- 23 Mar, 2019 40 commits
-
-
Stuart Menefy authored
commit a5719a40 upstream. When a timer tick occurs and the clock is in one-shot mode, the timer needs to be stopped to prevent it triggering subsequent interrupts. Currently this code is in exynos4_mct_tick_clear(), but as it is only needed when an ISR occurs move it into exynos4_mct_tick_isr(), leaving exynos4_mct_tick_clear() just doing what its name suggests it should. Signed-off-by:
Stuart Menefy <stuart.menefy@mathembedded.com> Reviewed-by:
Krzysztof Kozlowski <krzk@kernel.org> Tested-by:
Marek Szyprowski <m.szyprowski@samsung.com> Cc: stable@vger.kernel.org # v4.3+ Signed-off-by:
Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Stuart Menefy authored
commit 28c4f730 upstream. The step values for some of the LDOs appears to be incorrect, resulting in incorrect voltages (or at least, ones which are different from the Samsung 3.4 vendor kernel). Signed-off-by:
Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by:
-
Mark Zhang authored
commit 0ab66b3c upstream. If regulator DT node doesn't exist, its of_parse_cb callback function isn't called. Then all values for DT properties are filled with zero. This leads to wrong register update for FPS and POK settings. Signed-off-by:
Jinyoung Park <jinyoungp@nvidia.com> Signed-off-by:
Mark Zhang <markz@nvidia.com> Signed-off-by:
-
Krzysztof Kozlowski authored
commit 56b5d4ea upstream. LDO35 uses 25 mV step, not 50 mV. Bucks 7 and 8 use 12.5 mV step instead of 6.25 mV. Wrong step caused over-voltage (LDO35) or under-voltage (buck7 and 8) if regulators were used (e.g. on Exynos5420 Arndale Octa board). Cc: <stable@vger.kernel.org> Fixes: cb74685e ("regulator: s2mps11: Add samsung s2mps11 regulator driver") Signed-off-by:
-
Andy Shevchenko authored
commit ef070b4e upstream. When the commit b6ced294 ("spi: pxa2xx: Switch to SPI core DMA mapping functionality") switches to SPI core provided DMA helpers, it missed to setup maximum supported DMA transfer length for the controller and thus users mistakenly try to send more data than supported with the following warning: ili9341 spi-PRP0001:01: DMA disabled for transfer length 153600 greater than 65536 Setup maximum supported DMA transfer length in order to make users know the limit. Fixes: b6ced294 ("spi: pxa2xx: Switch to SPI core DMA mapping functionality") Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
-
Vignesh R authored
commit 673c865e upstream. Commit 4dea6c9b ("spi: spi-ti-qspi: add mmap mode read support") has has got order of parameter wrong when calling regmap_update_bits() to select CS for mmap access. Mask and value arguments are interchanged. Code will work on a system with single slave, but fails when more than one CS is in use. Fix this by correcting the order of parameters when calling regmap_update_bits(). Fixes: 4dea6c9b ("spi: spi-ti-qspi: add mmap mode read support") Cc: stable@vger.kernel.org Signed-off-by:
Vignesh R <vigneshr@ti.com> Signed-off-by:
-
BOUGH CHEN authored
commit de0a0dec upstream. Now tuning reset will be done when the timing is MMC_TIMING_LEGACY/ MMC_TIMING_MMC_HS/MMC_TIMING_SD_HS. But for timing MMC_TIMING_MMC_HS, we can not do tuning reset, otherwise HS400 timing is not right. Here is the process of init HS400, first finish tuning in HS200 mode, then switch to HS mode and 8 bit DDR mode, finally switch to HS400 mode. If we do tuning reset in HS mode, this will cause HS400 mode lost the tuning setting, which will cause CRC error. Signed-off-by:
Haibo Chen <haibo.chen@nxp.com> Cc: stable@vger.kernel.org # v4.12+ Acked-by:
Adrian Hunter <adrian.hunter@intel.com> Fixes: d9370424 ("mmc: sdhci-esdhc-imx: reset tuning circuit when power on mmc card") Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Andy Shevchenko authored
