Use Complete data type declaration of 'sel' in ti_abb_set_voltage_sel().
Fix spelling of 'are'nt' in comments.
Signed-off-by: Zhang Jiaming <jiaming@nfschina.com>
Link: https://lore.kernel.org/r/20220705071445.21124-1-jiaming@nfschina.comSigned-off-by: Mark Brown <broonie@kernel.org>

max597x is hot swap controller.
This regulator driver controls the same & also configures fault
protection features supported by the chip.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Marcello Sylvester Bauer <sylv@sylv.io>
Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
Link: https://lore.kernel.org/r/20220705122244.472894-4-Naresh.Solanki@9elements.comSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series from Stephan Gerhold <stephan.gerhold@kernkonzept.com>:

Fix the voltage range for the pm8916_pldo in the qcom_smd-regulator
driver and add definitions for the regulators available in PM8909.

In scmi_regulator_probe(), of_find_node_by_name() will decrease
the refcount of its first argument and we need a of_node_get()
to keep reference balance.
Signed-off-by: Liang He <windhl@126.com>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20220622034816.4094043-1-windhl@126.comSigned-off-by: Mark Brown <broonie@kernel.org>

The set of regulators available in the PM8909 PMIC is similar to PM8916
which is already supported by the driver. s3, s4 and l16 are missing.
However, probing the SPMI hardware identification registers using the
qcom_spmi-regulator driver reveals that the regulators in PM8909 are
actually some kind of mixture between PM8916 and PM8226:

  - ult_lo_smps (= pm8916_buck_lvo_smps): s1
  - ult_ho_smps (= pm8916_buck_hvo_smps): s2
  - ult_nldo (= pm8916_nldo): l1, l2, l3, l10
  - ult_pldo (= pm8916_pldo): l4, l8, l9, l12-l15, l17, l18
  - pldo (= pm8226_pldo): l5, l6, l7, l11

Use this mapping to add the rpm_regulator_data for PM8909 by reusing
the existing regulator definitions.
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Link: https://lore.kernel.org/r/20220623094614.1410180-4-stephan.gerhold@kernkonzept.comSigned-off-by: Mark Brown <broonie@kernel.org>

Document the "qcom,rpm-pm8909-regulators" compatible for describing
the regulators available in the PM8909 PMIC (controlled via the RPM
firmware).

PM8909 is very similar to the existing PM8916 but lacks 3 of the
regulators (s3, s4 and l16).
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220623094614.1410180-3-stephan.gerhold@kernkonzept.comSigned-off-by: Mark Brown <broonie@kernel.org>

The PM8916 device specification [1] documents a programmable range of
1.75V to 3.337V with 12.5mV steps for the PMOS LDOs in PM8916. This
range is also used when controlling the regulator directly using the
qcom_spmi-regulator driver ("ult_pldo" there).

However, for some reason the qcom_smd-regulator driver allows a much
larger range for the same hardware component. This could be simply a
typo, since the start of the range is essentially just missing a '1'.

In practice this does not cause any major problems, since the driver
just sends the actual voltage to the RPM firmware instead of making use
of the incorrect voltage selector. Still, having the wrong range there
is confusing and prevents the regulator core from validating requests
correctly.

[1]: https://developer.qualcomm.com/download/sd410/pm8916pm8916-1-power-management-ic-device-specification.pdf

Fixes: 57d65676 ("regulator: qcom-smd: Add PM8916 support")
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Link: https://lore.kernel.org/r/20220623094614.1410180-2-stephan.gerhold@kernkonzept.comSigned-off-by: Mark Brown <broonie@kernel.org>

'platform_device_id' struct is defined in 'mod_devicetable.h'.
Even 'of.h' also includes this header usage. The 'of.h' cannot be removed
due to 'of_match_ptr' function.
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/1656466861-7737-2-git-send-email-u0084500@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

From the common binding, 'enable-gpio' or 'enable-gpios' are all well
for external 'enable' gpio.

