- Add UniPhier PCIe controller driver and DT bindings (Kunihiko Hayashi)

* remotes/lorenzo/pci/uniphier:
  PCI: uniphier: Add UniPhier PCIe host controller support
  dt-bindings: PCI: Add UniPhier PCIe host controller description

# Conflicts:
#	drivers/pci/controller/dwc/Kconfig
#	drivers/pci/controller/dwc/Makefile

  - Use devm resource parser in mediatek (Honghui Zhang)

  - Remove unused mediatek "num-lanes" DT property (Honghui Zhang)

* remotes/lorenzo/pci/mediatek:
  arm64: dts: mt7622: Remove un-used property for PCIe
  arm: dts: mt7623: Remove un-used property for PCIe
  dt-bindings: PCI: MediaTek: Remove un-used property
  PCI: mediatek: Remove un-used variant in struct mtk_pcie_port
  PCI: mediatek: Use devm_of_pci_get_host_bridge_resources() to parse DT

  - Mask DesignWare interrupts instead of disabling them to avoid lost
    interrupts (Marc Zyngier)

  - Add locking when acking DesignWare interrupts (Marc Zyngier)

  - Ack DesignWare interrupts in the proper callbacks (Marc Zyngier)

* remotes/lorenzo/pci/dwc-msi:
  PCI: dwc: Move interrupt acking into the proper callback
  PCI: dwc: Take lock when ACKing an interrupt
  PCI: dwc: Use interrupt masking instead of disabling

  - Constify histb dw_pcie_host_ops structure (Julia Lawall)

  - Support multiple power domains for imx6 (Leonard Crestez)

  - Constify layerscape driver data (Stefan Agner)

  - Update imx6 Kconfig to allow imx6 PCIe in imx7 kernel (Trent Piepho)

  - Support armada8k GPIO reset (Baruch Siach)

  - Support suspend/resume support on imx6 (Leonard Crestez)

  - Don't hard-code DesignWare DBI/ATU offst (Stephen Warren)

  - Skip i.MX6 PHY setup on i.MX7D (Andrey Smirnov)

  - Remove Jianguo Sun from HiSilicon STB maintainers (Lorenzo Pieralisi)

* remotes/lorenzo/pci/dwc:
  MAINTAINERS: Remove Jianguo Sun from HiSilicon STB DWC entry
  PCI: dwc: Don't hard-code DBI/ATU offset
  PCI: imx: Add imx6sx suspend/resume support
  PCI: armada8k: Add support for gpio controlled reset signal
  PCI: dwc: Adjust Kconfig to allow IMX6 PCIe host on IMX7
  PCI: dwc: layerscape: Constify driver data
  PCI: imx: Add multi-pd support
  dt-bindings: imx6q-pcie: Add multi-pd bindings for imx6sx
  PCI: histb: Constify dw_pcie_host_ops structure

  - Add Amlogic Meson PCIe controller driver and DT bindings (Yue Wang)

* remotes/lorenzo/pci/amlogic:
  PCI: amlogic: Add the Amlogic Meson PCIe controller driver
  dt-bindings: PCI: meson: add DT bindings for Amlogic Meson PCIe controller

  - Skip VF scanning on powerpc, which does this in firmware (Sebastian
    Ott)

* pci/virtualization:
  s390/pci: skip VF scanning
  PCI/IOV: Add flag so platforms can skip VF scanning
  PCI/IOV: Factor out sriov_add_vfs()

  - Remove status check after submitting Switchtec MRPC Firmware Download
    commands to avoid Completion Timeouts (Kelvin Cao)

  - Set Switchtec coherent DMA mask to allow 64-bit DMA (Boris Glimcher)

  - Fix Switchtec SWITCHTEC_IOCTL_EVENT_IDX_ALL flag overwrite issue (Joey
    Zhang)

  - Enable write combining for Switchtec MRPC Input buffers (Kelvin Cao)

  - Add Switchtec MRPC DMA mode support (Wesley Sheng)

* pci/switchtec:
  switchtec: Add MRPC DMA mode support
  switchtec: Improve MRPC efficiency by enabling write combining
  switchtec: Fix SWITCHTEC_IOCTL_EVENT_IDX_ALL flags overwrite
  switchtec: Set DMA coherent mask
  switchtec: Remove immediate status check after submitting MRPC command

  - Allow runtime PM even if driver doesn't supply callbacks (Jarkko
    Nikula)

* pci/pm:
  PCI / PM: Allow runtime PM without callback functions

  - Clean up P2PDMA documentation (Randy Dunlap)

* pci/peer-to-peer:
  PCI/P2PDMA: Clean up documentation and kernel-doc

  - Expand Kconfig "PF" acronyms (Randy Dunlap)

  - Update MAINTAINERS for arch/x86/kernel/early-quirks.c (Bjorn Helgaas)

  - Add missing include to drivers/pci.h (Alexandru Gagniuc)

  - Override Synopsys USB 3.x HAPS device class so dwc3-haps can claim it
    instead of xhci (Thinh Nguyen)

