- 27 Oct, 2022 6 commits
-
-
Biju Das authored
RZ/G2L has separate channel specific IRQs for transmit and error interrupts. But the IRQ handler processes both channels, even if there no interrupt occurred on one of the channels. This patch fixes the issue by passing a channel specific context parameter instead of global one for the IRQ register and the IRQ handler, it just handles the channel which is triggered the interrupt. Fixes: 76e9353a ("can: rcar_canfd: Add support for RZ/G2L family") Signed-off-by:
Biju Das <biju.das.jz@bp.renesas.com> Link: https://lore.kernel.org/all/20221025155657.1426948-3-biju.das.jz@bp.renesas.com Cc: stable@vger.kernel.org [mkl: adjust commit message] Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de>
-
Biju Das authored
We are seeing an IRQ storm on the global receive IRQ line under heavy CAN bus load conditions with both CAN channels enabled. Conditions: The global receive IRQ line is shared between can0 and can1, either of the channels can trigger interrupt while the other channel's IRQ line is disabled (RFIE). When global a receive IRQ interrupt occurs, we mask the interrupt in the IRQ handler. Clearing and unmasking of the interrupt is happening in rx_poll(). There is a race condition where rx_poll() unmasks the interrupt, but the next IRQ handler does not mask the IRQ due to NAPIF_STATE_MISSED flag (e.g.: can0 RX FIFO interrupt is disabled and can1 is triggering RX interrupt, the delay in rx_poll() processing results in setting NAPIF_STATE_MISSED flag) leading to an IRQ storm. This patch fixes the issue by checking IRQ active and enabled before handling the IRQ on a particular channel. Fixes: dd3bd23e ("can: rcar_canfd: Add Renesas R-Car CAN FD driver") Suggested-by:
-
Anssi Hannula authored
kvaser_usb uses completions to signal when a response event is received for outgoing commands. However, it uses init_completion() to reinitialize the start_comp and stop_comp completions before sending the start/stop commands. In case the device sends the corresponding response just before the actual command is sent, complete() may be called concurrently with init_completion() which is not safe. This might be triggerable even with a properly functioning device by stopping the interface (CMD_STOP_CHIP) just after it goes bus-off (which also causes the driver to send CMD_STOP_CHIP when restart-ms is off), but that was not tested. Fix the issue by using reinit_completion() instead. Fixes: 080f40a6 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices") Tested-by:
Jimmy Assarsson <extja@kvaser.com> Signed-off-by:
Anssi Hannula <anssi.hannula@bitwise.fi> Signed-off-by:
-
Kunihiko Hayashi authored
The phylib callback is called after MAC driver's own resume callback is called. For AVE driver, after resuming immediately, PHY state machine is in PHY_NOLINK because there is a time lag from link-down to link-up due to autoneg. The result is WARN_ON() dump in mdio_bus_phy_resume(). Since ave_resume() itself calls phy_resume(), AVE driver should manage PHY PM. To indicate that MAC driver manages PHY PM, set phydev->mac_managed_pm to true to avoid the unnecessary phylib call and add missing phy_init_hw() to ave_resume(). Suggested-by:
Heiner Kallweit <hkallweit1@gmail.com> Fixes: fba863b8 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM") Signed-off-by:
Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Link: https://lore.kernel.org/r/20221024072227.24769-1-hayashi.kunihiko@socionext.comSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Juergen Borleis authored
Using 'ethtool -d […]' on an i.MX6UL leads to a kernel crash: Unhandled fault: external abort on non-linefetch (0x1008) at […] due to this SoC has less registers in its FEC implementation compared to other i.MX6 variants. Thus, a run-time decision is required to avoid access to non-existing registers. Fixes: a51d3ab5 ("net: fec: use a more proper compatible string for i.MX6UL type device") Signed-off-by:
Juergen Borleis <jbe@pengutronix.de> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20221024080552.21004-1-jbe@pengutronix.deSigned-off-by:
-
Jakub Kicinski authored
Merge tag 'linux-can-fixes-for-6.1-20221025' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can Marc Kleine-Budde says: ==================== pull-request: can 2022-10-25 The 1st patch adds a missing cleanup call in the error path of the probe function in mpc5xxx glue code for the mscan driver. The 2nd patch adds a missing cleanup call in the error path of the probe function of the mcp251x driver. * tag 'linux-can-fixes-for-6.1-20221025' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can: can: mcp251x: mcp251x_can_probe(): add missing unregister_candev() in error path can: mscan: mpc5xxx: mpc5xxx_can_probe(): add missing put_clock() in error path ==================== Link: https://lore.kernel.org/r/20221026075520.1502520-1-mkl@pengutronix.deSigned-off-by:
-
- 26 Oct, 2022 5 commits
-
-
Rolf Eike Beer authored
The "random rhlist add/delete operations" actually wasn't very random, as all cases tested the same bit. Since the later parts of this loop depend on the first case execute this unconditionally, and then test on different bits for the remaining tests. While at it only request as much random bits as are actually used. Signed-off-by:
Rolf Eike Beer <eike-kernel@sf-tec.de> Acked-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Caleb Connolly authored
IPA v3.1 doesn't support the IDLE_INDICATION_CFG register, this was causing a harmless splat in ipa_idle_indication_cfg(), add a version check to prevent trying to fetch this register on v3.1 Fixes: 6a244b75 ("net: ipa: introduce ipa_reg()") Signed-off-by:
Caleb Connolly <caleb.connolly@linaro.org> Reviewed-by:
Alex Elder <elder@linaro.org> Tested-by:
Jami Kettunen <jami.kettunen@somainline.org> Link: https://lore.kernel.org/r/20221024234850.4049778-1-caleb.connolly@linaro.orgSigned-off-by:
-
Caleb Connolly authored
The resource group limits for IPA v3.1 mistakenly used 6 bit wide mask values, when the hardware actually uses 8. Out of range values were silently ignored before, so the IPA worked as expected. However the new generalised register definitions introduce stricter checking here, they now cause some splats and result in the value 0 being written instead. Fix the limit bitmask widths so that the correct values can be written. Fixes: 1c418c4a ("net: ipa: define resource group/type IPA register fields") Signed-off-by:
-
Caleb Connolly authored
Some resource limits on IPA v3.5.1 have their max values set to 255, this causes a few splats in ipa_reg_encode and prevents the IPA from booting properly. The limits are all 6 bits wide so adjust the max values to 63. Fixes: 1c418c4a ("net: ipa: define resource group/type IPA register fields") Signed-off-by:
-
Yang Yingliang authored
pci_disable_device() need be called while module exiting, switch to use pcim_enable(), pci_disable_device() will be called in pcim_release() while unbinding device. Fixes: 8ca86fd8 ("net: Micrel KSZ8841/2 PCI Ethernet driver") Signed-off-by:
Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20221024131338.2848959-1-yangyingliang@huawei.comSigned-off-by:
-
- 25 Oct, 2022 15 commits
-
-
Slawomir Laba authored
Fix setting bits for specific flow_type for GLQF_HASH_INSET register. In previous version all of the bits were set only in hena register, while in inset only one bit was set. In order for this working correctly on all types of cards these bits needs to be set correctly for both hena and inset registers. Fixes: eb0dd6e4 ("i40e: Allow RSS Hash set with less than four parameters") Signed-off-by:
Slawomir Laba <slawomirx.laba@intel.com> Signed-off-by:
Michal Jaron <michalx.jaron@intel.com> Signed-off-by:
Mateusz Palczewski <mateusz.palczewski@intel.com> Signed-off-by:
Jacob Keller <jacob.e.keller@intel.com> Link: https://lore.kernel.org/r/20221024100526.1874914-3-jacob.e.keller@intel.comSigned-off-by:
-
Sylwester Dziedziuch authored
When a reset was triggered on one VF with i40e_reset_vf global PF state __I40E_VF_DISABLE was set on a PF until the reset finished. If immediately after triggering reset on one VF there is a request to reset on another it will cause a hang on VF side because VF will be notified of incoming reset but the reset will never happen because of this global state, we will get such error message: [ +4.890195] iavf 0000:86:02.1: Never saw reset and VF will hang waiting for the reset to be triggered. Fix this by introducing new VF state I40E_VF_STATE_RESETTING that will be set on a VF if it is currently resetting instead of the global __I40E_VF_DISABLE PF state. Fixes: 3ba9bcb4 ("i40e: add locking around VF reset") Signed-off-by:
Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com> Signed-off-by:
Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by:
-
Slawomir Laba authored
