Ensure that we supply the same phy interface mode to mac_link_down() as
we did for the corresponding mac_link_up() call.  This ensures that MAC
drivers that use the phy interface mode in these methods can depend on
mac_link_down() always corresponding to a mac_link_up() call for the
same interface mode.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

The sh_eth_close() resets the MAC and then calls phy_stop()
so that mdio read access result is incorrect without any error
according to kernel trace like below:

ifconfig-216   [003] .n..   109.133124: mdio_access: ee700000.ethernet-ffffffff read  phy:0x01 reg:0x00 val:0xffff

According to the hardware manual, the RMII mode should be set to 1
before operation the Ethernet MAC. However, the previous code was not
set to 1 after the driver issued the soft_reset in sh_eth_dev_exit()
so that the mdio read access result seemed incorrect. To fix the issue,
this patch adds a condition and set the RMII mode register in
sh_eth_dev_exit() for R-Car Gen2 and RZ/A1 SoCs.

Note that when I have tried to move the sh_eth_dev_exit() calling
after phy_stop() on sh_eth_close(), but it gets worse (kernel panic
happened and it seems that a register is accessed while the clock is
off).
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Both sysfs-bus-mdio and sysfs-class-net-phydev contain the same
duplication information. There is not currently any MDIO bus specific
attribute, but there are PHY device (struct phy_device) specific
attributes. Use the more precise description from sysfs-bus-mdio and
carry that over to sysfs-class-net-phydev.

Fixes: 86f22d04 ("net: sysfs: Document PHY device sysfs attributes")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

If llc_mac_hdr_init() returns an error, we must drop the skb
since no llc_build_and_send_ui_pkt() caller will take care of this.

BUG: memory leak
unreferenced object 0xffff8881202b6800 (size 2048):
  comm "syz-executor907", pid 7074, jiffies 4294943781 (age 8.590s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
    1a 00 07 40 00 00 00 00 00 00 00 00 00 00 00 00  ...@............
  backtrace:
    [<00000000e25b5abe>] kmemleak_alloc_recursive include/linux/kmemleak.h:55 [inline]
    [<00000000e25b5abe>] slab_post_alloc_hook mm/slab.h:439 [inline]
    [<00000000e25b5abe>] slab_alloc mm/slab.c:3326 [inline]
    [<00000000e25b5abe>] __do_kmalloc mm/slab.c:3658 [inline]
    [<00000000e25b5abe>] __kmalloc+0x161/0x2c0 mm/slab.c:3669
    [<00000000a1ae188a>] kmalloc include/linux/slab.h:552 [inline]
    [<00000000a1ae188a>] sk_prot_alloc+0xd6/0x170 net/core/sock.c:1608
    [<00000000ded25bbe>] sk_alloc+0x35/0x2f0 net/core/sock.c:1662
    [<000000002ecae075>] llc_sk_alloc+0x35/0x170 net/llc/llc_conn.c:950
    [<00000000551f7c47>] llc_ui_create+0x7b/0x140 net/llc/af_llc.c:173
    [<0000000029027f0e>] __sock_create+0x164/0x250 net/socket.c:1430
    [<000000008bdec225>] sock_create net/socket.c:1481 [inline]
    [<000000008bdec225>] __sys_socket+0x69/0x110 net/socket.c:1523
    [<00000000b6439228>] __do_sys_socket net/socket.c:1532 [inline]
    [<00000000b6439228>] __se_sys_socket net/socket.c:1530 [inline]
    [<00000000b6439228>] __x64_sys_socket+0x1e/0x30 net/socket.c:1530
    [<00000000cec820c1>] do_syscall_64+0x76/0x1a0 arch/x86/entry/common.c:301
    [<000000000c32554f>] entry_SYSCALL_64_after_hwframe+0x44/0xa9