* pci/misc:
  PCI: Override Synopsys USB 3.x HAPS device class
  PCI: Move Synopsys HAPS platform device IDs
  PCI: Add missing include to drivers/pci.h
  PCI: Remove unnecessary space before function pointer arguments
  MAINTAINERS: Add x86 early-quirks.c file pattern to PCI subsystem
  PCI: Expand the "PF" acronym in Kconfig help text

  - Fix Broadcom CNB20LE host bridge unintended sign extension (Colin Ian
    King)

* pci/enumeration:
  x86/PCI: Fix Broadcom CNB20LE unintended sign extension (redux)

  - Remove unused lists from ASPM pcie_link_state (Frederick Lawler)

* pci/aspm:
  PCI/ASPM: Remove unused lists from struct pcie_link_state

Set the flag to skip scanning for VFs after SR-IOV enablement.  VF creation
will be triggered by the hotplug code.
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>

Provide a flag to skip scanning for new VFs after SR-IOV enablement.  This
can be set by implementations for which the VFs are already reported by
other means.
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>

Provide sriov_add_vfs() as a wrapper to scan for VFs that cleans up after
itself.  This is just a code simplification.  No functional change.
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>

This introduces specific glue layer for UniPhier platform to support
PCIe host controller that is based on the DesignWare PCIe core, and
this driver supports Root Complex (host) mode.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

Add DT bindings for PCIe controller implemented in UniPhier SoCs when
configured in Root Complex (host) mode. This controller is based on
the DesignWare PCIe core.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>

The Amlogic Meson PCIe host controller is based on the Synopsys DesignWare
PCI core. This patch adds the driver support for Meson PCIe controller.

Link: https://lore.kernel.org/linux-pci/20181218224708.GB22610@google.com/Signed-off-by: Yue Wang <yue.wang@amlogic.com>
Signed-off-by: Hanjie Lin <hanjie.lin@amlogic.com>
[lorenzo.pieralisi@arm.com: updated coding/comment style]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

The Amlogic Meson PCIe host controller is based on the Synopsys DesignWare
PCI core. This patch adds documentation for the DT bindings in Meson PCIe
controller.
Signed-off-by: Yue Wang <yue.wang@amlogic.com>
Signed-off-by: Hanjie Lin <hanjie.lin@amlogic.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>

The "num-lanes" property for PCIe is not used, remove it.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

The "num-lanes" property for PCIe is not used, remove it.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

The "num-lanes" property is not used, remove it.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

The "lane" variant in struct mtk_pcie_port is not used, remove it.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

Jianguo Sun's email address reported in MAINTAINERS is not active any
longer, remove it from the DWC HiSilicon STB entry.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>

The DWC PCIe core contains various separate register spaces: DBI, DBI2,
ATU, DMA, etc. The relationship between the addresses of these register
spaces is entirely determined by the implementation of the IP block, not
by the IP block design itself. Hence, the DWC driver must not make
assumptions that one register space can be accessed at a fixed offset from
any other register space. To avoid such assumptions, introduce an
explicit/separate register pointer for the ATU register space. In
particular, the current assumption is not valid for NVIDIA's T194 SoC.

The ATU register space is only used on systems that require unrolled ATU
access. This property is detected at run-time for host controllers, and
when this is detected, this patch provides a default value for atu_base
that matches the previous assumption re: register layout. An alternative
would be to update all drivers for HW that requires unrolled access to
explicitly set atu_base. However, it's hard to tell which drivers would
require atu_base to be set. The unrolled property is not detected for
endpoint systems, and so any endpoint driver that requires unrolled access
must explicitly set the iatu_unroll_enabled flag (none do at present), and
so a check is added to require the driver to also set atu_base while at
it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>

Enable PCI suspend/resume support on imx6sx SOCs. This is similar to
imx7d with a few differences:

* The PM_Turn_Off bit is exposed through an IOMUX GPR, like all other
pcie control bits on 6sx.
* The pcie_inbound_axi clk needs to be turned off in suspend. On resume
it is restored via resume -> deassert_core_reset -> enable_ref_clk.

Most of the resume logic is shared with the initial reset after probe.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>

Add support for the gpio reset signal binding as described in the
designware-pcie.txt DT binding document. Both the documented
'reset-gpio' property name and the more standard 'reset-gpios' name are
supported.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>

The IMX6 PCI-e host driver also supports the IMX7d. However, the
Kconfig dependencies of the driver prevented it from being enabled
unless the kernel was built with both IMX6 and IMX7 support.

It works fine to build with only IMX7 support enabled therefore
adjust the Kconfig entry to allow this configuration.
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>

Constify driver data since they do not get changed at runtime.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

On some chips the PCIe and PCIE_PHY blocks are in separate power domains
which can be power-gated independently. The PCI driver needs to handle
this by keeping both domain active.

This is intended for imx6sx where PCIe is in DISPLAY and PCIE_PHY in
its own domain. Defining the DISPLAY domain requires a way for PCIe to
keep it active or it will break when displays are off.

