The NAND expansion card (PROC143E1) connects over the User/MCU/PRU
Expansion port on the am62-lp-sk EVM.

The following pins are shared between McASP1 and GPMC-NAND so
both cannot work simultaneously.

Pin name	McASP1 function		GPMC function
========	===============		=============
J17		MCASP1_AXR0		GPMC0_WEN
P21		MCASP1_AFSX		GPMC0_WAIT0
K17		MCASP1_ACLKX		GPMC0_BE0N_CLE
K20		MCASP1_AXR2		GPMC0_ADVN_ALE

The factory default sets the pins for McASP1 use. (i.e.
Resistor Array RA1 installed, RA4 not installed).

For NAND use, RA1 has to be removed and RA4 must be
installed.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240622-am62lp-sk-nand-v1-2-caee496eaf42@kernel.orgSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Add GPMC and ELM device tree nodes for AM62 SoC family.
Signed-off-by: Nitin Yadav <n-yadav@ti.com>
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240622-am62lp-sk-nand-v1-1-caee496eaf42@kernel.orgSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

The audio support on J722S-EVM is using TLV320AIC3106[0] codec
connected to McASP1 serializers.

- Add the nodes for sound-card, audio codec and McASP1.
- Add hog for TRC_MUX_SEL to select between McASP and TRACE signals
- Add hogs for GPIO_AUD_RSTn and MCASP1_FET_SEL which is used to
  switch between HDMI audio and codec audio.
- Add pinmux for MCASP1 and AUDIO_EXT_REFCLK1.

[0]: <https://www.ti.com/lit/gpn/TLV320AIC3106>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240625113301.217369-3-j-choudhary@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

On J722S SoC, the AUDIO_REFCLK1 can be used as input to external
peripherals when configured through CTRL_MMR.
Add audio_refclk1 node which would be used as system clock for the
audio codec TLV320AIC3106.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Link: https://lore.kernel.org/r/20240625113301.217369-2-j-choudhary@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

AM68 SK has an OSPI NOR flash on its SOM connected to OSPI0 instance.
Enable support for the same. Also, describe the OSPI flash partition
information through the device tree, according to the offsets in the
bootloader.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20240622161835.3610348-1-u-kumar1@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Add an overlay to change from the default OSPI NOR to QSPI NOR
for all am6xx-phycore-som boards.
The EEPROM on am6xx-phycore-soms contains information about the
configuration of the SOM. The standard configuration of the SOM
has an ospi nor, but if qspi nor is populated, the EEPROM will
indicate that change and we can use this overlay to cleanly change to
qspi nor.
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Link: https://lore.kernel.org/r/20240621233143.2077941-1-nmorrisson@phytec.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

MIT license was added to the AM64x SoC DTSIs in commit 6248b20e
("arm64: dts: ti: k3-am64: Add MIT license along with GPL-2.0"). Apply
the same license change to the TQMa64xxL SoM and MBaX4XxL baseboard
Device Trees.

The copyright year is updated to indicate the license change.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20240625110244.9881-1-matthias.schiffer@ew.tq-group.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

In current configuration, nau8822 codec on development carrier board
provides distorted audio output. This happens due to reference clock
is fixed to 25MHz and no PLL is enabled. Following is the calculation
of deviation error for different frequencies:

44100Hz:

fs = 256 (fixed)
prescaler = 2
target frequency = 44100 * 256 * 2 = 22579200
deviation = 22579200 vs 25000000 = 9.6832%

48000Hz:

fs = 256 (fixed)
prescaler = 2
target frequency = 48000 * 256 * 2 = 24576000
deviation = 24576000 vs 25000000 = 1.696%

Enabling nau822 PLL via providing mclk-fs property to simple-audio-card
configures clocks properly, but also adjusts audio reference clock
(mclk), which in case of TI AM62 should be avoided, as it only
supports 25MHz output [1][2].

This change enables PLL on nau8822 by providing mclk-fs, and moves
away audio reference clock from DAI configuration, which prevents
simple-audio-card to adjust it before every playback [3].

