- 08 Dec, 2015 2 commits
-
-
Jens Kuske authored
The Orange Pi Plus is a SBC based on the Allwinner H3 SoC with 8GB eMMC, multiple USB ports through a USB hub chip, SATA through a USB-SATA bridge, one uSD slot, a 10/100/1000M ethernet port, WiFi, HDMI, headphone jack, IR receiver, a microphone, a CSI connector and a 40-pin GPIO header. Signed-off-by: Jens Kuske <jenskuske@gmail.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
-
Jens Kuske authored
The Allwinner H3 is a home entertainment system oriented SoC with four Cortex-A7 cores and a Mali-400MP2 GPU. Signed-off-by: Jens Kuske <jenskuske@gmail.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
-
- 07 Dec, 2015 2 commits
-
-
Chen-Yu Tsai authored
The DRAM gates controls direct memory access for some peripherals. These peripherals include the display pipeline, so add the required gates to the simplefb nodes as well. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
-
Chen-Yu Tsai authored
The DRAM gates controls direct memory access for some peripherals. These peripherals include the display pipeline, so add the required gates to the simplefb nodes as well. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
-
- 03 Dec, 2015 1 commit
-
-
Chen-Yu Tsai authored
The Allwinner A80 SoC has an NMI controller. NMI is an external interrupt pin exclusely used with PMICs and other system critical peripherals (such as RTC) in Allwinner's reference designs. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
-
- 01 Dec, 2015 8 commits
-
-
Chen-Yu Tsai authored
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
-
Chen-Yu Tsai authored
This patch adds a device node for the Reduced Serial Bus (RSB) controller and the defacto pinmux setting to the A80 dtsi. Since there is only one possible pinmux setting for RSB, just set it in the dtsi. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
-
Chen-Yu Tsai authored
The A80 Optimus board has a consumer IR receiver. Enable it in the DT. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
-
Chen-Yu Tsai authored
The Allwinner A80 SoC has a consumer IR receiver, which is the same as older SoCs. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
-
Chen-Yu Tsai authored
LED3 is connected to pin PM15 on R_PIO. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
-
Chen-Yu Tsai authored
The A80 has a secondary pin controller. Add a device node for it. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
-
Chen-Yu Tsai authored
The main (24MHz) clock on the A80 is configurable via the PRCM address space. The low power/speed (32kHz) clock is from an external chip, the AC100. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
-
Chen-Yu Tsai authored
This adds the supported PRCM clocks and reset controls to the A80 dtsi. The DAUDIO module clocks are not supported yet. Also update clock and reset phandles for r_uart. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
-
- 24 Nov, 2015 2 commits
-
-
Hans de Goede authored
Add a node describing the touchscreen found on the pov protab2-ips9 tablet. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
-
Hans de Goede authored
Add a node describing the touchscreen controller used on the iNet1 tablet. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
-
- 23 Nov, 2015 2 commits
-
-
Stefan Monnier authored
Enable the on-chip audio codec Signed-off-by: Stefan Monnier <monnier@iro.umontreal.ca> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
-
Stefan Monnier authored
Enable the on-chip audio codec Signed-off-by: Stefan Monnier <monnier@iro.umontreal.ca> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
-
- 20 Nov, 2015 6 commits
-
-
Michael van Slingerland authored
Add a node describing the AXP152 pmic used on Auxtek T004 boards. Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Michael van Slingerland <michael@deviousops.nl> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
-
Hans de Goede authored
Add a node describing the lcd panel backlight on the pov protab2 ips9 tablet. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
-
Hans de Goede authored
Add a node describing the lcd panel backlight on the UTOO P66 tablet. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
-
Hans de Goede authored
Add a node describing the lcd panel backlight on the iNet1 tablet. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
-
Hans de Goede authored
The iNet1 tablet uses the A10's integrated audio codec, enable it. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
-
Chen-Yu Tsai authored
Some boards, such as tablets, have regulators providing power to parts of the display pipeline, like signal converters and LCD panels. Add labels to the simplefb device nodes so that we can reference them in the board dts files to add regulator supply properties. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
-
- 17 Nov, 2015 10 commits
-
-