The power-domains on imx6sx are meant to look like this:
	power-domains = <&pd_disp>, <&pd_pci>;
	power-domain-names = "pcie", "pcie_phy";
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>

Synopsys USB 3.x host HAPS platform has a class code of
PCI_CLASS_SERIAL_USB_XHCI, and xhci driver can claim it.  However, these
devices should use dwc3-haps driver.  Change these devices' class code to
PCI_CLASS_SERIAL_USB_DEVICE to prevent the xhci-pci driver from claiming
them.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Move Synopsys HAPS platform device IDs to pci_ids.h so that both
drivers/pci/quirks.c and dwc3-haps driver can reference these IDs.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>

ASPM does not make use of the children or link LIST_HEADs declared in
struct pcie_link_state and defined in alloc_pcie_link_state().  Therefore,
remove these lists.

No functional change intended.
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

MRPC normal mode requires the host to read the MRPC command status and
output data from BAR.  This results in high latency responses from the
Memory Read TLP and potential Completion Timeout (CTO).

Add support for MRPC DMA mode, including related macro definitions and data
structures and code to:

  * Retrieve MRPC DMA mode version from adapter firmware
  * Allocate DMA buffer, register ISR, and enable DMA during init
  * Check MRPC execution status and get execution results from DMA buffer
  * Release DMA buffer and disable DMA function when unloading module

MRPC DMA mode is a new feature of firmware, and the driver will fall back
to MRPC normal mode if there is no support in the legacy firmware.

Add a module parameter, "use_dma_mrpc", to select between MRPC DMA mode and
MRPC normal mode.  Since the driver automatically detects DMA support in
the firmware, this parameter is just for debugging and testing.

Include <linux/io-64-nonatomic-lo-hi.h> so that readq/writeq is replaced by
two readl/writel on systems that do not support it.
Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
[bhelgaas: changelog, simplify dma_ver check]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>

The MRPC Input buffer is mostly memory without any side effects, so we
can improve the access time by enabling write combining on this region
of the BAR.

In a few places, we still need to flush the WC buffer.  To do this, we
simply read from the Outbound Doorbell register because reads to this
register are processed by low latency hardware.
Signed-off-by: Kelvin Cao <kelvin.cao@microchip.com>
Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>

In the ioctl_event_ctl() SWITCHTEC_IOCTL_EVENT_IDX_ALL case, we call
event_ctl() several times with the same "ctl" struct.  Each call clobbers
ctl.flags, which leads to the problem that we may not actually enable or
disable all events as the user requested.

Preserve the event flag value with a temporary variable.

Fixes: 52eabba5 ("switchtec: Add IOCTLs to the Switchtec driver")
Signed-off-by: Joey Zhang <joey.zhang@microchip.com>
Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>

Switchtec hardware supports 64-bit DMA, so set the correct DMA mask.  This
allows the CMA to allocate larger buffers for memory windows.
Signed-off-by: Boris Glimcher <Boris.Glimcher@emc.com>
Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>

After submitting a Firmware Download MRPC command, Switchtec firmware will
delay Management EP BAR MemRd TLP responses by more than 10ms.  This is a
firmware limitation.  Delayed MemRd completions are a problem for systems
with a low Completion Timeout (CTO).

The current driver checks the MRPC status immediately after submitting an
MRPC command, which results in a delayed MemRd completion that may cause a
Completion Timeout.

Remove the immediate status check and rely on the check after receiving an
interrupt or timing out.

This is only a software workaround to the READ issue and a proper fix of
this should be done in firmware.

Fixes: 080b47de ("MicroSemi Switchtec management interface driver")
Signed-off-by: Kelvin Cao <kelvin.cao@microchip.com>
Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>

a9c8088c ("i2c: i801: Don't restore config registers on runtime PM")
nullified the runtime PM suspend/resume callback pointers while keeping the
runtime PM enabled.

This caused the SMBus PCI device to stay in D0 with
/sys/devices/.../power/runtime_status showing "error" when the runtime PM
framework attempted to autosuspend the device.  This is due to PCI bus
runtime PM, which checks for driver runtime PM callbacks and returns
-ENOSYS if they are not set.

Since i2c-i801.c doesn't need to do anything device-specific for runtime
PM, Jean Delvare proposed this be fixed in the PCI core rather than adding
dummy runtime PM callback functions in the PCI drivers.

Change pci_pm_runtime_suspend()/pci_pm_runtime_resume() so they allow
changing the PCI device power state during runtime PM transitions even if
the driver supplies no runtime PM callbacks.

This fixes the runtime PM regression on i2c-i801.c.

It is not obvious why the code previously required the runtime PM
callbacks.  The test has been there since the code was introduced by
6cbf8214 ("PCI PM: Run-time callbacks for PCI bus type").

On the other hand, a similar change was done to generic runtime PM
callbacks in 05aa55dd ("PM / Runtime: Lenient generic runtime pm
callbacks").

Fixes: a9c8088c ("i2c: i801: Don't restore config registers on runtime PM")
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: stable@vger.kernel.org	# v4.18+

Fix typos, spellos, and grammar in p2pdma.rst and p2pdma.c.

Fix return value(s) in function pci_p2pmem_alloc_sgl().
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Logan Gunthorpe <logang@deltatee.com>
Cc: Jonathan Corbet <corbet@lwn.net>