'gpiod_get_from_of_node' only parse the 'enable' property, it need to
add the gpio suffix. It's more convenient to use fwnode_gpiod_get_index.
Although fwnode parsing is not preferred, but 'of_parse_cb' already can
guarantee the callback will only be used by regulator of_node parsing.
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/1656466861-7737-1-git-send-email-u0084500@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

document n_ramp_values field at struct regulator_desc, in order
to solve this warning:

	include/linux/regulator/driver.h:434: warning: Function parameter or member 'n_ramp_values' not described in 'regulator_desc'
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Link: https://lore.kernel.org/r/15efc16e878aa327aa2769023bcdf959a795f41d.1656409369.git.mchehab@kernel.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Add mt6370 DisplayBias and VibLDO support.
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/20220623115631.22209-10-peterwu.pub@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add RT5120 PMIC regulator support.

It integrates 4 buck convertes, 1 LDO voltage regulator, 1 external
enable signal to control the external power source.
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/1655892104-10874-4-git-send-email-u0084500@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

backlight_properties.fb_blank is deprecated. The states it represents
are handled by other properties; but instead of accessing those
properties directly, drivers should use the helpers provided by
backlight.h.

Instead of retrieving the backlight brightness in struct
backlight_properties manually, and then checking whether the backlight
should be on at all, use backlight_get_brightness() which does all
this and insulates this from future changes.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220607185304.1128962-1-steve@sk2.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Add the get_voltage OP to MP5496 ops using the generic rpm_reg_get_voltage.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Link: https://lore.kernel.org/r/20220604193300.125758-1-robimarko@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

Currently set MP5496 Buck and LDO ranges dont match its datasheet[1].
According to the datasheet:
Buck range is 0.6-2.1875V with a 12.5mV step
LDO range is 0.8-3.975V with a 25mV step.

So, correct the ranges according to the datasheet[1].

[1] https://www.monolithicpower.com/en/documentview/productdocument/index/version/2/document_type/Datasheet/lang/en/sku/MP5496GR/document_id/6906/Signed-off-by: Robert Marko <robimarko@gmail.com>
Link: https://lore.kernel.org/r/20220604193300.125758-2-robimarko@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

Driver does not seem to utilize anything from the kernel.h, compiles
and works fine for me without it.

So remove kernel.h include as it pulls in a lot of unused stuff.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Cc: christophe.jaillet@wanadoo.fr
Link: https://lore.kernel.org/r/20220607124759.775133-1-robimarko@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

Convert the pwm-regulator binding to DT schema format.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220606184310.1057797-1-robh@kernel.orgSigned-off-by: Mark Brown <broonie@kernel.org>

If the node for the match name cannot be found, 'of_regulator_match' will
returns init_data as NULL for this regulator.

Add the check for the init_data. If it's NULL, make 'rt5190a_of_parse_cb'
function directly return.
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/1654148646-12182-1-git-send-email-u0084500@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

MP5496 is the updated version of MP5416 with the only difference being
that now all Buck regulators have the same 0.6-2.1875V range with a 12.5mV
step.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Acked-by: Saravanan Sekar <sravanhome@gmail.com>
Link: https://lore.kernel.org/r/20220604145816.47576-4-robimarko@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

In preparation for adding support for MP5496 which slightly differs from
MP5416 convert the driver to use OF match data instead of always using the
MP5416 regulator_desc for regulator registration.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Acked-by: Saravanan Sekar <sravanhome@gmail.com>
Link: https://lore.kernel.org/r/20220604145816.47576-3-robimarko@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

Sort the header include list alphabetically.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Link: https://lore.kernel.org/r/20220604145816.47576-2-robimarko@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

MP5496 is the updated version of MP5416 with the only difference being
that now all Buck regulators have the same 0.6-2.1875V range with a 12.5mV
step.

