There are much pci compatible with version on existing platforms.
To stop putting version numbers in device tree later, we add a
generic compatible 'fsl,qoriq-pcie'.
The version number is readable directly from a register.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

Add elo3-dma-2.dtsi to support the third DMA controller.
This is used on T2080, T4240, B4860, etc.

FSL MPIC v4.3 adds a new discontiguous address range for internal interrupts,
e.g. internal interrupt 0 is at offset 0x200 and thus interrupt number is:
0x200 >> 5 = 16 in the device tree.  DMA controller 3 channel 0 internal
interrupt 240 is at offset 0x3a00, and thus the corresponding interrupt
number is: 0x3a00 >> 5 = 464, it's similar for other 7 interrupt numbers
of DMA 3 channels.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Hongbo Zhang <hongbo.zhang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

On Freescale e6500 cores EPCR[DGTMI] controls whether guest supervisor
state can execute TLB management instructions. If EPCR[DGTMI]=0
tlbwe and tlbilx are allowed to execute normally in the guest state.

A hypervisor may choose to virtualize TLB1 and for this purpose it
may use IPROT to protect the entries for being invalidated by the
guest. However, because tlbwe and tlbilx execution in the guest state
are sharing the same bit, it is not possible to have a scenario where
tlbwe is allowed to be executed in guest state and tlbilx traps. When
guest TLB management instructions are allowed to be executed in guest
state the guest cannot use tlbilx to invalidate TLB1 guest entries.

Linux is using tlbilx in the boot code to invalidate the temporary
entries it creates when initializing the MMU. The patch is replacing
the usage of tlbilx in initialization code with tlbwe with VALID bit
cleared.

Linux is also using tlbilx in other contexts (like huge pages or
indirect entries) but removing the tlbilx from the initialization code
offers the possibility to have scenarios under hypervisor which are
not using huge pages or indirect entries.
Signed-off-by: Diana Craciun <Diana.Craciun@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

It was branching to the cleanup part of the non-bolted handler,
which would have been bad if there were any chips with tlbsrx.
that use the bolted handler.
Signed-off-by: Scott Wood <scottwood@freescale.com>

As of commit b81f18e5 ("powerpc/boot:
Only build board support files when required.") the two defconfigs
ep88xc_defconfig and storcenter_defconfig would fail final link as
follows:

  WRAP    arch/powerpc/boot/dtbImage.ep88xc
arch/powerpc/boot/wrapper.a(mpc8xx.o): In function `mpc885_get_clock':
arch/powerpc/boot/mpc8xx.c:30: undefined reference to `fsl_get_immr'
make[1]: *** [arch/powerpc/boot/dtbImage.ep88xc] Error 1

 ...and...

  WRAP    arch/powerpc/boot/cuImage.storcenter
arch/powerpc/boot/cuboot-pq2.o: In function `pq2_platform_fixups':
cuboot-pq2.c:(.text+0x324): undefined reference to `fsl_get_immr'
make[1]: *** [arch/powerpc/boot/cuImage.storcenter] Error 1

We need the fsl-soc board files built for these two platforms.

Cc: Tony Breeds <tony@bakeyournoodle.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fixes: b81f18e5 ("powerpc/boot: Only build board support files when required.")
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

On P1020, P1021, P1022, and P1023, eLBC event interrupts are routed
to internal interrupt 3 while ELBC error interrupts are routed to
internal interrupt 0.  We need to call request_irq for each.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
[scottwood@freescale.com: reworded commit message and fixed author]
Signed-off-by: Scott Wood <scottwood@freescale.com>

P1020, P1021, P1022, P1023 when the lbc get error, the error
interrupt will be triggered. The corresponding interrupt is
internal IRQ0. So system have to process the lbc IRQ0 interrupt.

The corresponding lbc general interrupt is internal IRQ3.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
[scottwood@freescale.com: bracketed individual list elements]
Signed-off-by: Scott Wood <scottwood@freescale.com>

Add support for the Motorola/Emerson MVME5100 Single Board Computer.

