Merge tag 'sunxi-dt-h5-for-4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt64

Allwinner H5 DT changes for 4.13

Just like the H3, this is mostly about enabling the EMAC on the H5, and
also has a new board, the Orange Pi Zero Plus 2

* tag 'sunxi-dt-h5-for-4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  arm64: allwinner: h5: Add initial Orangepi Zero Plus 2 support
  arm64: allwinner: h5: enable dwmac-sun8i for Nano Pi NEO2
  arm64: allwinner: h5: enable dwmac-sun8i for Orange Pi Prime
  arm64: allwinner: h5: sort the device nodes in / part for some boards
  arm64: allwinner: h5: add support for NanoPi NEO2 board
  arm64: allwinner: h5: add support for Orange Pi Prime board
  arm64: allwinner: orangepi-pc2: Enable dwmac-sun8i
  arm: sun8i: sunxi-h3-h5: add dwmac-sun8i ethernet driver
  arm: sun8i: sunxi-h3-h5: Add dt node for the syscon control module
  ARM: sunxi: h3-h5: Convert R_CCU raw numbers to macros
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'sunxi-dt64-for-4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt64

Allwinner arm64 DT changes for 4.13

Our usual arm64 changes. The most notable things are the EMAC support and
USB support enhancements. There's also support for the SoPine SoM, and the
OrangePi Win.

* tag 'sunxi-dt64-for-4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  arm64: allwinner: a64: Add initial Orangepi Win/WinPlus support
  arm64: allwinner: a64: add device tree for SoPine with baseboard
  arm64: allwinner: bananapi-m64: Enable dwmac-sun8i
  arm64: allwinner: pine64-plus: Enable dwmac-sun8i
  arm64: allwinner: pine64: Enable dwmac-sun8i
  arm64: allwinner: sun50i-a64: add dwmac-sun8i Ethernet driver
  arm64: allwinner: sun50i-a64: Add dt node for the syscon control module
  arm64: allwinner: a64: add DTSI file for SoPine SoM
  arm64: allwinner: a64: Convert CCU raw number references to macros
  arm64: dts: allwinner: pine64: Prepare optional UART nodes with pinctrl
  arm64: allwinner: a64: enable RSB on A64
  arm64: dts: allwinner: pine64: Add remaining UART aliases
  arm64: dts: allwinner: a64: Add UART2 pin nodes
  arm64: allwinner: a64: enable EHCI0/OHCI0 for Pine64
  arm64: allwinner: a64: add EHCI0/OHCI0 nodes to A64 DTSI
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'amlogic-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt64

Amlogic 64-bit DT changes for v4.13
- cleanup/reorganize alphabetically to better avoid conflicts
- add HDMI and CVBS nodes for multiple boards
- new pinctrl pins: SPI, HDMI CEC
- SCPI: fix thermal sensor reporting

New board support
- NanoPi K2 (GXBB)
- R-Box Pro (GXM)

* tag 'amlogic-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic: (36 commits)
  ARM64: dts: meson-gxl-s905x-p212: Add HDMI and CVBS nodes
  ARM64: dts: meson-gxl-s905x-khadas-vim: Add HDMI nodes
  ARM64: dts: meson-gxl-s905d-p230: Add HDMI nodes
  ARM64: dts: meson-gxbb-wetek-play2: Add HDMI and CVBS Nodes
  ARM64: dts: meson-gx: Fix sensors reporting from SCP
  ARM64: dts: meson-gxl: Add SPI pinctrl nodes
  ARM64: dts: meson-gxbb: Add SPI pinctrl nodes
  ARM64: dts: meson-gxl: Add Ethernet PHY LEDS pins nodes
  ARM64: dts: meson-gxl: Add CEC pins nodes
  ARM64: dts: meson-gxbb: Add CEC pins nodes
  ARM64: dts: Fix GXBB periphs pinctrl pull-enable register base
  ARM64: dts: Fix GXL periphs pinctrl pull-enable register base
  ARM64: dts: meson-gxl: Fix pinctrl periphs gpio-ranges
  arm64: dts: amlogic: Add NanoPi K2
  dt-bindings: arm: amlogic: Add NanoPi K2
  arm64: dts: meson-gxm: Add R-Box Pro
  dt-bindings: arm: amlogic: Add R-Box Pro
  dt-bindings: Add Kingnovel vendor prefix
  arm64: dts: meson-gx-p23x-q20x: Fix node order
  arm64: dts: meson-gxm-nexbox-a1: Fix node order
  ...
Signed-off-by: Olof Johansson <olof@lixom.net>

This pull request contains Broadcom ARM64-based SoCs Device Tree changes for
4.13. Please note the following from Eric:

I've based this summary on the bcm2835-dt-next tag, to clarify what's in this
patch series, but it does require being careful since it involves a cross-merge
between branches.

