The CPSW switch can act as Dual EMAC by segregating the switch ports
using VLAN and port VLAN as per the TRM description in
14.3.2.10.2 Dual Mac Mode

Following CPSW components will be common for both the interfaces.
* Interrupt source is common for both eth interfaces
* Interrupt pacing is common for both interfaces
* Hardware statistics is common for all the ports
* CPDMA is common for both eth interface
* CPTS is common for both the interface and it should not be enabled on
  both the interface as timestamping information doesn't contain port
  information.

Constrains
* Reserved VID of One port should not be used in other interface which will
  enable switching functionality
* Same VID must not be used in both the interface which will enable switching
  functionality
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As CPTS is common module for both EMAC in Dual EMAC mode so making cpts as
pointer.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* Introduced parameter to add port number for directed packet in cpdma_chan_submit
* Source port detection macro with DMA descriptor status
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vlad says: The whole multiple cookie keys code is completely unused
and has been all this time. Noone uses anything other then the
secret_key[0] since there is no changeover support anywhere.

Thus, for now clean up its left-over fragments.

Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With my recent commit I introduced two sparse warnings.  Looking closer there
were a few more in the same file, so I fixed them all up.  Basic rcu pointer
dereferencing suff.

I've validated these changes using CONFIG_PROVE_RCU while starting and stopping
netconsole repeatedly in bonded and non-bonded configurations
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: fengguang.wu@intel.com
CC: David Miller <davem@davemloft.net>
CC: eric.dumazet@gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>

__netpoll_rcu_free is used to free netpoll structures when the rtnl_lock is
already held.  The mechanism is used to asynchronously call __netpoll_cleanup
outside of the holding of the rtnl_lock, so as to avoid deadlock.
Unfortunately, __netpoll_cleanup modifies pointers (dev->np), which means the
rtnl_lock must be held while calling it.  Further, it cannot be held, because
rcu callbacks may be issued in softirq contexts, which cannot sleep.

Fix this by converting the rcu callback to a work queue that is guaranteed to
get scheduled in process context, so that we can hold the rtnl properly while
calling __netpoll_cleanup

Tested successfully by myself.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Cong Wang <amwang@redhat.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Create skb_panic() function in lieu of both skb_over_panic() and
skb_under_panic() so that code duplication would be avoided. Update type
and variable name where necessary.

Jiri Pirko suggested using wrappers so that we would be able to keep the
fruits of the original code.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sparse spotted local function that could be static.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes sparse complaints about dropping __user in casts.
 warning: cast removes address space of expression
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

And remove no longer used br->flags.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cc: Erik Hugne <erik.hugne@ericsson.com>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

v2:
a) moved before multicast source address check
b) changed comment to netdev style

Cc: Erik Hugne <erik.hugne@ericsson.com>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reported-by: Erik Hugne <erik.hugne@ericsson.com>
Cc: Erik Hugne <erik.hugne@ericsson.com>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

o Do not read mailbox registers on timeout
o Add a helper function to handle mailbox response
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o Handle async events during diagnostic loopback test
o Clear loopback mode on failure to receive async events
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cleanly separate 83xx diagnostic IRQ test from 82xx
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cleanly separate 83xx diagnostic loopback test routines from 82xx
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Create a helper routine to handle async events, as it is being called
from multiple places
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Driver needs to stop participating in firmware based Inter Driver
Communication (IDC) while unloading driver
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Register for firmware based Inter Driver Communication (IDC) using initialize
NIC as the first mailbox command
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To allow both of protocol-specific data and device-specific data
attached with neighbour entry, and to eliminate size calculation
cost when allocating entry, sizeof protocol-speicic data must be
multiple of NEIGH_PRIV_ALIGN.  On 64bit archs,
sizeof(struct dn_neigh) is multiple of NEIGH_PRIV_ALIGN, but on
32bit archs, it was not.

Introduce NEIGH_ENTRY_SPACE() macro to ensure that protocol-specific
entry-size meets our requirement.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

RFC4291 (IPv6 addressing architecture) says that interface-Local scope
spans only a single interface on a node.  We should not join L2 device
multicast list for addresses in interface-local (or smaller) scope.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit d0e2c55e (veth: avoid a NULL deref in veth_stats_one)
added another NULL deref in veth_dellink().

# ip link add name veth1 type veth peer name veth0
# rmmod veth

We crash because veth_dellink() is called twice, so we must
take care of NULL peer.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

David Ward says:

====================
The Linux kernel currently implements the GARP VLAN Registration
Protocol (GVRP) from IEEE 802.1Q-1998 (applicant-only participant).
When the GVRP flag is set for a VLAN interface on a Linux host, the
host advertises its membership in the VLAN to the attached bridge/
switch, so that it is not necessary to manually configure the bridge/
switch port to participate in the VLAN.

GVRP has been superseded by the Multiple VLAN Registration Protocol
(MVRP) in IEEE 802.1Q-2011, which addresses scalability concerns about
the earlier protocol.  The following patches add support for MVRP to
the Linux kernel and iproute2 utility. They are based largely off of
the existing implementation of GVRP, but have been modified for the
new PDU structure and state machine.

