Add documentation for device tree binding of NVIDIA's Tegra I2C
controller driver.

Describing all compatible values used for different Tegra SoCs
in details in this documentation.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: fixed a couple typos, trimmed examples]
Signed-off-by: Stephen Warren <swarren@nvidia.com>

NVIDIA's Tegra114 has 6 SPI controllers. These controllers are
redesign on T114 with different register interface.

Add DT entry for spi controllers and make it compatible with
"nvidia,tegra114-spi", since they are a new incompatible design.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: fixed reg property for 3rd SPI controller]
Signed-off-by: Stephen Warren <swarren@nvidia.com>

NVIDIA's Tegra114 SoCs have the matrix keyboard controller which
supports 11x8 type of matrix. The number of rows and columns
are configurable.

Add DT entry for KBC controller with compatibility as "nvidia,tegra114-kbc".
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Add APB DMA requestor and serial aliases for serial controller.
There are two serial drivers i.e. 8250 based simple serial driver
and APB DMA based serial driver for higher baudrate and performace.

The simple serial driver is selected by compatible value
"nvidia,tegra114-uart", "nvidia,tegra20-uart", and the APB DMA based
driver is selected by compatible value "nvidia,tegra114-hsuart",
"nvidia,tegra30-hsuart".
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

NVIDIA's Tegra114 has 5 I2C controllers. These controllers have the
following changes which makes incompatible with previous hardware:
- Single clock source to I2C controller.
- Interrupt support for per packet transfer.

Add DT entry for I2C controllers and make it compatible with
"nvidia,tegra114-i2c".
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: fixed location of status property for consistency]
Signed-off-by: Stephen Warren <swarren@nvidia.com>

NVIDIA's Tegra114 has 32 channels APB DMA controller. Add DT entry for
APB DMA controllers and make it compatible with "nvidia,tegra114-apbdma".

Tegra114 DMA controller is not compatible with Tegra30/Tegra20 DMA
controller driver as in Tegra114, the global pause also clock gate the
DMA register and hence it iw not possible to write the DMA register
with global pause.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: fixed DT node order]
Signed-off-by: Stephen Warren <swarren@nvidia.com>

This patch adds a device tree node for the four PWM controllers present
on Tegra114.
Signed-off-by: Andrew Chew <achew@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

We should be defining the PWM nodes with status as "disabled" in the
chip-specific dtsi file, since we don't know whether specific boards
will use the PWM or not. This patch fixes the PWM node status for
Tegra20 and Tegra30.

Also fixed the one user of PWM, which is the Tegra20 medcom-wide board,
so that PWM is set to "okay" in the board-specific dts file.
Signed-off-by: Andrew Chew <achew@nvidia.com>
[swarren: in medcom-wide: fixed node sort order, removed duplicate pwm:
label, fixed syntax error]
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Dalmore has a built-in eMMC device and a user-accessible SD card slot.
Add device tree nodes to enable these.

Based on changes by: Pritesh Raithatha <praithatha@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
[swarren: added commit description, fixed DT node sort order]
Signed-off-by: Stephen Warren <swarren@nvidia.com>

This patch adds in the SDHCI nodes for the busses supported on Tegra114
boards.
Signed-off-by: Pritesh Raithatha <praithatha@nvidia.com>
[Rhyland added clk refs to & reordered sdhci nodes and removed spaces]
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
[swarren: fixed DT node sort order]
Signed-off-by: Stephen Warren <swarren@nvidia.com>

This change adds the default pinctrl nodes for the Dalmore Tegra114
platform.
Signed-off-by: Pritesh Raithatha <praithatha@nvidia.com>
[Rhyland added patch description]
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
[swarren: fixed DT node sort order]
Signed-off-by: Stephen Warren <swarren@nvidia.com>

The USB PHY nodes are all grouped together rather than being sorted based
on reg address like all other nodes fix this.

I apologize for the churn; I should have noticed this during review of the
patches that caused this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Remove white-space from empty line; triggers checkpatch.
Signed-off-by: Stephen Warren <swarren@nvidia.com>

A gap exists in the binding's clock ID definitions. Fix the clock driver
to be consistent. This allows pclk to be looked up through device tree
and prevents:

ERROR: could not get clock /pmc:pclk(0)
Signed-off-by: Stephen Warren <swarren@nvidia.com>

The UART driver enables the console uart clock, so we don't need to do that
anymore in this file.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Add references to tegra_car clocks for the basic device nodes. Also remove
the clock-frequency property of the serial node as the UART driver can now
use the clock framework to obtain the frequency.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Implement clocks for Tegra114.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

