Add a new function bnxt_alloc_vf_rep() to allocate a VF representor.
This function will be needed in subsequent patches to recreate the
VF reps after error recovery.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After probe is successful, interface may not be bought up in all
the cases and health register mapping could be invalid if firmware
undergoes reset. Fix it by invalidating the health register at the
end of probe. It will be remapped during ifup.

Fixes: 43a440c4 ("bnxt_en: Improve the status_reliable flag in bp->fw_health.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The retry loop in bnxt_try_recover_fw() should not abort when the
health register value is 0.  It is a valid value that indicates the
firmware is booting up.

Fixes: 861aae78 ("bnxt_en: Enhance retry of the first message to the firmware.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a comment spelling mistake "interfarence" -> "interference" in
function parse_nla_action(). Fix it.
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: David S. Miller <davem@davemloft.net>

The reset_prepare and reset_done calls have a null pointer check
on ae_dev however ae_dev is being dereferenced via the call to
ns3_is_phys_func with the ae->pdev argument. Fix this by performing
a null pointer check on ae_dev and hence short-circuiting the
dereference to ae_dev on the call to ns3_is_phys_func.

Addresses-Coverity: ("Dereference before null check")
Fixes: 715c58e9 ("net: hns3: add suspend and resume pm_ops")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The shifting of the u8 integers rq->caching by 26 bits to
the left will be promoted to a 32 bit signed int and then
sign-extended to a u64. In the event that rq->caching is
greater than 0x1f then all then all the upper 32 bits of
the u64 end up as also being set because of the int
sign-extension. Fix this by casting the u8 values to a
u64 before the 26 bit left shift.

Addresses-Coverity: ("Unintended sign extension")
Fixes: 4863dea3 ("net: Adding support for Cavium ThunderX network controller")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The shifting of the u8 integers f->fs.nat_lip[] by 24 bits to
the left will be promoted to a 32 bit signed int and then
sign-extended to a u64. In the event that the top bit of the u8
is set then all then all the upper 32 bits of the u64 end up as
also being set because of the sign-extension. Fix this by
casting the u8 values to a u64 before the 24 bit left shift.

Addresses-Coverity: ("Unintended sign extension")
Fixes: 12b276fb ("cxgb4: add support to create hash filters")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alex Elder says:

====================
net: ipa: support two more platforms

This series adds IPA support for two more Qualcomm SoCs.

The first patch updates the DT binding to add compatible strings.

The second temporarily disables checksum offload support for IPA
version 4.5 and above.  Changes are required to the RMNet driver
to support the "inline" checksum offload used for IPA v4.5+, and
once those are present this capability will be enabled for IPA.

The third and fourth patches add configuration data for IPA versions
4.5 (used for the SDX55 SoC) and 4.11 (used for the SD7280 SoC).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for the SC7280 SoC, which includes IPA version 4.11.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for the SDX55 SoC, which includes IPA version 4.5.

Starting with IPA v4.5, a few of the memory regions have a different
number of "canary" values; update comments in the where the region
identifers are defined to accurately reflect that.

I'll note three differences in SDX55 versus the other two existing
platforms (SDM845 and SC7180):
  - SDX55 uses a 32-bit Linux kernel
  - SDX55 has four interconnects rather than three
  - SDX55 uses IPA v4.5, which uses inline checksum offload
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Checksum offload for IPA v4.5+ is implemented differently, using
"inline" offload (which uses a common header format for both upload
and download offload).

The IPA hardware must be programmed to enable MAP checksum offload,
but the RMNet driver is responsible for interpreting checksum
metadata supplied with messages.

Currently, the RMNet driver does not support inline checksum offload.
This support is imminent, but until it is available, do not allow
newer versions of IPA to specify checksum offload for endpoints.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add existing supported platform "qcom,sc7180-ipa" to the set of IPA
compatible strings.  Also add newly-supported "qcom,sdx55-ipa",
"qcom,sc7280-ipa".
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Qiheng Lin <linqiheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Paolo Abeni  says:

====================
veth: allow GRO even without XDP

This series allows the user-space to enable GRO/NAPI on a veth
device even without attaching an XDP program.

It does not change the default veth behavior (no NAPI, no GRO),
except that the GRO feature bit on top of this series will be
effectively off by default on veth devices. Note that currently
the GRO bit is on by default, but GRO never takes place in
absence of XDP.

On top of this series, setting the GRO feature bit enables NAPI
and allows the GRO to take place. The TSO features on the peer
device are preserved.

