- 26 Mar, 2015 40 commits
-
-
Takashi Iwai authored
commit 2ddee91a upstream. MacBook Air 5,2 has the same problem as MacBook Pro 8,1 where the built-in mic records only the right channel. Apply the same workaround as MBP8,1 to spread the mono channel via a Cirrus codec vendor-specific COEF setup. Reported-and-tested-by:
Vasil Zlatanov <vasil.zlatanov@gmail.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Takashi Iwai authored
commit bad994f5 upstream. CS420x codecs seem to deal only the single amps of ADC nodes even though the nodes receive multiple inputs. This leads to the inconsistent amp value after S3/S4 resume, for example. The fix is just to set codec->single_adc_amp flag. Then the driver handles these ADC amps as if single connections. Reported-and-tested-by:
-
Takashi Iwai authored
commit ef403edb upstream. The current HDA generic parser initializes / modifies the amp values always in stereo, but this seems causing the problem on ALC3229 codec that has a few mono channel widgets: namely, these mono widgets react to actions for both channels equally. In the driver code, we do care the mono channel and create a control only for the left channel (as defined in HD-audio spec) for such a node. When the control is updated, only the left channel value is changed. However, in the resume, the right channel value is also restored from the initial value we took as stereo, and this overwrites the left channel value. This ends up being the silent output as the right channel has been never touched and remains muted. This patch covers the places where unconditional stereo amp accesses are done and converts to the conditional accesses. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94581Signed-off-by:
-
Takashi Iwai authored
commit ddb6ca75 upstream. Compaq Presario CQ60 laptop with CX20561 gives a wrong pin for the built-in mic NID 0x17 instead of NID 0x1d, and it results in the non-working mic. This patch just remaps the pin correctly via fixup. Bugzilla: https://bugzilla.opensuse.org/show_bug.cgi?id=920604Signed-off-by:
-
Takashi Iwai authored
commit be3bb823 upstream. There was no check about the id string of user control elements, so we accepted even a control element with an empty string, which is obviously bogus. This patch adds more sanity checks of id strings. Signed-off-by:
-
Daniel Mack authored
commit fcdcd1de upstream. The device complies to the UAC1 standard but hides that fact with proprietary descriptors. The autodetect quirk for Roland devices catches the audio interface but misses the MIDI part, so a specific quirk is needed. Signed-off-by:
Daniel Mack <daniel@zonque.org> Reported-by:
Rafa Lafuente <rafalafuente@gmail.com> Tested-by:
Raphaël Doursenaud <raphael@doursenaud.fr> Signed-off-by:
-
Alexander Sverdlin authored
commit cd6fa8d2 upstream. Commit fd316941 ("spi/pl022: disable port when unused") introduced a race, which leads to possible driver lock up (easily reproducible on SMP). The problem happens in giveback() function where the completion of the transfer is signalled to SPI subsystem and then the HW SPI controller is disabled. Another transfer might be setup in between, which brings driver in locked-up state. Exact event sequence on SMP: core0 core1 => pump_transfers() /* message->state == STATE_DONE */ => giveback() => spi_finalize_current_message() => pl022_unprepare_transfer_hardware() => pl022_transfer_one_message => flush() => do_interrupt_dma_transfer() => set_up_next_transfer() /* Enable SSP, turn on interrupts */ writew((readw(SSP_CR1(pl022->virtbase)) | SSP_CR1_MASK_SSE), SSP_CR1(pl022->virtbase)); ... => pl022_interrupt_handler() => readwriter() /* disable the SPI/SSP operation */ => writew((readw(SSP_CR1(pl022->virtbase)) & (~SSP_CR1_MASK_SSE)), SSP_CR1(pl022->virtbase)); Lockup! SPI controller is disabled and the data will never be received. Whole SPI subsystem is waiting for transfer ACK and blocked. So, only signal transfer completion after disabling the controller. Fixes: fd316941 (spi/pl022: disable port when unused) Signed-off-by:
Alexander Sverdlin <alexander.sverdlin@nokia.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Andy Shevchenko authored
commit c9dafb27 upstream. When DMA descriptor allocation fails we should not try to assign any fields in the bad descriptor. The patch adds the necessary checks for that. Fixes: 7063c0d9 (spi/dw_spi: add DMA support) Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
-
Torsten Fleischer authored
