This driver adds pinctrl/GPIO support for Intel Alder Lake-S SoC. The
GPIO controller is based on the next generation GPIO hardware but still
compatible with the one supported by the Intel core pinctrl/GPIO driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

This driver adds pinctrl/GPIO support for Intel Elkhart Lake SoC. The
GPIO controller is based on the next generation GPIO hardware but still
compatible with the one supported by the Intel core pinctrl/GPIO driver.

Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Add a blank line before endif directive in Kconfig for better readability.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

This driver adds pinctrl/GPIO support for Intel Lakefield SoC. The
GPIO controller is based on the next generation GPIO hardware but still
compatible with the one supported by the Intel core pinctrl/GPIO driver.

Cc: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

When GPIO library asks pin control to set the bias, it doesn't pass
any value of it and argument is considered boolean (and this is true
for ACPI GpioIo() / GpioInt() resources, by the way). Thus, individual
drivers must behave well, when they got the resistance value of 1 Ohm,
i.e. transforming it to sane default.

In case of Intel pin control hardware the 5 kOhm sounds plausible
because on one hand it's a minimum of resistors present in all
hardware generations and at the same time it's high enough to minimize
leakage current (will be only 200 uA with the above choice).

Fixes: e57725ea ("pinctrl: intel: Add support for hardware debouncer")
Reported-by: Jamie McClymont <jamie@kwiius.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

2 kOhm bias was never an option in Intel GPIO hardware, the available
matrix is:

	000	none
	001	1 kOhm (if available)
	010	5 kOhm
	100	20 kOhm

As easy to get the 3 resistors are gated separately and according to
parallel circuits calculations we may get combinations of the above where
the result is always strictly less than minimal resistance. Hence,
additional values can be:

	011	~833.3 Ohm
	101	~952.4 Ohm
	110	~4 kOhm
	111	~800 Ohm

That said, convert TERM definitions to be the bit masks to reflect the above.

While at it, enable the same setting for pull down case.

Fixes: 7981c001 ("pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support")
Cc: Jamie McClymont <jamie@kwiius.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.

Remove the quote operator # from compiler_attributes.h __section macro.

Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.

Conversion done using the script at:

    https://lore.kernel.org/lkml/75393e5ddc272dc7403de74d645e6c6e0f4e70eb.camel@perches.com/2-convert_section.plSigned-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@gooogle.com>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

tid_addr is not a "pointer to (pointer to int in userspace)"; it is in
fact a "pointer to (pointer to int in userspace) in userspace".  So
sparse rightfully complains about passing a kernel pointer to
put_user().
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 453431a5 ("mm, treewide: rename kzfree() to
kfree_sensitive()") renamed kzfree() to kfree_sensitive(),
but it left a compatibility definition of kzfree() to avoid
being too disruptive.

Since then a few more instances of kzfree() have slipped in.

Just get rid of them and remove the compatibility definition
once and for all.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If set, use the environment variable GIT_DIR to change the default .git
location of the kernel git tree.

If GIT_DIR is unset, keep using the current ".git" default.

Link: https://lkml.kernel.org/r/c5e23b45562373d632fccb8bc04e563abba4dd1d.camel@perches.comSigned-off-by: Joe Perches <joe@perches.com>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull timer fixes from Thomas Gleixner:
 "A time namespace fix and a matching selftest. The futex absolute
  timeouts which are based on CLOCK_MONOTONIC require time namespace
  corrected. This was missed in the original time namesapce support"

* tag 'timers-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  selftests/timens: Add a test for futex()
  futex: Adjust absolute futex timeouts with per time namespace offset

Pull scheduler fixes from Thomas Gleixner:
 "Two scheduler fixes:

   - A trivial build fix for sched_feat() to compile correctly with
     CONFIG_JUMP_LABEL=n

   - Replace a zero lenght array with a flexible array"

* tag 'sched-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/features: Fix !CONFIG_JUMP_LABEL case
  sched: Replace zero-length array with flexible-array

Pull perf fix from Thomas Gleixner:
 "A single fix to compute the field offset of the SNOOPX bit in the data
  source bitmask of perf events correctly"

* tag 'perf-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: correct SNOOPX field offset

Pull locking fix from Thomas Gleixner:
 "Just a trivial fix for kernel-doc warnings"

* tag 'locking-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  locking/seqlocks: Fix kernel-doc warnings

Pull NTB fixes from Jon Mason.

