When an internal error condition is detected, make sure to set the
device inactive after dispatching the event so ULPs can get a
notification of this event.

Fixes: e126ba97 ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

When calling reg_mr of large MRs (e.g. 4GB) from multiple processes
and MR caches can't supply the required amount of MRs the slow-path
of MR allocation may be used. In this case we need to serialize the
slow-path between the processes to avoid soft lock.

Fixes: e126ba97 ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Moshe Lazer <moshel@mellanox.com>
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

When creating kernel CQs use 128B CQE stride if the
cache line size is 128B, 64B otherwise.  This prevents
multiple CQEs from residing in a 128B cache line,
which can cause retries when there are concurrent
read and writes in one cache line.

Tested with IPoIB on PPC64, saw ~5% throughput
improvement.

Fixes: e126ba97 ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Validate that the requested size of RQT is supported by firmware.

Fixes: c5f90929 ('IB/mlx5: Add Receive Work Queue Indirection table operations')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

We need to free dev->port when we fail to enable RoCE or
initialize node data.

Fixes: 0837e86a ('IB/mlx5: Add per port counters')
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

sg_alloc_table gets unsigned int as parameter while the driver
returns it as size_t. Check npages isn't greater than maximum
unsigned int.

Fixes: eeb8461e ("IB: Refactor umem to use linear SG table")
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

When calling rdma_resolve_ip inside rdma_addr_find_l2_eth_by_grh,
the return status of the request was ignored in the callback function
causing a successful return and an empty dmac.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

On Thu, Oct 27, 2016 at 04:36:28PM +0300, Leon Romanovsky wrote:
> From: Mark Bloch <markb@mellanox.com>
>
> If the underlying netowrk type is ipv4 or ipv6 and the device supports
> routable RoCE, prefer it so the traffic could cross subnets.
>
> Signed-off-by: Mark Bloch <markb@mellanox.com>
> Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
> Signed-off-by: Leon Romanovsky <leon@kernel.org>
> ---

Hi Doug,

Please take the following v1 of this patch where I fixed spelling error
from "netowrk" to be "network".

Thanks.

>From 09f96ba3e9b4442cfb44dca04c6726e55525c9c3 Mon Sep 17 00:00:00 2001
From: Mark Bloch <markb@mellanox.com>
Date: Sun, 11 Sep 2016 06:25:10 +0000
Subject: [PATCH rdma-rc v1 3/6] IB/core: Set routable RoCE gid type for ipv4/ipv6
 networks

If the underlying network type is ipv4 or ipv6 and the device supports
routable RoCE, prefer it so the traffic could cross subnets.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

When there is a CM id object that has port assigned to it, it means that
the cm-id asked for the specific port that it should go by it, but if
that port was removed (hot-unplug event) the cm-id was not updated.
In order to fix that the port keeps a list of all the cm-id's that are
planning to go by it, whenever the port is removed it marks all of them
as invalid.

This commit fixes a kernel panic which happens when running traffic between
guests and we force reboot a guest mid traffic, it triggers a kernel panic:

 Call Trace:
  [<ffffffff815271fa>] ? panic+0xa7/0x16f
  [<ffffffff8152b534>] ? oops_end+0xe4/0x100
  [<ffffffff8104a00b>] ? no_context+0xfb/0x260
  [<ffffffff81084db2>] ? del_timer_sync+0x22/0x30
  [<ffffffff8104a295>] ? __bad_area_nosemaphore+0x125/0x1e0
  [<ffffffff81084240>] ? process_timeout+0x0/0x10
  [<ffffffff8104a363>] ? bad_area_nosemaphore+0x13/0x20
  [<ffffffff8104aabf>] ? __do_page_fault+0x31f/0x480
  [<ffffffff81065df0>] ? default_wake_function+0x0/0x20
  [<ffffffffa0752675>] ? free_msg+0x55/0x70 [mlx5_core]
  [<ffffffffa0753434>] ? cmd_exec+0x124/0x840 [mlx5_core]
  [<ffffffff8105a924>] ? find_busiest_group+0x244/0x9f0
  [<ffffffff8152d45e>] ? do_page_fault+0x3e/0xa0
  [<ffffffff8152a815>] ? page_fault+0x25/0x30
  [<ffffffffa024da25>] ? cm_alloc_msg+0x35/0xc0 [ib_cm]
  [<ffffffffa024e821>] ? ib_send_cm_dreq+0xb1/0x1e0 [ib_cm]
  [<ffffffffa024f836>] ? cm_destroy_id+0x176/0x320 [ib_cm]
  [<ffffffffa024fb00>] ? ib_destroy_cm_id+0x10/0x20 [ib_cm]
  [<ffffffffa034f527>] ? ipoib_cm_free_rx_reap_list+0xa7/0x110 [ib_ipoib]
  [<ffffffffa034f590>] ? ipoib_cm_rx_reap+0x0/0x20 [ib_ipoib]
  [<ffffffffa034f5a5>] ? ipoib_cm_rx_reap+0x15/0x20 [ib_ipoib]
  [<ffffffff81094d20>] ? worker_thread+0x170/0x2a0
  [<ffffffff8109b2a0>] ? autoremove_wake_function+0x0/0x40
  [<ffffffff81094bb0>] ? worker_thread+0x0/0x2a0
  [<ffffffff8109aef6>] ? kthread+0x96/0xa0
  [<ffffffff8100c20a>] ? child_rip+0xa/0x20
  [<ffffffff8109ae60>] ? kthread+0x0/0xa0
  [<ffffffff8100c200>] ? child_rip+0x0/0x20

Fixes: a977049d ("[PATCH] IB: Add the kernel CM implementation")
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

The real QP is destroyed in case of the ref count reaches zero, but
for XRC target QPs this call was missed and caused to QP leaks.

Let's call to destroy for all flows.

Fixes: 0e0ec7e0 ('RDMA/core: Export ib_open_qp() to share XRC...')
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Pull x86 bugfix from Thomas Gleixner:
 "A single bugfix for the recent changes related to registering the boot
  cpu when this has not happened before prefill_possible_map().

  The main problem with this change got fixed already, but we missed the
  case where the local APIC is not yet mapped, when prefill_possible_map()
  is invoked, so the registration of the boot cpu which has the APIC bit
  set in CPUID will explode.

  I should have seen that issue earlier, but all I can do now is feeling
  embarassed"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/smpboot: Init apic mapping before usage

Pull ubi/ubifs fixes from Richard Weinberger:
 "This contains fixes for issues in both UBI and UBIFS:

   - A regression wrt overlayfs, introduced in -rc2.
   - An UBI issue, found by Dan Carpenter's static checker"

* tag 'upstream-4.9-rc3' of git://git.infradead.org/linux-ubifs:
  ubifs: Fix regression in ubifs_readdir()
  ubi: fastmap: Fix add_vol() return value test in ubi_attach_fastmap()

Pull ARM SoC fixes from Olof Johansson:
 "We haven't seen a whole lot of fixes for the first two weeks since the
  merge window, but here is the batch that we have at the moment.

  Nothing sticks out as particularly bad or scary, it's mostly a handful
  of smaller fixes to several platforms. The Uniphier reset controller
  changes could probably have been delayed to 4.10, but they're not
  scary and just plumbing up driver changes that went in during the
  merge window.

  We're also adding another maintainer to Marvell Berlin platforms, to
  help out when Sebastian is too busy. Yay teamwork!"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: imx: mach-imx6q: Fix the PHY ID mask for AR8031
  ARM: dts: vf610: fix IRQ flag of global timer
  ARM: imx: gpc: Fix the imx_gpc_genpd_init() error path
  ARM: imx: gpc: Initialize all power domains
  arm64: dts: Updated NAND DT properties for NS2 SVK
  arm64: dts: uniphier: change MIO node to SD control node
  ARM: dts: uniphier: change MIO node to SD control node
  reset: uniphier: rename MIO reset to SD reset for Pro5, PXs2, LD20 SoCs
  arm64: uniphier: select ARCH_HAS_RESET_CONTROLLER
  ARM: uniphier: select ARCH_HAS_RESET_CONTROLLER
  arm64: dts: Add timer erratum property for LS2080A and LS1043A
  arm64: dts: rockchip: remove the abuse of keep-power-in-suspend
  ARM: multi_v7_defconfig: Enable Intel e1000e driver
  MAINTAINERS: add myself as Marvell berlin SoC maintainer
  bus: qcom-ebi2: depend on ARCH_QCOM or COMPILE_TEST
  ARM: dts: fix the SD card on the Snowball
  arm64: dts: rockchip: remove always-on and boot-on from vcc_sd
  arm64: dts: marvell: fix clocksource for CP110 master SPI0
  ARM: mvebu: Select corediv clk for all mvebu v7 SoC

Pull char/misc driver fixes from Greg KH:
 "Here are a few small char/misc driver fixes for reported issues.

