- 11 Apr, 2022 2 commits
-
-
Toke Høiland-Jørgensen authored
The comment above the ieee80211_tx_info_clear_status() helper was somewhat confusing as to which fields it was or wasn't clearing. So replace it by something that is hopefully more, well, clear. Signed-off-by:
Toke Høiland-Jørgensen <toke@toke.dk> Link: https://lore.kernel.org/r/20220404210108.2684907-1-toke@toke.dkSigned-off-by:
Johannes Berg <johannes.berg@intel.com>
-
Lorenzo Bianconi authored
Even if it is not a real issue since ieee80211_set_after_csa_beacon() or ieee80211_set_after_color_change_beacon() are run only when csa or bcc is active, move next_beacon check before running ieee80211_assign_beacon routine. Signed-off-by:
Lorenzo Bianconi <lorenzo@kernel.org> Link: https://lore.kernel.org/r/041764ed7e9781bcee66c33b41f1365aa4205932.1649327683.git.lorenzo@kernel.orgSigned-off-by:
-
- 06 Apr, 2022 38 commits
-
-
Meng Tang authored
Use DEVICE_ATTR_*() helper instead of plain DEVICE_ATTR, which makes the code a bit shorter and easier to read. Signed-off-by:
Meng Tang <tangmeng@uniontech.com> Signed-off-by:
Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220406015444.14408-1-tangmeng@uniontech.com
-
Christophe Leroy authored
powerpc's asm/prom.h brings some headers that it doesn't need itself. In order to clean it up, first add missing headers in users of asm/prom.h Signed-off-by:
Christophe Leroy <christophe.leroy@csgroup.eu> Signed-off-by:
-
Haowen Bai authored
crypt and crypt->ops could be null, so we need to checking null before dereference Signed-off-by:
Haowen Bai <baihaowen@meizu.com> Signed-off-by:
-
Haowen Bai authored
fix warning reported by smatch: drivers/net/wireless/broadcom/b43/phy_n.c:585 b43_nphy_adjust_lna_gain_table() warn: assigning (-2) to unsigned variable '*(lna_gain[0])' Signed-off-by:
-
Haowen Bai authored
fix warning reported by smatch: drivers/net/wireless/broadcom/b43legacy/phy.c:1181 b43legacy_phy_lo_b_measure() warn: assigning (-772) to unsigned variable 'fval' Signed-off-by:
-
Chris Chiu authored
RTL8188CUS/RTL8192CU(gen1) don't support rate adaptive report hence no real txrate info can be retrieved. The vendor driver reports the highest rate in HT capabilities from the IEs to avoid empty txrate. This commit initiates the txrate information with the highest supported rate negotiated with AP. The gen2 chip keeps update the txrate from the rate adaptive reports, and gen1 chips at least have non-NULL txrate after associated. Signed-off-by:
Chris Chiu <chris.chiu@canonical.com> Signed-off-by:
-
Chris Chiu authored
Fill up the available TX/RX antenna so the iw commands can show correct antenna information for different chips. Signed-off-by:
-
Jakob Koschel authored
To move the list iterator variable into the list_for_each_entry_*() macro in the future it should be avoided to use the list iterator variable after the loop body. To *never* use the list iterator variable after the loop it was concluded to use a separate iterator variable instead of a found boolean [1]. This removes the need to use a found variable and simply checking if the variable was set, can determine if the break/goto was hit. Link: https://lore.kernel.org/all/CAHk-=wgRr_D8CB-D9Kg-c=EHreAsk5SqXPwr9Y7k9sA6cWXJ6w@mail.gmail.com/Signed-off-by:
Jakob Koschel <jakobkoschel@gmail.com> Acked-by:
Ping-Ke Shih <pkshih@realtek.com> Signed-off-by:
-
Ulf Hansson authored
Keeping the power to the SDIO card during system wide suspend, consumes energy. Especially on battery driven embedded systems, this can be a problem. Therefore, let's change the behaviour into allowing the SDIO card to be powered off, unless WOWL is supported and enabled. Note that, the downside from this change, is that during system resume the SDIO card needs to be re-initialized and the FW must be re-programmed. Even if this may take some time to complete, it should we worth it, rather than draining the battery. Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Tested-by:
Christophe Roullier <christophe.roullier@foss.st.com> Reviewed-by:
Yann Gautier <yann.gautier@foss.st.com> Signed-off-by:
-
Niels Dossche authored
cfg80211_ch_switch_notify uses ASSERT_WDEV_LOCK to assert that net_device->ieee80211_ptr->mtx (which is the same as priv->wdev.mtx) is held during the function's execution. mwifiex_dfs_chan_sw_work_queue is one of its callers, which does not hold that lock, therefore violating the assertion. Add a lock around the call. Disclaimer: I am currently working on a static analyser to detect missing locks. This was a reported case. I manually verified the report by looking at the code, so that I do not send wrong information or patches. After concluding that this seems to be a true positive, I created this patch. However, as I do not in fact have this particular hardware, I was unable to test it. Reviewed-by:
Brian Norris <briannorris@chromium.org> Signed-off-by:
Niels Dossche <dossche.niels@gmail.com> Signed-off-by:
-
Po Hao Huang authored
Without this patch, hw scan won't stay long enough on DFS/passive channels. Found previous logic error and fix it. Signed-off-by:
Po Hao Huang <phhuang@realtek.com> Signed-off-by:
-
Ching-Te Ku authored
Turn off coexistence driver control, let firmware can control the traffic during scan. This prevents potential unexpected behavior of the BT driver. Signed-off-by:
Ching-Te Ku <ku920601@realtek.com> Signed-off-by:
-
Po Hao Huang authored
Add a dummy function for packet offload to eliminate warning message "c2h class 1 func 2 not support". This c2h is for debug purpose and its presence itself can do the work, so further parsing won't be required for now. Signed-off-by:
-
Po Hao Huang authored
Previously we only consider single interface's status, idle mode behavior could be unexpected when multiple interfaces is active. Change to enter/leave idle mode by mac80211's configuration state. Signed-off-by:
-
Ping-Ke Shih authored
ptcl_init, standing for protocol initialization, is updated to the latest version. Signed-off-by:
-
Ping-Ke Shih authored
TMAC is short for TX MAC, and this patch is to configure FIFO thresholds. Signed-off-by:
-
Ping-Ke Shih authored
Configure NAV function and its parameters. Signed-off-by:
-
Ping-Ke Shih authored
Update IC specific settings accordingly. Signed-off-by:
-
Ping-Ke Shih authored
The security setting of 8852A and 8852C are different, so change the settings accordingly. Signed-off-by:
-
Ping-Ke Shih authored
CMAC is Control MAC, and this patch is to turn on CR (control registers) protection. Signed-off-by:
-
Ping-Ke Shih authored
The v1 chip use specific functions to enable and disable BB/RF. Signed-off-by:
-
Ping-Ke Shih authored
The v1 chip has additional setting of STA scheduler, so add it. Signed-off-by:
-
Ping-Ke Shih authored
DMAC is short for data MAC. 8852C has more settings than 8852A, so add them. Signed-off-by:
-
Ping-Ke Shih authored
Configure L1 settings of enter and exit. Signed-off-by:
-
Ping-Ke Shih authored
Add setting to support 8852ce. Signed-off-by:
-
Ping-Ke Shih authored
Address info registers are used to configure size of DMA address info to point skb->data. With different size, it can support different number of scatters. Signed-off-by:
-
Ping-Ke Shih authored
Add LTR handle to PCI deinit as well. Signed-off-by:
-
Chia-Yuan Li authored
The pre_init is used to initialize partial PCI function during PCI probe. It doesn't need to initialize all functions, so probe can be faster. Signed-off-by:
Chia-Yuan Li <leo.li@realtek.com> Signed-off-by:
-
Ping-Ke Shih authored
Refine operating mode function to support variant chips. Signed-off-by:
-
Ping-Ke Shih authored
The PCI code of 8852AE and 8852CE are different, but the flow and register names are similar. To reuse the code, add a struct to define register or value accordingly. We also use chip id to control the slightly different flow. Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.gitKalle Valo authored
ath.git patches for v5.19. Major changes: ath11k * Wake-on-WLAN support for QCA6390 and WCN6855 * device recovery (firmware restart) support for QCA6390 and WCN6855 wcn36xx * support for transmit rate reporting to user space
-
Kalle Valo authored
No need to have goto for a return statement, so simplify the code. While at it, print warning messages if power up calls fail. No functional changes. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2 Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220401173042.17467-4-kvalo@kernel.org
-
Kalle Valo authored
While reviewing the mhi.c I noticed we were just ignoring the errors coming from MHI subsystem during suspend and resume. Add proper checks and warning messages. Also pass the error value to callers. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2 Signed-off-by:
-
Kalle Valo authored
State machines are difficult to understand and in this case it's just useless, which is shown by the diffstat. So remove it entirely to make the code simpler. No functional changes. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2 Signed-off-by:
-
Ping-Ke Shih authored
The smatch reports: rtw8852a.c:1857 rtw8852a_btc_set_wl_txpwr_ctrl() error: uninitialized symbol '_cur'. rtw8852a.c:1858 rtw8852a_btc_set_wl_txpwr_ctrl() error: uninitialized symbol '_cur'. This is because rtw89_mac_txpwr_read32() can possibly return before setting argument _cur, and the caller will use the uninitialized value. To fix this problem, check the return value of rtw89_mac_txpwr_read32(). Signed-off-by:
-
Ping-Ke Shih authored
8852C uses different fields to represent RX bandwidth. Since other fields are the same, I check chip_id to get bandwidth instead of creating another v1 function. Signed-off-by:
-
Ping-Ke Shih authored
The newer chip will generate security header itself, so don't set IEEE80211_KEY_FLAG_GENERATE_IV in this kind of chip. But, it needs to fill key_index, PN and 802.11 header length to TX descriptor, and then hardware uses these to generate security header. Signed-off-by:
-
Ping-Ke Shih authored
The txdesc is descriptor related to skb->data. The v1 version contains 8 dwords txwd_body and 6 dwords txwd_info, and the format is also different from original one. Signed-off-by:
-
