- 27 Jul, 2010 40 commits
-
-
Jing Huang authored
Clear PSS memory reset that is set as part of power-on-reset (pci reset). Complete PMM memory reset before BISTR start. Clear EDRAM BISTR start bit after fixed delay. BISTR DONE bit status is not getting set. Use a fixed 1ms delay for BISTR now. Expose PMM IT memory definitions to host. Signed-off-by:
Jing Huang <huangj@brocade.com> Signed-off-by:
James Bottomley <James.Bottomley@suse.de>
-
Jing Huang authored
Update related data structures to support firmeare configuration. Add AEN events related to firmware configuation. Signed-off-by:
-
Jing Huang authored
Add PBC port disable handling in BFA and return the appropriate status from BFA APIs. In bfa_fcs_lport.c, handle OFFLINE event to avoid BFA_ASSERT. Signed-off-by:
-
Jing Huang authored
Add a max retry limit for PRLI retries. Max retry limit (5) is same as used in rport PLOGI. Once the retries are exhausted, invoke rport offline so that existing logic of rport re-discovery can kick-in. Also fixed a bug in rport.c where one less retry was happening. Signed-off-by:
-
Jing Huang authored
When a rport goes offline, its speed setting was not reset. Subsequently, if the rport was not deleted due to it coming back online within rport del timeout, previously discovered speed would continue to show up. The fix is to reset the speed when processing rport offline transition. In rport attributes, rport's with unknown speed were indicated as TRL enforced. The right thing do to would be to use TRL default speed to determine if TRL is enforced, when TRL is enabled. Signed-off-by:
-
Jing Huang authored
Do not update the coalesce flag of the intr_attr struct in driver config area on config response. This is to prevent the coalesce flag being reported as on after an ioc disable/enable even if it was set to off before disable. Signed-off-by:
-
Jing Huang authored
Use standards defined 2 * RA_TOV as a timeout for ELS Request retries. And standards defined 3 * RA_TOV as a timeout for FC-CT Request retries. Also, added a check to send RPSC2 to a Brocade Fabric only. Signed-off-by:
-
Jing Huang authored
- Added time stamp for fcport stats reset - Added new fileds to the statistics data structures. - Typo removal and minor cleanup. Signed-off-by:
-
Jing Huang authored
This patch fixes the APIs to obtain ioc attributes - fix API to obtain wwpn, wwnn, and mac. - add API to get mfg wwpn, wwnn, and mac. - fix API to obtain wwn of boot target. Signed-off-by:
-
Jing Huang authored
Vport state machine does not cleanup associated lport in some states: while waiting for fdisc response or fdisc failure state. The fixe is to cleanup lport on vport delete in all states. In fdisc state, discard fdisc response and delete lport and wait for lport deletecompletion. in error state, delete lport and wait for delete completion. Signed-off-by:
-
Jing Huang authored
This patch enables creating PBC vport. During fcs init, fcs will read PBC vport using bfa iocfc API and invoke fcb callback to add the pbc vport entries into a list. The pbc vport list will be traversed in the subsequent pci probe process and vport will be created using fc transport provided vport create function. Signed-off-by:
-
Jing Huang authored
The patch includes the driver side changes to enable basic PBC (PreBoot Configuration) feature. - Data structure changes and new definitions for PBC. - APIs to access PBC info. - Remove unused code. Signed-off-by:
-
Jing Huang authored
This patch enables support of new mezzanine cards for HP and IBM blade server. - Add new pciids for HP and IBM mezzanine card. - Add a new firmware image for HP mezzanine card, which is running in FC only mode. Rename firmware image to reflect the difference. Change the firmware download code accordingly for the above changes. Signed-off-by:
-
Eric Moore authored
fixes surrounding PCIe enhanced error handling: (1) We need to reject all request generated internaly inside the driver as well as request arriving from the scsi mid layer when PCIe EEH is active. The fix is to add a per adapter flag called pci_error_recovery which is checked thru out the driver when request are generated. (2) We don't need to call the pci_driver->remove directly from the PCIe callbacks becuase its already called from the PCIe EEH code. In its place we are shutting down the watchdog timer, and flushing back all pending IO. (3) We need to save and restore the pci state across PCIe EEH handling. Signed-off-by:
Eric Moore <eric.moore@lsi.com> Signed-off-by:
-
Eddie Wai authored
Signed-off-by:
Eddie Wai <eddie.wai@broadcom.com> Signed-off-by:
-
Michael Chan authored
This sysfs attribute is proven to be useful during pivot_root. Signed-off-by:
Michael Chan <mchan@broadcom.com> Signed-off-by:
Benjamin Li <benli@broadcom.com> Acked-by:
Anil Veerabhadrappa <anilgv@broadcom.com> Reviewed-by:
Mike Christie <michaelc@cs.wisc.edu> Signed-off-by:
-
Eddie Wai authored
In compliance to RFC793, a TCP graceful termination will be used instead of an abortive termination for the case where the remote has initiated the close of the connection. Additionally, a TCP abortive termination will be used to close the connection when a logout response is not received in time after a logout request has been initiated. Signed-off-by:
-
Eddie Wai authored
Added variables to separate the fine tuned timeout values for connection destroy and context destroy for both 1g and 10g devices. v2: Extended the 5771X disconnect timeout from 10s to 20s as the firmware has a retransmission timeout of 16s. This fixes one of the iscsi_endpoint leak issues when the target is slow or non-responsive to our TCP FIN. Signed-off-by:
-
Eddie Wai authored
For cases where the iSCSI disconnection procedure times out due to the iSCSI daemon being slow or unresponsive, the bnx2i_stop routine will now perform hardware cleanup via bnx2i_hw_ep_disconnect on all active endpoints so that subsequent operations will perform properly. Also moved the mutex locks inside ep_connect and ep_disconnect so that proper exclusivity can resolve simultaneous calls to the ep_disconnect routine. v2: Removed the unnecessary read lock in the bnx2i_stop Signed-off-by:
-
Eddie Wai authored
This introduces a new active linklist which would link up all active bnx2i_endpoints. This will be used by subsequent patches that follows. Signed-off-by:
-
Eddie Wai authored
This patch introduces a new bnx2i_hw_ep_disconnect routine which contains all chip related disconnect and clean up procedure of iSCSI offload connections. This separation is intended as a preparation for the subsequent bnx2i_stop patch. Signed-off-by:
-
FUJITA Tomonori authored
map_region and unmap_region could access to invalid memory area since they don't check the size boundary. Signed-off-by:
FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Acked-by:
Douglas Gilbert <dgilbert@interlog.com> Signed-off-by:
-
Wayne Boyer authored
The value used to change the endian representation on the new adapters has changed. This patch updates that value. Signed-off-by:
Wayne Boyer <wayneb@linux.vnet.ibm.com> Signed-off-by:
-
Wayne Boyer authored
This patch allows the driver to recognize a new Obsidian-E based adapter that uses a new subsystem ID. This patch also fixes a few tab/space problems. Signed-off-by:
-
Jiri Slaby authored
Stanse found that in mvs_abort_task, mvi_dev is dereferenced earlier than tested for being NULL. Move the assignment below the test. Signed-off-by:
Jiri Slaby <jslaby@suse.cz> Signed-off-by:
-
Kei Tokunaga authored
Printing Doorbell register in a case of hard reset and timeout should be useful for figuring out the state of the system. Signed-off-by:
Kei Tokunaga <tokunaga.keiich@jp.fujitsu.com> Acked-by:
"Desai, Kashyap" <Kashyap.Desai@lsi.com> Signed-off-by:
-
Justin P. Mattock authored
The below patch fixes a warning message generated by gcc 4.6.0 CC drivers/scsi/hosts.o drivers/scsi/hosts.c: In function 'scsi_host_alloc': drivers/scsi/hosts.c:328:6: warning: variable 'rval' set but not used Fix this by removing the rval but placing a printk warning where it would have been set. Signed-off-by:
Justin P. Mattock <justinmattock@gmail.com> Signed-off-by:
-
Mike Christie authored
