This patch replaces tg3's private SPEED_INVALID and DUPLEX_INVALID
definitions with SPEED_UNKNOWN and DUPLEX_UNKNOWN respectively.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes the unneeded link_config.orig_* members.  When the
phy is in a low power state, the TG3_PHYFLG_IS_LOW_POWER flag solely
determines how the link is configured.  When the phy is powered back up,
it can resume using the original settings.

For the phylib case, the link configuration still needs to be saved, but
since the phylib maintains its own configuration, we can repurpose the
(unused in this case) tg3 link configuration members.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When tg3 devices are shutdown, the driver uses the
TG3_PHYFLG_IS_LOW_POWER flag to enable a static phy configuration.
Any attempt to use the link configuration variables is dead code.  This
patch removes such code.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Detecting the ASIC revision of a device is getting to be an increasingly
complex process.  This patch consolidates all the ASIC rev detection
code to a single routine for better maintainability.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The tg3 driver needs to submit a few phy register values to the UMP
firmware each time the link state changes.  Up until now, the driver
would wait for the previous event to complete, then proceed to gather
data through a series of phy accesses.  Since phy accesses are
relatively slow, it is possible for another thread to attempt to submit
its own event while the UMP code is still construction its message.

This patch seeks to minimize the collision window as much as possible by
preloading the phy data.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On newer devices, the hardware expects the NVRAM address register
to be written only once per NVRAM page.  To do otherwise causes NVRAM
corruption.  This patch fixes the problem.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When checking the autoneg advertisements, the driver failed to include
the master and master enable bits for the bcm5701.  This patch fixes the
problem.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the tg3 interface is down, the driver will return ethtool stats
uninitialized.  This patch zeroes out the destination stat buffer in
such a case.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A bug was found in the new DMA engine for the 57766.  This patch
disables it, which causes the device to fallback to the old DMA engine.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Per ./Documentation/CodingStyle, goto statements are acceptable for the
centralized exiting of functions when there are multiple exit points which
share common work such as cleanup.  When no common work is required for
multiple exit points, the function should just return at these exit points
instead of doing an unnecessary jump to a centralized return.  This patch
cleans up the inappropriate use of goto statements, and removes unnecessary
variables (or move to a smaller scope) where possible as a result of the
cleanups.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In the unlikely event that e1000_poll_fiber_serdes_link_generic() is called
and it returns an error, the returned error code value is not propagated to
the caller of e1000e_setup_fiber_serdes_link().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In the unlikely event that e1000_setup_link_ich8lan() returns an error,
the returned error code value is not propagated to the caller of
e1000_init_hw_ich8lan().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Fall-through to a return statement that effectively does the same.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ret_val gets initialized to -E1000_ERR_NVM and never set differently, so
get rid of it and just return -E1000_ERR_NVM.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In the unlikely event that e1e_wphy() returns an error, the returned error
code is not propogated to the caller of e1000_set_d3_lplu_state_ich8lan().
With this change, there is a rare possibility that ret_val might not get
set so it must be initialized.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

net/sched/sch_plug.c:211:18: warning: symbol 'plug_qdisc_ops' was not
declared. Should it be static?
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When building frag_list, head truesize should be sum of all frag
truesize.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

skb_gro_receive() doesnt update truesize properly when adding one skb to
frag_list.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch moves a comment in the transmit path to a better location.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch eliminates the unneeded tg3_halt_cpu() prototype and moves
the tg3_setup_phy() prototype closer to where it is needed.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch relocates tg3_find_peer to eliminate a prototype.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch moves the tg3_nvram_write_block functions higher in the file
to eliminate a prototype.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch moves __tg3_set_rx_mode above its first use and moves
tg3_set_rx_mode down closer to where the netdev_ops functions should be.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch moves tg3_change_mtu to a better location.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch moves tg3_reset_task further down in the file where it makes
more sense to be.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch relocates tg3_restart_hw() to a better location.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 3fa2a1df (virtio-net: per cpu 64 bit stats (v2)) added extra
__percpu qualifiers and sparse errors.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

These are a few instances of returning a value that can only be 0 so just
use a 'return 0' to make it more obvious.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Just return the appropriate value.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In the unlikely event that e1000e_setup_copper_link() returns an error,
the returned error code value is not propogated to the caller of
e1000_setup_copper_link_80003es2lan().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In the unlikely event that e1e_wphy() returns an error, the returned error
code value is not propogated to the caller of
e1000_cfg_kmrn_10_100_80003es2lan().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In the following functions, rename the generic 'out' goto label to the more
descriptive 'release' to indicate the type of common work that is done
before exiting the functions.  No functional change, cosmetic only.

e1000_sw_lcd_config_ich8lan()
e1000_oem_bits_config_ich8lan()
e1000_init_phy_wakeup()
e1000e_write_phy_reg_bm()
e1000e_read_phy_reg_bm()
e1000e_read_phy_reg_bm2()
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

There are two exit points of e1000e_write_nvm_spi() which require the
nvm->ops.release() function pointer called just before exiting.
Consolidate the two duplicate pieces of common work with a goto.  With
this change, the value ret_val will need to be returned instead of 0.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: David S. Miller <davem@davemloft.net>

Correct spelling "drivr" to "driver" in
drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Correct spelling "modul" to "module" in
drivers/isdn/mISDN/dsp_core.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>