The device tree binding models Tegra114 CAR (Clock And Reset) as a single
monolithic clock provider.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Workaround a hardware bug in MSENC during clock enable.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

We will need some tegra peripheral clocks with the CLK_IGNORE_UNUSED flag,
most notably mselect, which is a bridge between AXI and most peripherals.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Tegra114 introduces new PLL types. This requires new clocktypes as well
as some new fields in the pll structure.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

PLLC2 and PLLC3 on Tegra114 have separate phaselock and frequencylock bits.
So switch to a lock mask to be able to test both at the same time.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Some PLLs in Tegra114 don't use a power of 2 mapping for the post divider.
Introduce a table based approach and switch PLLU to it.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Tegra114 PLLC2 and PLLC3 don't have a lock enable bit. The lock bits are
always functional.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Not all PLLs in Tegra114 have a bypass bit. Adapt the common code to only use
this bit when available.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Refactor the PLL programming code to make it useable by the new PLL types
introduced by Tegra114.

The following changes were done:

* Split programming the PLL into updating m,n,p and updating cpcon
* Move locking from _update_pll_cpcon() to clk_pll_set_rate()
* Introduce _get_pll_mnp() helper
* Move check for identical m,n,p values to clk_pll_set_rate()
* struct tegra_clk_pll_freq_table will always contain the values as defined
  by the hardware.
* Simplify the arguments to clk_pll_wait_for_lock()
* Split _tegra_clk_register_pll()
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

tegra_boot_secondary() relies on some of the car ops. This means having an
uninitialized tegra_cpu_car_ops will lead to an early boot panic.
Providing a dummy struct avoids this and makes adding Tegra114 clock support
in a bisectable way a lot easier.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

The Tegra clock driver is initialized during the ARM machine descriptor's
.init_irq() hook. It can't be initialized earlier, since dynamic memory
usage is required. It can't be initialized later, since the .init_timer()
hook needs the clocks initialized. However, at this time, udelay()
doesn't work.

The Tegra clock initialization table may enable some PLLs. Enabling a PLL
may require usage of udelay(). Hence, this can't happen right when the
clock driver is initialized.

To solve this, separate the clock driver initialization from the clock
table processing, so they can execute at separate times.
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Correct IDs for cdev1 and cdev2 are 94 and 93 respectively.
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
[swarren: split into separate driver and device-tree patches]
Signed-off-by: Stephen Warren <swarren@nvidia.com>

By default these clocks are children of pll_m, but in downstream kernels
they are reparented to pll_c. While at it, decrease their frequencies to
300 MHz because the defaults aren't in the specified range.

gr2d can reportedly run at much higher frequencies, but 300 MHz works
and is a more conservative default.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

The tegra_periph_reset_assert() and tegra_periph_reset_deassert()
functions can be used by drivers to reset peripherals. In order to allow
such drivers to be built as modules, export the functions.

Note that this restores the status quo as the functions were exported
before the move to the drivers/clk tree.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

The parameter name should be "gate", not "periph".  This worked, however,
because it happens that everywhere periph_clk_to_bit is called, "gate" was
in the local scope.
Signed-off-by: Yen Lin <yelin@nvidia.com>
Signed-off-by: Andrew Chew <achew@nvidia.com>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: Prashant Gaikwad <pgaikwad@nvidia.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

After the patch series for system suspending support, tegra_idle_lp2_last()
no longer uses its parameters cpu_on_time or cpu_off_time, so remove them.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Adding suspend to RAM support for Tegra platform. There are three suspend
mode for Tegra. The difference were below.

* LP2: CPU voltage off
* LP1: CPU voltage off, DRAM in self-refresh
* LP0: CPU + Core voltage off, DRAM in self-refresh

After this patch, the LP2 suspend mode will be supported.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

The PMC mostly controls the entry and exit of the system from different
sleep modes. Different platform or system may have different configurations.
The power management configurations of PMC is represented as some properties.
The system needs to define the properties when the system supports deep sleep
mode (i.e. suspend).

Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Add the wake up handling for legacy irq controller, and using
IRQCHIP_MASK_ON_SUSPEND for wake irq handling.

Based on the work by:
Varun Wadekar <vwadekar@nvidia.com>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

This patch add the gpio wakeup source handling for the Tegra platform. It
was be done by enabling the irq for the gpio in the gpio controller and
enabling the bank irq of the gpio in the Tegra legacy irq controller when
the system going to suspend.

Based on the work by:
Varun Wadekar <vwadekar@nvidia.com>

Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>