The main goal is improving UDP forwarding performances for
containers in a typical virtual network setup:

(container) veth -> veth peer -> bridge/ovs -> vxlan -> NIC

Enabling the NAPI threaded mode, GRO the NETIF_F_GRO_UDP_FWD
feature on the veth peer improves the UDP stream performance
with not void netfilter configuration by 2x factor with no
measurable overhead for TCP traffic: some heuristic ensures
that TCP will not go through the additional NAPI/GRO layer.

Some self-tests are added to check the expected behavior in
the default configuration, with XDP and with plain GRO enabled.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add some basic veth tests, that verify the expected flags and
aggregation with different setups (default, xdp, etc...)
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After the previous patch, when enabling GRO, locally generated
TCP traffic experiences some measurable overhead, as it traverses
the GRO engine without any chance of aggregation.

This change refine the NAPI receive path admission test, to avoid
unnecessary GRO overhead in most scenarios, when GRO is enabled
on a veth peer.

Only skbs that are eligible for aggregation enter the GRO layer,
the others will go through the traditional receive path.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the veth device has the GRO feature bit set, even if
no GRO aggregation is possible with the default configuration,
as the veth device does not hook into the GRO engine.

Flipping the GRO feature bit from user-space is a no-op, unless
XDP is enabled. In such scenario GRO could actually take place, but
TSO is forced to off on the peer device.

This change allow user-space to really control the GRO feature, with
no need for an XDP program.

The GRO feature bit is now cleared by default - so that there are no
user-visible behavior changes with the default configuration.

When the GRO bit is set, the per-queue NAPI instances are initialized
and registered. On xmit, when napi instances are available, we try
to use them.

Some additional checks are in place to ensure we initialize/delete NAPIs
only when needed in case of overlapping XDP and GRO configuration
changes.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As described by commit 9c4c3252 ("skbuff: preserve sock
reference when scrubbing the skb."), orphaning a skb
in the TX path will cause OoO.

Let's use skb_orphan_partial() instead of skb_orphan(), so
that we keep the sk around for queue's selection sake and we
still avoid the problem fixed with commit 4bf9ffa0 ("veth:
Orphan skb before GRO")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Moshe Shemesh says:

====================
ethtool: Extend module EEPROM dump API

Ethtool supports module EEPROM dumps via the `ethtool -m <dev>` command.
But in current state its functionality is limited - offset and length
parameters, which are used to specify a linear desired region of EEPROM
data to dump, is not enough, considering emergence of complex module
EEPROM layouts such as CMIS 4.0.
Moreover, CMIS 4.0 extends the amount of pages that may be accessible by
introducing another parameter for page addressing - banks.

Besides, currently module EEPROM is represented as a chunk of
concatenated pages, where lower 128 bytes of all pages, except page 00h,
are omitted. Offset and length are used to address parts of this fake
linear memory. But in practice drivers, which implement
get_module_info() and get_module_eeprom() ethtool ops still calculate
page number and set I2C address on their own.

This series tackles these issues by adding ethtool op, which allows to
pass page number, bank number and I2C address in addition to offset and
length parameters to the driver, adds corresponding netlink
infrastructure and implements the new interface in mlx5 driver.

This allows to extend userspace 'ethtool -m' CLI by adding new
parameters - page, bank and i2c. New command line format:
 ethtool -m <dev> [hex on|off] [raw on|off] [offset N] [length N] [page N] [bank N] [i2c N]

The consequence of this series is a possibility to dump arbitrary EEPROM
page at a time, in contrast to dumps of concatenated pages. Therefore,
offset and length change their semantics and may be used only to specify
a part of data within half page boundary, which size is currently limited
to 128 bytes.

As for drivers that support legacy get_module_info() and
get_module_eeprom() pair, the series addresses it by implementing a
fallback mechanism. As mentioned earlier, such drivers derive a page
number from 'global' offset, so this can be done vice versa without
their involvement thanks to standardization. If kernel netlink handler
of 'ethtool -m' command detects that new ethtool op is not supported by
the driver, it calculates offset from given page number and page offset
and calls old ndos, if they are available.
====================

\Signed-off-by: David S. Miller <davem@davemloft.net>

If the device has a sfp bus attached, call its
sfp_get_module_eeprom_by_page() function, otherwise use the ethtool op
for the device. This follows how the IOCTL works.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The new netlink API for reading SFP data requires a new op to be
implemented. The idea of the new netlink SFP code is that userspace is
responsible to parsing the EEPROM data and requesting pages, rather
than have the kernel decide what pages are interesting and returning
them. This allows greater flexibility for newer formats.