The MVME5100 is a 6U form factor VME64 computer with:

	- A single MPC7410 or MPC750 CPU
	- A HAWK Processor Host Bridge (CPU to PCI) and
	  MultiProcessor Interrupt Controller (MPIC)
	- Up to 500Mb of onboard memory
	- A M48T37 Real Time Clock (RTC) and Non-Volatile Memory chip
	- Two 16550 compatible UARTS
	- Two Intel E100 Fast Ethernets
	- Two PCI Mezzanine Card (PMC) Slots
	- PPCBug Firmware

The HAWK PHB/MPIC is compatible with the MPC10x devices.

There is no onboard disk support. This is usually provided by installing a PMC
in first PMC slot.

This patch revives the board support, it was present in early 2.6
series kernels. The board support in those days was by Matt Porter of
MontaVista Software.

CSC Australia has around 31 of these boards in service. The kernel in use
for the boards is based on 2.6.31. The boards are operated without disks
from a file server.

This patch is based on linux-3.13-rc2 and has been boot tested.

Only boards with 512 Mb of memory are known to work.
Signed-off-by: Stephen Chivers <schivers@csc.com>
Tested-by: Alessio Igor Bogani <alessio.bogani@elettra.eu>
Signed-off-by: Scott Wood <scottwood@freescale.com>

This keeps usage coordinated for hugetlb and indirect entries, which
should make entry selection more predictable and probably improve overall
performance when mixing the two.
Signed-off-by: Scott Wood <scottwood@freescale.com>

There are a few things that make the existing hw tablewalk handlers
unsuitable for e6500:

 - Indirect entries go in TLB1 (though the resulting direct entries go in
   TLB0).

 - It has threads, but no "tlbsrx." -- so we need a spinlock and
   a normal "tlbsx".  Because we need this lock, hardware tablewalk
   is mandatory on e6500 unless we want to add spinlock+tlbsx to
   the normal bolted TLB miss handler.

 - TLB1 has no HES (nor next-victim hint) so we need software round robin
   (TODO: integrate this round robin data with hugetlb/KVM)

 - The existing tablewalk handlers map half of a page table at a time,
   because IBM hardware has a fixed 1MiB indirect page size.  e6500
   has variable size indirect entries, with a minimum of 2MiB.
   So we can't do the half-page indirect mapping, and even if we
   could it would be less efficient than mapping the full page.

 - Like on e5500, the linear mapping is bolted, so we don't need the
   overhead of supporting nested tlb misses.

Note that hardware tablewalk does not work in rev1 of e6500.
We do not expect to support e6500 rev1 in mainline Linux.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Mihai Caraman <mihai.caraman@freescale.com>

There is no barrier between something like ioremap() writing to
a PTE, and returning the value to a caller that may then store the
pointer in a place that is visible to other CPUs.  Such callers
generally don't perform barriers of their own.

Even if callers of ioremap() and similar things did use barriers,
the most logical choise would be smp_wmb(), which is not
architecturally sufficient when BookE hardware tablewalk is used.  A
full sync is specified by the architecture.

For userspace mappings, OTOH, we generally already have an lwsync due
to locking, and if we occasionally take a spurious fault due to not
having a full sync with hardware tablewalk, it will not be fatal
because we will retry rather than oops.
Signed-off-by: Scott Wood <scottwood@freescale.com>

The RELOCATABLE is more flexible and without any alignment restriction.
And it is a superset of DYNAMIC_MEMSTART. So use it by default for
a kdump kernel.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

When booting above the 64M for a secondary cpu, we also face the
same issue as the boot cpu that the PAGE_OFFSET map two different
physical address for the init tlb and the final map. So we have to use
switch_to_as1/restore_to_as0 between the conversion of these two
maps. When restoring to as0 for a secondary cpu, we only need to
return to the caller. So add a new parameter for function
restore_to_as0 for this purpose.