commit f16eb8a4 upstream. If SSDT overlay is loaded via ConfigFS and then unloaded the device, we would like to have OF modalias for, already gone. Thus, acpi_get_name() returns no allocated buffer for such case and kernel crashes afterwards: ACPI: Host-directed Dynamic ACPI Table Unload ads7950 spi-PRP0001:00: Dropping the link to regulator.0 BUG: unable to handle kernel NULL pointer dereference at 0000000000000000 #PF error: [normal kernel read fault] PGD 80000000070d6067 P4D 80000000070d6067 PUD 70d0067 PMD 0 Oops: 0000 [#1] SMP PTI CPU: 0 PID: 40 Comm: kworker/u4:2 Not tainted 5.0.0+ #96 Hardware name: Intel Corporation Merrifield/BODEGA BAY, BIOS 542 2015.01.21:18.19.48 Workqueue: kacpi_hotplug acpi_device_del_work_fn RIP: 0010:create_of_modalias.isra.1+0x4c/0x150 Code: 00 00 48 89 44 24 18 31 c0 48 8d 54 24 08 48 c7 44 24 10 00 00 00 00 48 c7 44 24 08 ff ff ff ff e8 7a b0 03 00 48 8b 4c 24 10 <0f> b6 01 84 c0 74 27 48 c7 c7 00 09 f4 a5 0f b6 f0 8d 50 20 f6 04 RSP: 0000:ffffa51040297c10 EFLAGS: 00010246 RAX: 0000000000001001 RBX: 0000000000000785 RCX: 0000000000000000 RDX: 0000000000001001 RSI: 0000000000000286 RDI: ffffa2163dc042e0 RBP: ffffa216062b1196 R08: 0000000000001001 R09: ffffa21639873000 R10: ffffffffa606761d R11: 0000000000000001 R12: ffffa21639873218 R13: ffffa2163deb5060 R14: ffffa216063d1010 R15: 0000000000000000 FS: 0000000000000000(0000) GS:ffffa2163e000000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 0000000007114000 CR4: 00000000001006f0 Call Trace: __acpi_device_uevent_modalias+0xb0/0x100 spi_uevent+0xd/0x40 ... In order to fix above let create_of_modalias() check the status returned by acpi_get_name() and bail out in case of failure. Fixes: 8765c5ba ("ACPI / scan: Rework modalias creation when "compatible" is present") Link: https://bugzilla.kernel.org/show_bug.cgi?id=201381Reported-by:
Ferry Toth <fntoth@gmail.com> Tested-by: Ferry Toth<fntoth@gmail.com> Signed-off-by:
Mika Westerberg <mika.westerberg@linux.intel.com> Cc: 4.1+ <stable@vger.kernel.org> # 4.1+ Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Juergen Gross authored
commit 01bd2ac2 upstream. Commit f7c90c2a ("x86/xen: don't write ptes directly in 32-bit PV guests") introduced a regression for booting dom0 on huge systems with lots of RAM (in the TB range). Reason is that on those hosts the p2m list needs to be moved early in the boot process and this requires temporary page tables to be created. Said commit modified xen_set_pte_init() to use a hypercall for writing a PTE, but this requires the page table being in the direct mapped area, which is not the case for the temporary page tables used in xen_relocate_p2m(). As the page tables are completely written before being linked to the actual address space instead of set_pte() a plain write to memory can be used in xen_relocate_p2m(). Fixes: f7c90c2a ("x86/xen: don't write ptes directly in 32-bit PV guests") Cc: stable@vger.kernel.org Signed-off-by:
Juergen Gross <jgross@suse.com> Reviewed-by:
Jan Beulich <jbeulich@suse.com> Signed-off-by:
-
zhangyi (F) authored
commit e7f0c424 upstream. Commit d716ff71 ("tracing: Remove taking of trace_types_lock in pipe files") use the current tracer instead of the copy in tracing_open_pipe(), but it forget to remove the freeing sentence in the error path. There's an error path that can call kfree(iter->trace) after the iter->trace was assigned to tr->current_trace, which would be bad to free. Link: http://lkml.kernel.org/r/1550060946-45984-1-git-send-email-yi.zhang@huawei.com Cc: stable@vger.kernel.org Fixes: d716ff71 ("tracing: Remove taking of trace_types_lock in pipe files") Signed-off-by:
zhangyi (F) <yi.zhang@huawei.com> Signed-off-by:
Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by:
-
Tom Zanussi authored
commit 9f0bbf31 upstream. Because there may be random garbage beyond a string's null terminator, it's not correct to copy the the complete character array for use as a hist trigger key. This results in multiple histogram entries for the 'same' string key. So, in the case of a string key, use strncpy instead of memcpy to avoid copying in the extra bytes. Before, using the gdbus entries in the following hist trigger as an example: # echo 'hist:key=comm' > /sys/kernel/debug/tracing/events/sched/sched_waking/trigger # cat /sys/kernel/debug/tracing/events/sched/sched_waking/hist ... { comm: ImgDecoder #4 } hitcount: 203 { comm: gmain } hitcount: 213 { comm: gmain } hitcount: 216 { comm: StreamTrans #73 } hitcount: 221 { comm: mozStorage #3 } hitcount: 230 { comm: gdbus } hitcount: 233 { comm: StyleThread#5 } hitcount: 253 { comm: gdbus } hitcount: 256 { comm: gdbus } hitcount: 260 { comm: StyleThread#4 } hitcount: 271 ... # cat /sys/kernel/debug/tracing/events/sched/sched_waking/hist | egrep gdbus | wc -l 51 After: # cat /sys/kernel/debug/tracing/events/sched/sched_waking/hist | egrep gdbus | wc -l 1 Link: http://lkml.kernel.org/r/50c35ae1267d64eee975b8125e151e600071d4dc.1549309756.git.tom.zanussi@linux.intel.com Cc: Namhyung Kim <namhyung@kernel.org> Cc: stable@vger.kernel.org Fixes: 79e577cb ("tracing: Support string type key properly") Signed-off-by:
Tom Zanussi <tom.zanussi@linux.intel.com> Signed-off-by:
-
Pavel Shilovsky authored
commit 6dfbd846 upstream. When we have a READ lease for a file and have just issued a write operation to the server we need to purge the cache and set oplock/lease level to NONE to avoid reading stale data. Currently we do that only if a write operation succedeed thus not covering cases when a request was sent to the server but a negative error code was returned later for some other reasons (e.g. -EIOCBQUEUED or -EINTR). Fix this by turning off caching regardless of the error code being returned. The patches fixes generic tests 075 and 112 from the xfs-tests. Cc: <stable@vger.kernel.org> Signed-off-by:
Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by:
Steve French <stfrench@microsoft.com> Reviewed-by:
Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by:
-
Pavel Shilovsky authored
commit 7b9b9edb upstream. Currently on lease break the client sets a caching level twice: when oplock is detected and when oplock is processed. While the 1st attempt sets the level to the value provided by the server, the 2nd one resets the level to None unconditionally. This happens because the oplock/lease processing code was changed to avoid races between page cache flushes and oplock breaks. The commit c11f1df5 ("cifs: Wait for writebacks to complete before attempting write.") fixed the races for oplocks but didn't apply the same changes for leases resulting in overwriting the server granted value to None. Fix this by properly processing lease breaks. Signed-off-by:
-
Ard Biesheuvel authored
commit 969e2f59 upstream. Commit 5092fcf3 ("crypto: arm64/aes-ce-ccm: add non-SIMD generic fallback") introduced C fallback code to replace the NEON routines when invoked from a context where the NEON is not available (i.e., from the context of a softirq taken while the NEON is already being used in kernel process context) Fix two logical flaws in the MAC calculation of the associated data. Reported-by:
Eric Biggers <ebiggers@kernel.org> Fixes: 5092fcf3 ("crypto: arm64/aes-ce-ccm: add non-SIMD generic fallback") Cc: stable@vger.kernel.org Signed-off-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Ard Biesheuvel authored
commit eaf46edf upstream. The NEON MAC calculation routine fails to handle the case correctly where there is some data in the buffer, and the input fills it up exactly. In this case, we enter the loop at the end with w8 == 0, while a negative value is assumed, and so the loop carries on until the increment of the 32-bit counter wraps around, which is quite obviously wrong. So omit the loop altogether in this case, and exit right away. Reported-by:
-
Eric Biggers authored
commit eb5e6730 upstream. Instantiating "cryptd(crc32c)" causes a crypto self-test failure because the crypto_alloc_shash() in alg_test_crc32c() fails. This is because cryptd(crc32c) is an ahash algorithm, not a shash algorithm; so it can only be accessed through the ahash API, unlike shash algorithms which can be accessed through both the ahash and shash APIs. As the test is testing the shash descriptor format which is only applicable to shash algorithms, skip it for ahash algorithms. (Note that it's still important to fix crypto self-test failures even for weird algorithm instantiations like cryptd(crc32c) that no one would really use; in fips_enabled mode unprivileged users can use them to panic the kernel, and also they prevent treating a crypto self-test failure as a bug when fuzzing the kernel.) Fixes: 8e3ee85e ("crypto: crc32c - Test descriptor context format") Cc: stable@vger.kernel.org Signed-off-by:
Eric Biggers <ebiggers@google.com> Signed-off-by:
-
Eric Biggers authored