Since there is no way to differentiate them other than using compatibles,
add compatible for the MP5496.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Link: https://lore.kernel.org/r/20220604145816.47576-1-robimarko@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

Pull file descriptor fix from Al Viro:
 "Fix for breakage in #work.fd this window"

* tag 'pull-work.fd-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fix the breakage in close_fd_get_file() calling conventions change

Pull mm hotfixes from Andrew Morton:
 "Fixups for various recently-added and longer-term issues and a few
  minor tweaks:

   - fixes for material merged during this merge window

   - cc:stable fixes for more longstanding issues

   - minor mailmap and MAINTAINERS updates"

* tag 'mm-hotfixes-stable-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
  mm/oom_kill.c: fix vm_oom_kill_table[] ifdeffery
  x86/kexec: fix memory leak of elf header buffer
  mm/memremap: fix missing call to untrack_pfn() in pagemap_range()
  mm: page_isolation: use compound_nr() correctly in isolate_single_pageblock()
  mm: hugetlb_vmemmap: fix CONFIG_HUGETLB_PAGE_FREE_VMEMMAP_DEFAULT_ON
  MAINTAINERS: add maintainer information for z3fold
  mailmap: update Josh Poimboeuf's email

Pull delay-accounting update from Andrew Morton:
 "A single featurette for delay accounting.

  Delayed a bit because, unusually, it had dependencies on both the
  mm-stable and mm-nonmm-stable queues"

* tag 'mm-nonmm-stable-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
  delayacct: track delays from write-protect copy

The bluetooth code uses our bitmap infrastructure for the two bits (!)
of connection setup flags, and in the process causes odd problems when
it converts between a bitmap and just the regular values of said bits.

It's completely pointless to do things like bitmap_to_arr32() to convert
a bitmap into a u32.  It shoudln't have been a bitmap in the first
place.  The reason to use bitmaps is if you have arbitrary number of
bits you want to manage (not two!), or if you rely on the atomicity
guarantees of the bitmap setting and clearing.

The code could use an "atomic_t" and use "atomic_or/andnot()" to set and
clear the bit values, but considering that it then copies the bitmaps
around with "bitmap_to_arr32()" and friends, there clearly cannot be a
lot of atomicity requirements.

So just use a regular integer.

In the process, this avoids the warnings about erroneous use of
bitmap_from_u64() which were triggered on 32-bit architectures when
conversion from a u64 would access two words (and, surprise, surprise,
only one word is needed - and indeed overkill - for a 2-bit bitmap).

That was always problematic, but the compiler seems to notice it and
warn about the invalid pattern only after commit 0a97953f ("lib: add
bitmap_{from,to}_arr64") changed the exact implementation details of
'bitmap_from_u64()', as reported by Sudip Mukherjee and Stephen Rothwell.

Fixes: fe92ee64 ("Bluetooth: hci_core: Rework hci_conn_params flags")
Link: https://lore.kernel.org/all/YpyJ9qTNHJzz0FHY@debian/
Link: https://lore.kernel.org/all/20220606080631.0c3014f2@canb.auug.org.au/
Link: https://lore.kernel.org/all/20220605162537.1604762-1-yury.norov@gmail.com/Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

It used to grab an extra reference to struct file rather than
just transferring to caller the one it had removed from descriptor
table.  New variant doesn't, and callers need to be adjusted.

Reported-and-tested-by: syzbot+47dd250f527cb7bebf24@syzkaller.appspotmail.com
Fixes: 6319194e ("Unify the primitives for file descriptor closing")
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Pull x86 SGX fix from Thomas Gleixner:
 "A single fix for x86/SGX to prevent that memory which is allocated for
  an SGX enclave is accounted to the wrong memory control group"

* tag 'x86-urgent-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/sgx: Set active memcg prior to shmem allocation

Pull x86 mm cleanup from Thomas Gleixner:
 "Use PAGE_ALIGNED() instead of open coding it in the x86/mm code"

* tag 'x86-mm-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mm: Use PAGE_ALIGNED(x) instead of IS_ALIGNED(x, PAGE_SIZE)

Pull x86 microcode updates from Thomas Gleixner:

 - Disable late microcode loading by default. Unless the HW people get
   their act together and provide a required minimum version in the
   microcode header for making a halfways informed decision its just
   lottery and broken.