* tag 'ntb-5.10' of git://github.com/jonmason/ntb:
  NTB: Use struct_size() helper in devm_kzalloc()
  ntb: intel: Fix memleak in intel_ntb_pci_probe
  NTB: hw: amd: fix an issue about leak system resources

Pull i2c fix from Wolfram Sang:
 "Regression fix for rc1 and stable kernels as well"

* 'i2c/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: core: Restore acpi_walk_dep_device_list() getting called after registering the ACPI i2c devs

Pull more cifs updates from Steve French:
 "Add support for stat of various special file types (WSL reparse points
  for char, block, fifo)"

* tag '5.10-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: update internal module version number
  smb3: add some missing definitions from MS-FSCC
  smb3: remove two unused variables
  smb3: add support for stat of WSL reparse points for special file types

Pull more parisc updates from Helge Deller:

 - During this merge window O_NONBLOCK was changed to become 000200000,
   but we missed that the syscalls timerfd_create(), signalfd4(),
   eventfd2(), pipe2(), inotify_init1() and userfaultfd() do a strict
   bit-wise check of the flags parameter.

   To provide backward compatibility with existing userspace we
   introduce parisc specific wrappers for those syscalls which filter
   out the old O_NONBLOCK value and replaces it with the new one.

 - Prevent HIL bus driver to get stuck when keyboard or mouse isn't
   attached

 - Improve error return codes when setting rtc time

 - Minor documentation fix in pata_ns87415.c

* 'parisc-5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  ata: pata_ns87415.c: Document support on parisc with superio chip
  parisc: Add wrapper syscalls to fix O_NONBLOCK flag usage
  hil/parisc: Disable HIL driver when it gets stuck
  parisc: Improve error return codes when setting rtc time

Pull more xen updates from Juergen Gross:

 - a series for the Xen pv block drivers adding module parameters for
   better control of resource usge

 - a cleanup series for the Xen event driver

* tag 'for-linus-5.10b-rc1c-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  Documentation: add xen.fifo_events kernel parameter description
  xen/events: unmask a fifo event channel only if it was masked
  xen/events: only register debug interrupt for 2-level events
  xen/events: make struct irq_info private to events_base.c
  xen: remove no longer used functions
  xen-blkfront: Apply changed parameter name to the document
  xen-blkfront: add a parameter for disabling of persistent grants
  xen-blkback: add a parameter for disabling of persistent grants

Pull SafeSetID updates from Micah Morton:
 "The changes are mostly contained to within the SafeSetID LSM, with the
  exception of a few 1-line changes to change some ns_capable() calls to
  ns_capable_setid() -- causing a flag (CAP_OPT_INSETID) to be set that
  is examined by SafeSetID code and nothing else in the kernel.

  The changes to SafeSetID internally allow for setting up GID
  transition security policies, as already existed for UIDs"

* tag 'safesetid-5.10' of git://github.com/micah-morton/linux:
  LSM: SafeSetID: Fix warnings reported by test bot
  LSM: SafeSetID: Add GID security policy handling
  LSM: Signal to SafeSetID when setting group IDs

Pull random32 updates from Willy Tarreau:
 "Make prandom_u32() less predictable.

  This is the cleanup of the latest series of prandom_u32
  experimentations consisting in using SipHash instead of Tausworthe to
  produce the randoms used by the network stack.

  The changes to the files were kept minimal, and the controversial
  commit that used to take noise from the fast_pool (f227e3ec) was
  reverted. Instead, a dedicated "net_rand_noise" per_cpu variable is
  fed from various sources of activities (networking, scheduling) to
  perturb the SipHash state using fast, non-trivially predictable data,
  instead of keeping it fully deterministic. The goal is essentially to
  make any occasional memory leakage or brute-force attempt useless.