commit ba7d7433 upstream. Some algorithms have a ->setkey() method that is not atomic, in the sense that setting a key can fail after changes were already made to the tfm context. In this case, if a key was already set the tfm can end up in a state that corresponds to neither the old key nor the new key. It's not feasible to make all ->setkey() methods atomic, especially ones that have to key multiple sub-tfms. Therefore, make the crypto API set CRYPTO_TFM_NEED_KEY if ->setkey() fails and the algorithm requires a key, to prevent the tfm from being used until a new key is set. Note: we can't set CRYPTO_TFM_NEED_KEY for OPTIONAL_KEY algorithms, so ->setkey() for those must nevertheless be atomic. That's fine for now since only the crc32 and crc32c algorithms set OPTIONAL_KEY, and it's not intended that OPTIONAL_KEY be used much. [Cc stable mainly because when introducing the NEED_KEY flag I changed AF_ALG to rely on it; and unlike in-kernel crypto API users, AF_ALG previously didn't have this problem. So these "incompletely keyed" states became theoretically accessible via AF_ALG -- though, the opportunities for causing real mischief seem pretty limited.] Fixes: 9fa68f62 ("crypto: hash - prevent using keyed hashes without setting key") Cc: stable@vger.kernel.org Signed-off-by:
-
Ard Biesheuvel authored
commit d72b9d4a upstream. The SIMD routine ported from x86 used to have a special code path for inputs < 16 bytes, which got lost somewhere along the way. Instead, the current glue code aligns the input pointer to 16 bytes, which is not really necessary on this architecture (although it could be beneficial to performance to expose aligned data to the the NEON routine), but this could result in inputs of less than 16 bytes to be passed in. This not only fails the new extended tests that Eric has implemented, it also results in the code reading past the end of the input, which could potentially result in crashes when dealing with less than 16 bytes of input at the end of a page which is followed by an unmapped page. So update the glue code to only invoke the NEON routine if the input is at least 16 bytes. Reported-by:
-
Ard Biesheuvel authored
commit 62fecf29 upstream. The SIMD routine ported from x86 used to have a special code path for inputs < 16 bytes, which got lost somewhere along the way. Instead, the current glue code aligns the input pointer to permit the NEON routine to use special versions of the vld1 instructions that assume 16 byte alignment, but this could result in inputs of less than 16 bytes to be passed in. This not only fails the new extended tests that Eric has implemented, it also results in the code reading past the end of the input, which could potentially result in crashes when dealing with less than 16 bytes of input at the end of a page which is followed by an unmapped page. So update the glue code to only invoke the NEON routine if the input is at least 16 bytes. Reported-by:
-
Al Viro authored
commit 399504e2 upstream. same story as with last May fixes in sysfs (7b745a4e "unfuck sysfs_mount()"); new_sb is left uninitialized in case of early errors in kernfs_mount_ns() and papering over it by treating any error from kernfs_mount_ns() as equivalent to !new_ns ends up conflating the cases when objects had never been transferred to a superblock with ones when that has happened and resulting new superblock had been dropped. Easily fixed (same way as in sysfs case). Additionally, there's a superblock leak on kernfs_node_dentry() failure *and* a dentry leak inside kernfs_node_dentry() itself - the latter on probably impossible errors, but the former not impossible to trigger (as the matter of fact, injecting allocation failures at that point *does* trigger it). Cc: stable@kernel.org Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Oliver O'Halloran authored