  The "biggest" are two binder fixes for reported issues that have been
  shipping in Android phones for a while now, the others are various
  fixes for reported problems.

  And there's a MAINTAINERS update for good measure.

  All have been in linux-next with no reported issues"

* tag 'char-misc-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  MAINTAINERS: Add entry for genwqe driver
  VMCI: Doorbell create and destroy fixes
  GenWQE: Fix bad page access during abort of resource allocation
  vme: vme_get_size potentially returning incorrect value on failure
  extcon: qcom-spmi-misc: Sync the extcon state on interrupt
  hv: do not lose pending heartbeat vmbus packets
  mei: txe: don't clean an unprocessed interrupt cause.
  ANDROID: binder: Clear binder and cookie when setting handle in flat binder struct
  ANDROID: binder: Add strong ref checks

Merge tag 'v4.9-rockchip-dts64-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes

Correct regulator handling on Rockchip arm64 boards to make
bind/unbind calls work correctly and remove a sdio-only
property from non-sdio mmc hosts, that accidentially was
added there.

* tag 'v4.9-rockchip-dts64-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  arm64: dts: rockchip: remove the abuse of keep-power-in-suspend
  arm64: dts: rockchip: remove always-on and boot-on from vcc_sd
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'arm-soc/for-4.9/devicetree-arm64-fixes' of http://github.com/Broadcom/stblinux into fixes

This pull request contains a single fix for Broadcom ARM64-based SoCs:

- Ray adds the required bus width and OOB sector size properties to the
  Northstar 2 SVK reference board in order for the NAND controller to work
  properly

* tag 'arm-soc/for-4.9/devicetree-arm64-fixes' of http://github.com/Broadcom/stblinux:
  arm64: dts: Updated NAND DT properties for NS2 SVK
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'imx-fixes-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes

The i.MX fixes for 4.9:
 - A couple of patches from Fabio to fix the GPC power domain regression
   which is caused by PM Domain core change 0159ec67
   ("PM / Domains: Verify the PM domain is present when adding a
   provider"), and a related kernel crash seen with multi_v7_defconfig
   build.
 - Correct the PHY ID mask for AR8031 to match phy driver code.
 - Apply new added timer erratum A008585 for LS1043A and LS2080A SoC.
 - Correct vf610 global timer IRQ flag to avoid warning from gic driver
   after commit 992345a5 ("irqchip/gic: WARN if setting the
   interrupt type for a PPI fails").

* tag 'imx-fixes-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: imx: mach-imx6q: Fix the PHY ID mask for AR8031
  ARM: dts: vf610: fix IRQ flag of global timer
  ARM: imx: gpc: Fix the imx_gpc_genpd_init() error path
  ARM: imx: gpc: Initialize all power domains
  arm64: dts: Add timer erratum property for LS2080A and LS1043A
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'uniphier-fixes-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into fixes

UniPhier ARM SoC fixes for v4.9

- Add "select ARCH_HAS_RESET_CONTROLLER" in Kconfig
- Rename wrongly-named mioctrl to sdctrl

* tag 'uniphier-fixes-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
  arm64: dts: uniphier: change MIO node to SD control node
  ARM: dts: uniphier: change MIO node to SD control node
  reset: uniphier: rename MIO reset to SD reset for Pro5, PXs2, LD20 SoCs
  arm64: uniphier: select ARCH_HAS_RESET_CONTROLLER
  ARM: uniphier: select ARCH_HAS_RESET_CONTROLLER
Signed-off-by: Olof Johansson <olof@lixom.net>

Pull driver core fixes from Greg KH:
 "Here are two small driver core / kernfs fixes for 4.9-rc3.

