The valid compatible string for the tps65132 regulator
is "ti,tps65132".

Change it.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The SAI2_TXC pin is left unconnected per the imx8mp-debix-model-a
schematics:

https://debix.io/Uploads/Temp/file/20230331/DEBIX%20Model%20A%20Schematics.pdf

Also, the RTS5411E USB hub chip does not have a reset pin.

Remove this pin description to properly describe the hardware.

This also fixes the following schema warning:

hub@1: 'reset-gpios' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/usb/realtek,rts5411.yaml#

Fixes: 0253e1cb ("arm64: dts: imx8mp-debix: add USB host support")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Per ethernet-phy.yaml, the expected value for the 'reset-names'
property is "phy".

Change it accordingly to fix the following schema warning:

imx8qm-apalis-ixora-v1.1.dtb: ethernet-phy@7: reset-names:0: 'phy' was expected
from schema $id: http://devicetree.org/schemas/net/ethernet-phy.yaml#Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Per microchip,ksz.yaml, phy-mode is not a valid property in the
top-level switch node.

phy-mode = "rgmii-id" is already passed in the CPU port switch (port@5).

Remove it from the top-level switch node to fix the following
schema warning:

switch@5f: Unevaluated properties are not allowed ('phy-mode' was unexpected)
from schema $id: http://devicetree.org/schemas/net/dsa/microchip,ksz.yamlSigned-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the TPM device found on the GW73xx revision F PCB.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the TPM device found on the GW73xx revision F PCB.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Per nxp,dwmac-imx.yaml, it is not valid to pass 'phy-supply'.

The reg_module_eth1phy regulator is marked with 'regulator-always-on',
so it is safe to remove it from the eqos node.

Remove it to fix the following schema warning:

imx8mp-verdin-nonwifi-dahlia.dtb: ethernet@30bf0000: Unevaluated properties are not allowed ('phy-supply' was unexpected)
	from schema $id: http://devicetree.org/schemas/net/nxp,dwmac-imx.yaml#Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The first compatible entry for the jpegenc should be 'nxp,imx8qm-jpgenc'.

Change it accordingly to fix the following schema warning:

imx8qm-apalis-eval.dtb: jpegenc@58450000: compatible: 'oneOf' conditional failed, one must be fixed:
	'nxp,imx8qm-jpgdec' is not one of ['nxp,imx8qxp-jpgdec', 'nxp,imx8qxp-jpgenc']
	'nxp,imx8qm-jpgenc' was expected
	'nxp,imx8qxp-jpgdec' was expected

Fixes: 5bb27917 ("arm64: dts: imx8: Add jpeg encoder/decoder nodes")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Mirela Rabulea <mirela.rabulea@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Per fsl-lpuart.yaml, the dmas and dma-names entries should be
'rx' followed by 'tx'.

Change the order to fix the following schema warning:

imx93-11x11-evk.dtb: serial@44380000: dma-names:0: 'rx' was expected
	from schema $id: http://devicetree.org/schemas/serial/fsl-lpuart.yaml#
imx93-11x11-evk.dtb: serial@44380000: dma-names:1: 'tx' was expected
	from schema $id: http://devicetree.org/schemas/serial/fsl-lpuart.yaml#Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Per gateworks-gsc.yaml, #address-cells and #size-cells are mandatory
properties.

Pass them to fix the following schema warning:

imx8mm-venice-gw7903.dtb: gsc@20: '#address-cells' is a required property
	from schema $id: http://devicetree.org/schemas/mfd/gateworks-gsc.yaml#
imx8mm-venice-gw7903.dtb: gsc@20: '#size-cells' is a required property
	from schema $id: http://devicetree.org/schemas/mfd/gateworks-gsc.yaml#Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Pass 'fsl,imx8dxl-sc-wdt' to fix the following schema warning:

system-controller: watchdog:compatible:0: 'fsl,imx8qxp-sc-wdt' was expected
	from schema $id: http://devicetree.org/schemas/firmware/fsl,scu.yaml#
system-controller: watchdog:compatible: ['fsl,imx-sc-wdt'] is too short
	from schema $id: http://devicetree.org/schemas/firmware/fsl,scu.yaml#Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Pass 'fsl,imx8dxl-sc-thermal' to fix the following schema warning:

system-controller: thermal-sensor:compatible:0: 'fsl,imx8qxp-sc-thermal' was expected
	from schema $id: http://devicetree.org/schemas/firmware/fsl,scu.yaml#
system-controller: thermal-sensor:compatible: ['fsl,imx-sc-thermal'] is too short
	from schema $id: http://devicetree.org/schemas/firmware/fsl,scu.yaml#Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

wakeup-irq is not documented, and not used anywhere.

Remove it.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Pass 'fsl,imx8dl-scu-pd' to fix the following schema warning:

system-controller: power-controller:compatible:0: 'fsl,scu-pd' is not one of ['fsl,imx8qm-scu-pd', 'fsl,imx8qxp-scu-pd']
	from schema $id: http://devicetree.org/schemas/firmware/fsl,scu.yaml#Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Enable uart2 and uart3 for imx8qm-mek board.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Enable uart2 and uart3 for imx8qxp-mek board.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Original irq number combined UART irq and DMA irq. These doesn't match
uart driver and dma engine's expection.

