Add support for pinctrl on MT7622 SoC. The IO core found on the SoC has
the registers for pinctrl, pinconf and gpio mixed up in the same register
range. However, the IO core for the MT7622 SoC is completely distinct from
anyone of previous MediaTek SoCs which already had support, such as
the hardware internal, register address map and register detailed
definition for each pin.

Therefore, instead, the driver is being newly implemented by reusing
generic methods provided from the core layer with GENERIC_PINCONF,
GENERIC_PINCTRL_GROUPS, and GENERIC_PINMUX_FUNCTIONS for the sake of code
simplicity and rid of superfluous code. Where the function of pins
determined by groups is utilized in this driver which can help developers
less confused with what combinations of pins effective on the SoC and even
reducing the mistakes during the integration of those relevant boards.

As the gpio_chip handling is also only a few lines, the driver also
implements the gpio functionality directly through GPIOLIB.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Since lots of MediaTek drivers had been added, it seems slightly better
for that adding cleanup for placing MediaTek pinctrl drivers under the
independent menu as other kinds of drivers usually was done.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add devicetree bindings for MediaTek MT7622 pinctrl driver.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Biao Huang <biao.huang@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This driver consists of 2 controllers due to a hole in mapping:
-1 controller for GPIO bankA to K.
-1 controller for GPIO bankZ.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds a list of supported STM32 SoC bindings.
Signed-off-by: Gwenael Treuveur <gwenael.treuveur@st.com>
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

In case a platform only defaults a "default" set of pins, but not a
"sleep" set of pins, and this particular platform suspends and resumes
in a way that the pin states are not preserved by the hardware, when we
resume, we would call pinctrl_single_resume() -> pinctrl_force_default()
-> pinctrl_select_state() and the first thing we do is check that the
pins state is the same as before, and do nothing.

In order to fix this, decouple the actual state change from
pinctrl_select_state() and move it pinctrl_commit_state(), while keeping
the p->state == state check in pinctrl_select_state() not to change the
caller assumptions. pinctrl_force_sleep() and pinctrl_force_default()
are updated to bypass the state check by calling pinctrl_commit_state().

[Linus Walleij]
The forced pin control states are currently only used in some pin
controller drivers that grab their own reference to their own pins.
This is equal to the pin control hogs: pins taken by pin control
devices since there are no corresponding device in the Linux device
hierarchy, such as memory controller lines or unused GPIO lines,
or GPIO lines that are used orthogonally from the GPIO subsystem
but pincontrol-wise managed as hogs (non-strict mode, allowing
simultaneous use by GPIO and pin control). For this case forcing
the state from the drivers' suspend()/resume() callbacks makes
sense and should semantically match the name of the function.

Fixes: 6e5e959d ("pinctrl: API changes to support multiple states per device")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add missing copyright and add SPDX identifier.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add the documentation for the Microsemi Ocelot pinmuxing and gpio
controller.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

According to datasheet, we should use numbers for the pin naming
instead of letters. The patch here try to fix this to keep
the consistency.

This patch should not bring any functional change.

Fixes: 83c56680 ("pinctrl: meson-axg: Add new pinctrl driver for Meson AXG SoC")
Suggested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The AXP813 has only two GPIOs. GPIO0 can either be used as a GPIO, an
LDO regulator or an ADC. GPIO1 can be used either as a GPIO or an LDO
regulator.

Moreover, the status bit of the GPIOs when in input mode is not offset
by 4 unlike the AXP209.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

To prepare for patches that will add support for a new PMIC that has a
different GPIO adc muxing value, add an adc_mux within axp20x_pctl
structure and use it.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

To prepare for patches that will add support for a new PMIC that has a
different GPIO input status register, add a gpio_status_offset within
axp20x_pctl structure and use it.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This driver used to do only GPIO features of the GPIOs in X-Powers
AXP20X. Now that we have migrated everything to the pinctrl subsystem
and added pinctrl features, rename everything related to pinctrl from
gpio to pctl to ease the understanding of differences between GPIO
and pinctrl features.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The X-Powers AXP209 has 3 GPIOs. GPIO0/1 can each act either as a GPIO,
an ADC or a LDO regulator. GPIO2 can only act as a GPIO.

This adds the pinctrl features to the driver so GPIO0/1 can be used as
ADC or LDO regulator.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The X-Powers AXP209 has 3 GPIOs. GPIO0/1 can each act either as a GPIO,
an ADC or a LDO regulator. GPIO2 can only act as a GPIO.

This adds the pinctrl features to the driver so GPIO0/1 can be used as
ADC or LDO regulator.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

To prepare the driver for the upcoming pinctrl features, move the GPIO
driver AXP209 from GPIO to pinctrl subsystem.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Checkpatch complains with the following message:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'

Let's make it happy by switching over to unsigned int.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

In the (unlikely) event that community->ngpps is zero, or if every
gpp->gpio_base is less than zero, then an ininitialized value in
ret is returned by function intel_gpio_add_pin_ranges. Fix this by
ensuring ret is initialized to zero.  It's a moot point, but I think
it is worthwhile ensuring this corner case is fixed.