- Anup documents the Broadcom Stingray binding, common clocks, adds initial
  support for the Stingray DTSI and DTS files and adds support for the PL022,
  PL330 and SP805

- Sandeep adds the clock nodes to the Stingray Device Tree nodes

- Pramod adds support for the NAND, pinctrl, GPIO to the Stingray Device Tree nodes

- Oza adds I2C Device Tree nodes to the Stingray DTSes

- Srinath adds PWM and SDHCI Device Tree nodes for the Stingray SoC

- Ravijeta adds support for the USB Dual Role PHY on Northstar 2

- Gerd starts adding references to the sdhost and sdhci controllers, and then
  switches the sdcard to to use the SDHOST (faster than SDHCI)

- Stefan defines the BCM2837 thermal coefficients in order for the Raspberry Pi
  thermal driver to work correctly

* tag 'arm-soc/for-4.13/devicetree-arm64' of http://github.com/Broadcom/stblinux:
  arm64: dts: NS2: Add USB DRD PHY device tree node
  ARM64: dts: bcm2837: Define CPU thermal coefficients
  arm64: dts: Add PWM and SDHCI DT nodes for Stingray SOC
  arm64: dts: Add PL022, PL330 and SP805 DT nodes for Stingray
  arm64: dts: Add I2C DT nodes for Stingray SoC
  arm64: dts: Add GPIO DT nodes for Stingray SOC
  arm64: dts: Add pinctrl DT nodes for Stingray SOC
  arm64: dts: Add NAND DT nodes for Stingray SOC
  arm64: dts: Add clock DT nodes for Stingray SOC
  arm64: dts: Initial DTS files for Broadcom Stingray SOC
  dt-bindings: clk: Extend binding doc for Stingray SOC
  dt-bindings: bcm: Add Broadcom Stingray bindings document
  ARM: dts: bcm283x: switch from &sdhci to &sdhost
  arm64: dts: bcm2837: add &sdhci and &sdhost
  ARM: dts: bcm283x: Add CPU thermal zone with 1 trip point
  ARM: dts: Add devicetree for the Raspberry Pi 3, for arm32 (v6)
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'uniphier-dt64-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into next/dt64

UniPhier ARM64 SoC DT updates for v4.13

- specify timing delay properties of eMMC
- fix W=1 build warnings
- increase memory reserve size
- use SPDX License Identifier
- add new board support (LD11/LD20 global)

* tag 'uniphier-dt64-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
  arm64: dts: uniphier: add support for LD20 Global board
  arm64: dts: uniphier: add support for LD11 Global board
  arm64: dts: uniphier: use SPDX-License-Identifier
  arm64: dts: uniphier: reserve more memory for LD11/LD20
  arm64: dts: uniphier: fix simple-bus unit address format error
  arm64: dts: uniphier: Use - instead of @ for DT OPP entries
  arm64: dts: uniphier: add cdns, phy-dll-delay-sdclk(-hsmmc) for eMMC
  arm64: dts: uniphier: add input-delay properties to Cadence eMMC node
Signed-off-by: Olof Johansson <olof@lixom.net>

Add device tree nodes for
mt8173:
- split USB SuperSpeed port in HighSpeed and SuperSpeed ports.
- move USB phy clocks up in hierarchy to met new bindings description
- move MDP nodes up in hierarchy to met new bindings description

mt6797:
- add basic SoC support
- add clock driver
- add power domain

dt-bindings:
- clean-up i2c binding description
- add binding for mt2701 i2c node
- add fallback compatible to scpsys binding description
- add bindings description for mt7622 and mt6796