 - Warn and taint the kernel when microcode is loaded late

 - Remove the old unused microcode loader interface

 - Remove a redundant perf callback from the microcode loader

* tag 'x86-microcode-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/microcode: Remove unnecessary perf callback
  x86/microcode: Taint and warn on late loading
  x86/microcode: Default-disable late loading
  x86/microcode: Rip out the OLD_INTERFACE

Pull x86 cleanups from Thomas Gleixner:
 "A set of small x86 cleanups:

   - Remove unused headers in the IDT code

   - Kconfig indendation and comment fixes

   - Fix all 'the the' typos in one go instead of waiting for bots to
     fix one at a time"

* tag 'x86-cleanups-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86: Fix all occurences of the "the the" typo
  x86/idt: Remove unused headers
  x86/Kconfig: Fix indentation of arch/x86/Kconfig.debug
  x86/Kconfig: Fix indentation and add endif comments to arch/x86/Kconfig

Pull x86 boot update from Thomas Gleixner:
 "Use strlcpy() instead of strscpy() in arch_setup()"

* tag 'x86-boot-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/setup: Use strscpy() to replace deprecated strlcpy()

Pull clockevent/clocksource updates from Thomas Gleixner:

 - Device tree bindings for MT8186

 - Tell the kernel that the RISC-V SBI timer stops in deeper power
   states

 - Make device tree parsing in sp804 more robust

 - Dead code removal and tiny fixes here and there

 - Add the missing SPDX identifiers

* tag 'timers-core-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clocksource/drivers/oxnas-rps: Fix irq_of_parse_and_map() return value
  clocksource/drivers/timer-ti-dm: Remove unnecessary NULL check
  clocksource/drivers/timer-sun5i: Convert to SPDX identifier
  clocksource/drivers/timer-sun4i: Convert to SPDX identifier
  clocksource/drivers/pistachio: Convert to SPDX identifier
  clocksource/drivers/orion: Convert to SPDX identifier
  clocksource/drivers/lpc32xx: Convert to SPDX identifier
  clocksource/drivers/digicolor: Convert to SPDX identifier
  clocksource/drivers/armada-370-xp: Convert to SPDX identifier
  clocksource/drivers/mips-gic-timer: Convert to SPDX identifier
  clocksource/drivers/jcore: Convert to SPDX identifier
  clocksource/drivers/bcm_kona: Convert to SPDX identifier
  clocksource/drivers/sp804: Avoid error on multiple instances
  clocksource/drivers/riscv: Events are stopped during CPU suspend
  clocksource/drivers/ixp4xx: Drop boardfile probe path
  dt-bindings: timer: Add compatible for Mediatek MT8186

Pull scheduler fix from Thomas Gleixner:
 "Fix the fallout of sysctl code move which placed the init function
  wrong"

* tag 'sched-urgent-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/autogroup: Fix sysctl move

Pull perf fixes from Thomas Gleixner:

  - Make the ICL event constraints match reality

  - Remove a unused local variable

* tag 'perf-urgent-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/core: Remove unused local variable
  perf/x86/intel: Fix event constraints for ICL

Pull perf fixlet from Thomas Gleixner:
 "Trivial indentation fix in Kconfig"

* tag 'perf-core-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/Kconfig: Fix indentation in the Kconfig file

Pull objtool fixes from Thomas Gleixner:

 - Handle __ubsan_handle_builtin_unreachable() correctly and treat it as
   noreturn

 - Allow architectures to select uaccess validation

 - Use the non-instrumented bit test for test_cpu_has() to prevent
   escape from non-instrumentable regions