commit 07464e88 upstream. Libnvdimm reserves the first 8K of pfn and devicedax namespaces to store a superblock describing the namespace. This 8K reservation is contained within the altmap area which the kernel uses for the vmemmap backing for the pages within the namespace. The altmap allows for some pages at the start of the altmap area to be reserved and that mechanism is used to protect the superblock from being re-used as vmemmap backing. The number of PFNs to reserve is calculated using: PHYS_PFN(SZ_8K) Which is implemented as: #define PHYS_PFN(x) ((unsigned long)((x) >> PAGE_SHIFT)) So on systems where PAGE_SIZE is greater than 8K the reservation size is truncated to zero and the superblock area is re-used as vmemmap backing. As a result all the namespace information stored in the superblock (i.e. if it's a PFN or DAX namespace) is lost and the namespace needs to be re-created to get access to the contents. This patch fixes this by using PFN_UP() rather than PHYS_PFN() to ensure that at least one page is reserved. On systems with a 4K pages size this patch should have no effect. Cc: stable@vger.kernel.org Cc: Dan Williams <dan.j.williams@intel.com> Fixes: ac515c08 ("libnvdimm, pmem, pfn: move pfn setup to the core") Signed-off-by:
Oliver O'Halloran <oohall@gmail.com> Reviewed-by:
Vishal Verma <vishal.l.verma@intel.com> Signed-off-by:
Dan Williams <dan.j.williams@intel.com> Signed-off-by:
-
Dan Williams authored
commit fa7d2e63 upstream. For recovery, where non-dax access is needed to a given physical address range, and testing, allow the 'force_raw' attribute to override the default establishment of a dev_pagemap. Otherwise without this capability it is possible to end up with a namespace that can not be activated due to corrupted info-block, and one that can not be repaired due to a section collision. Cc: <stable@vger.kernel.org> Fixes: 004f1afb ("libnvdimm, pmem: direct map legacy pmem by default") Signed-off-by:
-
Wei Yang authored
commit f101ada7 upstream. When trying to see whether current nd_region intersects with others, trim_pfn_device() has already calculated the *size* to be expanded to SECTION size. Do not double append 'adjust' to 'size' when calculating whether the end of a region collides with the next pmem region. Fixes: ae86cbfe "libnvdimm, pfn: Pad pfn namespaces relative to other regions" Cc: <stable@vger.kernel.org> Signed-off-by:
Wei Yang <richardw.yang@linux.intel.com> Signed-off-by:
-
Dan Williams authored
commit 966d23a0 upstream. The UEFI 2.7 specification sets expectations that the 'updating' flag is eventually cleared. To date, the libnvdimm core has never adhered to that protocol. The policy of the core matches the policy of other multi-device info-block formats like MD-Software-RAID that expect administrator intervention on inconsistent info-blocks, not automatic invalidation. However, some pre-boot environments may unfortunately attempt to "clean up" the labels and invalidate a set when it fails to find at least one "non-updating" label in the set. Clear the updating flag after set updates to minimize the window of vulnerability to aggressive pre-boot environments. Ideally implementations would not write to the label area outside of creating namespaces. Note that this only minimizes the window, it does not close it as the system can still crash while clearing the flag and the set can be subsequently deleted / invalidated by the pre-boot environment. Fixes: f524bf27 ("libnvdimm: write pmem label set") Cc: <stable@vger.kernel.org> Cc: Kelly Couch <kelly.j.couch@intel.com> Signed-off-by:
-
Alexander Shishkin authored
commit bf7cbaae upstream. Using STP_POLICY_ID_SET ioctl command with dummy_stm device, or any STM device that supplies zero mmio channel size, will trigger a division by zero bug in the kernel. Prevent this by disallowing channel widths other than 1 for such devices. Signed-off-by:
Alexander Shishkin <alexander.shishkin@linux.intel.com> Fixes: 7bd1d409 ("stm class: Introduce an abstraction for System Trace Module devices") CC: stable@vger.kernel.org # v4.4+ Signed-off-by:
-
Hans Verkuil authored
commit 5e99456c upstream. Userspace shouldn't set bytesused to 0 for output buffers. vb2_warn_zero_bytesused() warns about this (only once!), but it also calls WARN_ON(1), which is confusing since it is not immediately clear that it warns about a 0 value for bytesused. Just drop the WARN_ON as it serves no purpose. Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Acked-by:
Ezequiel Garcia <ezequiel@collabora.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Cc: Matthias Maennich <maennich@google.com> Signed-off-by:
-
Darrick J. Wong authored