  The resulting code was verified to be very slightly faster on x86_64
  than what is was with the controversial commit above, though this
  remains barely above measurement noise. It was also tested on i386 and
  arm, and build- tested only on arm64"

Link: https://lore.kernel.org/netdev/20200808152628.GA27941@SDF.ORG/

* tag '20201024-v4-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wtarreau/prandom:
  random32: add a selftest for the prandom32 code
  random32: add noise from network and scheduling activity
  random32: make prandom_u32() output unpredictable

Commit 21653a41 ("i2c: core: Call i2c_acpi_install_space_handler()
before i2c_acpi_register_devices()")'s intention was to only move the
acpi_install_address_space_handler() call to the point before where
the ACPI declared i2c-children of the adapter where instantiated by
i2c_acpi_register_devices().

But i2c_acpi_install_space_handler() had a call to
acpi_walk_dep_device_list() hidden (that is I missed it) at the end
of it, so as an unwanted side-effect now acpi_walk_dep_device_list()
was also being called before i2c_acpi_register_devices().

Move the acpi_walk_dep_device_list() call to the end of
i2c_acpi_register_devices(), so that it is once again called *after*
the i2c_client-s hanging of the adapter have been created.

This fixes the Microsoft Surface Go 2 hanging at boot.

Fixes: 21653a41 ("i2c: core: Call i2c_acpi_install_space_handler() before i2c_acpi_register_devices()")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209627Reported-by: Rainer Finke <rainer@finke.cc>
Reported-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Suggested-by: Maximilian Luz <luzmaximilian@gmail.com>
Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Pull block fixes from Jens Axboe:

 - NVMe pull request from Christoph
     - rdma error handling fixes (Chao Leng)
     - fc error handling and reconnect fixes (James Smart)
     - fix the qid displace when tracing ioctl command (Keith Busch)
     - don't use BLK_MQ_REQ_NOWAIT for passthru (Chaitanya Kulkarni)
     - fix MTDT for passthru (Logan Gunthorpe)
     - blacklist Write Same on more devices (Kai-Heng Feng)
     - fix an uninitialized work struct (zhenwei pi)"

 - lightnvm out-of-bounds fix (Colin)

 - SG allocation leak fix (Doug)

 - rnbd fixes (Gioh, Guoqing, Jack)

 - zone error translation fixes (Keith)

 - kerneldoc markup fix (Mauro)

 - zram lockdep fix (Peter)

 - Kill unused io_context members (Yufen)

 - NUMA memory allocation cleanup (Xianting)

 - NBD config wakeup fix (Xiubo)

* tag 'block-5.10-2020-10-24' of git://git.kernel.dk/linux-block: (27 commits)
  block: blk-mq: fix a kernel-doc markup
  nvme-fc: shorten reconnect delay if possible for FC
  nvme-fc: wait for queues to freeze before calling update_hr_hw_queues
  nvme-fc: fix error loop in create_hw_io_queues
  nvme-fc: fix io timeout to abort I/O
  null_blk: use zone status for max active/open
  nvmet: don't use BLK_MQ_REQ_NOWAIT for passthru
  nvmet: cleanup nvmet_passthru_map_sg()
  nvmet: limit passthru MTDS by BIO_MAX_PAGES
  nvmet: fix uninitialized work for zero kato
  nvme-pci: disable Write Zeroes on Sandisk Skyhawk
  nvme: use queuedata for nvme_req_qid
  nvme-rdma: fix crash due to incorrect cqe
  nvme-rdma: fix crash when connect rejected
  block: remove unused members for io_context
  blk-mq: remove the calling of local_memory_node()
  zram: Fix __zram_bvec_{read,write}() locking order
  skd_main: remove unused including <linux/version.h>
  sgl_alloc_order: fix memory leak
  lightnvm: fix out-of-bounds write to array devices->info[]
  ...