Priit Laes authored
Gemei G9 has internal speakers and headphone jack. Audio switching from internal speakers to headphones is automatically handled by extra FT2012Q audio amplifier chip that works out of the box. Signed-off-by: Priit Laes <plaes@plaes.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
-
Priit Laes authored
ADC seems to be using ldo2 for reference voltage. Signed-off-by: Priit Laes <plaes@plaes.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
-
Priit Laes authored
Add regulator nodes for axp209 using the axp209.dtsi include. Signed-off-by: Priit Laes <plaes@plaes.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
-
Hans de Goede authored
The inet9f-rev03 tablet has multiple fire-buttons / direction controls, add support for these using the same axis mapping as ps2 compatible game controllers with the same stick / button layout use. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
-
Jelle van der Waa authored
Enable the on-chip audio codec Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
-
Aleksei Mamlin authored
Enable on-chip audio codec on the Wexler TAB7200 tablet. Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
-
Marcus Weseloh authored
Enable the on-chip audio codec on the Olimex A20-SOM-EVB Signed-off-by: Marcus Weseloh <mweseloh42@gmail.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
-
Lawrence Yu authored
Enable the axp221 PMIC chip in the dts file. Allows board to power off correctly from the poweroff command This board requires dc1sw to be enabled in order to provide a power source for the 5V DCDC converter that powers USB2. This board uses dldo1 for 3.3V wifi power This board requires dldo3 to be enabled at 2.8V in order to provide voltage to the pullup resistors for the i2c0 bus. Signed-off-by: Lawrence Yu <lyu@micile.com> Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
-
Stefan Roese authored
This baseboard from SWAC is equipped with the ICnova-A20 SoM from Incircuit. This board is equipped with the following interfaces / devices: - 512 MiB SDRAM - 4 GiB MLC NAND (Micron MT29F32G08CBACAWP or Hynix H27UBG8T2BTR) - USB host - LCD 800x480 - HDMI - CAN Note that the NAND support is still missing. As its currently not supported in mainline for sunxi and especially for these MLC devices. The original plan was to also provide a dtsi for the ICnova SoM, to put all the SoM internal nodes / properties there. But as I don't have a clear overview of the SoM specific and baseboard specific differences, I'm putting all in one dts for now. Once somebody pushed support for some other baseboard using the A20 SoM from Incircuit (e.g. the ADB4006 reference design), this should be separated. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Marcus Heuer <marcus.heuer@swac.de> [maxime: Fixed CPU regulator upper voltage boundary] Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
-
Adam Sampson authored
The pcDuino V3 Nano has a 3.5mm TRRS jack socket for audio, using the CTIA standard pinout, connected to HPOUTL, HPOUTR, HPCOM/HPCOMFB and MICIN1/VMIC (via appropriate RC networks) on the A20. The PH00 GPIO is wired for headphone plug detection: it reads 0 when nothing's plugged in, and 1 when a plug is inserted. LINEINL/R and FMINL/R are not connected. Signed-off-by: Adam Sampson <ats@offog.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
-
- 16 Nov, 2015 1 commit
-
-
Linus Torvalds authored
-
- 15 Nov, 2015 6 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull perf updates from Thomas Gleixner: "Mostly updates to the perf tool plus two fixes to the kernel core code: - Handle tracepoint filters correctly for inherited events (Peter Zijlstra) - Prevent a deadlock in perf_lock_task_context (Paul McKenney) - Add missing newlines to some pr_err() calls (Arnaldo Carvalho de Melo) - Print full source file paths when using 'perf annotate --print-line --full-paths' (Michael Petlan) - Fix 'perf probe -d' when just one out of uprobes and kprobes is enabled (Wang Nan) - Add compiler.h to list.h to fix 'make perf-tar-src-pkg' generated tarballs, i.e. out of tree building (Arnaldo Carvalho de Melo) - Add the llvm-src-base.c and llvm-src-kbuild.c files, generated by the 'perf test' LLVM entries, when running it in-tree, to .gitignore (Yunlong Song) - libbpf error reporting improvements, using a strerror interface to more precisely tell the user about problems with the provided scriptlet, be it in C or as a ready made object file (Wang Nan) - Do not be case sensitive when searching for matching 'perf test' entries (Arnaldo Carvalho de Melo) - Inform the user about objdump failures in 'perf annotate' (Andi Kleen) - Improve the LLVM 'perf test' entry, introduce a new ones for BPF and kbuild tests to check the environment used by clang to compile .c scriptlets (Wang Nan)" * 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (32 