[1]: https://e2e.ti.com/support/processors-group/processors/f/processors-forum/1175479/processor-sdk-am62x-output-audio_ext_refclk0-as-mclk-for-codec-and-mcbsp/4444986#4444986
[2]: https://e2e.ti.com/support/processors-group/processors/f/processors-forum/1188051/am625-audio_ext_refclk1-clock-output---dts-support/4476322#4476322
[3]: sound/soc/generic/simple-card-utils.c#L441
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20240418105730.120913-1-andrejs.cainikovs@gmail.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

As there is no child node in crypto node, remove the properties
that are not needed.
Signed-off-by: Kamlesh Gurudasani <kamlesh@ti.com>
Link: https://lore.kernel.org/r/20240618-remove-ranges-v1-1-35d68147e9bf@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Add the node for sa3ul crypto accelerator.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Kamlesh Gurudasani <kamlesh@ti.com>
Link: https://lore.kernel.org/r/20240617-crytpo-am62a-v2-1-dc7a14f2635b@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

The IEP0 SYNC_OUT0 pins are used for PPS out on AM64 EVM.
Configure its PINMUX here.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://lore.kernel.org/r/20240614100829.3919008-1-danishanwar@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

I2C1 controller controls io-expander which provides power to voltage
regulator vdd_mmc1 for MMC SD using a gpio line.

Add bootph-all to the pinmux node for this instance, as this is used during
SPL stage too by the bootloader while using SD boot mode as without this
the SD boot mode fails with below error when using this device-tree in
u-boot:

"Timed out in wait_for_event: status=0000
Check if pads/pull-ups of bus are properly configured
Timed out in wait_for_event: status=0000
Check if pads/pull-ups of bus are properly configured
"
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Link: https://lore.kernel.org/r/20240614123532.203983-1-devarsht@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Certain device-tree node properties of shared device-tree nodes are
different between the AM62P and J722S SoCs. To avoid overriding the
properties and to avoid redefining the nodes in the k3-{soc}-main.dtsi
having such SoC specific properties, move the properties to the SoC
specific k3-{soc}-main.dtsi files.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Acked-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240615081600.3602462-9-s-vadapalli@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Enable PCIe0 instance of PCIe in Root Complex mode of operation with Lane 0
of the SERDES1 instance of SERDES. Also enable USB0 instance of USB to
interface with the Type-C port via the USB hub, by configuring the pin P05
of the GPIO expander on the EVM. Enable USB1 instance of USB in SuperSpeed
mode of operation with Lane 0 of the SERDES0 instance of SERDES.
Co-developed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Acked-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240615081600.3602462-8-s-vadapalli@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

J722S SoC has two instances of SERDES namely SERDES0 and SERDES1 and one
instance of PCIe namely PCIe0. Both SERDES0 and SERDES1 are single lane
SERDES. The PCIe0 instance of PCIe is a Gen3 single lane PCIe controller.

Since SERDES and PCIe are not present on AM62P SoC, add the device-tree
nodes corresponding to them in the J722S SoC specific "k3-j722s-main.dtsi"
file.
Co-developed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Acked-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240615081600.3602462-7-s-vadapalli@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

The SERDES0 and SERDES1 instances of SERDES on J722S are single lane
SERDES which are individually muxed across different peripherals.

LANE0 of SERDES0 is muxed between USB and CPSW while LANE0 of SERDES1 is
muxed between PCIe and CPSW.

Define the lane-muxing macros to be used as the idle state values.
Co-developed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240615081600.3602462-6-s-vadapalli@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Update "k3-j722s.dtsi" to include "k3-am62p-j722s-common-{}".dtsi files in
order to reuse the nodes shared with AM62P. Also include the J722S specific
"k3-j722s-main.dtsi".

Since the J7 family of SoCs has the k3-{soc}.dtsi file organized as:
k3-{soc}.dtsi = CPU + Cache + CBASS-Ranges + "Peripheral-Includes"
switch the "k3-j722s.dtsi" file to the same convention.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Acked-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240615081600.3602462-5-s-vadapalli@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Introduce the "k3-j722s-main.dtsi" file to contain main domain peripherals
that are specific to J722S SoC and are not shared with AM62P. The USB1
instance of the USB controller on J722S is different from that on AM62P.
Thus, add the USB1 node in "k3-j722s-main.dtsi".
Co-developed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Acked-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240615081600.3602462-4-s-vadapalli@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

The USB1 instance of USB controller on AM62P is different from the USB1
instance of USB controller on J722S. Thus, move the USB1 instance from
the shared "k3-am62p-j722s-common-main.dtsi" file to the AM62p specific
"k3-am62p-main.dtsi" file. Include "k3-am62p-main.dtsi" in "k3-am62p.dtsi".
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Acked-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240615081600.3602462-3-s-vadapalli@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

The AM62P and J722S SoCs share most of the peripherals. With the aim of
reusing the existing k3-am62p-{mcu,main,thermal,wakeup}.dtsi files for
J722S SoC, rename them to indicate that they are shared with the J722S SoC.