When enabling flow type for RSS hash via ethtool: ethtool -N $pf rx-flow-hash tcp4|tcp6|udp4|udp6 s|d the driver would fail to setup this setting on X722 device since it was using the mask on the register dedicated for X710 devices. Apply a different mask on the register when setting the RSS hash for the X722 device. When displaying the flow types enabled via ethtool: ethtool -n $pf rx-flow-hash tcp4|tcp6|udp4|udp6 the driver would print wrong values for X722 device. Fix this issue by testing masks for X722 device in i40e_get_rss_hash_opts function. Fixes: eb0dd6e4 ("i40e: Allow RSS Hash set with less than four parameters") Signed-off-by:
-
Eric Dumazet authored
Another syzbot report [1] with no reproducer hints at a bug in ip6_gre tunnel (dev:ip6gretap0) Since ipv6 mcast code makes sure to read dev->mtu once and applies a sanity check on it (see commit b9b312a7 "ipv6: mcast: better catch silly mtu values"), a remaining possibility is that a layer is able to set dev->mtu to an underflowed value (high order bit set). This could happen indeed in ip6gre_tnl_link_config_route(), ip6_tnl_link_config() and ipip6_tunnel_bind_dev() Make sure to sanitize mtu value in a local variable before it is written once on dev->mtu, as lockless readers could catch wrong temporary value. [1] skbuff: skb_over_panic: text:ffff80000b7a2f38 len:40 put:40 head:ffff000149dcf200 data:ffff000149dcf2b0 tail:0xd8 end:0xc0 dev:ip6gretap0 ------------[ cut here ]------------ kernel BUG at net/core/skbuff.c:120 Internal error: Oops - BUG: 00000000f2000800 [#1] PREEMPT SMP Modules linked in: CPU: 1 PID: 10241 Comm: kworker/1:1 Not tainted 6.0.0-rc7-syzkaller-18095-gbbed346d5a96 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/30/2022 Workqueue: mld mld_ifc_work pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : skb_panic+0x4c/0x50 net/core/skbuff.c:116 lr : skb_panic+0x4c/0x50 net/core/skbuff.c:116 sp : ffff800020dd3b60 x29: ffff800020dd3b70 x28: 0000000000000000 x27: ffff00010df2a800 x26: 00000000000000c0 x25: 00000000000000b0 x24: ffff000149dcf200 x23: 00000000000000c0 x22: 00000000000000d8 x21: ffff80000b7a2f38 x20: ffff00014c2f7800 x19: 0000000000000028 x18: 00000000000001a9 x17: 0000000000000000 x16: ffff80000db49158 x15: ffff000113bf1a80 x14: 0000000000000000 x13: 00000000ffffffff x12: ffff000113bf1a80 x11: ff808000081c0d5c x10: 0000000000000000 x9 : 73f125dc5c63ba00 x8 : 73f125dc5c63ba00 x7 : ffff800008161d1c x6 : 0000000000000000 x5 : 0000000000000080 x4 : 0000000000000001 x3 : 0000000000000000 x2 : ffff0001fefddcd0 x1 : 0000000100000000 x0 : 0000000000000089 Call trace: skb_panic+0x4c/0x50 net/core/skbuff.c:116 skb_over_panic net/core/skbuff.c:125 [inline] skb_put+0xd4/0xdc net/core/skbuff.c:2049 ip6_mc_hdr net/ipv6/mcast.c:1714 [inline] mld_newpack+0x14c/0x270 net/ipv6/mcast.c:1765 add_grhead net/ipv6/mcast.c:1851 [inline] add_grec+0xa20/0xae0 net/ipv6/mcast.c:1989 mld_send_cr+0x438/0x5a8 net/ipv6/mcast.c:2115 mld_ifc_work+0x38/0x290 net/ipv6/mcast.c:2653 process_one_work+0x2d8/0x504 kernel/workqueue.c:2289 worker_thread+0x340/0x610 kernel/workqueue.c:2436 kthread+0x12c/0x158 kernel/kthread.c:376 ret_from_fork+0x10/0x20 arch/arm64/kernel/entry.S:860 Code: 91011400 aa0803e1 a90027ea 94373093 (d4210000) Fixes: c12b395a ("gre: Support GRE over IPv6") Reported-by:
syzbot <syzkaller@googlegroups.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20221024020124.3756833-1-eric.dumazet@gmail.comSigned-off-by:
-
Benjamin Gaignard authored
RK3588(s) can have multiple gmac controllers. Re-use rk3568 logic to distinguish them. Fixes: 2f2b60a0 ("net: ethernet: stmmac: dwmac-rk: Add gmac support for rk3588") Signed-off-by:
Benjamin Gaignard <benjamin.gaignard@collabora.com> Signed-off-by:
Sebastian Reichel <sebastian.reichel@collabora.com> Link: https://lore.kernel.org/r/20221021172422.88534-1-sebastian.reichel@collabora.comSigned-off-by:
Paolo Abeni <pabeni@redhat.com>
-
Dongliang Mu authored
In mcp251x_can_probe(), if mcp251x_gpio_setup() fails, it forgets to unregister the CAN device. Fix this by unregistering can device in mcp251x_can_probe(). Fixes: 2d52dabb ("can: mcp251x: add GPIO support") Signed-off-by:
Dongliang Mu <dzm91@hust.edu.cn> Link: https://lore.kernel.org/all/20221024090256.717236-1-dzm91@hust.edu.cn [mkl: adjust label] Signed-off-by:
-
Dongliang Mu authored
The commit 1149108e ("can: mscan: improve clock API use") only adds put_clock() in mpc5xxx_can_remove() function, forgetting to add put_clock() in the error handling code. Fix this bug by adding put_clock() in the error handling code. Fixes: 1149108e ("can: mscan: improve clock API use") Signed-off-by:
-
Jakub Kicinski authored
