- 06 Feb, 2023 22 commits
-
-
Oleg Verych authored
Fix interrupt status register offset usage to be a defined name CSI_INT_STA_REG (= 0x34) instead of a plain number. Additionally fix a typo in a comment of the same file. Signed-off-by:
Oleg Verych <olecom@gmail.com> Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@kernel.org>
-
Laurent Pinchart authored
The IMX296LLR is a monochrome 1.60MP CMOS sensor from Sony. The driver supports cropping and binning (but not both at the same time due to hardware limitations) and exposure, gain, vertical blanking and test pattern controls. Preliminary support is also included for the color IMX296LQR sensor. [Sakari Ailus: Make driver's remove function return void] Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Manivannan Sadhasivam authored
Add YAML devicetree binding for IMX296 CMOS image sensor. Let's also add MAINTAINERS entry for the binding and driver. Signed-off-by:
Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Paul Elder authored
Gain control is badly documented in publicly available (including leaked) documentation. There is an AGC pre-gain in register 0x3a13, expressed as a 6-bit value (plus an enable bit in bit 6). The driver hardcodes it to 0x43, which one application note states is equal to x1.047. The documentation also states that 0x40 is equel to x1.000. The pre-gain thus seems to be expressed as in 1/64 increments, and thus ranges from x1.00 to x1.984. What the pre-gain does is however unspecified. There is then an AGC gain limit, in registers 0x3a18 and 0x3a19, expressed as a 10-bit "real gain format" value. One application note sets it to 0x00f8 and states it is equal to x15.5, so it appears to be expressed in 1/16 increments, up to x63.9375. The manual gain is stored in registers 0x350a and 0x350b, also as a 10-bit "real gain format" value. It is documented in the application note as a Q6.4 values, up to x63.9375. One version of the datasheet indicates that the sensor supports a digital gain: The OV5640 supports 1/2/4 digital gain. Normally, the gain is controlled automatically by the automatic gain control (AGC) block. It isn't clear how that would be controlled manually. There appears to be no indication regarding whether the gain controlled through registers 0x350a and 0x350b is an analogue gain only or also includes digital gain. The words "real gain" don't necessarily mean "combined analogue and digital gains". Some OmniVision sensors (such as the OV8858) are documented as supoprting different formats for the gain values, selectable through a register bit, and they are called "real gain format" and "sensor gain format". For that sensor, we have (one of) the gain registers documented as 0x3503[2]=0, gain[7:0] is real gain format, where low 4 bits are fraction bits, for example, 0x10 is 1x gain, 0x28 is 2.5x gain If 0x3503[2]=1, gain[7:0] is sensor gain format, gain[7:4] is coarse gain, 00000: 1x, 00001: 2x, 00011: 4x, 00111: 8x, gain[7] is 1, gain[3:0] is fine gain. For example, 0x10 is 1x gain, 0x30 is 2x gain, 0x70 is 4x gain (The second part of the text makes little sense) "Real gain" may thus refer to the combination of the coarse and fine analogue gains as a single value. The OV5640 0x350a and 0x350b registers thus appear to control analogue gain. The driver incorrectly uses V4L2_CID_GAIN as V4L2 has a specific control for analogue gain, V4L2_CID_ANALOGUE_GAIN. Use it. If registers 0x350a and 0x350b are later found to control digital gain as well, the driver could then restrict the range of the analogue gain control value to lower than x64 and add a separate digital gain control. Signed-off-by:
Paul Elder <paul.elder@ideasonboard.com> Signed-off-by:
Jacopo Mondi <jacopo.mondi@ideasonboard.com> Reviewed-by:
Jai Luthra <j-luthra@ti.com> Signed-off-by:
-
Yuan Can authored
