* tag 'pci-v4.11-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: altera: Fix TLP_CFG_DW0 for TLP write
  PCI: dwc: Fix crashes seen due to missing assignments

Pull parisc fixes and cleanups from Helge Deller:
 "Nothing really important in this patchset: fix resource leaks in error
  paths, coding style cleanups and code removal"

* 'parisc-4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Remove flush_user_dcache_range and flush_user_icache_range
  parisc: fix a printk
  parisc: ccio-dma: Handle return NULL error from ioremap_nocache
  parisc: Define access_ok() as macro
  parisc: eisa: Fix resource leaks in error paths
  parisc: eisa: Remove coding style errors