BUG: memory leak
unreferenced object 0xffff88811d750d00 (size 224):
  comm "syz-executor907", pid 7074, jiffies 4294943781 (age 8.600s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
    00 f0 0c 24 81 88 ff ff 00 68 2b 20 81 88 ff ff  ...$.....h+ ....
  backtrace:
    [<0000000053026172>] kmemleak_alloc_recursive include/linux/kmemleak.h:55 [inline]
    [<0000000053026172>] slab_post_alloc_hook mm/slab.h:439 [inline]
    [<0000000053026172>] slab_alloc_node mm/slab.c:3269 [inline]
    [<0000000053026172>] kmem_cache_alloc_node+0x153/0x2a0 mm/slab.c:3579
    [<00000000fa8f3c30>] __alloc_skb+0x6e/0x210 net/core/skbuff.c:198
    [<00000000d96fdafb>] alloc_skb include/linux/skbuff.h:1058 [inline]
    [<00000000d96fdafb>] alloc_skb_with_frags+0x5f/0x250 net/core/skbuff.c:5327
    [<000000000a34a2e7>] sock_alloc_send_pskb+0x269/0x2a0 net/core/sock.c:2225
    [<00000000ee39999b>] sock_alloc_send_skb+0x32/0x40 net/core/sock.c:2242
    [<00000000e034d810>] llc_ui_sendmsg+0x10a/0x540 net/llc/af_llc.c:933
    [<00000000c0bc8445>] sock_sendmsg_nosec net/socket.c:652 [inline]
    [<00000000c0bc8445>] sock_sendmsg+0x54/0x70 net/socket.c:671
    [<000000003b687167>] __sys_sendto+0x148/0x1f0 net/socket.c:1964
    [<00000000922d78d9>] __do_sys_sendto net/socket.c:1976 [inline]
    [<00000000922d78d9>] __se_sys_sendto net/socket.c:1972 [inline]
    [<00000000922d78d9>] __x64_sys_sendto+0x2a/0x30 net/socket.c:1972
    [<00000000cec820c1>] do_syscall_64+0x76/0x1a0 arch/x86/entry/common.c:301
    [<000000000c32554f>] entry_SYSCALL_64_after_hwframe+0x44/0xa9

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the pmtu_vti6_link_change_mtu test, both local and remote addresses
for the vti6 tunnel are assigned to the same address given to the dummy
interface that we use as encapsulating device with a known MTU.

This works as long as the dummy interface is actually selected, via
rt6_lookup(), as encapsulating device. But if the remote address of the
tunnel is a local address too, the loopback interface could also be
selected, and there's nothing wrong with it.

This is what some older -stable kernels do (3.18.z, at least), and
nothing prevents us from subtly changing FIB implementation to revert
back to that behaviour in the future.

Define an IPv6 prefix instead, and use two separate addresses as local
and remote for vti6, so that the encapsulating device can't be a
loopback interface.
Reported-by: Xiumei Mu <xmu@redhat.com>
Fixes: 1fad59ea ("selftests: pmtu: Add pmtu_vti6_link_change_mtu test")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure only the portals for the online CPUs are used.
Without this change, there are issues when someone boots with
maxcpus=n, with n < actual number of cores available as frames
either received or corresponding to the transmit confirmation
path would be offered for dequeue to the offline CPU portals,
getting lost.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix below issues in err code path of probe:
1. we don't need to unregister_netdev() because the netdev isn't
registered.
2. when register_netdev() fails, we also need to destroy bm pool for
HWBM case.

Fixes: dc35a10f ("net: mvneta: bm: add support for hardware buffer management")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the subdriver defers probe, do not show an error message. It's
perfectly fine for this error to occur since the driver will get another
chance to probe after some time and will usually succeed after all of
the resources that it requires have been registered.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Igor Russkikh says:

====================
net: aquantia: various fixes May, 2019

Here is a set of various bug fixes found on recent verification stage.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Thats a known quirk in windows tcp stack it can produce 0xffff checksum.
Thats incorrect but it is.

Atlantic HW with LRO enabled handles that incorrectly and changes csum to
0xfffe - but indicates that csum is invalid. This causes driver to pass
packet to linux networking stack with CSUM_NONE, stack eventually drops
the packet.