Detected by CoverityScan, CID#1462415 ("Uninitialized scalar variable")

Fixes: a60eac32 ("pinctrl: intel: Allow custom GPIO base for pad groups")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Gemini pin controller can set drive strength for a few
select groups of pins (not individually). Implement this
for GMAC0 and 1 (ethernet ports), IDE and PCI.

Cc: devicetree@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The driver has been in the tree for a while, but its binding document
is missing.  Hence, here it is.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Uniformize STMicroelectronics copyrights header
Add SPDX identifier
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

When a GPIO is requested using gpiod_get_* APIs the intel pinctrl driver
switches the pin to GPIO mode and makes sure interrupts are routed to
the GPIO hardware instead of IOAPIC. However, if the GPIO is used
directly through irqchip, as is the case with many I2C-HID devices where
I2C core automatically configures interrupt for the device, the pin is
not initialized as GPIO. Instead we rely that the BIOS configures the
pin accordingly which seems not to be the case at least in Asus X540NA
SKU3 with Focaltech touchpad.

When the pin is not properly configured it might result weird behaviour
like interrupts suddenly stop firing completely and the touchpad stops
responding to user input.

Fix this by properly initializing the pin to GPIO mode also when it is
used directly through irqchip.

Fixes: 7981c001 ("pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support")
Reported-by: Daniel Drake <drake@endlessm.com>
Reported-and-tested-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The comment block of this file indicates GPL-2.0 "only", while the
MODULE_LICENSE is GPL-2.0 "or later", as include/linux/module.h
describes as follows:

  "GPL"                           [GNU Public License v2 or later]
  "GPL v2"                        [GNU Public License v2]

I am the author of this driver, and my intention is GPL-2.0 "only".

Fixes: dbe776c2 ("gpio: uniphier: add UniPhier GPIO controller driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This change resolves a new compile-time warning
when built as a loadable module:

WARNING: modpost: missing MODULE_LICENSE() in drivers/pinctrl/pxa/pinctrl-pxa2xx.o
see include/linux/module.h for more information

This adds the license as "GPL v2", which matches the header of the file.

MODULE_DESCRIPTION and MODULE_AUTHOR are also added.
Signed-off-by: Jesse Chan <jc@linux.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The 3512 has two more GPIO groups on GPIO area 0, so let's
make it possible to combine these with the function.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add new pinctrl driver for Amlogic's Meson-AXG SoC.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The pin controller has been updated in the Amlogic Meson AXG series,
which use continuous 4-bit register to select function for each pin.
In order to support this, a new pinmux operations "meson_axg_pmx_ops"
has been added.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add compatibles for Amlogic Meson AXG pin controllers
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

* Add a jump target so that a call of the function "mutex_unlock" is stored
  only twice in this function implementation.

* Replace five calls by goto statements.

* Adjust five condition checks.

This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Cannon Lake Windows GPIO driver always exposes 32 pins per "bank"
regardless of whether the hardware actually has that many pins in a pad
group. This means that there are gaps in the GPIO number space even if
such gaps do not exist in the real hardware. To make things worse the
BIOS is also using the same scheme, so for example on Cannon Lake-LP
vGPIO 39 (vSD3_CD_B) the ACPI GpioInt resource has number 231 instead of
the expected 180 (which would be the hardware number).

To make SD card detection and other GPIOs working properly in Linux we
align the pinctrl-cannonlake GPIO numbering to follow the Windows GPIO
driver numbering taking advantage of the gpio_base field introduced in
the previous patch.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Currently we always have direct mapping between GPIO numbers and the
hardware pin numbers. However, there are cases where that's not the case
anymore (more about this in the next patch). Instead we need to be able
to specify custom GPIO base for certain pad groups.

To support this, add a new field (gpio_base) to the pad group structure
and update the core Intel pinctrl driver to handle this accordingly.
Passing 0 as gpio_base will use direct mapping so the existing drivers
do not need to be modified. Passing -1 excludes the whole pad group from
having GPIO mapping.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

We added acpi_gpiochip_pin_to_gpio_offset() because there was a need to
translate from ACPI GpioIo/GpioInt number to Linux GPIO number in the
Cherryview pinctrl driver. This translation is necessary because
Cherryview has gaps in the pin list and the driver used continuous GPIO
number space in Linux side as follows:

  created GPIO range 0->7 ==> INT33FF:03 PIN 0->7
  created GPIO range 8->19 ==> INT33FF:03 PIN 15->26
  created GPIO range 20->25 ==> INT33FF:03 PIN 30->35
  created GPIO range 26->33 ==> INT33FF:03 PIN 45->52
  created GPIO range 34->43 ==> INT33FF:03 PIN 60->69
  created GPIO range 44->54 ==> INT33FF:03 PIN 75->85

For example when ACPI GpioInt resource refers to GPIO 81 (SDMMC3_CD_B)
we translate from pin 81 to the corresponding Linux GPIO number, which
is 50. This number is then used when the GPIO is accessed through gpiolib.