Pull io_uring fixes from Jens Axboe:

 - fsize was missed in previous unification of work flags

 - Few fixes cleaning up the flags unification creds cases (Pavel)

 - Fix NUMA affinities for completely unplugged/replugged node for io-wq

 - Two fallout fixes from the set_fs changes. One local to io_uring, one
   for the splice entry point that io_uring uses.

 - Linked timeout fixes (Pavel)

 - Removal of ->flush() ->files work-around that we don't need anymore
   with referenced files (Pavel)

 - Various cleanups (Pavel)

* tag 'io_uring-5.10-2020-10-24' of git://git.kernel.dk/linux-block:
  splice: change exported internal do_splice() helper to take kernel offset
  io_uring: make loop_rw_iter() use original user supplied pointers
  io_uring: remove req cancel in ->flush()
  io-wq: re-set NUMA node affinities if CPUs come online
  io_uring: don't reuse linked_timeout
  io_uring: unify fsize with def->work_flags
  io_uring: fix racy REQ_F_LINK_TIMEOUT clearing
  io_uring: do poll's hash_node init in common code
  io_uring: inline io_poll_task_handler()
  io_uring: remove extra ->file check in poll prep
  io_uring: make cached_cq_overflow non atomic_t
  io_uring: inline io_fail_links()
  io_uring: kill ref get/drop in personality init
  io_uring: flags-based creds init in queue

Pull libata fixes from Jens Axboe:
 "Two minor libata fixes:

   - Fix a DMA boundary mask regression for sata_rcar (Geert)

   - kerneldoc markup fix (Mauro)"

* tag 'libata-5.10-2020-10-24' of git://git.kernel.dk/linux-block:
  ata: fix some kernel-doc markups
  ata: sata_rcar: Fix DMA boundary mask

Pull misc vfs updates from Al Viro:
 "Assorted stuff all over the place (the largest group here is
  Christoph's stat cleanups)"

* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fs: remove KSTAT_QUERY_FLAGS
  fs: remove vfs_stat_set_lookup_flags
  fs: move vfs_fstatat out of line
  fs: implement vfs_stat and vfs_lstat in terms of vfs_fstatat
  fs: remove vfs_statx_fd
  fs: omfs: use kmemdup() rather than kmalloc+memcpy
  [PATCH] reduce boilerplate in fsid handling
  fs: Remove duplicated flag O_NDELAY occurring twice in VALID_OPEN_FLAGS
  selftests: mount: add nosymfollow tests
  Add a "nosymfollow" mount option.

Pull dma-mapping fixes from Christoph Hellwig:

 - document the new dma_{alloc,free}_pages() API

 - two fixups for the dma-mapping.h split

* tag 'dma-mapping-5.10-1' of git://git.infradead.org/users/hch/dma-mapping:
  dma-mapping: document dma_{alloc,free}_pages
  dma-mapping: move more functions to dma-map-ops.h
  ARM/sa1111: add a missing include of dma-map-ops.h

Pull KVM fixes from Paolo Bonzini:
 "Two fixes for this merge window, and an unrelated bugfix for a host
  hang"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: ioapic: break infinite recursion on lazy EOI
  KVM: vmx: rename pi_init to avoid conflict with paride
  KVM: x86/mmu: Avoid modulo operator on 64-bit value to fix i386 build

Pull x86 SEV-ES fixes from Borislav Petkov:
 "Three fixes to SEV-ES to correct setting up the new early pagetable on
  5-level paging machines, to always map boot_params and the kernel
  cmdline, and disable stack protector for ../compressed/head{32,64}.c.
  (Arvind Sankar)"

* tag 'x86_seves_fixes_for_v5.10_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/boot/64: Explicitly map boot_params and command line
  x86/head/64: Disable stack protection for head$(BITS).o
  x86/boot/64: Initialize 5-level paging variables earlier

Given that this code is new, let's add a selftest for it as well.
It doesn't rely on fixed sets, instead it picks 1024 numbers and
verifies that they're not more correlated than desired.