There is a quirk in atlantic HW to enable correct processing of
0xffff incorrect csum. Enable it.

The visible bug is that windows link partner with software generated csums
caused TCP connection to be unstable since all packets that csum value
are dropped.
Reported-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Driver stops producing skbs on ring if a packet with FCS error
was coalesced into LRO session. Ring gets hang forever.

Thats a logical error in driver processing descriptors:
When rx_stat indicates MAC Error, next pointer and eop flags
are not filled. This confuses driver so it waits for descriptor 0
to be filled by HW.

Solution is fill next pointer and eop flag even for packets with FCS error.

Fixes: bab6de8f ("net: ethernet: aquantia: Atlantic A0 and B0 specific functions.")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Atlantic hardware does not aggregate nor breaks LRO sessions
with bad csum packets. This means driver should take care of that.

If in LRO session there is a non-first descriptor with invalid
checksum (L2/L3/L4), the driver must account this information
in csum application logic.

Fixes: 018423e9 ("net: ethernet: aquantia: Add ring support code")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case no other traffic happening on the ring, full tx cleanup
may not be completed. That may cause socket buffer to overflow
and tx traffic to stuck until next activity on the ring happens.

This is due to logic error in budget variable decrementor.
Variable is compared with zero, and then post decremented,
causing it to become MAX_INT. Solution is remove decrementor
from the `for` statement and rewrite it in a clear way.

Fixes: b647d398 ("net: aquantia: Add tx clean budget and valid budget handling logic")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Building with Clang reports the redundant use of MODULE_DEVICE_TABLE():

drivers/net/ethernet/dec/tulip/de4x5.c:2110:1: error: redefinition of '__mod_eisa__de4x5_eisa_ids_device_table'
MODULE_DEVICE_TABLE(eisa, de4x5_eisa_ids);
^
./include/linux/module.h:229:21: note: expanded from macro 'MODULE_DEVICE_TABLE'
extern typeof(name) __mod_##type##__##name##_device_table               \
                    ^
<scratch space>:90:1: note: expanded from here
__mod_eisa__de4x5_eisa_ids_device_table
^
drivers/net/ethernet/dec/tulip/de4x5.c:2100:1: note: previous definition is here
MODULE_DEVICE_TABLE(eisa, de4x5_eisa_ids);
^
./include/linux/module.h:229:21: note: expanded from macro 'MODULE_DEVICE_TABLE'
extern typeof(name) __mod_##type##__##name##_device_table               \
                    ^
<scratch space>:85:1: note: expanded from here
__mod_eisa__de4x5_eisa_ids_device_table
^

This drops the one further from the table definition to match the common
use of MODULE_DEVICE_TABLE().

Fixes: 07563c71 ("EISA bus MODALIAS attributes support")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
net/tls: two fixes for rx_list pre-handling

tls_sw_recvmsg() had been modified to cater better to async decrypt.
Partially read records now live on the rx_list. Data is copied from
this list before the old do {} while loop, and the not included
correctly in deciding whether to sleep or not and lowat threshold
handling. These modifications, unfortunately, added some bugs.

First patch fixes lowat - we need to calculate the threshold early
and make sure all copied data is compared to the threshold, not just
the freshly decrypted data.

Third patch fixes sleep - if data is picked up from rx_list and
no flags are set, we should not put the process to sleep, but
rather return the partial read.

Patches 2 and 4 add test cases for these bugs, both will cause
a sleep and test timeout before the fix.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a test which sends 15 bytes of data, and then tries
to read 10 byes twice.  Previously the second read would
sleep indifinitely, since the record was already decrypted
and there is only 5 bytes left, not full 10.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When tls_sw_recvmsg() partially copies a record it pops that
record from ctx->recv_pkt and places it on rx_list.

Next iteration of tls_sw_recvmsg() reads from rx_list via
process_rx_list() before it enters the decryption loop.
If there is no more records to be read tls_wait_data()
will put the process on the wait queue and got to sleep.
This is incorrect, because some data was already copied
in process_rx_list().

In case of RPC connections process may never get woken up,
because peer also simply blocks in read().