This implementation was tested with two Juniper EX4200 switches.
====================
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Initial implementation of the Multiple VLAN Registration Protocol
(MVRP) from IEEE 802.1Q-2011, based on the existing implementation
of the GARP VLAN Registration Protocol (GVRP).
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Initial implementation of the Multiple Registration Protocol (MRP)
from IEEE 802.1Q-2011, based on the existing implementation of the
Generic Attribute Registration Protocol (GARP).
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andy King says:

====================
In an effort to improve the out-of-the-box experience with Linux kernels for
VMware users, VMware is working on readying the VM Sockets (VSOCK, formerly
VMCI Sockets) (vsock) kernel module for inclusion in the Linux kernel. The
purpose of this post is to acquire feedback on the vsock kernel module.

Unlike previous submissions, where the new socket family was entirely reliant
on VMware's VMCI PCI device (and thus VMware's hypervisor), VM Sockets is now
completely[1] separated out into two parts, each in its own module:

o Core socket code, which is transport-neutral and invokes transport
  callbacks to communicate with the hypervisor.  This is vsock.ko.
o A VMCI transport, which communicates over VMCI with the VMware hypervisor.
  This is vmw_vsock_vmci_transport.ko, and it registers with the core module
  as a transport.

This should provide a path to introducing additional transports, for example
virtio, with the ultimate goal being to make this new socket family
hypervisor-neutral.

[1] If Gerd tries it and determines this to be false (still), I'll ship him
    a keg of beer.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

VM Sockets allows communication between virtual machines and the hypervisor.
User level applications both in a virtual machine and on the host can use the
VM Sockets API, which facilitates fast and efficient communication between
guest virtual machines and their host.  A socket address family, designed to be
compatible with UDP and TCP at the interface level, is provided.

Today, VM Sockets is used by various VMware Tools components inside the guest
for zero-config, network-less access to VMware host services.  In addition to
this, VMware's users are using VM Sockets for various applications, where
network access of the virtual machine is restricted or non-existent.  Examples
of this are VMs communicating with device proxies for proprietary hardware
running as host applications and automated testing of applications running
within virtual machines.

The VMware VM Sockets are similar to other socket types, like Berkeley UNIX
socket interface.  The VM Sockets module supports both connection-oriented
stream sockets like TCP, and connectionless datagram sockets like UDP. The VM
Sockets protocol family is defined as "AF_VSOCK" and the socket operations
split for SOCK_DGRAM and SOCK_STREAM.

For additional information about the use of VM Sockets, please refer to the
VM Sockets Programming Guide available at:

https://www.vmware.com/support/developer/vmci-sdk/Signed-off-by: George Zhang <georgezhang@vmware.com>
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Andy king <acking@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Synchronize with 'net' in order to sort out some l2tp, wireless, and
ipv6 GRE fixes that will be built on top of in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>

This was preventing GRO and RxCheckSum offload to happen.
Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In sctp_auth_make_key_vector, we allocate a temporary sctp_auth_bytes
structure with kmalloc instead of the sctp_auth_create_key allocator.
Change this to sctp_auth_create_key as it is the case everywhere else,
so that we also can properly free it via sctp_auth_key_put. This makes
it easier for future code changes in the structure and allocator itself,
since a single API is consistently used for this purpose. Also, by
using sctp_auth_create_key we're doing sanity checks over the arguments.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some multicast addresses are common to all macvlans,
so if a multicast message has a hash value collision, we
have to deliver a copy to all macvlans, adding significant
latency and possible packet drops if netdev_max_backlog
limit is hit.

Having a per macvlan hash function permits to reduce the
impact of hash collisions.
Suggested-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit cd431e73 (macvlan: add multicast filter) forgot
the broadcast case.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Maciej Żenczykowski <maze@google.com>
SIgned-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes the following RCU warning:

[   51.680236] ===============================
[   51.681914] [ INFO: suspicious RCU usage. ]
[   51.683610] 3.8.0-rc6-next-20130206-sasha-00028-g83214f7-dirty #276 Tainted: G        W
[   51.686703] -------------------------------
[   51.688281] net/ipv6/ip6_flowlabel.c:671 suspicious rcu_dereference_check() usage!

we should use rcu_dereference_bh() when we hold rcu_read_lock_bh().
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

alloc failures already get standardized OOM
messages and a dump_stack.

For the affected mallocs around these OOM messages:

Converted kmallocs with multiplies to kmalloc_array.
Converted a kmalloc/memcpy to kmemdup.
Removed now unused stack variables.
Removed unnecessary parentheses.
Neatened alignment.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The last (bool) parameter in bgmac_cmdcfg_maskset says if the write
should be made, even if value didn't change. Currently driver doesn't
match the specs about (not) forcing some changes. This makes it follow
them.
Reported-by: Nathan Hintz <nlhintz@hotmail.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds check for a valid Ethernet MAC address and in case it is not,
it will generate a valid random one, such that the adapter is still
usable.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to address the fact that some devices cannot support the full 32K
frag size we need to have the value accessible somewhere so that we can use it
to do comparisons against what the device can support.  As such I am moving
the values out of skbuff.c and into skbuff.h.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>