commits) perf/x86/intel/rapl: Remove the unused RAPL_EVENT_DESC() macro tools include: Add compiler.h to list.h perf probe: Verify parameters in two functions perf session: Add missing newlines to some pr_err() calls perf annotate: Support full source file paths for srcline fix perf test: Add llvm-src-base.c and llvm-src-kbuild.c to .gitignore perf: Fix inherited events vs. tracepoint filters perf: Disable IRQs across RCU RS CS that acquires scheduler lock perf test: Do not be case sensitive when searching for matching tests perf test: Add 'perf test BPF' perf test: Enhance the LLVM tests: add kbuild test perf test: Enhance the LLVM test: update basic BPF test program perf bpf: Improve BPF related error messages perf tools: Make fetch_kernel_version() publicly available bpf tools: Add new API bpf_object__get_kversion() bpf tools: Improve libbpf error reporting perf probe: Cleanup find_perf_probe_point_from_map to reduce redundancy perf annotate: Inform the user about objdump failures in --stdio perf stat: Make stat options global perf sched latency: Fix thread pid reuse issue ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull scheduler fix from Thomas Gleixner: "A single fix to prevent math underflow in the numa balancing code" * 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: sched/numa: Fix math underflow in task_tick_numa()
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull liblockdep fixes from Thomas Gleixner: "Three small patches to synchronize liblockdep with the latest core changes" * 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: tools/liblockdep: explicitly declare lockdep API we call from liblockdep tools/liblockdep: add userspace versions of WRITE_ONCE and RCU_INIT_POINTER tools/liblockdep: remove task argument from debug_check_no_locks_held
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 fixes from Thomas Gleixner: "A couple of fixes and updates related to x86: - Fix the W+X check regression on XEN - The real fix for the low identity map trainwreck - Probe legacy PIC early instead of unconditionally allocating legacy irqs - Add cpu verification to long mode entry - Adjust the cache topology to AMD Fam17H systems - Let Merrifield use the TSC across S3" * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/cpu: Call verify_cpu() after having entered long mode too x86/setup: Fix low identity map for >= 2GB kernel range x86/mm: Skip the hypervisor range when walking PGD x86/AMD: Fix last level cache topology for AMD Fam17h systems x86/irq: Probe for PIC presence before allocating descs for legacy IRQs x86/cpu/intel: Enable X86_FEATURE_NONSTOP_TSC_S3 for Merrifield
-
Linus Torvalds authored
Merge branches 'irq-urgent-for-linus' and 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull irq and timer fixes from Thomas Gleixner: - An irq regression fix to restore the wakeup behaviour of chained interrupts. - A timer fix for a long standing race versus timers scheduled on a target cpu which got exposed by recent changes in the workqueue implementation. * 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: genirq/PM: Restore system wake up from chained interrupts * 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: timers: Use proper base migration in add_timer_on()
-
git://git.linux-mips.org/pub/scm/ralf/upstream-linusLinus Torvalds authored
Pull MIPS updates from Ralf Baechle: "These are the highlists of the main MIPS pull request for 4.4: - Add latencytop support - Support appended DTBs - VDSO support and initially use it for gettimeofday. - Drop the .MIPS.abiflags and ELF NOTE sections from vmlinux - Support for the 5KE, an internal test core. - Switch all MIPS platfroms to libata drivers. - Improved support, cleanups for ralink and Lantiq platforms. - Support for the new xilfpga platform. - A number of DTB improvments for BMIPS. - Improved support for CM and CPS. - Minor JZ4740 and BCM47xx enhancements" * 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (120 commits) MIPS: idle: add case for CPU_5KE MIPS: Octeon: Support APPENDED_DTB MIPS: vmlinux: create a section for appended DTB MIPS: Clean up compat_siginfo_t MIPS: Fix PAGE_MASK definition MIPS: BMIPS: Enable GZIP ramdisk and timed printks MIPS: Add xilfpga defconfig MIPS: xilfpga: Add mipsfpga platform code MIPS: xilfpga: Add xilfpga device tree files. dt-bindings: MIPS: Document xilfpga bindings and boot style MIPS: Make MIPS_CMDLINE_DTB default MIPS: Make the kernel arguments from dtb available MIPS: Use USE_OF as the guard for appended dtb MIPS: BCM63XX: Use pr_* instead of printk MIPS: Loongson: Cleanup CONFIG_LOONGSON_SUSPEND. MIPS: lantiq: Disable xbar fpi burst mode MIPS: lantiq: Force the crossbar to big endian MIPS: lantiq: Initialize the USB core on boot MIPS: lantiq: Return correct value for fpi clock on ar9 MIPS: ralink: Add missing clock on rt305x ...
-