Merge tag 'ieee802154-for-net-2022-10-24' of git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan Stefan Schmidt says: ==================== pull-request: ieee802154 for net 2022-10-24 Two fixup patches for return code changes of an earlier commit. Wei Yongjun fixed a missed -EINVAL return on the recent change, while Alexander Aring adds handling for unknown address type cases as well. Miquel Raynal fixed a long standing issue with LQI value recording which got broken 8 years ago. (It got more attention with the work in progress enhancement in wpan). * tag 'ieee802154-for-net-2022-10-24' of git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan: mac802154: Fix LQI recording net: ieee802154: fix error return code in dgram_bind() net: ieee802154: return -EINVAL for unknown addr type ==================== Link: https://lore.kernel.org/r/20221024102301.9433-1-stefan@datenfreihafen.orgSigned-off-by:
-
Jakub Kicinski authored
Mat Martineau says: ==================== mptcp: Fixes for 6.1 Patch 1 fixes an issue with assigning subflow IDs in cases where an incoming MP_JOIN is processed before accept() completes on the MPTCP socket. Patches 2 and 3 fix a deadlock issue with fastopen code (new for 6.1) at connection time. ==================== Link: https://lore.kernel.org/r/20221021225856.88119-1-mathew.j.martineau@linux.intel.comSigned-off-by:
-
Paolo Abeni authored
Our CI reported lockdep splat in the fastopen code: ====================================================== WARNING: possible circular locking dependency detected 6.0.0.mptcp_f5e8bfe9878d+ #1558 Not tainted ------------------------------------------------------ packetdrill/1071 is trying to acquire lock: ffff8881bd198140 (sk_lock-AF_INET){+.+.}-{0:0}, at: inet_wait_for_connect+0x19c/0x310 but task is already holding lock: ffff8881b8346540 (k-sk_lock-AF_INET){+.+.}-{0:0}, at: mptcp_sendmsg+0xfdf/0x1740 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 (k-sk_lock-AF_INET){+.+.}-{0:0}: __lock_acquire+0xb6d/0x1860 lock_acquire+0x1d8/0x620 lock_sock_nested+0x37/0xd0 inet_stream_connect+0x3f/0xa0 mptcp_connect+0x411/0x800 __inet_stream_connect+0x3ab/0x800 mptcp_stream_connect+0xac/0x110 __sys_connect+0x101/0x130 __x64_sys_connect+0x6e/0xb0 do_syscall_64+0x59/0x90 entry_SYSCALL_64_after_hwframe+0x63/0xcd -> #0 (sk_lock-AF_INET){+.+.}-{0:0}: check_prev_add+0x15e/0x2110 validate_chain+0xace/0xdf0 __lock_acquire+0xb6d/0x1860 lock_acquire+0x1d8/0x620 lock_sock_nested+0x37/0xd0 inet_wait_for_connect+0x19c/0x310 __inet_stream_connect+0x26c/0x800 tcp_sendmsg_fastopen+0x341/0x650 mptcp_sendmsg+0x109d/0x1740 sock_sendmsg+0xe1/0x120 __sys_sendto+0x1c7/0x2a0 __x64_sys_sendto+0xdc/0x1b0 do_syscall_64+0x59/0x90 entry_SYSCALL_64_after_hwframe+0x63/0xcd other info that might help us debug this: Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(k-sk_lock-AF_INET); lock(sk_lock-AF_INET); lock(k-sk_lock-AF_INET); lock(sk_lock-AF_INET); *** DEADLOCK *** 1 lock held by packetdrill/1071: #0: ffff8881b8346540 (k-sk_lock-AF_INET){+.+.}-{0:0}, at: mptcp_sendmsg+0xfdf/0x1740 ====================================================== The problem is caused by the blocking inet_wait_for_connect() releasing and re-acquiring the msk socket lock while the subflow socket lock is still held and the MPTCP socket requires that the msk socket lock must be acquired before the subflow socket lock. Address the issue always invoking tcp_sendmsg_fastopen() in an unblocking manner, and later eventually complete the blocking __inet_stream_connect() as needed. Fixes: d98a82a6 ("mptcp: handle defer connect in mptcp_sendmsg") Reviewed-by:Mat Martineau <mathew.j.martineau@linux.intel.com> Reviewed-by:
Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by:
-
Paolo Abeni authored
The current MPTCP connect implementation duplicates a bit of inet code and does not use nor provide a struct proto->connect callback, which in turn will not fit the upcoming fastopen implementation. Refactor such implementation to use the common helper, moving the MPTCP-specific bits into mptcp_connect(). Additionally, avoid an indirect call to the subflow connect callback. Note that the fastopen call-path invokes mptcp_connect() while already holding the subflow socket lock. Explicitly keep track of such path via a new MPTCP-level flag and handle the locking accordingly. Additionally, track the connect flags in a new msk field to allow propagating them to the subflow inet_stream_connect call. Fixes: d98a82a6 ("mptcp: handle defer connect in mptcp_sendmsg") Reviewed-by:
-
Paolo Abeni authored