I think this may also fix a similar issue when BPF is at
play, because after __tcp_bpf_recvmsg() returns some data
we subtract it from len and use continue to restart the
loop, but len could have just reached 0, so again we'd
sleep unnecessarily. That's added by:
commit d3b18ad3 ("tls: add bpf support to sk_msg handling")

Fixes: 692d7b5d ("tls: Fix recvmsg() to be able to peek across multiple records")
Reported-by: David Beckett <david.beckett@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Tested-by: David Beckett <david.beckett@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Set SO_RCVLOWAT and test it gets respected when gathering
data from multiple records.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If some of the data came from the previous record, i.e. from
the rx_list it had already been decrypted, so it's not counted
towards the "decrypted" variable, but the "copied" variable.
Take that into account when checking lowat.

When calculating lowat target we need to pass the original len.
E.g. if lowat is at 80, len is 100 and we had 30 bytes on rx_list
target would currently be incorrectly calculated as 70, even though
we only need 50 more bytes to make up the 80.

Fixes: 692d7b5d ("tls: Fix recvmsg() to be able to peek across multiple records")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Tested-by: David Beckett <david.beckett@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ioana Radulescu says:

====================
dpaa2-eth: Fix smatch warnings

Fix a couple of warnings reported by smatch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Function dpaa2_eth_cls_key_size() expects a 64bit argument,
but DPAA2_ETH_DIST_ALL is defined as UINT_MAX. Fix this.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use PTR_ERR_OR_ZERO instead of PTR_ERR in cases where
zero is a valid input. Reported by smatch.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Smatch reports a potential spectre vulnerability in the dpaa2-eth
driver, where the value of rxnfc->fs.location (which is provided
from user-space) is used as index in an array.

Add a call to array_index_nospec() to sanitize the access.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Once in a while, with just the right timing, 802.3ad slaves will fail to
properly initialize, winding up in a weird state, with a partner system
mac address of 00:00:00:00:00:00. This started happening after a fix to
properly track link_failure_count tracking, where an 802.3ad slave that
reported itself as link up in the miimon code, but wasn't able to get a
valid speed/duplex, started getting set to BOND_LINK_FAIL instead of
BOND_LINK_DOWN. That was the proper thing to do for the general "my link
went down" case, but has created a link initialization race that can put
the interface in this odd state.

The simple fix is to instead set the slave link to BOND_LINK_DOWN again,
if the link has never been up (last_link_up == 0), so the link state
doesn't bounce from BOND_LINK_DOWN to BOND_LINK_FAIL -- it hasn't failed
in this case, it simply hasn't been up yet, and this prevents the
unnecessary state change from DOWN to FAIL and getting stuck in an init
failure w/o a partner mac.

Fixes: ea53abfa ("bonding/802.3ad: fix link_failure_count tracking")
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
CC: netdev@vger.kernel.org
Tested-by: Heesoon Kim <Heesoon.Kim@stratus.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethtool ops get_rxfh_context and set_rxfh_context are used to create,
remove and access parameters associated to RSS contexts, in a similar
fashion to get_rxfh and set_rxfh.

Add a small descritopn of these callbacks in the struct ethtool_ops doc.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Biao Huang says:

====================
fix some bugs in stmmac

changes in v4:
        since MTL_OPERATION_MODE write back issue has be fixed in the latest driver,
remove original patch#3

changes in v3:
        add a Fixes:tag for each patch

changes in v2:
        1. update rx_tail_addr as Jose's comment
        2. changes clk_csr condition as Alex's proposition
        3. remove init lines in dwmac-mediatek, get clk_csr from dts instead.

v1:
This series fix some bugs in stmmac driver
3 patches are for common stmmac or dwmac4:
        1. update rx tail pointer to fix rx dma hang issue.
        2. change condition for mdc clock to fix csr_clk can't be zero issue.
        3. write the modified value back to MTL_OPERATION_MODE.
1 patch is for dwmac-mediatek:
        modify csr_clk value to fix mdio read/write fail issue for dwmac-mediatek
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

1. the frequency of csr clock is 66.5MHz, so the csr_clk value should
be 0 other than 5.
2. the csr_clk can be got from device tree, so remove initialization here.