  One makes the Kconfig entry for DEBUG_TEST_DRIVER_REMOVE a bit more
  explicit that this is a crazy thing to enable for a distro kernel
  (thanks for trying Fedora!), the other resolves an issue with vim
  opening kernfs files (sysfs, configfs, etc.)

  Both have been in linux-next with no reported issues"

* tag 'driver-core-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  driver core: Make Kconfig text for DEBUG_TEST_DRIVER_REMOVE stronger
  kernfs: Add noop_fsync to supported kernfs_file_fops

Pull staging and IIO driver fixes from Greg KH:
 "Here are some small staging and iio driver fixes for reported issues
  for 4.9-rc3. Nothing major, the "largest" being a lustre fix for a
  sysfs file that was obviously wrong, and had never been tested, so it
  was moved to debugfs as that is where it belongs. The others are small
  bug fixes for reported issues with various staging or iio drivers.

  All have been in linux-next for a while with no reported issues"

* tag 'staging-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  greybus: fix a leak on error in gb_module_create()
  greybus: es2: fix error return code in ap_probe()
  greybus: arche-platform: Add missing of_node_put() in arche_platform_change_state()
  staging: android: ion: Fix error handling in ion_query_heaps()
  iio: accel: sca3000_core: avoid potentially uninitialized variable
  iio:chemical:atlas-ph-sensor: Fix use of 32 bit int to hold 16 bit big endian value
  staging/lustre/llite: Move unstable_stats from sysfs to debugfs
  Staging: wilc1000: Fix kernel Oops on opening the device
  staging: android/ion: testing the wrong variable
  Staging: greybus: uart: Use gbphy_dev->dev instead of bundle->dev
  Staging: greybus: gpio: Use gbphy_dev->dev instead of bundle->dev
  iio: adc: ti-adc081c: Select IIO_TRIGGERED_BUFFER to prevent build errors
  iio: maxim_thermocouple: Align 16 bit big endian value of raw reads

Pull tty/serial driver fixes from Greg KH:
 "Here are a number of small tty and serial driver fixes for reported
  issues for 4.9-rc3. Nothing major, but they do resolve a bunch of
  problems with the tty core changes that are in 4.9-rc1, and finally
  the atmel serial driver is back working properly.

  All have been in linux-next with no reported issues"

* tag 'tty-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: serial_core: fix NULL struct tty pointer access in uart_write_wakeup
  tty: serial_core: Fix serial console crash on port shutdown
  tty/serial: at91: fix hardware handshake on Atmel platforms
  vt: clear selection before resizing
  sc16is7xx: always write state when configuring GPIO as an output
  sh-sci: document R8A7743/5 support
  tty: serial: 8250: 8250_core: NXP SC16C2552 workaround
  tty: limit terminal size to 4M chars
  tty: serial: fsl_lpuart: Fix Tx DMA edge case
  serial: 8250_lpss: enable MSI for sure
  serial: core: fix console problems on uart_close
  serial: 8250_uniphier: fix clearing divisor latch access bit
  serial: 8250_uniphier: fix more unterminated string
  serial: pch_uart: add terminate entry for dmi_system_id tables
  devicetree: bindings: uart: Add new compatible string for ZynqMP
  serial: xuartps: Add new compatible string for ZynqMP
  serial: SERIAL_STM32 should depend on HAS_DMA
  serial: stm32: Fix comparisons with undefined register
  tty: vt, fix bogus division in csi_J

Pull USB fixes from Greg KH:
 "Here are a number of small USB driver fixes for 4.9-rc3.

  There is the usual number of gadget and xhci patches in here to
  resolved reported issues, as well as some usb-serial driver fixes and
  new device ids.

  All have been in linux-next with no reported issues"