Link: https://lore.kernel.org/netdev/20200808152628.GA27941@SDF.ORG/
Cc: George Spelvin <lkml@sdf.org>
Cc: Amit Klein <aksecurity@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: "Jason A. Donenfeld" <Jason@zx2c4.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: tytso@mit.edu
Cc: Florian Westphal <fw@strlen.de>
Cc: Marc Plumb <lkml.mplumb@gmail.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>

With the removal of the interrupt perturbations in previous random32
change (random32: make prandom_u32() output unpredictable), the PRNG
has become 100% deterministic again. While SipHash is expected to be
way more robust against brute force than the previous Tausworthe LFSR,
there's still the risk that whoever has even one temporary access to
the PRNG's internal state is able to predict all subsequent draws till
the next reseed (roughly every minute). This may happen through a side
channel attack or any data leak.

This patch restores the spirit of commit f227e3ec ("random32: update
the net random state on interrupt and activity") in that it will perturb
the internal PRNG's statee using externally collected noise, except that
it will not pick that noise from the random pool's bits nor upon
interrupt, but will rather combine a few elements along the Tx path
that are collectively hard to predict, such as dev, skb and txq
pointers, packet length and jiffies values. These ones are combined
using a single round of SipHash into a single long variable that is
mixed with the net_rand_state upon each invocation.

The operation was inlined because it produces very small and efficient
code, typically 3 xor, 2 add and 2 rol. The performance was measured
to be the same (even very slightly better) than before the switch to
SipHash; on a 6-core 12-thread Core i7-8700k equipped with a 40G NIC
(i40e), the connection rate dropped from 556k/s to 555k/s while the
SYN cookie rate grew from 5.38 Mpps to 5.45 Mpps.

Link: https://lore.kernel.org/netdev/20200808152628.GA27941@SDF.ORG/
Cc: George Spelvin <lkml@sdf.org>
Cc: Amit Klein <aksecurity@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: "Jason A. Donenfeld" <Jason@zx2c4.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: tytso@mit.edu
Cc: Florian Westphal <fw@strlen.de>
Cc: Marc Plumb <lkml.mplumb@gmail.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>

Non-cryptographic PRNGs may have great statistical properties, but
are usually trivially predictable to someone who knows the algorithm,
given a small sample of their output.  An LFSR like prandom_u32() is
particularly simple, even if the sample is widely scattered bits.

It turns out the network stack uses prandom_u32() for some things like
random port numbers which it would prefer are *not* trivially predictable.
Predictability led to a practical DNS spoofing attack.  Oops.

This patch replaces the LFSR with a homebrew cryptographic PRNG based
on the SipHash round function, which is in turn seeded with 128 bits
of strong random key.  (The authors of SipHash have *not* been consulted
about this abuse of their algorithm.)  Speed is prioritized over security;
attacks are rare, while performance is always wanted.

Replacing all callers of prandom_u32() is the quick fix.
Whether to reinstate a weaker PRNG for uses which can tolerate it
is an open question.

Commit f227e3ec ("random32: update the net random state on interrupt
and activity") was an earlier attempt at a solution.  This patch replaces
it.
Reported-by: Amit Klein <aksecurity@gmail.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Eric Dumazet <edumazet@google.com>
Cc: "Jason A. Donenfeld" <Jason@zx2c4.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: tytso@mit.edu
Cc: Florian Westphal <fw@strlen.de>
Cc: Marc Plumb <lkml.mplumb@gmail.com>
Fixes: f227e3ec ("random32: update the net random state on interrupt and activity")
Signed-off-by: George Spelvin <lkml@sdf.org>
Link: https://lore.kernel.org/netdev/20200808152628.GA27941@SDF.ORG/
[ willy: partial reversal of f227e3ec; moved SIPROUND definitions
  to prandom.h for later use; merged George's prandom_seed() proposal;
  inlined siprand_u32(); replaced the net_rand_state[] array with 4
  members to fix a build issue; cosmetic cleanups to make checkpatch
  happy; fixed RANDOM32_SELFTEST build ]
Signed-off-by: Willy Tarreau <w@1wt.eu>

Pull powerpc fixes from Michael Ellerman:

 - A fix for undetected data corruption on Power9 Nimbus <= DD2.1 in the
   emulation of VSX loads. The affected CPUs were not widely available.