[ Upstream commit 29b00e60 ] When we made the shmem_reserve_inode call in shmem_link conditional, we forgot to update the declaration for ret so that it always has a known value. Dan Carpenter pointed out this deficiency in the original patch. Fixes: 1062af92 ("tmpfs: fix link accounting when a tmpfile is linked in") Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by:
Hugh Dickins <hughd@google.com> Cc: Matej Kupljen <matej.kupljen@gmail.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Mao Wenan authored
[ Upstream commit 4593403f ] cards_found is a static variable, but when it enters atl2_probe(), cards_found is set to zero, the value is not consistent with last probe, so next behavior is not our expect. Signed-off-by:
Mao Wenan <maowenan@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Jiong Wang authored
[ Upstream commit f036ebd9 ] NFP BPF JIT compiler is doing a couple of small optimizations when jitting ALU imm instructions, some of these optimizations could save code-gen, for example: A & -1 = A A | 0 = A A ^ 0 = A However, for ALU32, high 32-bit of the 64-bit register should still be cleared according to ISA semantics. Fixes: cd7df56e ("nfp: add BPF to NFP code translator") Reviewed-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by:
Jiong Wang <jiong.wang@netronome.com> Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
-
Jiong Wang authored
[ Upstream commit 71c19024 ] The intended optimization should be A ^ 0 = A, not A ^ -1 = A. Fixes: cd7df56e ("nfp: add BPF to NFP code translator") Reviewed-by:
-
Vadim Lomovtsev authored
[ Upstream commit 0dd563b9 ] At the end of NIC VF initialization VF sends CFG_DONE message to PF without using nicvf_msg_send_to_pf routine. This potentially could re-write data in mailbox. This commit is to implement common way of sending CFG_DONE message by the same way with other configuration messages by using nicvf_send_msg_to_pf() routine. Signed-off-by:
Vadim Lomovtsev <vlomovtsev@marvell.com> Signed-off-by:
-
Li RongQing authored
[ Upstream commit 17407715 ] genlmsg_reply can fail, so propagate its return code Signed-off-by:
Li RongQing <lirongqing@baidu.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Arnd Bergmann authored
[ Upstream commit 6321aa19 ] clang warns about overflowing the data[] member in the struct pnpipehdr: net/phonet/pep.c:295:8: warning: array index 4 is past the end of the array (which contains 1 element) [-Warray-bounds] if (hdr->data[4] == PEP_IND_READY) ^ ~ include/net/phonet/pep.h:66:3: note: array 'data' declared here u8 data[1]; Using a flexible array member at the end of the struct avoids the warning, but since we cannot have a flexible array member inside of the union, each index now has to be moved back by one, which makes it a little uglier. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Acked-by:
Rémi Denis-Courmont <remi@remlab.net> Signed-off-by:
-
Vineet Gupta authored
[ Upstream commit e494239a ] There's a hardware bug which affects the HSDK platform, triggered by micro-ops for auto-saving regfile on taken interrupt. The workaround is to inhibit autosave. Signed-off-by:
Vineet Gupta <vgupta@synopsys.com> Signed-off-by:
-
Vineet Gupta authored
[ Upstream commit d5e3c55e ] Newer ARC gcc handles lp_start, lp_end in a different way and doesn't like them in the clobber list. Signed-off-by:
-
Eugeniy Paltsev authored
[ Upstream commit f8a15f97 ] ARCv2 optimized memcpy uses PREFETCHW instruction for prefetching the next cache line but doesn't ensure that the line is not past the end of the buffer. PRETECHW changes the line ownership and marks it dirty, which can cause data corruption if this area is used for DMA IO. Fix the issue by avoiding the PREFETCHW. This leads to performance degradation but it is OK as we'll introduce new memcpy implementation optimized for unaligned memory access using. We also cut off all PREFETCH instructions at they are quite useless here: * we call PREFETCH right before LOAD instruction call. * we copy 16 or 32 bytes of data (depending on CONFIG_ARC_HAS_LL64) in a main logical loop. so we call PREFETCH 4 times (or 2 times) for each L1 cache line (in case of 64B L1 cache Line which is default case). Obviously this is not optimal. Signed-off-by:
Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by:
-
Jeff Kirsher authored
[ Upstream commit 156a67a9 ] The enabling L3/L4 filtering for transmit switched packets for all devices caused unforeseen issue on older devices when trying to send UDP traffic in an ordered sequence. This bit was originally intended for X550 devices, which supported this feature, so limit the scope of this bit to only X550 devices. Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Tested-by:
Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by:
-
Darrick J. Wong authored
[ Upstream commit 1062af92 ] tmpfs has a peculiarity of accounting hard links as if they were separate inodes: so that when the number of inodes is limited, as it is by default, a user cannot soak up an unlimited amount of unreclaimable dcache memory just by repeatedly linking a file. But when v3.11 added O_TMPFILE, and the ability to use linkat() on the fd, we missed accommodating this new case in tmpfs: "df -i" shows that an extra "inode" remains accounted after the file is unlinked and the fd closed and the actual inode evicted. If a user repeatedly links tmpfiles into a tmpfs, the limit will be hit (ENOSPC) even after they are deleted. Just skip the extra reservation from shmem_link() in this case: there's a sense in which this first link of a tmpfile is then cheaper than a hard link of another file, but the accounting works out, and there's still good limiting, so no need to do anything more complicated. Link: http://lkml.kernel.org/r/alpine.LSU.2.11.1902182134370.7035@eggly.anvils Fixes: f4e0c30c ("allow the temp files created by open() to be linked to") Signed-off-by:
Matej Kupljen <matej.kupljen@gmail.com> Acked-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Russell King authored
[ Upstream commit a8fef9ba ] Booting 4.20 on SolidRun Clearfog issues this warning with DMA API debug enabled: WARNING: CPU: 0 PID: 555 at kernel/dma/debug.c:1230 check_sync+0x514/0x5bc mvneta f1070000.ethernet: DMA-API: device driver tries to sync DMA memory it has not allocated [device address=0x000000002dd7dc00] [size=240 bytes] Modules linked in: ahci mv88e6xxx dsa_core xhci_plat_hcd xhci_hcd devlink armada_thermal marvell_cesa des_generic ehci_orion phy_armada38x_comphy mcp3021 spi_orion evbug sfp mdio_i2c ip_tables x_tables CPU: 0 PID: 555 Comm: bridge-network- Not tainted 4.20.0+ #291 Hardware name: Marvell Armada 380/385 (Device Tree) [<c0019638>] (unwind_backtrace) from [<c0014888>] (show_stack+0x10/0x14) [<c0014888>] (show_stack) from [<c07f54e0>] (dump_stack+0x9c/0xd4) [<c07f54e0>] (dump_stack) from [<c00312bc>] (__warn+0xf8/0x124) [<c00312bc>] (__warn) from [<c00313b0>] (warn_slowpath_fmt+0x38/0x48) [<c00313b0>] (warn_slowpath_fmt) from [<c00b0370>] (check_sync+0x514/0x5bc) [<c00b0370>] (check_sync) from [<c00b04f8>] (debug_dma_sync_single_range_for_cpu+0x6c/0x74) [<c00b04f8>] (debug_dma_sync_single_range_for_cpu) from [<c051bd14>] (mvneta_poll+0x298/0xf58) [<c051bd14>] (mvneta_poll) from [<c0656194>] (net_rx_action+0x128/0x424) [<c0656194>] (net_rx_action) from [<c000a230>] (__do_softirq+0xf0/0x540) [<c000a230>] (__do_softirq) from [<c00386e0>] (irq_exit+0x124/0x144) [<c00386e0>] (irq_exit) from [<c009b5e0>] (__handle_domain_irq+0x58/0xb0) [<c009b5e0>] (__handle_domain_irq) from [<c03a63c4>] (gic_handle_irq+0x48/0x98) [<c03a63c4>] (gic_handle_irq) from [<c0009a10>] (__irq_svc+0x70/0x98) ... This appears to be caused by mvneta_rx_hwbm() calling dma_sync_single_range_for_cpu() with the wrong struct device pointer, as the buffer manager device pointer is used to map and unmap the buffer. Fix this. Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by:
-
Vladimir Murzin authored
[ Upstream commit 74698f69 ] Updates to the GIC architecture allow ID_AA64PFR0_EL1.GIC to have values other than 0 or 1. At the moment, Linux is quite strict in the way it handles this field at early boot stage (cpufeature is fine) and will refuse to use the system register CPU interface if it doesn't find the value 1. Fixes: 021f6537 ("irqchip: gic-v3: Initial support for GICv3") Reported-by:
Chase Conklin <Chase.Conklin@arm.com> Reviewed-by:
Marc Zyngier <marc.zyngier@arm.com> Signed-off-by:
Vladimir Murzin <vladimir.murzin@arm.com> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
-