* tag 'usb-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (26 commits)
  usb: chipidea: host: fix NULL ptr dereference during shutdown
  usb: renesas_usbhs: add wait after initialization for R-Car Gen3
  usb: increase ohci watchdog delay to 275 msec
  usb: musb: Call pm_runtime from musb_gadget_queue
  usb: musb: Fix hardirq-safe hardirq-unsafe lock order error
  usb: ehci-platform: increase EHCI_MAX_RSTS to 4
  usb: ohci-at91: Set RemoteWakeupConnected bit explicitly.
  USB: serial: fix potential NULL-dereference at probe
  xhci: use default USB_RESUME_TIMEOUT when resuming ports.
  xhci: workaround for hosts missing CAS bit
  xhci: add restart quirk for Intel Wildcatpoint PCH
  USB: serial: cp210x: fix tiocmget error handling
  wusb: fix error return code in wusb_prf()
  Revert "Documentation: devicetree: dwc2: Deprecate g-tx-fifo-size"
  Revert "usb: dwc2: gadget: fix TX FIFO size and address initialization"
  Revert "usb: dwc2: gadget: change variable name to more meaningful"
  USB: serial: ftdi_sio: add support for Infineon TriBoard TC2X7
  wusb: Stop using the stack for sg crypto scratch space
  usb: dwc3: Fix size used in dma_free_coherent()
  usb: gadget: f_fs: stop sleeping in ffs_func_eps_disable
  ...

The recent changes, which forced the registration of the boot cpu on UP
systems, which do not have ACPI tables, have been fixed for systems w/o
local APIC, but left a wreckage for systems which have neither ACPI nor
mptables, but the CPU has an APIC, e.g. virtualbox.

The boot process crashes in prefill_possible_map() as it wants to register
the boot cpu, which needs to access the local apic, but the local APIC is
not yet mapped.

There is no reason why init_apic_mapping() can't be invoked before
prefill_possible_map(). So instead of playing another silly early mapping
game, as the ACPI/mptables code does, we just move init_apic_mapping()
before the call to prefill_possible_map().

In hindsight, I should have noticed that combination earlier.

Sorry for the churn (also in stable)!

Fixes: ff856051 ("x86/boot/smp: Don't try to poke disabled/non-existent APIC")
Reported-and-debugged-by: Michal Necasek <michal.necasek@oracle.com>
Reported-and-tested-by: Wolfgang Bauer <wbauer@tmo.at>
Cc: prarit@redhat.com
Cc: ville.syrjala@linux.intel.com
Cc: michael.thayer@oracle.com
Cc: knut.osmundsen@oracle.com
Cc: frank.mehnert@oracle.com
Cc: Borislav Petkov <bp@alien8.de>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1610282114380.5053@nanosSigned-off-by: Thomas Gleixner <tglx@linutronix.de>

Pull ACPI fixes from Rafael Wysocki:
 "These fix recent ACPICA regressions, an older PCI IRQ management
  regression, and an incorrect return value of a function in the APEI
  code.

  Specifics:

   - Fix three ACPICA issues related to the interpreter locking and
     introduced by recent changes in that area (Lv Zheng).

   - Fix a PCI IRQ management regression introduced during the 4.7 cycle
     and related to the configuration of shared IRQs on systems with an
     ISA bus (Sinan Kaya).

   - Fix up a return value of one function in the APEI code (Punit
     Agrawal)"

* tag 'acpi-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPICA: Dispatcher: Fix interpreter locking around acpi_ev_initialize_region()
  ACPICA: Dispatcher: Fix an unbalanced lock exit path in acpi_ds_auto_serialize_method()
  ACPICA: Dispatcher: Fix order issue of method termination
  ACPI / APEI: Fix incorrect return value of ghes_proc()
  ACPI/PCI: pci_link: Include PIRQ_PENALTY_PCI_USING for ISA IRQs
  ACPI/PCI: pci_link: penalize SCI correctly
  ACPI/PCI/IRQ: assign ISA IRQ directly during early boot stages

Pull power management fixes from Rafael Wysocki:
 "These fix two intel_pstate issues related to the way it works when the
  scaling_governor sysfs attribute is set to "performance" and fix up
  messages in the system suspend core code.

  Specifics:

   - Fix a missing KERN_CONT in a system suspend message by converting
     the affected code to using pr_info() and pr_cont() instead of the
     "raw" printk() (Jon Hunter).

   - Make intel_pstate set the CPU P-state from its .set_policy()
     callback when the scaling_governor sysfs attribute is set to
     "performance" so that it interacts with NOHZ_FULL more predictably
     which was the case before 4.7 (Rafael Wysocki).