Fixes: 9992f37e ("stmmac: dwmac-mediatek: add support for mt2712")
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The specific clk_csr value can be zero, and
stmmac_clk is necessary for MDC clock which can be set dynamically.
So, change the condition from plat->clk_csr to plat->stmmac_clk to
fix clk_csr can't be zero issue.

Fixes: cd7201f4 ("stmmac: MDC clock dynamically based on the csr clock input")
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently we will not update the receive descriptor tail pointer in
stmmac_rx_refill. Rx dma will think no available descriptors and stop
once received packets exceed DMA_RX_SIZE, so that the rx only test will fail.

Update the receive tail pointer in stmmac_rx_refill to add more descriptors
to the rx channel, so packets can be received continually

Fixes: 54139cf3 ("net: stmmac: adding multiple buffers for rx")
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In function ip_ra_control(), the pointer new_ra is allocated a memory
space via kmalloc(). And it is used in the following codes. However,
when  there is a memory allocation error, kmalloc() fails. Thus null
pointer dereference may happen. And it will cause the kernel to crash.
Therefore, we should check the return value and handle the error.
Signed-off-by: Gen Zhang <blackgod016574@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In function ip6_ra_control(), the pointer new_ra is allocated a memory
space via kmalloc(). And it is used in the following codes. However,
when there is a memory allocation error, kmalloc() fails. Thus null
pointer dereference may happen. And it will cause the kernel to crash.
Therefore, we should check the return value and handle the error.
Signed-off-by: Gen Zhang <blackgod016574@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Function tcf_action_dump() relies on tc_action->order field when starting
nested nla to send action data to userspace. This approach breaks in
several cases:

- When multiple filters point to same shared action, tc_action->order field
  is overwritten each time it is attached to filter. This causes filter
  dump to output action with incorrect attribute for all filters that have
  the action in different position (different order) from the last set
  tc_action->order value.

- When action data is displayed using tc action API (RTM_GETACTION), action
  order is overwritten by tca_action_gd() according to its position in
  resulting array of nl attributes, which will break filter dump for all
  filters attached to that shared action that expect it to have different
  order value.

Don't rely on tc_action->order when dumping actions. Set nla according to
action position in resulting array of actions instead.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 2391b003 which has
introduced regression. Now SGE's BAR2 Doorbell/GTS Page Size is
interpreted correctly in the firmware itself by using actual host
page size. Hence previous commit needs to be reverted.
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the clk mismatch in the error path "failed_reset" because
below error path will disable clk_ahb and clk_ipg directly, it
should use pm_runtime_put_noidle() instead of pm_runtime_put()
to avoid to call runtime resume callback.
Reported-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter/IPVS fixes for net

The following patchset contains Netfilter/IPVS fixes for your net tree:

1) Fix crash when dumping rules after conversion to RCU,
   from Florian Westphal.

2) Fix incorrect hook reinjection from nf_queue in case NF_REPEAT,
   from Jagdish Motwani.

3) Fix check for route existence in fib extension, from Phil Sutter.

4) Fix use after free in ip_vs_in() hook, from YueHaibing.

5) Check for veth existence from netfilter selftests,
   from Jeffrin Jose T.

6) Checksum corruption in UDP NAT helpers due to typo,
   from Florian Westphal.

7) Pass up packets to classic forwarding path regardless of
   IPv4 DF bit, patch for the flowtable infrastructure from Florian.

8) Set liberal TCP tracking for flows that are placed in the
   flowtable, in case they need to go back to classic forwarding path,
   also from Florian.

9) Don't add flow with sequence adjustment to flowtable, from Florian.

10) Skip IPv4 options from IPv6 datapath in flowtable, from Florian.

11) Add selftest for the flowtable infrastructure, from Florian.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

VLAN flows never get offloaded unless ivlan_vld is set in filter spec.
It's not compulsory for vlan_ethtype to be set.