The mptcp_pm_nl_get_local_id() code assumes that the msk local address is available at that point. For passive sockets, we initialize such address at accept() time. Depending on the running configuration and the user-space timing, a passive MPJ subflow can join the msk socket before accept() completes. In such case, the PM assigns a wrong local id to the MPJ subflow and later PM netlink operations will end-up touching the wrong/unexpected subflow. All the above causes sporadic self-tests failures, especially when the host is heavy loaded. Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/308 Fixes: 01cacb00 ("mptcp: add netlink-based PM") Fixes: d045b9eb ("mptcp: introduce implicit endpoints") Reviewed-by:
-
Horatiu Vultur authored
When a frame is sent using FDMA, the skb is mapped and then the mapped address is given to an tx dcb that is different than the last used tx dcb. Once the HW finish with this frame, it would generate an interrupt and then the dcb can be reused and memory can be freed. For each dcb there is an dcb buf that contains some meta-data(is used by PTP, is it free). There is 1 to 1 relationship between dcb and dcb_buf. The following issue was observed. That sometimes after changing the MTU to allocate new tx dcbs and dcbs_buf, two frames were not transmitted. The frames were not transmitted because when reloading the tx dcbs, it was always presuming to use the first dcb but that was not always happening. Because it could be that the last tx dcb used before changing MTU was first dcb and then when it tried to get the next dcb it would take dcb 1 instead of 0. Because it is supposed to take a different dcb than the last used one. This can be fixed simply by changing tx->last_in_use to -1 when the fdma is disabled to reload the new dcb and dcbs_buff. But there could be a different issue. For example, right after the frame is sent, the MTU is changed. Now all the dcbs and dcbs_buf will be cleared. And now get the interrupt from HW that it finished with the frame. So when we try to clear the skb, it is not possible because we lost all the dcbs_buf. The solution here is to stop replacing the tx dcbs and dcbs_buf when changing MTU because the TX doesn't care what is the MTU size, it is only the RX that needs this information. Fixes: 2ea1cbac ("net: lan966x: Update FDMA to change MTU.") Signed-off-by:
Horatiu Vultur <horatiu.vultur@microchip.com> Link: https://lore.kernel.org/r/20221021090711.3749009-1-horatiu.vultur@microchip.comSigned-off-by:
-
Jakub Kicinski authored
To keep backward compatibility we used to leave attribute parsing to the family if no policy is specified. This becomes tedious as we move to more strict validation. Families must define reject all policies if they don't want any attributes accepted. Piggy back on the resv_start_op field as the switchover point. AFAICT only ethtool has added new commands since the resv_start_op was defined, and it has per-op policies so this should be a no-op. Nonetheless the patch should still go into v6.1 for consistency. Link: https://lore.kernel.org/all/20221019125745.3f2e7659@kernel.org/ Link: https://lore.kernel.org/r/20221021193532.1511293-1-kuba@kernel.orgSigned-off-by:
-
Xin Long authored
The similar fix as commit 46cdedf2 ("ethtool: pse-pd: fix null-deref on genl_info in dump") is also needed for ethtool eeprom. Fixes: c781ff12 ("ethtool: Allow network drivers to dump arbitrary EEPROM data") Signed-off-by:
Xin Long <lucien.xin@gmail.com> Link: https://lore.kernel.org/r/5575919a2efc74cd9ad64021880afc3805c54166.1666362167.git.lucien.xin@gmail.comSigned-off-by:
-
- 24 Oct, 2022 14 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds authored
Pull networking fixes from Jakub Kicinski: "Including fixes from bpf. The net-memcg fix stands out, the rest is very run-off-the-mill. Maybe I'm biased. Current release - regressions: - eth: fman: re-expose location of the MAC address to userspace, apparently some udev scripts depended on the exact value Current release - new code bugs: - bpf: - wait for busy refill_work when destroying bpf memory allocator - allow bpf_user_ringbuf_drain() callbacks to return 1 - fix dispatcher patchable function entry to 5 bytes nop Previous releases - regressions: - net-memcg: avoid stalls when under memory pressure - tcp: fix indefinite deferral of RTO with SACK reneging - tipc: fix a null-ptr-deref in tipc_topsrv_accept - eth: macb: specify PHY PM management done by MAC - tcp: fix a signed-integer-overflow bug in tcp_add_backlog() Previous releases - always broken: - eth: amd-xgbe: SFP fixes and compatibility improvements Misc: - docs: netdev: offer performance feedback to contributors" * tag 'net-6.1-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (37 commits) net-memcg: avoid stalls when under memory pressure tcp: fix indefinite deferral of RTO with SACK reneging