   - Make intel_pstate always request the maximum allowed P-state when
     the scaling_governor sysfs attribute is set to "performance" to
     prevent it from effectively ingoring that setting is some
     situations (Rafael Wysocki)"

* tag 'pm-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpufreq: intel_pstate: Always set max P-state in performance mode
  PM / suspend: Fix missing KERN_CONT for suspend message
  cpufreq: intel_pstate: Set P-state upfront in performance mode

Pull ARC updates from Vineet Gupta:

 - support IDU intc for UP builds

 - support gz, lzma compressed uImage [Daniel Mentz]

 - adjust /proc/cpuinfo for non-continuous cpu ids [Noam Camus]

 - syscall for userspace cmpxchg assist for configs lacking hardware atomics

 - rework of boot log printing mainly for identifying older arc700 cores

 - retiring some old code, build toggles

* tag 'arc-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: module: print pretty section names
  ARC: module: elide loop to save reference to .eh_frame
  ARC: mm: retire ARC_DBG_TLB_MISS_COUNT...
  ARC: build: retire old toggles
  ARC: boot log: refactor cpu name/release printing
  ARC: boot log: remove awkward space comma from MMU line
  ARC: boot log: don't assume SWAPE instruction support
  ARC: boot log: refactor printing abt features not captured in BCRs
  ARCv2: boot log: print IOC exists as well as enabled status
  ARCv2: IOC: use @ioc_enable not @ioc_exist where intended
  ARC: syscall for userspace cmpxchg assist
  ARC: fix build warning in elf.h
  ARC: Adjust cpuinfo for non-continuous cpu ids
  ARC: [build] Support gz, lzma compressed uImage
  ARCv2: intc: untangle SMP, MCIP and IDU

* acpica-fixes:
  ACPICA: Dispatcher: Fix interpreter locking around acpi_ev_initialize_region()
  ACPICA: Dispatcher: Fix an unbalanced lock exit path in acpi_ds_auto_serialize_method()
  ACPICA: Dispatcher: Fix order issue of method termination

* acpi-pci-fixes:
  ACPI/PCI: pci_link: Include PIRQ_PENALTY_PCI_USING for ISA IRQs
  ACPI/PCI: pci_link: penalize SCI correctly
  ACPI/PCI/IRQ: assign ISA IRQ directly during early boot stages

* acpi-apei-fixes:
  ACPI / APEI: Fix incorrect return value of ghes_proc()

In the code path of acpi_ev_initialize_region(), there is namespace
modification code unlocked. This patch tunes the code to make sure
such modification are always locked.

Fixes: 74f51b80 (ACPICA: Namespace: Fix dynamic table loading issues)
Tested-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

There is a lock unbalanced exit path in acpi_ds_initialize_method(),
this patch corrects it.

Fixes: 441ad11d (ACPICA: Dispatcher: Fix a mutex issue for method auto serialization)
Tested-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

The last step of the method termination should be the end of the method
serialization. Otherwise, the steps happening after it will face the race
issues that cannot be protected by the method serialization mechanism.

This patch fixes this issue by moving the per-method-object deletion code
prior than the end of the method serialization. Otherwise, the possible
race issues may result in AE_ALREADY_EXISTS error in a parallel
environment.

Fixes: 74f51b80 (ACPICA: Namespace: Fix dynamic table loading issues)
Reported-and-tested-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Pull powerpc fixes from Michael Ellerman:
 "Fixes marked for stable:
   - Convert cmp to cmpd in idle enter sequence (Segher Boessenkool)
   - cxl: Fix leaking pid refs in some error paths (Vaibhav Jain)
   - Re-fix race condition between going idle and entering guest (Paul Mackerras)
   - Fix race condition in setting lock bit in idle/wakeup code (Paul Mackerras)
   - radix: Use tlbiel only if we ever ran on the current cpu (Aneesh Kumar K.V)
   - relocation, register save fixes for system reset interrupt (Nicholas Piggin)

  Fixes for code merged this cycle:
   - Fix CONFIG_ALIVEC typo in restore_tm_state() (Valentin Rothberg)
   - KVM: PPC: Book3S HV: Fix build error when SMP=n (Michael Ellerman)"

* tag 'powerpc-4.9-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/64s: relocation, register save fixes for system reset interrupt
  powerpc/mm/radix: Use tlbiel only if we ever ran on the current cpu
  powerpc/process: Fix CONFIG_ALIVEC typo in restore_tm_state()
  powerpc/64: Fix race condition in setting lock bit in idle/wakeup code
  powerpc/64: Re-fix race condition between going idle and entering guest
  cxl: Fix leaking pid refs in some error paths
  powerpc: Convert cmp to cmpd in idle enter sequence
  KVM: PPC: Book3S HV: Fix build error when SMP=n