So, always enable ivlan_vld bit for offloading VLAN flows regardless of
vlan_ethtype is set or not.

Fixes: ad9af3e0 (cxgb4: add tc flower match support for vlan)
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't prune the master node in the hsr_prune_nodes function.
Neither time_in[HSR_PT_SLAVE_A] nor time_in[HSR_PT_SLAVE_B]
will ever be updated by hsr_register_frame_in for the master port.
Thus, the master node will be repeatedly pruned leading to
repeated packet loss.
This bug never appeared because the hsr_prune_nodes function
was only called once. Since commit 5150b45f
("net: hsr: Fix node prune function for forget time expiry") this issue
is fixed unveiling the issue described above.

Fixes: 5150b45f ("net: hsr: Fix node prune function for forget time expiry")
Signed-off-by: Andreas Oetken <andreas.oetken@siemens.com>
Tested-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The flow_rule is only used when configuring the classification tables,
and should be free'd once we're done using it. The current code only
frees it in the error path.

Fixes: 90b509b3 ("net: mvpp2: cls: Add Classification offload support")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ip_sf_list_clear_all() needs to be defined even if !CONFIG_IP_MULTICAST

Fixes: 3580d04a ("ipv4/igmp: fix another memory leak in igmpv3_del_delrec()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

syzbot reported memory leaks [1] that I have back tracked to
a missing cleanup from igmpv3_del_delrec() when
(im->sfmode != MCAST_INCLUDE)

Add ip_sf_list_clear_all() and kfree_pmc() helpers to explicitely
handle the cleanups before freeing.

[1]

BUG: memory leak
unreferenced object 0xffff888123e32b00 (size 64):
  comm "softirq", pid 0, jiffies 4294942968 (age 8.010s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 e0 00 00 01 00 00 00 00  ................
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<000000006105011b>] kmemleak_alloc_recursive include/linux/kmemleak.h:55 [inline]
    [<000000006105011b>] slab_post_alloc_hook mm/slab.h:439 [inline]
    [<000000006105011b>] slab_alloc mm/slab.c:3326 [inline]
    [<000000006105011b>] kmem_cache_alloc_trace+0x13d/0x280 mm/slab.c:3553
    [<000000004bba8073>] kmalloc include/linux/slab.h:547 [inline]
    [<000000004bba8073>] kzalloc include/linux/slab.h:742 [inline]
    [<000000004bba8073>] ip_mc_add1_src net/ipv4/igmp.c:1961 [inline]
    [<000000004bba8073>] ip_mc_add_src+0x36b/0x400 net/ipv4/igmp.c:2085
    [<00000000a46a65a0>] ip_mc_msfilter+0x22d/0x310 net/ipv4/igmp.c:2475
    [<000000005956ca89>] do_ip_setsockopt.isra.0+0x1795/0x1930 net/ipv4/ip_sockglue.c:957
    [<00000000848e2d2f>] ip_setsockopt+0x3b/0xb0 net/ipv4/ip_sockglue.c:1246
    [<00000000b9db185c>] udp_setsockopt+0x4e/0x90 net/ipv4/udp.c:2616
    [<000000003028e438>] sock_common_setsockopt+0x38/0x50 net/core/sock.c:3130
    [<0000000015b65589>] __sys_setsockopt+0x98/0x120 net/socket.c:2078
    [<00000000ac198ef0>] __do_sys_setsockopt net/socket.c:2089 [inline]
    [<00000000ac198ef0>] __se_sys_setsockopt net/socket.c:2086 [inline]
    [<00000000ac198ef0>] __x64_sys_setsockopt+0x26/0x30 net/socket.c:2086
    [<000000000a770437>] do_syscall_64+0x76/0x1a0 arch/x86/entry/common.c:301
    [<00000000d3adb93b>] entry_SYSCALL_64_after_hwframe+0x44/0xa9

Fixes: 9c8bb163 ("igmp, mld: Fix memory leak in igmpv3/mld_del_delrec()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Hangbin Liu <liuhangbin@gmail.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>