A memory leak was reported when testing ov772x with bpf mock device: AssertionError: unreferenced object 0xffff888109afa7a8 (size 8): comm "python3", pid 279, jiffies 4294805921 (age 20.681s) hex dump (first 8 bytes): 80 22 88 15 81 88 ff ff ."...... backtrace: [<000000009990b438>] __kmalloc_node+0x44/0x1b0 [<000000009e32f7d7>] kvmalloc_node+0x34/0x180 [<00000000faf48134>] v4l2_ctrl_handler_init_class+0x11d/0x180 [videodev] [<00000000da376937>] ov772x_probe+0x1c3/0x68c [ov772x] [<000000003f0d225e>] i2c_device_probe+0x28d/0x680 [<00000000e0b6db89>] really_probe+0x17c/0x3f0 [<000000001b19fcee>] __driver_probe_device+0xe3/0x170 [<0000000048370519>] driver_probe_device+0x49/0x120 [<000000005ead07a0>] __device_attach_driver+0xf7/0x150 [<0000000043f452b8>] bus_for_each_drv+0x114/0x180 [<00000000358e5596>] __device_attach+0x1e5/0x2d0 [<0000000043f83c5d>] bus_probe_device+0x126/0x140 [<00000000ee0f3046>] device_add+0x810/0x1130 [<00000000e0278184>] i2c_new_client_device+0x359/0x4f0 [<0000000070baf34f>] of_i2c_register_device+0xf1/0x110 [<00000000a9f2159d>] of_i2c_notify+0x100/0x160 unreferenced object 0xffff888119825c00 (size 256): comm "python3", pid 279, jiffies 4294805921 (age 20.681s) hex dump (first 32 bytes): 00 b4 a5 17 81 88 ff ff 00 5e 82 19 81 88 ff ff .........^...... 10 5c 82 19 81 88 ff ff 10 5c 82 19 81 88 ff ff .\.......\...... backtrace: [<000000009990b438>] __kmalloc_node+0x44/0x1b0 [<000000009e32f7d7>] kvmalloc_node+0x34/0x180 [<0000000073d88e0b>] v4l2_ctrl_new.cold+0x19b/0x86f [videodev] [<00000000b1f576fb>] v4l2_ctrl_new_std+0x16f/0x210 [videodev] [<00000000caf7ac99>] ov772x_probe+0x1fa/0x68c [ov772x] [<000000003f0d225e>] i2c_device_probe+0x28d/0x680 [<00000000e0b6db89>] really_probe+0x17c/0x3f0 [<000000001b19fcee>] __driver_probe_device+0xe3/0x170 [<0000000048370519>] driver_probe_device+0x49/0x120 [<000000005ead07a0>] __device_attach_driver+0xf7/0x150 [<0000000043f452b8>] bus_for_each_drv+0x114/0x180 [<00000000358e5596>] __device_attach+0x1e5/0x2d0 [<0000000043f83c5d>] bus_probe_device+0x126/0x140 [<00000000ee0f3046>] device_add+0x810/0x1130 [<00000000e0278184>] i2c_new_client_device+0x359/0x4f0 [<0000000070baf34f>] of_i2c_register_device+0xf1/0x110 The reason is that if priv->hdl.error is set, ov772x_probe() jumps to the error_mutex_destroy without doing v4l2_ctrl_handler_free(), and all resources allocated in v4l2_ctrl_handler_init() and v4l2_ctrl_new_std() are leaked. Fixes: 1112babd ("media: i2c: Copy ov772x soc_camera sensor driver") Signed-off-by:Yuan Can <yuancan@huawei.com> Reviewed-by:
-
Yassine Oudjana authored
Make the driver get needed regulators on probe and enable/disable them on runtime PM callbacks. Signed-off-by:
Yassine Oudjana <y.oudjana@protonmail.com> Tested-by:
Umang Jain <umang.jain@ideasonboard.com> Signed-off-by:
-
Yassine Oudjana authored
Add supply properties to describe regulators needed to power the AK7375 VCM. Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Tested-by:
-
Yassine Oudjana authored
Convert DT bindings document for AKM AK7375 VCM to DT schema format and add an example. Signed-off-by:
-
Laurent Pinchart authored
Commit ae219872 ("media: mc: entity: Rewrite media_pipeline_start()") incorrectly referred to entity instead of pad in a comment, and forgot to update a second comment accordingly when moving the pipe from entity to pad. Furthermore, it didn't properly reflow the documentation text it updated. Fix those small issues. Fixes: ae219872 ("media: mc: entity: Rewrite media_pipeline_start()") Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Signed-off-by:
-
Laurent Pinchart authored
Various functions access the media_device from a pad by going through the entity the pad belongs to. Remove the level of indirection and get the media_device from the pad directly. Fixes: 9e3576a1 ("media: mc: convert pipeline funcs to take media_pad") Signed-off-by:
-
Alexander Stein authored
In the probe path, dev_err() can be replaced with dev_err_probe() which will check if error code is -EPROBE_DEFER and prints the error name. It also sets the defer probe reason which can be checked later through debugfs. It's more simple in error path. Signed-off-by:
Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by:
-
Alexander Stein authored
This is not need anyway as the i2c_client is stored in v4l2_subdev. Signed-off-by:
Daniele Alessandrelli <daniele.alessandrelli@intel.com> Signed-off-by:
-
Laurent Pinchart authored
Replace usage of the deprecated media graph walk API with the new media_pipeline_for_each_pad() macro. Signed-off-by:
-
Laurent Pinchart authored
Replace usage of the deprecated media graph walk API with the new media_pipeline_for_each_entity() and media_pipeline_for_each_pad() macros. Even though the entity iterator may seem a better match when build the entity bitmap in iss_video_stream(), it would not be more efficient as it would still iterate internally over all pads. As the entity iterator requires explicit iterator initialization and cleanup calls, the code would be more complex. Signed-off-by:
-
Laurent Pinchart authored
Replace usage of the deprecated media graph walk API with the new media_pipeline_for_each_entity() macro. Signed-off-by:
-
Laurent Pinchart authored
Add a media_pipeline_for_each_entity() macro to iterate over entities in a pipeline. This should be used by driver as a replacement of the media_graph_walk API, as iterating over the media_pipeline uses the cached list of pads and is thus more efficient. Deprecate the media_graph_walk API to indicate it shouldn't be used in new drivers. Signed-off-by:
-
Laurent Pinchart authored
Add a media_pipeline_for_each_pad() macro to iterate over pads in a pipeline. This should be used by driver as a replacement of the media_graph_walk API, as iterating over the media_pipeline uses the cached list of pads and is thus more efficient. Signed-off-by:
-
Jai Luthra authored
Some module manufacturers [1][2] don't expose the RESETB and PWDN pins of the sensor directly through the 15-pin FFC connector. Instead wiring ~PWDN gpio to the sensor pins with appropriate delays. In such cases, reset_gpio will not be available to the driver, but it will still be toggled when the sensor is powered on, and thus we should still honor the wait time of >= 5ms + 1ms + 20ms (see figure 2-3 in [3]) before attempting any i/o operations over SCCB. Also, rename the function to ov5640_powerup_sequence to better match the datasheet (section 2.7). [1] https://digilent.com/reference/_media/reference/add-ons/pcam-5c/pcam_5c_sch.pdf [2] https://www.alinx.com/public/upload/file/AN5641_User_Manual.pdf [3] https://cdn.sparkfun.com/datasheets/Sensors/LightImaging/OV5640_datasheet.pdf Fixes: 19a81c14 ("[media] add Omnivision OV5640 sensor driver") Reported-by:
Nishanth Menon <nm@ti.com> Signed-off-by:
-
Jai Luthra authored
Move the register-based reset out of the init_setting[] and into the powerup_sequence function. The sensor is power cycled and reset using the gpio pins so the soft reset is not always necessary. This also ensures that soft reset honors the timing sequence from the datasheet [1]. [1] https://cdn.sparkfun.com/datasheets/Sensors/LightImaging/OV5640_datasheet.pdf Fixes: 19a81c14 ("[media] add Omnivision OV5640 sensor driver") Reported-by:
Jacopo Mondi <jacopo.mondi@ideasonaboard.com> Signed-off-by:
-
Andy Shevchenko authored
There is no point to specify asm-generic for the unaligned.h. Drop the 'generic' suffix and move the inclusion to be after the non-media linux/* ones. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by:
Benjamin Mugnier <benjamin.mugnier@foss.st.com> Signed-off-by:
-
Andrey Skvortsov authored
Otherwise autosuspend delay doesn't work and power is cut off immediately as device is freed. Signed-off-by:
Andrey Skvortsov <andrej.skvortzov@gmail.com> Signed-off-by:
-
Nicholas Roth authored
Add a driver for OmniVision OV8858 image sensor. The driver currently supports operations with 2 and 4 data lanes, in full resolution and half-binned resolution modes. The driver has been upported from the PinephonePro BSP available at https://gitlab.com/pine64-org/linux.git at commit 8c4a90c12dc2 ("media: i2c: ov8858: Use default subdev name"). Signed-off-by:
Nicholas Roth <nicholas@rothemail.net> Signed-off-by:
-
- 03 Feb, 2023 18 commits
-
-
Jacopo Mondi authored
Add binding schema for the OmniVision OV8858 8 Megapixels camera sensor. Signed-off-by:
-
Laurent Pinchart authored
Check the error status returned by imx290_set_data_lanes() in its caller and propagate it. Signed-off-by:
-
Laurent Pinchart authored
There's no need to check for an incorrect number of data lanes in imx290_set_data_lanes() as the value is validated at probe() time. Drop the check. The PHY_LANE_NUM and CSI_LANE_MODE registers are programmed with a value equal to the number of lanes minus one. Compute it instead of handling it in the switch/case. Signed-off-by:
-
Laurent Pinchart authored
There's no need to configure the data lanes in the runtime PM resume handler. Do so in imx290_start_streaming() instead. Signed-off-by:
-
Laurent Pinchart authored
Initializing the subdev before runtime PM means that no subdev initialization can interact with the runtime PM framework. This can be problematic when modifying controls, as the .s_ctrl() handler commonly calls pm_runtime_get_if_in_use(). These code paths are not trivial, making the driver fragile and possibly causing subtle bugs. To make the subdev initialization more robust, initialize runtime PM first. Signed-off-by:
-
Laurent Pinchart authored
Use runtime PM autosuspend to avoid powering off the sensor during fast stop-reconfigure-restart cycles. This also fixes runtime PM handling in the probe function that didn't suspend the device, effectively leaving it resumed forever. While at it, improve documentation of power management in probe() and remove(). Signed-off-by:
-
Laurent Pinchart authored
The imx290_pixfmt structure contains information about formats, currently limited to the bpp value. Extend it with the register settings for each format, and rename it to imx290_format_info to make its purpose clearer. Add a function named imx290_format_info() to look up format info for a media bus code, and use it through the code. This allows dropping the imx290 bpp field as the value is now looked up dynamically. The error handling in imx290_setup_format() can also be dropped, as the format is guaranteed by imx290_set_fmt() to be valid. Signed-off-by:
-
Laurent Pinchart authored
Use the V4L2 subdev active state API to store the active format. This simplifies the driver not only by dropping the imx290 current_format field, but it also allows dropping the imx290 lock, replaced with the state lock. The lock check in imx290_ctrl_update() can be dropped as imx290_set_fmt() can't be called anywmore with which set to ACTIVE before controls are initialized. Signed-off-by:
-
Laurent Pinchart authored
Move the external clock initialization code from probe() to a separate function to improve readability. No functional change intended. Signed-off-by:
-
Laurent Pinchart authored
Improve error handling in the probe() function with dev_err_probe(). Signed-off-by:
-
Laurent Pinchart authored
Make the probe() function more readable by factoring out the DT parsing code to a separate function. No functional change intended. Signed-off-by:
-
Laurent Pinchart authored
The black level programmed in the BLKLEVEL register depends on the output format. The black level value computation is currently performed in imx290_set_ctrl(), in addition to having different black level values in the output-specific register value tables. Move it to a separate function to simplify the imx290_set_ctrl() code. Signed-off-by:
Dave Stevenson <dave.stevenson@raspberrypi.com> Signed-off-by:
-
Laurent Pinchart authored
The hblank, vblank, pixel rate and link frequency values and limits are currently computed when creating controls, in imx290_ctrl_init(), and updated in imx290_ctrl_update(). This duplicates the logic in different places. Simplify the code by setting the control values and limits to hardcoded values when creating the controls, and call imx290_ctrl_update() to then update them. Signed-off-by:
-
Laurent Pinchart authored
Avoid accessing the imx290 current_format and current_mode fields in imx290_calc_pixel_rate() to prepare for the removal of those fields. Among the two callers of the function, imx290_ctrl_update() has an explicit mode pointer already, and we can also give it a format pointer. Use those explicitly. While at it, inline the imx290_get_link_freq() function in imx290_calc_pixel_rate() as it is only called there. Signed-off-by:
-
Laurent Pinchart authored
The imx290_get_link_freq_index() function hides the fact that it relies on the imx290 current_mode field, which obfuscates the code instead of making it more readable. Inline it in the callers, and use the mode pointer we already have in imx290_ctrl_update() instead of using the current_mode field. Signed-off-by:
-
Laurent Pinchart authored
Move the control update code to a separate function to group it with all the control-related code and make imx290_set_fmt() more readable. Signed-off-by:
-
Laurent Pinchart authored
The probe() function is large. Make it more readable by factoring the subdev initialization code out. While at it, rename the error labels as the "free_" prefix isn't accurate. No functional change intended. Signed-off-by:
-
Laurent Pinchart authored
Move functions around to group them in logical sections, in order to improve readability. As a result, the IMX290_NUM_SUPPLIES macro has to be changed. No other code change is included, only moves. Signed-off-by:
-