commit 76e1d14b upstream. Additionally to the current DMA transfer the PDC allows to set up a next DMA transfer. This is useful for larger SPI transfers. The driver currently waits for ENDRX as end of the transfer. But ENDRX is set when the current DMA transfer is done (RCR = 0), i.e. it doesn't include the next DMA transfer. Thus a subsequent SPI transfer could be started although there is currently a transfer in progress. This can cause invalid accesses to the SPI slave devices and to SPI transfer errors. This issue has been observed on a hardware with a M25P128 SPI NOR flash. So instead of ENDRX we should wait for RXBUFF. This flag is set if there is no more DMA transfer in progress (RCR = RNCR = 0). Signed-off-by:
Torsten Fleischer <torfl6749@gmail.com> Signed-off-by:
-
Sebastian Ott authored
commit f0483044 upstream. Make sure that even in error situations we do not use copy_to_user on uninitialized kernel memory. Signed-off-by:
Sebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
-
Christophe Ricard authored
commit c4eadfaf upstream. Add a return value check when reading data from the FIFO register. Reviewed-by:
Jason Gunthorpe <jason.gunthorpe@obsidianresearch.com> Signed-off-by:
Christophe Ricard <christophe-h.ricard@st.com> Reviewed-by:
Peter Huewe <peterhuewe@gmx.de> Signed-off-by:
-
jmlatten@linux.vnet.ibm.com authored
commit 62dfd912 upstream. Problem: When IMA and VTPM are both enabled in kernel config, kernel hangs during bootup on LE OS. Why?: IMA calls tpm_pcr_read() which results in tpm_ibmvtpm_send and tpm_ibmtpm_recv getting called. A trace showed that tpm_ibmtpm_recv was hanging. Resolution: tpm_ibmtpm_recv was hanging because tpm_ibmvtpm_send was sending CRQ message that probably did not make much sense to phype because of Endianness. The fix below sends correctly converted CRQ for LE. This was not caught before because it seems IMA is not enabled by default in kernel config and IMA exercises this particular code path in vtpm. Tested with IMA and VTPM enabled in kernel config and VTPM enabled on both a BE OS and a LE OS ppc64 lpar. This exercised CRQ and TPM command code paths in vtpm. Patch is against Peter's tpmdd tree on github which included Vicky's previous vtpm le patches. Signed-off-by:
Joy Latten <jmlatten@linux.vnet.ibm.com> Reviewed-by:
Ashley Lai <ashley@ahsleylai.com> Signed-off-by:
-
Jason Low authored
commit 283cb41f upstream. The cpuset.sched_relax_domain_level can control how far we do immediate load balancing on a system. However, it was found on recent kernels that echo'ing a value into cpuset.sched_relax_domain_level did not reduce any immediate load balancing. The reason this occurred was because the update_domain_attr_tree() traversal did not update for the "top_cpuset". This resulted in nothing being changed when modifying the sched_relax_domain_level parameter. This patch is able to address that problem by having update_domain_attr_tree() allow updates for the root in the cpuset traversal. Fixes: fc560a26 ("cpuset: replace cpuset->stack_list with cpuset_for_each_descendant_pre()") Signed-off-by:
Jason Low <jason.low2@hp.com> Signed-off-by:
Zefan Li <lizefan@huawei.com> Signed-off-by:
Tejun Heo <tj@kernel.org> Tested-by:
Serge Hallyn <serge.hallyn@canonical.com> Signed-off-by:
-
Zefan Li authored
commit 79063bff upstream. When we clear cpuset.cpus, cpuset.effective_cpus won't be cleared: # mount -t cgroup -o cpuset xxx /mnt # mkdir /mnt/tmp # echo 0 > /mnt/tmp/cpuset.cpus # echo > /mnt/tmp/cpuset.cpus # cat cpuset.cpus # cat cpuset.effective_cpus 0-15 And a kernel warning in update_cpumasks_hier() is triggered: ------------[ cut here ]------------ WARNING: CPU: 0 PID: 4028 at kernel/cpuset.c:894 update_cpumasks_hier+0x471/0x650() Signed-off-by:
-
Zefan Li authored
commit 790317e1 upstream. If clone_children is enabled, effective masks won't be initialized due to the bug: # mount -t cgroup -o cpuset xxx /mnt # echo 1 > cgroup.clone_children # mkdir /mnt/tmp # cat /mnt/tmp/ # cat cpuset.effective_cpus # cat cpuset.cpus 0-15 And then this cpuset won't constrain the tasks in it. Either the bug or the fix has no effect on unified hierarchy, as there's no clone_chidren flag there any more. Reported-by:
Christian Brauner <christianvanbrauner@gmail.com> Reported-by:
Serge Hallyn <serge.hallyn@ubuntu.com> Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit 4d4eb4d4 upstream. In seq_buf_bprintf(), bstr_printf() is used to copy the format into the buffer remaining in the seq_buf structure. The return of bstr_printf() is the amount of characters written to the buffer excluding the '\0', unless the line was truncated! If the line copied does not fit, it is truncated, and a '\0' is added to the end of the buffer. But in this case, '\0' is included in the length of the line written. To know if the buffer had overflowed, the return length will be the same or greater than the length of the buffer passed in. The check in seq_buf_bprintf() only checked if the length returned from bstr_printf() would fit in the buffer, as the seq_buf_bprintf() is only to be an all or nothing command. It either writes all the string into the seq_buf, or none of it. If the string is truncated, the pointers inside the seq_buf must be reset to what they were when the function was called. This is not the case. On overflow, it copies only part of the string. The fix is to change the overflow check to see if the length returned from bstr_printf() is less than the length remaining in the seq_buf buffer, and not if it is less than or equal to as it currently does. Then seq_buf_bprintf() will know if the write from bstr_printf() was truncated or not. Link: http://lkml.kernel.org/r/1425500481.2712.27.camel@perches.comReported-by:
Joe Perches <joe@perches.com> Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit 4a8fe4e1 upstream. In seq_buf_vprintf(), vsnprintf() is used to copy the format into the buffer remaining in the seq_buf structure. The return of vsnprintf() is the amount of characters written to the buffer excluding the '\0', unless the line was truncated! If the line copied does not fit, it is truncated, and a '\0' is added to the end of the buffer. But in this case, '\0' is included in the length of the line written. To know if the buffer had overflowed, the return length will be the same as the length of the buffer passed in. The check in seq_buf_vprintf() only checked if the length returned from vsnprintf() would fit in the buffer, as the seq_buf_vprintf() is only to be an all or nothing command. It either writes all the string into the seq_buf, or none of it. If the string is truncated, the pointers inside the seq_buf must be reset to what they were when the function was called. This is not the case. On overflow, it copies only part of the string. The fix is to change the overflow check to see if the length returned from vsnprintf() is less than the length remaining in the seq_buf buffer, and not if it is less than or equal to as it currently does. Then seq_buf_vprintf() will know if the write from vsnpritnf() was truncated or not. Signed-off-by:
-
Tejun Heo authored
commit 8603e1b3 upstream. cancel[_delayed]_work_sync() are implemented using __cancel_work_timer() which grabs the PENDING bit using try_to_grab_pending() and then flushes the work item with PENDING set to prevent the on-going execution of the work item from requeueing itself. try_to_grab_pending() can always grab PENDING bit without blocking except when someone else is doing the above flushing during cancelation. In that case, try_to_grab_pending() returns -ENOENT. In this case, __cancel_work_timer() currently invokes flush_work(). The assumption is that the completion of the work item is what the other canceling task would be waiting for too and thus waiting for the same condition and retrying should allow forward progress without excessive busy looping Unfortunately, this doesn't work if preemption is disabled or the latter task has real time priority. Let's say task A just got woken up from flush_work() by the completion of the target work item. If, before task A starts executing, task B gets scheduled and invokes __cancel_work_timer() on the same work item, its try_to_grab_pending() will return -ENOENT as the work item is still being canceled by task A and flush_work() will also immediately return false as the work item is no longer executing. This puts task B in a busy loop possibly preventing task A from executing and clearing the canceling state on the work item leading to a hang. task A task B worker executing work __cancel_work_timer() try_to_grab_pending() set work CANCELING flush_work() block for work completion completion, wakes up A __cancel_work_timer() while (forever) { try_to_grab_pending() -ENOENT as work is being canceled flush_work() false as work is no longer executing } This patch removes the possible hang by updating __cancel_work_timer() to explicitly wait for clearing of CANCELING rather than invoking flush_work() after try_to_grab_pending() fails with -ENOENT. Link: http://lkml.kernel.org/g/20150206171156.GA8942@axis.com v3: bit_waitqueue() can't be used for work items defined in vmalloc area. Switched to custom wake function which matches the target work item and exclusive wait and wakeup. v2: v1 used wake_up() on bit_waitqueue() which leads to NULL deref if the target bit waitqueue has wait_bit_queue's on it. Use DEFINE_WAIT_BIT() and __wake_up_bit() instead. Reported by Tomeu Vizoso. Signed-off-by:
Rabin Vincent <rabin.vincent@axis.com> Cc: Tomeu Vizoso <tomeu.vizoso@gmail.com> Tested-by:
Jesper Nilsson <jesper.nilsson@axis.com> Tested-by:
-
Ahmed S. Darwish authored
commit 2fec5104 upstream. The Kvaser firmware can only read and write messages that are not crossing the USB endpoint's wMaxPacketSize boundary. While receiving commands from the CAN device, if the next command in the same URB buffer crossed that max packet size boundary, the firmware puts a zero-length placeholder command in its place then moves the real command to the next boundary mark. The driver did not recognize such behavior, leading to missing a good number of rx events during a heavy rx load session. Moreover, a tx URB context only gets freed upon receiving its respective tx ACK event. Over time, the free tx URB contexts pool gets depleted due to the missing ACK events. Consequently, the netif transmission queue gets __permanently__ stopped; no frames could be sent again except after restarting the CAN newtwork interface. Signed-off-by:
Ahmed S. Darwish <ahmed.darwish@valeo.com> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
Oliver Hartkopp authored
commit 96943901 upstream. When accessing CAN network interfaces with AF_PACKET sockets e.g. by dhclient this can lead to a skb_under_panic due to missing skb initialisations. Add the missing initialisations at the CAN skbuff creation times on driver level (rx path) and in the network layer (tx path). Reported-by:
Austin Schuh <austin@peloton-tech.com> Reported-by:
Daniel Steer <daniel.steer@mclaren.com> Signed-off-by:
Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit 524a3868 upstream. Some archs (specifically PowerPC), are sensitive with the ordering of the enabling of the calls to function tracing and setting of the function to use to be traced. That is, update_ftrace_function() sets what function the ftrace_caller trampoline should call. Some archs require this to be set before calling ftrace_run_update_code(). Another bug was discovered, that ftrace_startup_sysctl() called ftrace_run_update_code() directly. If the function the ftrace_caller trampoline changes, then it will not be updated. Instead a call to ftrace_startup_enable() should be called because it tests to see if the callback changed since the code was disabled, and will tell the arch to update appropriately. Most archs do not need this notification, but PowerPC does. The problem could be seen by the following commands: # echo 0 > /proc/sys/kernel/ftrace_enabled # echo function > /sys/kernel/debug/tracing/current_tracer # echo 1 > /proc/sys/kernel/ftrace_enabled # cat /sys/kernel/debug/tracing/trace The trace will show that function tracing was not active. Signed-off-by:
-
Pratyush Anand authored
commit 1619dc3f upstream. When ftrace is enabled globally through the proc interface, we must check if ftrace_graph_active is set. If it is set, then we should also pass the FTRACE_START_FUNC_RET command to ftrace_run_update_code(). Similarly, when ftrace is disabled globally through the proc interface, we must check if ftrace_graph_active is set. If it is set, then we should also pass the FTRACE_STOP_FUNC_RET command to ftrace_run_update_code(). Consider the following situation. # echo 0 > /proc/sys/kernel/ftrace_enabled After this ftrace_enabled = 0. # echo function_graph > /sys/kernel/debug/tracing/current_tracer Since ftrace_enabled = 0, ftrace_enable_ftrace_graph_caller() is never called. # echo 1 > /proc/sys/kernel/ftrace_enabled Now ftrace_enabled will be set to true, but still ftrace_enable_ftrace_graph_caller() will not be called, which is not desired. Further if we execute the following after this: # echo nop > /sys/kernel/debug/tracing/current_tracer Now since ftrace_enabled is set it will call ftrace_disable_ftrace_graph_caller(), which causes a kernel warning on the ARM platform. On the ARM platform, when ftrace_enable_ftrace_graph_caller() is