Use LOAD_REG_ADDR_PIC to get the address of variables which may
be used before we set the final map in cams for the secondary cpu.
Move the setting of cams a bit earlier in order to avoid the
unnecessary using of LOAD_REG_ADDR_PIC.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

This is always true for a non-relocatable kernel. Otherwise the kernel
would get stuck. But for a relocatable kernel, it seems a little
complicated. When booting a relocatable kernel, we just align the
kernel start addr to 64M and map the PAGE_OFFSET from there. The
relocation will base on this virtual address. But if this address
is not the same as the memstart_addr, we will have to change the
map of PAGE_OFFSET to the real memstart_addr and do another relocation
again.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
[scottwood@freescale.com: make offset long and non-negative in simple case]
Signed-off-by: Scott Wood <scottwood@freescale.com>

Introduce this function so we can set both the physical and virtual
address for the map in cams. This will be used by the relocation code.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

For a relocatable kernel since it can be loaded at any place, there
is no any relation between the kernel start addr and the memstart_addr.
So we can't calculate the memstart_addr from kernel start addr. And
also we can't wait to do the relocation after we get the real
memstart_addr from device tree because it is so late. So introduce
a new function we can use to get the first memblock address and size
in a very early stage (before machine_init).
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

We use the tlb1 entries to map low mem to the kernel space. In the
current code, it assumes that the first tlb entry would cover the
kernel image. But this is not true for some special cases, such as
when we run a relocatable kernel above the 64M or set
CONFIG_KERNEL_START above 64M. So we choose to switch to address
space 1 before setting these tlb entries.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

This is based on the codes in the head_44x.S. The difference is that
the init tlb size we used is 64M. With this patch we can only load the
kernel at address between memstart_addr ~ memstart_addr + 64M. We will
fix this restriction in the following patches.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

This is used to get the address of a variable when the kernel is not
running at the linked or relocated address.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

Move the codes which translate a effective address to physical address
to a separate function. So it can be reused by other code.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

The e500v1 doesn't implement the MAS7, so we should avoid to access
this register on that implementations. In the current kernel, the
access to MAS7 are protected by either CONFIG_PHYS_64BIT or
MMU_FTR_BIG_PHYS. Since some code are executed before the code
patching, we have to use CONFIG_PHYS_64BIT in these cases.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

In some cases tmp_sec may be greater than ticks, because in the process
of calculation ticks and tmp_sec will be rounded.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

When the timer GTCCR toggle bit is inverted, we calculated the rest
of the time is not accurate. So we need to ignore this bit.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

Add an external interrupt for rtc node.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

RTC Hardware(ds3232) and rtc compatible string does not match.
Change "dallas,ds1339" to "dallas,ds3232".
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

ehv_bytechan is marked tristate but fails to build as a module:

drivers/tty/ehv_bytechan.c:363:1: error: type defaults to ‘int’ in declaration of ‘console_initcall’ [-Werror=implicit-int]

It doesn't make much sense for a console driver to be built as
a module, so change it to a bool.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>

Add a sys interface to enable/diable pw20 state or altivec idle, and
control the wait entry time.

Enable/Disable interface:
    0, disable. 1, enable.
    /sys/devices/system/cpu/cpuX/pw20_state
    /sys/devices/system/cpu/cpuX/altivec_idle

Set wait time interface:(Nanosecond)
    /sys/devices/system/cpu/cpuX/pw20_wait_time
    /sys/devices/system/cpu/cpuX/altivec_idle_wait_time
Example: Base on TBfreq is 41MHZ.
    1~48(ns): TB[63]
    49~97(ns): TB[62]
    98~195(ns): TB[61]
    196~390(ns): TB[60]
    391~780(ns): TB[59]
    781~1560(ns): TB[58]
    ...
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
[scottwood@freescale.com: change ifdef]
Signed-off-by: Scott Wood <scottwood@freescale.com>

Using hardware features make core automatically enter PW20 state.
Set a TB count to hardware, the effective count begins when PW10
is entered. When the effective period has expired, the core will
proceed from PW10 to PW20 if no exit conditions have occurred during
the period.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