Update to the irq numbers, which just uart can trigger.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

imx8qm have difference dma channel number for uart[0..3].
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add dma support uart[0..3].
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

edma<n> is missed, add them.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Wrap the usb controllers in an intermediate simple-bus and use it to
constrain the dma address size of these usb controllers to the 40b
that they generate toward the interconnect. This is required because
the SoC uses 48b address sizes and this mismatch would lead to smmu
context faults [1] because the usb generates 40b addresses while the
smmu page tables are populated with 48b wide addresses.

[1]
xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002000010
xhci-hcd xhci-hcd.0.auto: irq 108, io mem 0x03100000
xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
arm-smmu 5000000.iommu: Unhandled context fault: fsr=0x402, iova=0xffffffb000, fsynr=0x0, cbfrsynra=0xc01, cb=3
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

phyGATE-Tauri uses a phyCORE-i.MX8MM SoM. Add device tree for the board.
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX fixes for 6.6:

- A couple of i.MX8MP device tree changes from Adam Ford to fix clock
  configuration regressions caused by 16c98452 ("arm64: dts: imx8mp:
  don't initialize audio clocks from CCM node").
- Fix pmic-irq-hog GPIO line in imx93-tqma9352 device tree.
- Fix a mmemory leak with error handling path of imx_dsp_setup_channels()
  in imx-dsp driver.
- Fix HDMI node in imx8mm-evk device tree.
- Add missing clock enable functionality for imx8mm_soc_uid() function
  in soc-imx8m driver.
- Add missing imx8mm-prt8mm.dtb build target.

The Thermal Monitoring Unit (TMU) interrupt is number 83.

Describe it in the devicetree to fix the following schema warning:

imx93-11x11-evk.dtb: tmu@44482000: 'oneOf' conditional failed, one must be fixed:
	'interrupts' is a required property
	'interrupts-extended' is a required property
	from schema $id: http://devicetree.org/schemas/thermal/qoriq-thermal.yaml#Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Per i2c-imx-lpi2c.yaml, the imx8dxl lpi2c compatible should be:

compatible = "fsl,imx8dxl-lpi2c", "fsl,imx7ulp-lpi2c";

Change it accordingly to fix the following schema warning:

imx8dxl-evk.dtb: i2c@5a800000: compatible: 'oneOf' conditional failed, one must be fixed:
	['fsl,imx8dxl-lpi2c', 'fsl,imx8qxp-lpi2c', 'fsl,imx7ulp-lpi2c'] is too long
	'fsl,imx8dxl-lpi2c' is not one of ['fsl,imx7ulp-lpi2c']
	'fsl,imx7ulp-lpi2c' was expected
	from schema $id: http://devicetree.org/schemas/i2c/i2c-imx-lpi2c.yaml#Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Per fsl,scu-pinctrl.yaml, the pinctrl node names should end with 'grp'.

Change them to fix the following schema warning:

imx8qxp-colibri-iris-v2.dtb: pinctrl: 'enable_3v3_vmmc', 'lcd-lvds' do not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/pinctrl/fsl,scu-pinctrl.yaml#Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Use the full compatible list for the imx8dl FEC as per fsl,fec.yaml.

This fixes the following schema warning:

imx8dxl-evk.dtb: ethernet@5b040000: compatible: 'oneOf' conditional failed, one must be fixed:
	['fsl,imx8qm-fec'] is too short
	'fsl,imx8qm-fec' is not one of ['fsl,imx25-fec', 'fsl,imx27-fec', 'fsl,imx28-fec', 'fsl,imx6q-fec', 'fsl,mvf600-fec', 'fsl,s32v234-fec']
	'fsl,imx8qm-fec' is not one of ['fsl,imx53-fec', 'fsl,imx6sl-fec']
	'fsl,imx8qm-fec' is not one of ['fsl,imx35-fec', 'fsl,imx51-fec']
	'fsl,imx8qm-fec' is not one of ['fsl,imx6ul-fec', 'fsl,imx6sx-fec']
	'fsl,imx8qm-fec' is not one of ['fsl,imx7d-fec']
	'fsl,imx8mq-fec' was expected
	'fsl,imx8qm-fec' is not one of ['fsl,imx8mm-fec', 'fsl,imx8mn-fec', 'fsl,imx8mp-fec', 'fsl,imx93-fec']
	'fsl,imx8qm-fec' is not one of ['fsl,imx8dxl-fec', 'fsl,imx8qxp-fec']
	'fsl,imx8qm-fec' is not one of ['fsl,imx8ulp-fec']
	from schema $id: http://devicetree.org/schemas/net/fsl,fec.yaml#Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The 'nand-on-flash-bbt' property is a property for the NAND device,
not for the GPMI nand controller.