It turns out, this is not necessary at all. We can just pass 1:1 mapping
between Linux GPIO numbers and pin numbers (including gaps) and the
pinctrl core handles all the details automatically:

  created GPIO range 0->7 ==> INT33FF:03 PIN 0->7
  created GPIO range 15->26 ==> INT33FF:03 PIN 15->26
  created GPIO range 30->35 ==> INT33FF:03 PIN 30->35
  created GPIO range 45->52 ==> INT33FF:03 PIN 45->52
  created GPIO range 60->69 ==> INT33FF:03 PIN 60->69
  created GPIO range 75->85 ==> INT33FF:03 PIN 75->85

Here GPIO 81 is exactly same than the hardware pin 81 (SDMMC3_CD_B).

As an added bonus this simplifies both the ACPI GPIO core code and the
Cherryview pinctrl driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

On Intel Merrifield the pin control device is a separate IP block
without any PCI ID assigned.

Though, recently we got an allocated ACPI ID for it, so, let's use fresh
ID.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Pull ARM fixes from Russell King:

 - LPAE fixes for kernel-readonly regions

 - Fix for get_user_pages_fast on LPAE systems

 - avoid tying decompressor to a particular platform if DEBUG_LL is
   enabled

 - BUG if we attempt to return to userspace but the to-be-restored PSR
   value keeps us in privileged mode (defeating an issue that ftracetest
   found)

* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: BUG if jumping to usermode address in kernel mode
  ARM: 8722/1: mm: make STRICT_KERNEL_RWX effective for LPAE
  ARM: 8721/1: mm: dump: check hardware RO bit for LPAE
  ARM: make decompressor debug output user selectable
  ARM: fix get_user_pages_fast

Pull irq fixes from Thomas Glexiner:

 - unbreak the irq trigger type check for legacy platforms

 - a handful fixes for ARM GIC v3/4 interrupt controllers

 - a few trivial fixes all over the place

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq/matrix: Make - vs ?: Precedence explicit
  irqchip/imgpdc: Use resource_size function on resource object
  irqchip/qcom: Fix u32 comparison with value less than zero
  irqchip/exiu: Fix return value check in exiu_init()
  irqchip/gic-v3-its: Remove artificial dependency on PCI
  irqchip/gic-v4: Add forward definition of struct irq_domain_ops
  irqchip/gic-v3: pr_err() strings should end with newlines
  irqchip/s3c24xx: pr_err() strings should end with newlines
  irqchip/gic-v3: Fix ppi-partitions lookup
  irqchip/gic-v4: Clear IRQ_DISABLE_UNLAZY again if mapping fails
  genirq: Track whether the trigger type has been set

Pull misc x86 fixes from Ingo Molnar:
 - topology enumeration fixes
 - KASAN fix
 - two entry fixes (not yet the big series related to KASLR)
 - remove obsolete code
 - instruction decoder fix
 - better /dev/mem sanity checks, hopefully working better this time
 - pkeys fixes
 - two ACPI fixes
 - 5-level paging related fixes
 - UMIP fixes that should make application visible faults more debuggable
 - boot fix for weird virtualization environment

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
  x86/decoder: Add new TEST instruction pattern
  x86/PCI: Remove unused HyperTransport interrupt support
  x86/umip: Fix insn_get_code_seg_params()'s return value
  x86/boot/KASLR: Remove unused variable
  x86/entry/64: Add missing irqflags tracing to native_load_gs_index()
  x86/mm/kasan: Don't use vmemmap_populate() to initialize shadow
  x86/entry/64: Fix entry_SYSCALL_64_after_hwframe() IRQ tracing
  x86/pkeys/selftests: Fix protection keys write() warning
  x86/pkeys/selftests: Rename 'si_pkey' to 'siginfo_pkey'
  x86/mpx/selftests: Fix up weird arrays
  x86/pkeys: Update documentation about availability
  x86/umip: Print a warning into the syslog if UMIP-protected instructions are used
  x86/smpboot: Fix __max_logical_packages estimate
  x86/topology: Avoid wasting 128k for package id array
  perf/x86/intel/uncore: Cache logical pkg id in uncore driver
  x86/acpi: Reduce code duplication in mp_override_legacy_irq()
  x86/acpi: Handle SCI interrupts above legacy space gracefully
  x86/boot: Fix boot failure when SMP MP-table is based at 0
  x86/mm: Limit mmap() of /dev/mem to valid physical addresses
  x86/selftests: Add test for mapping placement for 5-level paging
  ...

Pull scheduler fixes from Ingo Molnar:
 "Misc fixes: a documentation fix, a Sparse warning fix and a debugging
  fix"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/debug: Fix task state recording/printout
  sched/deadline: Don't use dubious signed bitfields
  sched/deadline: Fix the description of runtime accounting in the documentation

Pull perf fixes from Ingo Molnar:
 "Misc fixes: two PMU driver fixes and a memory leak fix"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/core: Fix memory leak triggered by perf --namespace
  perf/x86/intel/uncore: Add event constraint for BDX PCU
  perf/x86/intel: Hide TSX events when RTM is not supported