If the user accidentally changes LUN mappings or it occurs due to a bug, then it can cause data corruption that can take months and months to track down. This patch adds a log message when getting REPORT_LUNS_DATA_CHANGED and it adds a generic message for other Unit Attentions with asc == 0x3f. We are working on adding support for handling of these errors, but I think until then we should at least log a message so tracking down problems as a result of one of these changes is a little easier. Signed-off-by:
-
Kei Tokunaga authored
This patch fixes mptsas disk hot-removal processing. The hot-removal processing doesn't complete because of this condition. drivers/message/fusion/mptsas.c: mptsas_taskmgmt_complete() if ((mptsas_find_vtarget(ioc, channel, id)) && !ioc->fw_events_off) mptsas_queue_device_delete(...); mptsas_queue_device_delete(), which must be called for hot-removal, never gets called because mptsas_find_vtarget() always returns 0 here. At that time, the vtarget has already been freed in mptsas_target_destroy(), and also the scsi_device has been marked as SDEV_DEL. As a result of the issue, port deletion functions won't get called and the device ends up being in an incomplete state. (Some data structures and sysfs entries, which should be removed in hot-removal, remain.) One side effect of this is that a hot-addition of the device (bringing the device back on) fails. This patch just removes mptsas_find_vtarget() from the if-state condition. Signed-off-by: -
Wayne Boyer authored
The 64 bit chip used in new adapters does not properly support the BIST register in PCI config space. This patch implements an alternative MMIO write reset method. Signed-off-by:
-
Nick Cheng authored
1. To support Type C RAID controller, ACB_ADAPTER_TYPE_C, i.e. PCI device ID: 0x1880. Signed-off-by: Nick Cheng< nick.cheng@areca.com.tw > Signed-off-by: -
James Bottomley authored
we also need to clean up and free the cdev. Reported-by:
Jani Nikula <ext-jani.1.nikula@nokia.com> Cc: Stable Tree <stable@kernel.org> Signed-off-by:
-
Brian King authored
Bump driver version Signed-off-by:
Brian King <brking@linux.vnet.ibm.com> Signed-off-by:
-
Brian King authored
If we encounter an error when sending a management datagram (i.e. non SCSI command, such as virtual adapter initialization command), we end up incrementing the request_limit, even though we don't decrement it for these commands. Fix this up by doing this increment in the error path for SRP commands only. Signed-off-by:
-
Brian King authored
Fixes a deadlock that can occur if we hit a command timeout during the virtual adapter initialization. The event done functions are written with the assumption that no locks are held, however, when purging requests this is not true. Fix up the purge function to drop the lock so that the done function is not called with the lock held, which can cause a deadlock. Signed-off-by:
-
Brian King authored
This fixes a softlockup seen on resume. During resume, the CRQ must be reenabled. However, the H_ENABLE_CRQ hcall used to do this may return H_BUSY or H_LONG_BUSY. When this happens, the caller is expected to retry later. This patch changes a simple loop, which was causing the softlockup, to a loop at task level which sleeps between retries rather than simply spinning. Signed-off-by:
-
Brian King authored
Bump driver version. Signed-off-by:
-
Brian King authored
Adds support for fc_block_scsi_eh to block the EH handlers if the target device is in the blocked state to ensure we don't take devices offline. Signed-off-by:
-
Brian King authored
This fixes a softlockup seen on resume. During resume, the CRQ must be reenabled. However, the H_ENABLE_CRQ hcall used to do this may return H_BUSY or H_LONG_BUSY. When this happens, the caller is expected to retry later. Normally the H_ENABLE_CRQ succeeds relatively soon. However, we have seen cases where this can take long enough to see softlockup warnings. This patch changes a simple loop, which was causing the softlockup, to a loop at task level which sleeps between retries rather than simply spinning. Signed-off-by:
-
Bandan Das authored
In mpt_detach, call to pci_set_drvdata is redundant because it has already been called in mpt_adapter_disable. In mpt_attach, ioc->pcidev is set to pdev two times. Signed-off-by:
Bandan Das <bandan.das@stratus.com> Acked-by:
-