The peripherals that are not shared will be moved in the upcoming patches
to the respective k3-{soc}-{mcu,main,wakeup}.dtsi files without "common" in
the filename, emphasizing that they are not shared.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Acked-by: Andrew Davis <afd@ti.com>
Acked-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240615081600.3602462-2-s-vadapalli@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

The NAND expansion card plugs in over the HSE (High Speed Expansion)
connector. Add support for it.

We add the ranges property to the GPMC node instead of the NAND
overlay file to prevent below warnings.

/fragment@3/__overlay__: Relying on default #address-cells value
/fragment@3/__overlay__: Relying on default #size-cells value

As GPMC is dedicated for NAND use on this board, it should be OK.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240614-am642-evm-nand-v5-1-acf760896239@kernel.orgSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Add an overlay to disable the spi nor for all am6xx-phycore-som
boards.
The EEPROM on am6xx-phycore-soms contains information about the
configuration of the SOM. The standard configuration of the SOM
has an ospi nor, but if no nor is populated, the EEPROM will indicate
that change and we can use this overlay to cleanly disable the
spi nor.
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Link: https://lore.kernel.org/r/20240613230759.1984966-5-nmorrisson@phytec.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Add an overlay to disable the rtc for all am6xx-phycore-som boards.
The EEPROM on am6xx-phycore-soms contains information about the
configuration of the SOM. The standard configuration of the SOM
has an rtc, but if no rtc is populated, the EEPROM will indicate that
change and we can use this overlay to cleanly disable the rtc.
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Link: https://lore.kernel.org/r/20240613230759.1984966-4-nmorrisson@phytec.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Add an overlay to disable the eth phy for all am6xx-phycore-som
boards.
The EEPROM on am6xx-phycore-soms contains information about the
configuration of the SOM. The standard configuration of the SOM
has an ethernet phy, but if no ethernet phy is populated, the EEPROM
will indicate that change and we can use this overlay to cleanly
disable the ethernet phy.
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Link: https://lore.kernel.org/r/20240613230759.1984966-3-nmorrisson@phytec.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Label the spi nor as serial_flash. This allows us to disable the
flash with an overlay common to all am6xx-phycore-som boards.
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Link: https://lore.kernel.org/r/20240613230759.1984966-2-nmorrisson@phytec.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

J721E common processor board can be interfaced with the infotainment
expansion board[0] to enable the following audio/video interfaces in
addition to the peripherals provided by the common processor board:
- Two Audio codecs each with three Stereo Inputs and four Stereo Outputs
- Audio input over FPD Link III
- Digital Audio Interface TX/RX
- HDMI/FPD LINK III Display out
- LI/OV Camera input

Add support for TFP410 HDMI bridge located on the Infotainment Expansion
Board (connected to J46 & J51).
Add a HDMI connector node and connect the endpoints as below:
DSS => TFP410 bridge => HDMI connector
Also add the pinmux data and board muxes for DPI.

Rest of the peripherals are not added as of now.

[0]: <https://www.ti.com/lit/ug/spruit0a/spruit0a.pdf>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[j-choudhary@ti.com: minor cleanup]
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20240613093706.480700-1-j-choudhary@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Add an overlay to enable PCIe on the am642-phyboard-electra. The
serdes is muxed from USB to PCIe, so we are restricted to USB2 while
using this overlay.
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240613195012.1925920-3-nmorrisson@phytec.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Remove pinmuxing for PCIe so that we can add it in an overlay.
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240613195012.1925920-2-nmorrisson@phytec.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Add dts nodes for 6 EHRPWM instances on SoC.
Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20240603112938.2188510-1-u-kumar1@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

The SK-AM64 board has two TMP100 temperature sensors, add these here.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240612183826.121856-1-afd@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

The AM69-SK board has 3 instances of PCIe namely PCIe0, PCIe1 and PCIe3.
The x4 PCIe0 instance is connected to a Card Edge connector via SERDES1.
The x2 PCIe1 instance is connected to an M.2 M Key connector via SERDES0.
The x1 PCIe3 instance is connected to an M.2 E Key connector via SERDES0.