* pm-cpufreq-fixes:
  cpufreq: intel_pstate: Always set max P-state in performance mode
  cpufreq: intel_pstate: Set P-state upfront in performance mode

* pm-sleep-fixes:
  PM / suspend: Fix missing KERN_CONT for suspend message

Pull perf fixes from Ingo Molnar:
 "Misc kernel fixes: a virtualization environment related fix, an uncore
  PMU driver removal handling fix, a PowerPC fix and new events for
  Knights Landing"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/intel: Honour the CPUID for number of fixed counters in hypervisors
  perf/powerpc: Don't call perf_event_disable() from atomic context
  perf/core: Protect PMU device removal with a 'pmu_bus_running' check, to fix CONFIG_DEBUG_TEST_DRIVER_REMOVE=y kernel panic
  perf/x86/intel/cstate: Add C-state residency events for Knights Landing

Pull libnvdimm fixes from Dan Williams:
 "A build fix, a NULL de-reference found by static analysis, a misuse of
  the percpu_ref_exit() (tagged for -stable), and notification of failed
  attempts to clear media errors.

  These patches have received a build success notification from the
  0day- kbuild-robot and appeared in next-20161028"

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  device-dax: fix percpu_ref_exit ordering
  nvdimm: make CONFIG_NVDIMM_DAX 'bool'
  pmem: report error on clear poison failure
  libnvdimm, namespace: potential NULL deref on allocation error

Pull arm64 fixes from Will Deacon:
 "Three arm64 fixes for -rc3.  They're all pretty straightforward: a
  couple of NUMA issues from the Huawei folks and a thinko in
  __page_to_voff that seems to be benign, but is certainly better off
  fixed.

  Summary:
   - couple of NUMA fixes
   - thinko in __page_to_voff"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: mm: fix __page_to_voff definition
  arm64/numa: fix incorrect log for memory-less node
  arm64/numa: fix pcpu_cpu_distance() to get correct CPU proximity

Pull x86 fixes from Ingo Molnar:
 "Misc fixes: three build fixes, an unwinder fix and a microcode loader
  fix"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/microcode/AMD: Fix more fallout from CONFIG_RANDOMIZE_MEMORY=y
  x86: Fix export for mcount and __fentry__
  x86/quirks: Hide maybe-uninitialized warning
  x86/build: Fix build with older GCC versions
  x86/unwind: Fix empty stack dereference in guess unwinder

Pull timer fixes from Ingo Molnar:
 "Fix four timer locking races: two were noticed by Linus while
  reviewing the code while chasing for a corruption bug, and two
  from fixing spurious USB timeouts"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  timers: Prevent base clock corruption when forwarding
  timers: Prevent base clock rewind when forwarding clock
  timers: Lock base for same bucket optimization
  timers: Plug locking race vs. timer migration

Merge branches 'core-urgent-for-linus', 'irq-urgent-for-linus' and 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Pull objtool, irq and scheduler fixes from Ingo Molnar:
 "One more objtool fixlet for GCC6 code generation patterns, an irq
  DocBook fix and an unused variable warning fix in the scheduler"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  objtool: Fix rare switch jump table pattern detection

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  doc: Add missing parameter for msi_setup

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/fair: Remove unused but set variable 'rq'

Now that we have referece to section name string table in
apply_relocate_add(), use it to

 - print the name of section being relocated
 - print symbol with NULL name (since it refers to a section)

before

| Section to fixup 7000a060
| =========================================================
| rela->r_off | rela->addend | sym->st_value | ADDR | VALUE
| =========================================================
|	1c		0		7000e000  7000a07c 7000e000 []
|	40		0		7000a000  7000a0a0 7000a000 []

after

| Section to fixup .eh_frame @7000a060
| =========================================================
| r_off	r_add	st_value ADDRESS  VALUE
| =========================================================
|    1c	0	7000e000 7000a07c 7000e000 [.init.text]
|    40	0	7000a000 7000a0a0 7000a000 [.exit.text]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>