 - Two fixes for machine check handling in guests under PowerVM.

 - A fix for our recent changes to SMP setup, when
   CONFIG_CPUMASK_OFFSTACK=y.

 - Three fixes for races in the handling of some of our powernv sysfs
   attributes.

 - One change to remove TM from the set of Power10 CPU features.

 - A couple of other minor fixes.

Thanks to: Aneesh Kumar K.V, Christophe Leroy, Ganesh Goudar, Jordan
Niethe, Mahesh Salgaonkar, Michael Neuling, Oliver O'Halloran, Qian Cai,
Srikar Dronamraju, Vasant Hegde.

* tag 'powerpc-5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/pseries: Avoid using addr_to_pfn in real mode
  powerpc/uaccess: Don't use "m<>" constraint with GCC 4.9
  powerpc/eeh: Fix eeh_dev_check_failure() for PE#0
  powerpc/64s: Remove TM from Power10 features
  selftests/powerpc: Make alignment handler test P9N DD2.1 vector CI load workaround
  powerpc: Fix undetected data corruption with P9N DD2.1 VSX CI load emulation
  powerpc/powernv/dump: Handle multiple writes to ack attribute
  powerpc/powernv/dump: Fix race while processing OPAL dump
  powerpc/smp: Use GFP_ATOMIC while allocating tmp mask
  powerpc/smp: Remove unnecessary variable
  powerpc/mce: Avoid nmi_enter/exit in real mode on pseries hash
  powerpc/opal_elog: Handle multiple writes to ack attribute

Pull more RISC-V updates from Palmer Dabbelt:
 "Just a single patch set: the remainder of Christoph's work to remove
  set_fs, including the RISC-V portion"

* tag 'riscv-for-linus-5.10-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  riscv: remove address space overrides using set_fs()
  riscv: implement __get_kernel_nofault and __put_user_nofault
  riscv: refactor __get_user and __put_user
  riscv: use memcpy based uaccess for nommu again
  asm-generic: make the set_fs implementation optional
  asm-generic: add nommu implementations of __{get,put}_kernel_nofault
  asm-generic: improve the nommu {get,put}_user handling
  uaccess: provide a generic TASK_SIZE_MAX definition

Pull ARM SoC defconfig updates from Olof Johansson:
 "We keep this in a separate branch to avoid cross-branch conflicts, but
  most of the material here is fairly boring -- some new drivers turned
  on for hardware since they were merged, and some refreshed files due
  to time having moved a lot of entries around"

* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (33 commits)
  ARM: multi_v7_defconfig: add FMC2 EBI controller support
  arm64: defconfig: enable Qualcomm ASoC modules
  arm64: defconfig: qcom: enable GPU clock controller for SM8[12]50
  arm64: defconfig: enable INTERCONNECT for Qualcomm chipsets
  arm64: defconfig: enable the sl28cpld board management controller
  arm64: defconfig: Enable the eLCDIF and Raydium RM67191 drivers
  arm64: defconfig: Enable Qcom SNPS Femto PHY
  ARM: configs: Update Realview defconfig
  ARM: configs: Update Versatile defconfig
  ARM: config: aspeed_g5: Enable IBM OP Panel driver
  ARM: config: aspeed-g5: Enable I2C GPIO mux driver
  ARM: config: aspeed: Fix selection of media drivers
  arm64: defconfig: Enable Samsung S3FWRN5 NFC driver
  ARM: omap2plus_defconfig: enable generic net options
  ARM: omap2plus_defconfig: enable twl4030_madc as a loadable module
  arm64: defconfig: Enable clock driver for ROHM BD718x7 PMIC
  arm64: defconfig: Build ADMA and ACONNECT driver
  arm64: defconfig: Build AHUB component drivers
  arm64: defconfig: Enable Lontium LT9611 driver
  arm64: defcondfig: Enable USB ACM and FTDI drivers
  ...