called, it checks whether the old instruction is a nop or not. If it's not a nop, then it returns an error. If it is a nop then it replaces instruction at that address with a branch to ftrace_graph_caller. ftrace_disable_ftrace_graph_caller() behaves just the opposite. Therefore, if generic ftrace code ever calls either ftrace_enable_ftrace_graph_caller() or ftrace_disable_ftrace_graph_caller() consecutively two times in a row, then it will return an error, which will cause the generic ftrace code to raise a warning. Note, x86 does not have an issue with this because the architecture specific code for ftrace_enable_ftrace_graph_caller() and ftrace_disable_ftrace_graph_caller() does not check the previous state, and calling either of these functions twice in a row has no ill effect. Link: http://lkml.kernel.org/r/e4fbe64cdac0dd0e86a3bf914b0f83c0b419f146.1425666454.git.panand@redhat.comSigned-off-by:
Pratyush Anand <panand@redhat.com> [ removed extra if (ftrace_start_up) and defined ftrace_graph_active as 0 if CONFIG_FUNCTION_GRAPH_TRACER is not set. ] Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit b24d443b upstream. When /proc/sys/kernel/ftrace_enabled is set to zero, all function tracing is disabled. But the records that represent the functions still hold information about the ftrace_ops that are hooked to them. ftrace_ops may request "REGS" (have a full set of pt_regs passed to the callback), or "TRAMP" (the ops has its own trampoline to use). When the record is updated to represent the state of the ops hooked to it, it sets "REGS_EN" and/or "TRAMP_EN" to state that the callback points to the correct trampoline (REGS has its own trampoline). When ftrace_enabled is set to zero, all ftrace locations are a nop, so they do not point to any trampoline. But the _EN flags are still set. This can cause the accounting to go wrong when ftrace_enabled is cleared and an ops that has a trampoline is registered or unregistered. For example, the following will cause ftrace to crash: # echo function_graph > /sys/kernel/debug/tracing/current_tracer # echo 0 > /proc/sys/kernel/ftrace_enabled # echo nop > /sys/kernel/debug/tracing/current_tracer # echo 1 > /proc/sys/kernel/ftrace_enabled # echo function_graph > /sys/kernel/debug/tracing/current_tracer As function_graph uses a trampoline, when ftrace_enabled is set to zero the updates to the record are not done. When enabling function_graph again, the record will still have the TRAMP_EN flag set, and it will look for an op that has a trampoline other than the function_graph ops, and fail to find one. Reported-by:
-
Russell King authored
commit f2e0ea86 upstream. I'm still receiving reports to my email address, so let's point this at the linux-serial mailing list instead. Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by:
-
Michael S. Tsirkin authored
commit eeb8a7e8 upstream. when multiport is off, virtio console invokes config access from irq context, config access is blocking on s390. Fix this up by scheduling work from config irq - similar to what we do for multiport configs. Signed-off-by:
Michael S. Tsirkin <mst@redhat.com> Reviewed-by:
Amit Shah <amit.shah@redhat.com> Signed-off-by:
Rusty Russell <rusty@rustcorp.com.au> Signed-off-by:
-
Michael S. Tsirkin authored
commit 4f6e24ed upstream. when multiport is off, we don't initialize config work, but we then cancel uninitialized control_work on freeze. Signed-off-by:
-
Peter Hurley authored
commit 30a22c21 upstream. commit 6ae9200f ("enlarge console.name") increased the storage for the console name to 16 bytes, but not the corresponding struct console_cmdline::name storage. Console names longer than 8 bytes cause read beyond end-of-string and failure to match console; I'm not sure if there are other unexpected consequences. Signed-off-by:
Peter Hurley <peter@hurleysoftware.com> Signed-off-by:
-
Peter Hurley authored
commit 7fd6f640 upstream. Trying to write console output from within the serial console driver while the port->lock is held causes recursive deadlock: CPU 0 spin_lock_irqsave(&port->lock) printk() console_unlock() call_console_drivers() serial8250_console_write() spin_lock_irqsave(&port->lock) ** DEADLOCK ** The 8250_dw i/o accessors try to write a console error message if the LCR workaround was unsuccessful. When the port->lock is already held (eg., when called from serial8250_set_termios()), this deadlocks. Make the error message a FIXME until a general solution is devised. Cc: Tim Kryger <tim.kryger@gmail.com> Reported-by:
Zhang Zhen <zhenzhang.zhang@huawei.com> Signed-off-by:
-
Peter Hurley authored
commit 2bb78516 upstream. commit 3ffb1a81 ("serial: core: Add big-endian iotype") re-numbered userspace-dependent values; ioctl(TIOCSSERIAL) can assign the port iotype (which is expected to match the selected i/o accessors), so iotype values must not be changed. Cc: Kevin Cernekee <cernekee@gmail.com> Signed-off-by:
Kevin Cernekee <cernekee@gmail.com> Signed-off-by:
-
Miklos Szeredi authored
commit 0d278362 upstream. fuse_try_move_page() is not prepared for replacing pages that have already been read. Reported-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
Miklos Szeredi <mszeredi@suse.cz> Signed-off-by:
-
Miklos Szeredi authored
commit aa991b3b upstream. Regular pipe buffers' ->steal method (generic_pipe_buf_steal()) doesn't set PG_uptodate. Don't warn on this condition, just set the uptodate flag. Signed-off-by:
-
JeHyeon Yeon authored
commit d5e7cafd upstream. If the part of the compression data are corrupted, or the compression data is totally fake, the memory access over the limit is possible. This is the log from my system usning lz4 decompression. [6502]data abort, halting [6503]r0 0x00000000 r1 0x00000000 r2 0xdcea0ffc r3 0xdcea0ffc [6509]r4 0xb9ab0bfd r5 0xdcea0ffc r6 0xdcea0ff8 r7 0xdce80000 [6515]r8 0x00000000 r9 0x00000000 r10 0x00000000 r11 0xb9a98000 [6522]r12 0xdcea1000 usp 0x00000000 ulr 0x00000000 pc 0x820149bc [6528]spsr 0x400001f3 and the memory addresses of some variables at the moment are ref:0xdcea0ffc, op:0xdcea0ffc, oend:0xdcea1000 As you can see, COPYLENGH is 8bytes, so @ref and @op can access the momory over @oend. Signed-off-by:
JeHyeon Yeon <tom.yeon@windriver.com> Reviewed-by:
David Sterba <dsterba@suse.cz> Signed-off-by:
-
Alex Deucher authored
commit a239118a upstream. radeon_bo_create() calls radeon_ttm_placement_from_domain() before ttm_bo_init() is called. radeon_ttm_placement_from_domain() uses the ttm bo size to determine when to select top down allocation but since the ttm bo is not initialized yet the check is always false. It only took effect when buffers were validated later. It also seemed to regress suspend and resume on some systems possibly due to it not taking effect in radeon_bo_create(). radeon_bo_create() and radeon_ttm_placement_from_domain() need to be reworked substantially for this to be optimally effective. Re-enable it at that point. Noticed-by:
Oded Gabbay <oded.gabbay@amd.com> Reviewed-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Ben Goz authored
commit e405ca3a upstream. The current CP firmware can handle Usermode Queues only on MEC1. To reflect this firmware change, this commit reduces number of compute pipelines to 4 - 1, from 8 - 1 (the first pipeline is allocated for kgd). Signed-off-by:
Ben Goz <ben.goz@amd.com> Signed-off-by:
-
Maarten Lankhorst authored
commit b6610101 upstream. A normal wait adds to the front of the tail. By doing something similar to fence_default_wait the fence code can run without racing. This is a complete fix for "panic on suspend from KDE with radeon", and a partial fix for "Radeon: System pauses on TAHITI". On tahiti si_irq_set needs to be fixed too, to completely flush the writes before radeon_fence_activity is called in radeon_fence_enable_signaling. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=90741 Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=90861Signed-off-by:
Maarten Lankhorst <maarten.lankhorst@ubuntu.com> Reported-by:
Jon Arne Jørgensen <jonjon.arnearne@gmail.com> Reported-and-tested-by:
Gustaw Smolarczyk <wielkiegie@gmail.com> Signed-off-by:
-
Christian König authored
commit a17d4996 upstream. Just keep it working, seems to fix some PLL problems. Bug: https://bugs.freedesktop.org/show_bug.cgi?id=73378Signed-off-by:
-
Alex Deucher authored
commit 77ae5f4b upstream. Need to double the viewport height. Signed-off-by:
-
Alex Deucher authored
commit 54acf107 upstream. To make sure the writes go through the pci bridge. bug: https://bugzilla.kernel.org/show_bug.cgi?id=90741Signed-off-by:
-
Alex Deucher authored
commit 0586915e upstream. To make sure the writes go through the pci bridge. bug: https://bugzilla.kernel.org/show_bug.cgi?id=90741Signed-off-by:
-
Alex Deucher authored
commit cffefd9b upstream. To make sure the writes go through the pci bridge. bug: https://bugzilla.kernel.org/show_bug.cgi?id=90741Signed-off-by:
-