* tag 'v4.12-next-dts64' of https://github.com/mbgg/linux-mediatek:
  dt-bindings: mediatek: add bindings for MediaTek MT7622 SoC
  arm64: dts: mt8173: Fix mdp device tree
  dt-bindings: i2c: Add Mediatek MT2701 i2c binding
  dt-bindings: i2c-mtk: Add mt7623 binding
  dt-bindings: i2c-mtk: Delete bindings
  dt-bindings: i2c-mt6577: Rename file to reflect bindings
  dt-bindings: mtk-sysirq: Correct bindings for supported SoCs
  arm64: dts: mediatek: add clk and scp nodes for MT6797
  dt-bindings: mediatek: add MT6797 power dt-bindings
  arm64: dts: mediatek: add mt6797 support
  dt-bindings: mediatek: Add bindings for mediatek MT6797 Platform
  arm64: dts: mt8173: move clock from phy node into port nodes
  arm64: dts: mt8173: split usb SuperSpeed port into two ports
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'samsung-dt64-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt64

Samsung DeviceTree ARM64 update for v4.13:
1. Remove unneeded TE interrupt gpio property.

* tag 'samsung-dt64-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
  arm64: dts: exynos: Remove the te-gpios property in the TM2 boards
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'v4.13-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt64

Support for the new rk3399 firefly board; extending the pcie ranges to
make usage of pci switches possible; some more qos and pinctrl nodes on
rk3399; updates for the rk3399 cpu operating points including separate
opps for the higher rates OP1 variant of the chip and mmc-nodes for
the rk3328.

* tag 'v4.13-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  arm64: dts: rockchip: update common rk3399 operating points
  arm64: dts: rockchip: introduce rk3399-op1 operating points
  arm64: dts: rockchip: enable usb3 controllers on rk3399-firefly
  arm64: dts: rockchip: add ethernet0 alias on rk3399
  arm64: dts: rockchip: bring rk3399-firefly power-tree in line
  arm64: dts: rockchip: add sdmmc/sdio/emmc nodes for RK3328 SoCs
  arm64: dts: rockchip: extent IORESOURCE_MEM_64 of PCIe for rk3399
  arm64: dts: rockchip: extent bus-ranges of PCIe for rk3399
  arm64: dts: rockchip: add pinctrl settings for some rk3399 peripherals
  arm64: dts: rockchip: add some missing qos nodes on rk3399
  arm64: dts: rockchip: add support for firefly-rk3399 board
  dt-bindings: add firefly-rk3399 board support
Signed-off-by: Olof Johansson <olof@lixom.net>

This pull request brings in the switch to sdhost for MMC on RPi3
(improving storage performance and leaving sdhci for wireless), and
the correct CPU thermal coefficients.

The thermal changes required a merge from bcm2835-dt-next, where the
nodes were added.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Orangepi Zero Plus 2 is an open-source single-board computer
using the Allwinner h5 SOC.

H5 Orangepi Zero Plus 2 has
- Quad-core Cortex-A53
- 512MB DDR3
- micrSD slot and 8GB eMMC
- Debug TTL UART
- HDMI
- Wifi + BT
- OTG+power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Orangepi Win/WinPlus is an open-source single-board computer
using the Allwinner A64 SOC.

A64 Orangepi Win/WinPlus has
- A64 Quad-core Cortex-A53 64bit
- 1GB(Win)/2GB(Win Plus) DDR3 SDRAM
- Debug TTL UART
- Four USB 2.0
- HDMI
- LCD
- Audio and MIC
- Wifi + BT
- IR receiver
- 5V DC power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add initial device tree support for LD20 Global board.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Add initial device tree support for LD11 Global board.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Add HDMI and CVBS nodes for the Amlogic P212 reference board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

Add HDMI nodes for the Khadas Vim board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

Add HDMI nodes for the Amlogic P230 board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

Add HDMI and CVBS nodes for the Wetek Play2 board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

This patch adds device tree node for USB Dual Role Device PHY for
Broadcom's Northstar2 SoC.
Signed-off-by: Raviteja Garimella <raviteja.garimella@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

This defines the bcm2837 SoC specific thermal coefficients in
order to initialize the thermal driver correctly.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Eduardo Valentin <edubezval@gmail.com>

This merge brings in the cpu-thermal node we in bcm283x that we need
in order to set the rpi3's coefficients.

This adds dt-binding documentation for MediaTek MT7622 SoC
which currently only includes basic items such as ARM CPU,
MediaTek SYSIRQ and UART.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>

If the mdp_* nodes are under an mdp sub-node, their corresponding
platform device does not automatically get its iommu assigned properly.

Fix this by moving the mdp component nodes up a level such that they are
siblings of mdp and all other SoC subsystems.  This also simplifies the
device tree.

