Since PWMs are only useful if they are actually connected to an output pin,
let users enable them explicitly in their device trees where they should
also set up the pin configuration.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

All PWM users should explicitly enable the used PWMs in their device tree
so they can be disabled by default in imx6qdl.dtsi.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

All PWM users should explicitly enable the used PWMs in their device tree
so they can be disabled by default in imx6qdl.dtsi.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The PU regulator is enabled during boot, but not necessarily always-on.
It can be disabled by the generic pm domain framework when the PU power
domain is shut down. The ramp delay of 150 us might be a bit conservative,
the value is taken from the Freescale kernel.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The PGC that is part of GPC controls isolation and power sequencing of the
power domains. The PU power domain will be handled by the generic pm domain
framework. It needs a phandle to the PU regulator to turn off power when
the domain is disabled and a list of clocks to be enabled during powerup
for reset propagation.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The PGC that is part of GPC controls isolation and power sequencing of the
power domains. The PU power domain will be handled by the generic pm domain
framework. It needs a phandle to the PU regulator to turn off power when
the domain is disabled, and a list of phandles to all clocks that must be
enabled during powerup for reset propagation.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The chipidea driver adds an extra line of spam to the log when a
host-only chipidea instance is left set to the default of a dual role
controller.

[    2.010873] ci_hdrc ci_hdrc.1: doesn't support gadget

Set the dr_mode property to host on all the host-only nodes
to avoid this warning.
Signed-off-by: Matt Porter <mporter@konsulko.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The WaRP Board is a Wearable Reference Plaform. The board features:

 - Freescale i.MX6 SoloLite processor with 512MB of RAM
 - Freescale FXOS8700CQ 6-axis Xtrinsic sensor
 - Freescale Kinetis KL16 MCU
 - Freescale Xtrinsic MMA955xL intelligent motion sensing platform

The board implements a hybrid architecture to address the evolving
needs of the wearables market. The platform consists of a main board
and an example daughtercard with the ability to add additional
daughtercards for different usage models.

For more information about the project, visit:

 http://www.warpboard.org/Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The anyway depricated gpio-range-cells property was never used
by the pin controller driver. This patch removes it.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

IMX6 has been (ab)using the gic_arch_extn to provide
wakeup from suspend, and it makes a lot of sense to convert
this code to use stacked domains instead.

This patch does just this, updating the DT files to actually
reflect what the HW provides.

BIG FAT WARNING: because the DTs were so far lying by not
exposing the fact that the GPC block is actually the first
interrupt controller in the chain, kernels with this patch
applied wont have any suspend-resume facility when booted
with old DTs, and old kernels with updated DTs won't even boot.
Tested-by: Stefan Agner <stefan@agner.ch>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add support for the CLAA057VC01CW display.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add some defines currently missing, fix ordering to make the list
sorted by (mux_reg, mux_val), make sure pins are grouped by mux_reg.

The same definitions are missing from the old pinmux header
(arch/arm/mach-imx/iomux-mx25.h) but as only legacy machine support uses
that and therefor the existing list is obviously good enough I didn't
spend the effort to add the corresponding definitions there, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Noticed while looking over the pad definitions. None of the bogus
definitions is used in-tree.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

It may be useful to disable the internal rtc snvs-rtc because an
external rtc is available. This patch adds a label so that board files
can disable this rtc.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Sebastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Sebastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Sebastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Sebastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Sebastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The MIPI DSI node contains some ports which represent possible DRM CRTCs
it can connect with.  Each port has a 'reg' property embedded.  This
property will be wrongly interpretted by the MIPI DSI bus driver, because
the driver will take each subnode which contains a 'reg' property as a
DSI peripheral device.  This patch moves the existing MIPI DSI ports into
a new 'ports' node so that the MIPI DSI bus driver may distinguish its
DSI peripheral device(s) from the existing ports.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Since imx6sx-sdb reva board is experimental and will not be used
formally (eg, no software release based on it), we set revb board
as the formal imx6sx-sdb board.

The imx6sx-sdb uses pfuse200 as pmic which has only one power supply
for both VDDARM_IN and VDDSOC_IN, so VDDARM_IN and VDDSOC_IN have to
use the same (higher one in the same frequency) one as its power supply,
that's the reason we override the OPP setting in board dts file.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The imx6sx sdb board has two revisions, the current mainline one
is reva which is experimental and mainly for internal use. In
this commit, we rename imx6sx-sdb.dts to imx6sx-sdb.dtsi, and
move the reva dedicated contents to imx6sx-sdb-reva.dts.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

MCP2515 CAN controller is available on Colibri Evaluation board.
Hence enable MCP2515 CAN.
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

We do not have CONFIG_MACH_MX25_3DS platform anymore, so update the defconfig.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

platform-imxdi_rtc.c is only used by mx25, so it can safely go away now that
mx25 has been converted to dt.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

As mx25 has been converted to a dt-only platform, we do not need the "mx25.h"
header file anymore.

Remove it and also clean up all the mx25 occurences from the platform helper
code.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

We use dynamic memory mapping when using dt, so remove all the static mappings.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

We should use dt to retrieve the IIM base address.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

mx25_clocks_init() is only used to register the clocks for non-dt platforms.

As mx25 has been converted to a dt-only platform, we can safely remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Depend the MXC debug board on machines which actually support it.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

As mx25 is a dt-only platform, we can get rid of platform code support files,
which are unused now.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

As there is no more mx25 board files, we can turn mx25 into a dt-only platform.

Rename imx25-dt.c to mach-imx25.c to be consistent with the other i.MX SoCs.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

eukrea mx25 is well supported in device tree, so let's get rid of its board
files.

Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

When generic pm domain support is enabled, the PGC can be used
to completely gate power to the PU power domain containing GPU3D,
GPU2D, and VPU cores.
This code triggers the PGC powerdown sequence to disable the GPU/VPU
isolation cells and gate power and then disables the PU regulator.
To reenable, the reverse powerup sequence is triggered after the PU
regulator is enabled again.
The GPU and VPU devices in the PU power domain temporarily need
to be clocked during powerup, so that the reset machinery can work.

[Avoid explicit regulator enabling in probe, unless !PM]
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The i.MX6 contains a power controller that controls power gating and
sequencing for the SoC's power domains.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add binding documentation for CPU configuration and interrupt router
submodule of the Miscellaneous System Control Module. The MSCM is
used in all variants of Freescale Vybrid SoC's.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://lkml.kernel.org/r/1425249689-32354-3-git-send-email-stefan@agner.chSigned-off-by: Jason Cooper <jason@lakedaemon.net>

This adds support for Vybrid's interrupt router. On VF6xx models,
almost all peripherals can be used by either of the two CPU's,
the Cortex-A5 or the Cortex-M4. The interrupt router routes the
peripheral interrupts to the configured CPU.

This IRQ chip driver configures the interrupt router to route
the requested interrupt to the CPU the kernel is running on.
The driver makes use of the irqdomain hierarchy support. The
parent is given by the device tree. This should be one of the
two possible parents either ARM GIC or the ARM NVIC interrupt
controller. The latter is currently not yet supported.

Note that there is no resource control mechnism implemented to
avoid concurrent access of the same peripheral. The user needs
to make sure to use device trees which assign the peripherals
orthogonally. However, this driver warns the user in case the
interrupt is already configured for the other CPU. This provides
a poor man's resource controller.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://lkml.kernel.org/r/1425249689-32354-2-git-send-email-stefan@agner.chSigned-off-by: Jason Cooper <jason@lakedaemon.net>