Remove it to fix the following schema warnings:

imx8mm-ddr4-evk.dtb: nand-controller@33002000: Unevaluated properties are not allowed ('nand-on-flash-bbt' was unexpected)
	from schema $id: http://devicetree.org/schemas/mtd/gpmi-nand.yaml#
imx8mn-bsh-smm-s2.dtb: nand-controller@33002000: Unevaluated properties are not allowed ('nand-on-flash-bbt' was unexpected)
	from schema $id: http://devicetree.org/schemas/mtd/gpmi-nand.yaml#Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The mac-address is passed as a subnode of the eeprom and its 'reg'
property describe a range of addresses in the eeprom.

Therefore, #size-cells should be set to 1 instead of 0.

This fixes the following schema warnings:

imx8mp-debix-som-a-bmb-08.dtb: eeprom@52: #size-cells:0:0: 1 was expected
	from schema $id: http://devicetree.org/schemas/eeprom/at24.yaml#
imx8mp-debix-som-a-bmb-08.dtb: eeprom@52: mac-address@0:reg: [[0], [12]] is too long
	from schema $id: http://devicetree.org/schemas/eeprom/at24.yaml#
imx8mp-debix-som-a-bmb-08.dtb: eeprom@52: mac-address@c:reg: [[12], [12]] is too long
	from schema $id: http://devicetree.org/schemas/eeprom/at24.yaml#
imx8mp-debix-som-a-bmb-08.dtb: eeprom@52: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'mac-address@0', 'mac-address@c' were unexpected)
	from schema $id: http://devicetree.org/schemas/eeprom/at24.yaml#Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The PWM interrupt is mandatory per imx-pwm.yaml.

Add them.

This also fixes the followig schema warning:

imx8qm-apalis-v1.1-ixora-v1.2.dtb: pwm@5d000000: 'oneOf' conditional failed, one must be fixed:
	'interrupts' is a required property
	'interrupts-extended' is a required property
	from schema $id: http://devicetree.org/schemas/pwm/imx-pwm.yaml#Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

imx8mm-prt8mm.dts was not getting built. Add it to the build.

Fixes: 58497d7a ("arm64: dts: imx: add Protonic PRT8MM board")
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Per bq25890.yaml, 'phys', 'ti,use-vinmin-threshold', 'ti,vinmin-threshold'
are not valid properties.

Remove them to fix the following schema warning:

imx8mq-librem5-r2.dtb: charger@6a: Unevaluated properties are not allowed ('phys', 'ti,use-vinmin-threshold', 'ti,vinmin-threshold' were unexpected)
	from schema $id: http://devicetree.org/schemas/power/supply/bq25890.yaml#Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Per fsl-imx-gpio.yaml, 'pad-wakeup' and 'pad-wakeup-num' are not
valid properties/

Remove them to fix the following schema warning:

imx8qm-apalis-ixora-v1.1.dtb: gpio@5d0a0000: 'pad-wakeup', 'pad-wakeup-num' do not match any of the regexes: '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$', 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/gpio/fsl-imx-gpio.yaml#Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Per fsl-imx-gpio.yaml, 'ngpios' is not a valid property.

Remove it to fix the following schema warning:

imx8qm-apalis-v1.1-ixora-v1.2.dtb: gpio@5d0d0000: 'ngpios' does not match any of the regexes: '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$', 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/gpio/fsl-imx-gpio.yaml#Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Per mdio-gpio.yaml, the node name should be 'mdio'.

Change it accordingly to fix the following schema warning:

imx8mq-zii-ultra-zest.dtb: bitbang-mdio: $nodename:0: 'bitbang-mdio' does not match '^mdio(@.*)?'
	from schema $id: http://devicetree.org/schemas/net/mdio-gpio.yaml#Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Per i2c-mux-pca954x.yaml, the PCA9546 I2C subnodes should be in the
'i2c@' format.

Change it accordingly to fix the following schema warning:

imx8mm-nitrogen-r2.dtb: i2c-mux@70: Unevaluated properties are not allowed ('i2c3@0' was unexpected)
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

According to st,st-sensors.yaml, the 'interrupt-names' property is
not a valid one.

Remove it to fix the following schema warnings:

imx8mp-venice-gw73xx-2x.dtb: accelerometer@19: 'interrupt-names' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/iio/st,st-sensors.yaml#Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

spi-nxp-fspi.yaml expects the clock-names entries to be in
the following order: "fspi_en", "fspi".

Change it accordingly to fix the following schema warnings:

imx8ulp-evk.dtb: spi@29810000: clock-names:0: 'fspi_en' was expected
	from schema $id: http://devicetree.org/schemas/spi/spi-nxp-fspi.yaml#
imx8ulp-evk.dtb: spi@29810000: clock-names:1: 'fspi' was expected
	from schema $id: http://devicetree.org/schemas/spi/spi-nxp-fspi.yaml#Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

nxp,fspi-dll-slvdly is not documented nor used anywhere.

Drop this invalid property.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The conn_enet0_root_clk node does not have any register associated with it,
so it should be moved outside of soc to fix schema warning from
simple-bus.yaml.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>