Although it fixes iommu assignment issue, it also break compatibility
with old device tree. So, the patch in driver is needed to iterate over
sibling mdp device nodes, not child ones, to keep driver work properly.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Minghsiu Tsai <minghsiu.tsai@mediatek.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>

Add MT2701 i2c binding to i2c-mt6577.txt and there is no need to
modify i2c driver.
Signed-off-by: Jun Gao <jun.gao@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>

The mt7623 dtsi has support for the i2c block, but this is not documented.
Add the documentation for SoC mt7623 to de description.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>

The bindings file list bindings for mt1827 and mt8135 but
these bindings are not supported by the driver. Remove the bindings.
Also do some minor style changes to the compatible documentation
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>

The i2c-mt6577.txt actually holds the bindings for all mediatek supported i2c
controller. Change the name to i2c.mtk.txt to reflect that.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>

Follow the recent trend for the license description, and fix the wrongly
stated X11 to MIT.

The X11 license text [1] is explicitly for the X Consortium and has a
couple of extra clauses.  The MIT license text [2] is actually what the
current DT files claim.

[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.htmlSigned-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Reserve enough space below the kernel base.
The assumed address map is:
  80000000 - 80ffffff : for IPP
  81000000 - 81ffffff : for ARM secure
  82000000 -          : for Linux
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Add the required DT parts to enable Ethernet (dwmac-sun8i driver) on
the Nano Pi NEO2 board. It uses an external Realtek RTL8211E PHY
connected via RGMII to provide GbE network. Specially unlike other
Allwinner boards, the phy is connected to MDIO address 7, not 1.

This includes the regulator (which is controlled by a GPIO pin) and
the actual Ethernet MAC node, referring the RGMII pins of the device.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add the required DT parts to enable Ethernet (dwmac-sun8i driver) on
the Orange Pi Prime board. It uses an external Realtek RTL8211E PHY
connected via RGMII to provide GbE network.

This includes the regulator (which is controlled by a GPIO pin) and
the actual Ethernet MAC node, referring the RGMII pins of the device.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The reg_vcc3v3 node is wrongly placed at the start of the / part, but
not with other fixed regulators used by the board, which makes the
device nodes unsorted.

As Orange Pi Prime and Nano Pi NEO2 device trees are copy'n'paste works,
they share the device node unsorted issue.

Fix this by move reg_vcc3v3 node to the position before reg_usb0_vbus.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Pine64 have made an official baseboard when SoPine SoM is out.

The official baseboard is like the original Pine64 -- but with SD card
slot replaced with Pine64's eMMC module slot.

Add a device tree for SoPine with the baseboard.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The dwmac-sun8i  hardware is present on the BananaPi M64.
It uses an external PHY rtl8211e via RGMII.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The dwmac-sun8i hardware is present on the pine64 plus.
It uses an external PHY rtl8211e via RGMII.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The dwmac-sun8i hardware is present on the pine64
It uses an external PHY via RMII.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The dwmac-sun8i is an Ethernet MAC that supports 10/100/1000 Mbit
connections. It is very similar to the device found in the Allwinner
H3, but lacks the internal 100 Mbit PHY and its associated control
bits.
This adds the necessary bits to the Allwinner A64 SoC .dtsi, but keeps
it disabled at this level.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This patch add the dt node for the syscon register present on the
Allwinner A64.

Only two register are present in this syscon and the only one useful is
the one dedicated to EMAC clock.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

SoPine is a SoM by Pine64, which have a gold finger compatible with the
slot of DDR3 SODIMM (signals are not compatible), and have an A64, an
AXP803, a LPDDR3 DRAM chip, a power led and a MicroSD slot on it.

The card detect pin of the MicroSD slot on the SoM is pulled down, which
makes it unusable; however, the slot is at the surface of the SoM that
is closed to the baseboard, so it's nearly impossible to hot-swap it,
thus I make it non-removable.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The A64 device tree file has some remnants of raw number references
to the CCU node, likely from when the CCU bindings and device tree
changes were first merged.

Convert these, and the R_CCU ones, to use the proper defined macros
from their respective device tree binding header files.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Pine64 exposes all A64 UARTs, not just UART0.

Since the pins can be used as GPIO, don't enable the new UART nodes by
default, but prepare the pinctrl settings to aid in activating them via
overlays, i.e., overriding the status property of &uartX nodes.

For UART4 (Euler) the safer route of not including RTS/CTS pins is chosen,
whereas for UART1 (Bluetooth) they are included.

Add the corresponding pinctrl nodes where missing.
Suggested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>