tcp: fix a signed-integer-overflow bug in tcp_add_backlog() net: lantiq_etop: don't free skb when returning NETDEV_TX_BUSY net: fix UAF issue in nfqnl_nf_hook_drop() when ops_init() failed docs: netdev: offer performance feedback to contributors kcm: annotate data-races around kcm->rx_wait kcm: annotate data-races around kcm->rx_psock net: fman: Use physical address for userspace interfaces net/mlx5e: Cleanup MACsec uninitialization routine atlantic: fix deadlock at aq_nic_stop nfp: only clean `sp_indiff` when application firmware is unloaded amd-xgbe: add the bit rate quirk for Molex cables amd-xgbe: fix the SFP compliance codes check for DAC cables amd-xgbe: enable PLL_CTL for fixed PHY modes only amd-xgbe: use enums for mailbox cmd and sub_cmds amd-xgbe: Yellow carp devices do not need rrc bpf: Use __llist_del_all() whenever possbile during memory draining bpf: Wait for busy refill_work when destroying bpf memory allocator MAINTAINERS: add keyword match on PTP ... -
Linus Torvalds authored
Merge tag 'rcu-urgent.2022.10.20a' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu Pull RCU fix from Paul McKenney: "Fix a regression caused by commit bf95b2bc ("rcu: Switch polled grace-period APIs to ->gp_seq_polled"), which could incorrectly leave interrupts enabled after an early-boot call to synchronize_rcu(). Such synchronize_rcu() calls must acquire leaf rcu_node locks in order to properly interact with polled grace periods, but the code did not take into account the possibility of synchronize_rcu() being invoked from the portion of the boot sequence during which interrupts are disabled. This commit therefore switches the lock acquisition and release from irq to irqsave/irqrestore" * tag 'rcu-urgent.2022.10.20a' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu: rcu: Keep synchronize_rcu() from enabling irqs in early boot
-
Linus Torvalds authored
Merge tag 'linux-kselftest-kunit-fixes-6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest Pull KUnit fixes from Shuah Khan: "One single fix to update alloc_string_stream() callers to check for IS_ERR() instead of NULL to be in sync with alloc_string_stream() returning an ERR_PTR()" * tag 'linux-kselftest-kunit-fixes-6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: kunit: update NULL vs IS_ERR() tests
-
Linus Torvalds authored
Merge tag 'linux-kselftest-fixes-6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest Pull Kselftest fixes from Shuah Khan: - futex, intel_pstate, kexec build fixes - ftrace dynamic_events dependency check fix - memory-hotplug fix to remove redundant warning from test report * tag 'linux-kselftest-fixes-6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: selftests/ftrace: fix dynamic_events dependency check selftests/memory-hotplug: Remove the redundant warning information selftests/kexec: fix build for ARCH=x86_64 selftests/intel_pstate: fix build for ARCH=x86_64 selftests/futex: fix build for clang
-
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrlLinus Torvalds authored
Pull pin control fixes from Linus Walleij: - Fix typos in UART1 and MMC in the Ingenic driver - A really well researched glitch bug fix to the Qualcomm driver that was tracked down and fixed by Dough Anderson from Chromium. Hats off for this one! - Revert two patches on the Xilinx ZynqMP driver: this needs a proper solution making use of firmware version information to adapt to different firmware releases - Fix interrupt triggers in the Ocelot driver * tag 'pinctrl-v6.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: pinctrl: ocelot: Fix incorrect trigger of the interrupt. Revert "dt-bindings: pinctrl-zynqmp: Add output-enable configuration" Revert "pinctrl: pinctrl-zynqmp: Add support for output-enable and bias-high-impedance" pinctrl: qcom: Avoid glitching lines when we first mux to output pinctrl: Ingenic: JZ4755 bug fixes
-
Jakub Kicinski authored
As Shakeel explains the commit under Fixes had the unintended side-effect of no longer pre-loading the cached memory allowance. Even tho we previously dropped the first packet received when over memory limit - the consecutive ones would get thru by using the cache. The charging was happening in batches of 128kB, so we'd let in 128kB (truesize) worth of packets per one drop. After the change we no longer force charge, there will be no cache filling side effects. This causes significant drops and connection stalls for workloads which use a lot of page cache, since we can't reclaim page cache under GFP_NOWAIT. Some of the latency can be recovered by improving SACK reneg handling but nowhere near enough to get back to the pre-5.15 performance (the application I'm experimenting with still sees 5-10x worst latency). Apply the suggested workaround of using GFP_ATOMIC. We will now be more permissive than previously as we'll drop _no_ packets in softirq when under pressure. But I can't think of any good and simple way to address that within networking. Link: https://lore.kernel.org/all/20221012163300.795e7b86@kernel.org/Suggested-by:
Shakeel Butt <shakeelb@google.com> Fixes: 4b1327be ("net-memcg: pass in gfp_t mask to mem_cgroup_charge_skmem()") Acked-by:
Roman Gushchin <roman.gushchin@linux.dev> Link: https://lore.kernel.org/r/20221021160304.1362511-1-kuba@kernel.orgSigned-off-by:
-
Neal Cardwell authored
This commit fixes a bug that can cause a TCP data sender to repeatedly defer RTOs when encountering SACK reneging. The bug is that when we're in fast recovery in a scenario with SACK reneging, every time we get an ACK we call tcp_check_sack_reneging() and it can note the apparent SACK reneging and rearm the RTO timer for srtt/2 into the future. In some SACK reneging scenarios that can happen repeatedly until the receive window fills up, at which point the sender can't send any more, the ACKs stop arriving, and the RTO fires at srtt/2 after the last ACK. But that can take far too long (O(10 secs)), since the connection is stuck in fast recovery with a low cwnd that cannot grow beyond ssthresh, even if more bandwidth is available. This fix changes the logic in tcp_check_sack_reneging() to only rearm the RTO timer if data is cumulatively ACKed, indicating forward progress. This avoids this kind of nearly infinite loop of RTO timer re-arming. In addition, this meets the goals of tcp_check_sack_reneging() in handling Windows TCP behavior that looks temporarily like SACK reneging but is not really. Many thanks to Jakub Kicinski and Neil Spring, who reported this issue and provided critical packet traces that enabled root-causing this issue. Also, many thanks to Jakub Kicinski for testing this fix. Fixes: 5ae344c9 ("tcp: reduce spurious retransmits due to transient SACK reneging") Reported-by:
Neil Spring <ntspring@fb.com> Signed-off-by:
Neal Cardwell <ncardwell@google.com> Reviewed-by:
-
https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpfJakub Kicinski authored
Alexei Starovoitov says: ==================== pull-request: bpf 2022-10-23 We've added 7 non-merge commits during the last 18 day(s) which contain a total of 8 files changed, 69 insertions(+), 5 deletions(-). The main changes are: 1) Wait for busy refill_work when destroying bpf memory allocator, from Hou. 2) Allow bpf_user_ringbuf_drain() callbacks to return 1, from David. 3) Fix dispatcher patchable function entry to 5 bytes nop, from Jiri. 4) Prevent decl_tag from being referenced in func_proto, from Stanislav. * tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf: bpf: Use __llist_del_all() whenever possbile during memory draining bpf: Wait for busy refill_work when destroying bpf memory allocator bpf: Fix dispatcher patchable function entry to 5 bytes nop bpf: prevent decl_tag from being referenced in func_proto selftests/bpf: Add reproducer for decl_tag in func_proto return type selftests/bpf: Make bpf_user_ringbuf_drain() selftest callback return 1 bpf: Allow bpf_user_ringbuf_drain() callbacks to return 1 ==================== Link: https://lore.kernel.org/r/20221023192244.81137-1-alexei.starovoitov@gmail.comSigned-off-by:
-
Lu Wei authored
The type of sk_rcvbuf and sk_sndbuf in struct sock is int, and in tcp_add_backlog(), the variable limit is caculated by adding sk_rcvbuf, sk_sndbuf and 64 * 1024, it may exceed the max value of int and overflow. This patch reduces the limit budget by halving the sndbuf to solve this issue since ACK packets are much smaller than the payload. Fixes: c9c33212 ("tcp: add tcp_add_backlog()") Signed-off-by:
Lu Wei <luwei32@huawei.com> Reviewed-by:
Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by:
-
Zhang Changzhong authored
The ndo_start_xmit() method must not free skb when returning NETDEV_TX_BUSY, since caller is going to requeue freed skb. Fixes: 504d4721 ("MIPS: Lantiq: Add ethernet driver") Signed-off-by:
Zhang Changzhong <zhangchangzhong@huawei.com> Signed-off-by:
-
Zhengchao Shao authored