 - Use arch_ prefixed atomics for JUMP_LABEL=n builds to prevent escape
   from non-instrumentable regions

 - Mark a few tiny inline as __always_inline to prevent GCC from
   bringing them out of line and instrumenting them

 - Mark the empty stub context_tracking_enabled() as always inline as
   GCC brings them out of line and instruments the empty shell

 - Annotate ex_handler_msr_mce() as dead end

* tag 'objtool-urgent-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/extable: Annotate ex_handler_msr_mce() as a dead end
  context_tracking: Always inline empty stubs
  x86: Always inline on_thread_stack() and current_top_of_stack()
  jump_label,noinstr: Avoid instrumentation for JUMP_LABEL=n builds
  x86/cpu: Elide KCSAN for cpu_has() and friends
  objtool: Mark __ubsan_handle_builtin_unreachable() as noreturn
  objtool: Add CONFIG_HAVE_UACCESS_VALIDATION

Pull more SCSI updates from James Bottomley:
 "Mostly small bug fixes plus other trivial updates.

  The major change of note is moving ufs out of scsi and a minor update
  to lpfc vmid handling"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (24 commits)
  scsi: qla2xxx: Remove unused 'ql_dm_tgt_ex_pct' parameter
  scsi: qla2xxx: Remove setting of 'req' and 'rsp' parameters
  scsi: mpi3mr: Fix kernel-doc
  scsi: lpfc: Add support for ATTO Fibre Channel devices
  scsi: core: Return BLK_STS_TRANSPORT for ALUA transitioning
  scsi: sd_zbc: Prevent zone information memory leak
  scsi: sd: Fix potential NULL pointer dereference
  scsi: mpi3mr: Rework mrioc->bsg_device model to fix warnings
  scsi: myrb: Fix up null pointer access on myrb_cleanup()
  scsi: core: Unexport scsi_bus_type
  scsi: sd: Don't call blk_cleanup_disk() in sd_probe()
  scsi: ufs: ufshcd: Delete unnecessary NULL check
  scsi: isci: Fix typo in comment
  scsi: pmcraid: Fix typo in comment
  scsi: smartpqi: Fix typo in comment
  scsi: qedf: Fix typo in comment
  scsi: esas2r: Fix typo in comment
  scsi: storvsc: Fix typo in comment
  scsi: ufs: Split the drivers/scsi/ufs directory
  scsi: qla1280: Remove redundant variable
  ...

Pull hardware timestamping subsystem from Thierry Reding:
 "This contains the new HTE (hardware timestamping engine) subsystem
  that has been in the works for a couple of months now.

  The infrastructure provided allows for drivers to register as hardware
  timestamp providers, while consumers will be able to request events
  that they are interested in (such as GPIOs and IRQs) to be timestamped
  by the hardware providers.

  Note that this currently supports only one provider, but there seems
  to be enough interest in this functionality and we expect to see more
  drivers added once this is merged"

[ Linus Walleij mentions the Intel PMC in the Elkhart and Tiger Lake
  platforms as another future timestamp provider ]

* tag 'hte/for-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  dt-bindings: timestamp: Correct id path
  dt-bindings: Renamed hte directory to timestamp
  hte: Uninitialized variable in hte_ts_get()
  hte: Fix off by one in hte_push_ts_ns()
  hte: Fix possible use-after-free in tegra_hte_test_remove()
  hte: Remove unused including <linux/version.h>
  MAINTAINERS: Add HTE Subsystem
  hte: Add Tegra HTE test driver
  tools: gpio: Add new hardware clock type
  gpiolib: cdev: Add hardware timestamp clock type
  gpio: tegra186: Add HTE support
  gpiolib: Add HTE support
  dt-bindings: Add HTE bindings
  hte: Add Tegra194 HTE kernel provider
  drivers: Add hardware timestamp engine (HTE) subsystem
  Documentation: Add HTE subsystem guide