Pull ARM Devicetree updates from Olof Johansson:
 "As usual, most of the changes are to devicetrees.

  Besides smaller fixes, some refactorings and cleanups, some of the new
  platforms and chips (or significant features) supported are below:

  Broadcom boards:
   - Cisco Meraki MR32 (BCM53016-based)
   - BCM2711 (RPi4) display pipeline support

  Actions Semi boards:
   - Caninos Loucos Labrador SBC (S500-based)
   - RoseapplePi SBC (S500-based)

  Allwinner SoCs/boards:
   - A100 SoC with Perf1 board
   - Mali, DMA, Cetrus and IR support for R40 SoC

  Amlogic boards:
   - Libretch S905x CC V2 board
   - Hardkernel ODROID-N2+ board

  Aspeed boards/platforms:
   - Wistron Mowgli (AST2500-based, Power9 OpenPower server)
   - Facebook Wedge400 (AST2500-based, ToR switch)

  Hisilicon SoC:
   - SD5203 SoC

  Nvidia boards:
   - Tegra234 VDK, for pre-silicon Orin SoC

  NXP i.MX boards:
   - Librem 5 phone
   - i.MX8MM DDR4 EVK
   - Variscite VAR-SOM-MX8MN SoM
   - Symphony board
   - Tolino Shine 2 HD
   - TQMa6 SoM
   - Y Soft IOTA Orion

  Rockchip boards:
   - NanoPi R2S board
   - A95X-Z2 board
   - more Rock-Pi4 variants

  STM32 boards:
   - Odyssey SOM board (STM32MP157CAC-based)
   - DH DRC02 board

  Toshiba SoCs/boards:
   - Visconti SoC and TPMV7708 board"

* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (638 commits)
  ARM: dts: nspire: Fix SP804 users
  arm64: dts: lg: Fix SP804 users
  arm64: dts: lg: Fix SP805 clocks
  ARM: mstar: Fix up the fallout from moving the dts/dtsi files
  ARM: mstar: Add mstar prefix to all of the dtsi/dts files
  ARM: mstar: Add interrupt to pm_uart
  ARM: mstar: Add interrupt controller to base dtsi
  ARM: dts: meson8: remove two invalid interrupt lines from the GPU node
  arm64: dts: ti: k3-j7200-common-proc-board: Add USB support
  arm64: dts: ti: k3-j7200-common-proc-board: Configure the SERDES lane function
  arm64: dts: ti: k3-j7200-main: Add USB controller
  arm64: dts: ti: k3-j7200-main.dtsi: Add USB to SERDES lane MUX
  arm64: dts: ti: k3-j7200-main: Add SERDES lane control mux
  dt-bindings: ti-serdes-mux: Add defines for J7200 SoC
  ARM: dts: hisilicon: add SD5203 dts
  ARM: dts: hisilicon: fix the system controller compatible nodes
  arm64: dts: zynqmp: Fix leds subnode name for zcu100/ultra96 v1
  arm64: dts: zynqmp: Remove undocumented u-boot properties
  arm64: dts: zynqmp: Remove additional compatible string for i2c IPs
  arm64: dts: zynqmp: Rename buses to be align with simple-bus yaml
  ...

Pull ARM SoC-related driver updates from Olof Johansson:
 "Various driver updates for platforms. A bulk of this is smaller fixes
  or cleanups, but some of the new material this time around is:

   - Support for Nvidia Tegra234 SoC

   - Ring accelerator support for TI AM65x

   - PRUSS driver for TI platforms

   - Renesas support for R-Car V3U SoC

   - Reset support for Cortex-M4 processor on i.MX8MQ

  There are also new socinfo entries for a handful of different SoCs and
  platforms"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (131 commits)
  drm/mediatek: reduce clear event
  soc: mediatek: cmdq: add clear option in cmdq_pkt_wfe api
  soc: mediatek: cmdq: add jump function
  soc: mediatek: cmdq: add write_s_mask value function
  soc: mediatek: cmdq: add write_s value function
  soc: mediatek: cmdq: add read_s function
  soc: mediatek: cmdq: add write_s_mask function
  soc: mediatek: cmdq: add write_s function
  soc: mediatek: cmdq: add address shift in jump
  soc: mediatek: mtk-infracfg: Fix kerneldoc
  soc: amlogic: pm-domains: use always-on flag
  reset: sti: reset-syscfg: fix struct description warnings
  reset: imx7: add the cm4 reset for i.MX8MQ
  dt-bindings: reset: imx8mq: add m4 reset
  reset: Fix and extend kerneldoc
  reset: reset-zynqmp: Added support for Versal platform
  dt-bindings: reset: Updated binding for Versal reset driver
  reset: imx7: Support module build
  soc: fsl: qe: Remove unnessesary check in ucc_set_tdm_rxtx_clk
  soc: fsl: qman: convert to use be32_add_cpu()
  ...

Pull ARM SoC platform updates from Olof Johansson:
 "SoC changes, a substantial part of this is cleanup of some of the
  older platforms that used to have a bunch of board files.

  In particular:

   - Remove non-DT i.MX platforms that haven't seen activity in years,
     it's time to remove them.

   - A bunch of cleanup and removal of platform data for TI/OMAP
     platforms, moving over to genpd for power/reset control (yay!)

   - Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
     closer to multiplatform support (not quite there yet, but getting
     close).

  There are a few other changes too, smaller fixlets, etc. For new
  platform support, the primary ones are:

   - New SoC: Hisilicon SD5203, ARM926EJ-S platform.

   - Cpufreq support for i.MX7ULP"

* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
  ARM: mstar: Select MStar intc
  ARM: stm32: Replace HTTP links with HTTPS ones
  ARM: debug: add UART early console support for SD5203
  ARM: hisi: add support for SD5203 SoC
  ARM: omap3: enable off mode automatically
  clk: imx: imx35: Remove mx35_clocks_init()
  clk: imx: imx31: Remove mx31_clocks_init()
  clk: imx: imx27: Remove mx27_clocks_init()
  ARM: imx: Remove unused definitions
  ARM: imx35: Retrieve the IIM base address from devicetree
  ARM: imx3: Retrieve the AVIC base address from devicetree
  ARM: imx3: Retrieve the CCM base address from devicetree
  ARM: imx31: Retrieve the IIM base address from devicetree
  ARM: imx27: Retrieve the CCM base address from devicetree
  ARM: imx27: Retrieve the SYSCTRL base address from devicetree
  ARM: s3c64xx: bring back notes from removed debug-macro.S
  ARM: s3c24xx: fix Wunused-variable warning on !MMU
  ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
  MAINTAINERS: mark linux-samsung-soc list non-moderated
  ARM: imx: Remove remnant board file support pieces
  ...

Pull ARM SoC fixes from Olof Johansson:
 "I had queued up a batch of fixes that got a bit close to the release
  for sending in before the merge window opened, so I'm including them
  in the merge window batch instead.

  Mostly smaller DT tweaks and fixes, the usual mix that we tend to have
  through the releases"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
  ARM: dts: iwg20d-q7-common: Fix touch controller probe failure
  ARM: OMAP2+: Restore MPU power domain if cpu_cluster_pm_enter() fails
  ARM: dts: am33xx: modify AM33XX_IOPAD for #pinctrl-cells = 2
  soc: actions: include header to fix missing prototype
  arm64: dts: ti: k3-j721e: Rename mux header and update macro names
  soc: qcom: pdr: Fixup array type of get_domain_list_resp message
  arm64: dts: qcom: pm660: Fix missing pound sign in interrupt-cells
  arm64: dts: qcom: kitakami: Temporarily disable SDHCI1
  arm64: dts: sdm630: Temporarily disable SMMUs by default
  arm64: dts: sdm845: Fixup OPP table for all qup devices
  arm64: dts: allwinner: h5: remove Mali GPU PMU module
  ARM: dts: sun8i: r40: bananapi-m2-ultra: Fix dcdc1 regulator
  soc: xilinx: Fix error code in zynqmp_pm_probe()