When the ops_init() interface is invoked to initialize the net, but ops->init() fails, data is released. However, the ptr pointer in net->gen is invalid. In this case, when nfqnl_nf_hook_drop() is invoked to release the net, invalid address access occurs. The process is as follows: setup_net() ops_init() data = kzalloc(...) ---> alloc "data" net_assign_generic() ---> assign "date" to ptr in net->gen ... ops->init() ---> failed ... kfree(data); ---> ptr in net->gen is invalid ... ops_exit_list() ... nfqnl_nf_hook_drop() *q = nfnl_queue_pernet(net) ---> q is invalid The following is the Call Trace information: BUG: KASAN: use-after-free in nfqnl_nf_hook_drop+0x264/0x280 Read of size 8 at addr ffff88810396b240 by task ip/15855 Call Trace: <TASK> dump_stack_lvl+0x8e/0xd1 print_report+0x155/0x454 kasan_report+0xba/0x1f0 nfqnl_nf_hook_drop+0x264/0x280 nf_queue_nf_hook_drop+0x8b/0x1b0 __nf_unregister_net_hook+0x1ae/0x5a0 nf_unregister_net_hooks+0xde/0x130 ops_exit_list+0xb0/0x170 setup_net+0x7ac/0xbd0 copy_net_ns+0x2e6/0x6b0 create_new_namespaces+0x382/0xa50 unshare_nsproxy_namespaces+0xa6/0x1c0 ksys_unshare+0x3a4/0x7e0 __x64_sys_unshare+0x2d/0x40 do_syscall_64+0x35/0x80 entry_SYSCALL_64_after_hwframe+0x46/0xb0 </TASK> Allocated by task 15855: kasan_save_stack+0x1e/0x40 kasan_set_track+0x21/0x30 __kasan_kmalloc+0xa1/0xb0 __kmalloc+0x49/0xb0 ops_init+0xe7/0x410 setup_net+0x5aa/0xbd0 copy_net_ns+0x2e6/0x6b0 create_new_namespaces+0x382/0xa50 unshare_nsproxy_namespaces+0xa6/0x1c0 ksys_unshare+0x3a4/0x7e0 __x64_sys_unshare+0x2d/0x40 do_syscall_64+0x35/0x80 entry_SYSCALL_64_after_hwframe+0x46/0xb0 Freed by task 15855: kasan_save_stack+0x1e/0x40 kasan_set_track+0x21/0x30 kasan_save_free_info+0x2a/0x40 ____kasan_slab_free+0x155/0x1b0 slab_free_freelist_hook+0x11b/0x220 __kmem_cache_free+0xa4/0x360 ops_init+0xb9/0x410 setup_net+0x5aa/0xbd0 copy_net_ns+0x2e6/0x6b0 create_new_namespaces+0x382/0xa50 unshare_nsproxy_namespaces+0xa6/0x1c0 ksys_unshare+0x3a4/0x7e0 __x64_sys_unshare+0x2d/0x40 do_syscall_64+0x35/0x80 entry_SYSCALL_64_after_hwframe+0x46/0xb0 Fixes: f875bae0 ("net: Automatically allocate per namespace data.") Signed-off-by:
Zhengchao Shao <shaozhengchao@huawei.com> Signed-off-by:
-
Jakub Kicinski authored
Some of us gotten used to producing large quantities of peer feedback at work, every 3 or 6 months. Extending the same courtesy to community members seems like a logical step. It may be hard for some folks to get validation of how important their work is internally, especially at smaller companies which don't employ many kernel experts. The concept of "peer feedback" may be a hyperscaler / silicon valley thing so YMMV. Hopefully we can build more context as we go. Signed-off-by:
-
David S. Miller authored
Eric Dumazet says: ==================== kcm: annotate data-races This series address two different syzbot reports for KCM. ==================== Signed-off-by: -
Eric Dumazet authored
kcm->rx_psock can be read locklessly in kcm_rfree(). Annotate the read and writes accordingly. syzbot reported: BUG: KCSAN: data-race in kcm_rcv_strparser / kcm_rfree write to 0xffff88810784e3d0 of 1 bytes by task 1823 on cpu 1: reserve_rx_kcm net/kcm/kcmsock.c:283 [inline] kcm_rcv_strparser+0x250/0x3a0 net/kcm/kcmsock.c:363 __strp_recv+0x64c/0xd20 net/strparser/strparser.c:301 strp_recv+0x6d/0x80 net/strparser/strparser.c:335 tcp_read_sock+0x13e/0x5a0 net/ipv4/tcp.c:1703 strp_read_sock net/strparser/strparser.c:358 [inline] do_strp_work net/strparser/strparser.c:406 [inline] strp_work+0xe8/0x180 net/strparser/strparser.c:415 process_one_work+0x3d3/0x720 kernel/workqueue.c:2289 worker_thread+0x618/0xa70 kernel/workqueue.c:2436 kthread+0x1a9/0x1e0 kernel/kthread.c:376 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:306 read to 0xffff88810784e3d0 of 1 bytes by task 17869 on cpu 0: kcm_rfree+0x121/0x220 net/kcm/kcmsock.c:181 skb_release_head_state+0x8e/0x160 net/core/skbuff.c:841 skb_release_all net/core/skbuff.c:852 [inline] __kfree_skb net/core/skbuff.c:868 [inline] kfree_skb_reason+0x5c/0x260 net/core/skbuff.c:891 kfree_skb include/linux/skbuff.h:1216 [inline] kcm_recvmsg+0x226/0x2b0 net/kcm/kcmsock.c:1161 ____sys_recvmsg+0x16c/0x2e0 ___sys_recvmsg net/socket.c:2743 [inline] do_recvmmsg+0x2f1/0x710 net/socket.c:2837 __sys_recvmmsg net/socket.c:2916 [inline] __do_sys_recvmmsg net/socket.c:2939 [inline] __se_sys_recvmmsg net/socket.c:2932 [inline] __x64_sys_recvmmsg+0xde/0x160 net/socket.c:2932 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x2b/0x70 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x63/0xcd value changed: 0x01 -> 0x00 Reported by Kernel Concurrency Sanitizer on: CPU: 0 PID: 17869 Comm: syz-executor.2 Not tainted 6.1.0-rc1-syzkaller-00010-gbb1a1146-dirty #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/22/2022 Fixes: ab7ac4eb ("kcm: Kernel Connection Multiplexor module") Reported-by:
-