Add device-tree support for enabling all 3 PCIe instances in Root-Complex
mode of operation.
Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20240529082259.1619695-5-s-vadapalli@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Add overlay to enable the PCIe0 and PCIe1 instances of PCIe on J784S4-EVM
in Endpoint mode of operation.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20240529082259.1619695-4-s-vadapalli@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Enable PCIe0 and PCIe1 instances of PCIe in Root Complex mode of
operation on J784S4 EVM. The lanes of PCIe0 are connected to Serdes1
instance of Serdes while the lanes of PCIe1 are connected to Serdes0
instance of Serdes in J784S4 SoC. Despite both PCIe instances supporting
up to 4 Lanes, since the physical connections to the PCIe connector
corresponding to the PCIe1 instance of PCIe are limited to 2 Lanes on
the J784S4 EVM, update the "num-lanes" property of PCIe1 accordingly.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20240529082259.1619695-3-s-vadapalli@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

TI's J784S4 SoC has four instances of Gen3 PCIe Controllers namely
PCIe0, PCIe1, PCIe2 and PCIe3. PCIe0 and PCIe1 are 4-Lane controllers
while PCIe2 and PCIe3 are 2-Lane controllers.

Add support for the Root Complex Mode of operation of these PCIe instances.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20240529082259.1619695-2-s-vadapalli@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Add the "ethernet-mac-syscon" node within "wkup_conf" node corresponding to
the CTRLMMR_MAC_IDx registers within the CTRL_MMR space. Assign the
compatible "ti,am62p-cpsw-mac-efuse" to enable "syscon_regmap" operations
on these registers. The MAC Address programmed in the eFuse is accessible
through the CTRLMMR_MAC_IDx registers. The "ti,syscon-efuse" device-tree
property points to the CTRLMMR_MAC_IDx registers, allowing the CPSW driver
to fetch the MAC Address and assign it to the network interface associated
with CPSW3G MAC Port 1.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240604104425.3770037-1-s-vadapalli@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

The am625 is capable of running at 1.4 GHz when VDD_CORE is increased
from 0.75V to 0.85V. Increasing the voltage while the AM625 is
running has not been validated by TI, so we provide an overlay so that
people may choose to run at 1.4 GHz if they need the additional
performance.
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Link: https://lore.kernel.org/r/20240425221925.1781226-1-nmorrisson@phytec.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

On SK-AM62P, McASP1 uses two pins for communicating with the codec over
I2S protocol. One of these pins (AXR0) is used for audio playback (TX)
so the direction of the pin should be OUTPUT.

Fixes: c00504ea ("arm64: dts: ti: k3-am62p5-sk: Updates for SK EVM")
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240606-mcasp_fifo_drop-v2-7-8c317dabdd0a@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

McASP AFIFOs are not necessary with UDMA-P/BCDMA as there is buffering
on the DMA IP. Drop these for better audio latency.

Fixes: 28c0cf16 ("arm64: dts: ti: k3-am625-phyboard-lyra-rdk: Add Audio Codec")
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240606-mcasp_fifo_drop-v2-6-8c317dabdd0a@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

McASP AFIFOs are not necessary with UDMA-P/BCDMA as there is buffering
on the DMA IP. Drop these for better audio latency.

Fixes: 316b8024 ("arm64: dts: ti: add verdin am62")
Acked-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240606-mcasp_fifo_drop-v2-5-8c317dabdd0a@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

McASP AFIFOs are not necessary with UDMA-P/BCDMA as there is buffering
on the DMA IP. Drop these for better audio latency.

Fixes: 1f7226a5 ("arm64: dts: ti: k3-am625-beagleplay: Add HDMI support")
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240606-mcasp_fifo_drop-v2-4-8c317dabdd0a@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>