Each core's AltiVec unit may be placed into a power savings mode
by turning off power to the unit. Core hardware will automatically
power down the AltiVec unit after no AltiVec instructions have
executed in N cycles. The AltiVec power-control is triggered by hardware.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

E6500 PVR and SPRN_PWRMGTCR0 will be used in subsequent pw20/altivec
idle patches.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

Moved the following functions out of the __init section:

   arch/powerpc/sysdev/fsl_pci.c      : fsl_add_bridge()
   arch/powerpc/sysdev/indirect_pci.c : setup_indirect_pci()

Those are referenced by arch/powerpc/sysdev/fsl_pci.c : fsl_pci_probe() when
compiling for Book E support.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: Scott Wood <scottwood@freescale.com>

It is not correct according to p1010rdb-pa user guide.
So modify it.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

On PPC_8xx, CRC32_SLICEBY4 is more efficient (almost twice) than CRC32_SLICEBY8,
as shown below:

With CRC32_SLICEBY8:
[    1.109204] crc32: CRC_LE_BITS = 64, CRC_BE BITS = 64
[    1.114401] crc32: self tests passed, processed 225944 bytes in 15118910 nsec
[    1.130655] crc32c: CRC_LE_BITS = 64
[    1.134235] crc32c: self tests passed, processed 225944 bytes in 4479879 nsec

With CRC32_SLICEBY4:
[    1.097129] crc32: CRC_LE_BITS = 32, CRC_BE BITS = 32
[    1.101878] crc32: self tests passed, processed 225944 bytes in 8616242 nsec
[    1.116298] crc32c: CRC_LE_BITS = 32
[    1.119607] crc32c: self tests passed, processed 225944 bytes in 3289576 nsec
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>

TWR-P1025 Overview
 -----------------
 512Mbyte DDR3 (on board DDR)
 64MB Nor Flash
 eTSEC1: Connected to RGMII PHY AR8035
 eTSEC3: Connected to RGMII PHY AR8035
 Two USB2.0 Type A
 One microSD Card slot
 One mini-PCIe slot
 One mini-USB TypeB dual UART
Signed-off-by: Michael Johnston <michael.johnston@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
[scottwood@freescale.com: use pr_info rather than KERN_INFO]
Signed-off-by: Scott Wood <scottwood@freescale.com>

Define a QE init function in common file, and avoid
the same codes being duplicated in board files.
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

mpc85xx_smp_defconfig and mpc85xx_defconfig already have CONFIG_P1023RDS=y.
Merge CONFIG_P1023RDB=y and other relevant configurations into
mpc85xx_smp_defconfig and mpc85_defconfig.
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

This fixes a build break that was probably introduced with the removal
of -Wa,-me500 (commit f49596a4), where
the assembler refuses to recognize SPRG4-7 with a generic PPC target.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Dongsheng Wang <dongsheng.wang@freescale.com>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Reviewed-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Tested-by: Wang Dongsheng <dongsheng.wang@freescale.com>

It makes no sense to initialize the mpic ipi for the SoC which has
doorbell support. So set the smp_85xx_ops.probe to NULL for this
case. Since the smp_85xx_ops.probe is also used in function
smp_85xx_setup_cpu() to check if we need to invoke
mpic_setup_this_cpu(), we introduce a new setup_cpu function
smp_85xx_basic_setup() to remove this dependency.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

P1010rdb-pa and p1010rdb-pb have different mtd of nand.
So update dts to adapt to both p1010rdb-pa and p1010rdb-pb.

Move the nand-mtd from p1010rdb.dtsi to p1010rdb-pa*.dts.
Remove nand-mtd for p1010rdb-pb, whick will use mtdparts
from u-boot instead of nand-mtd in device tree.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

P1010rdb-pa and p1010rdb-pb have different phy interrupts.
So update dts to adapt to both p1010rdb-pa and p1010rdb-pb.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>