Currently the generic SFP code only supports simple SFPs. Allow i2c
address 0x50 and 0x51 to be accessed with page and bank must always be
0. This interface will later be extended when for example QSFP support
is added.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case netlink get_module_eeprom_by_page() callback is not implemented
by the driver, try to call old get_module_info() and get_module_eeprom()
pair. Recalculate parameters to get_module_eeprom() offset and len using
page number and their sizes. Return error if this can't be done.
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@nvidia.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are two ways to retrieve information from SFP EEPROMs.  Many
devices make use of the common code, and assign the sfp_bus pointer in
the netdev to point to the bus holding the SFP device. Some MAC
drivers directly implement ops in there ethool structure.

Export within net/ethtool the two helpers used to call these methods,
so that they can also be used in the new netlink code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow the driver to recognise DSFP transceiver module ID and therefore
allow its EEPROM dumps using ethtool.
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement ethtool_ops::get_module_eeprom_by_page() to enable
support of new SFP standards.
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prepare for ethtool_ops::get_module_eeprom_data() implementation by
extracting common part of mlx5_query_module_eeprom() into a separate
function.
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Define get_module_eeprom_by_page() ethtool callback and implement
netlink infrastructure.

get_module_eeprom_by_page() allows network drivers to dump a part of
module's EEPROM specified by page and bank numbers along with offset and
length. It is effectively a netlink replacement for get_module_info()
and get_module_eeprom() pair, which is needed due to emergence of
complex non-linear EEPROM layouts.
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alex Elder says:

====================
net: ipa: a few small fixes

This series implements some minor bug fixes or improvements.

The first patch removes an apparently unnecessary restriction, which
results in an error on a 32-bit ARM build.

The second makes a definition used for SDM845 match what is used in
the downstream code.

The third just ensures two netdev pointers are only non-null when
valid.

The fourth simplifies a little code, knowing that a called function
never returns an error.

The fifth and sixth just remove some empty/place holder functions.

And the last patch fixes a comment, makes a function private, and
removes an unnecessary double-negation of a Boolean variable.  This
patch produces a warning from checkpatch, indicating that a pair of
parentheses is unnecessary.  I agree with that advice, but it
conflicts with a suggestion from the compiler.  I left the "problem"
in place to avoid the compiler warning.
====================

Link: https://lore.kernel.org/r/20210409180722.1176868-1-elder@linaro.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Some time ago changes were made to stop referring to clearing the
hardware pipeline as a "tag process."  Fix a comment to use the
newer terminology.

Get rid of a pointless double-negation of the Boolean toward_ipa
flag in ipa_endpoint_config().

make ipa_endpoint_exit_one() private; it's only referenced inside
"ipa_endpoint.c".
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

There are place holder functions in the GSI code that do nothing.
Remove these, knowing we can add something back in their place if
they're really needed someday.

Some of these are inverse functions (such as teardown to match setup).
Explicitly comment that there is no inverse in these cases.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

There are place holder functions in the IPA code that do nothing.
For the most part these are inverse functions, for example, once the
routing or filter tables are set up there is no need to perform any
matching teardown activity at shutdown, or in the case of an error.

These can be safely removed, resulting in some code simplification.
Add comments in these spots making it explicit that there is no
inverse.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In ipa_modem_stop(), if the modem netdev pointer is non-null we call
ipa_stop().  We check for an error and if one is returned we handle
it.  But ipa_stop() never returns an error, so this extra handling
is unnecessary.  Simplify the code in ipa_modem_stop() based on the
knowledge no error handling is needed at this spot.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In ipa_modem_start(), we set endpoint netdev pointers before the
network device is registered.  If registration fails, we don't undo
those assignments.  Instead, wait to assign the netdev pointer until
after registration succeeds.

Set these endpoint netdev pointers to NULL in ipa_modem_stop()
before unregistering the network device.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

On IPA v3.5.1, the sequencer type for the modem TX endpoint does not
define the replication portion in the same way the downstream code
does.  This difference doesn't affect the behavior of the upstream
code, but I'd prefer the two code bases use the same configuration
value here.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

I no longer know why a validation check ensured the size of an entry
passed to gsi_trans_pool_init() was restricted to be a multiple of 8.
For 32-bit builds, this condition doesn't always hold, and for DMA
pools, the size is rounded up to a power of 2 anyway.

Remove this restriction.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Conflicts:

MAINTAINERS
 - keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
 - simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
 - trivial
include/linux/ethtool.h
 - trivial, fix kdoc while at it
include/linux/skmsg.h
 - move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
 - add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
 - trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Even if the current mapping is correct for the 1 CPU and 2 CPU cases
(currently enetc is included in SoCs with up to 2 CPUs only), better
use a generic rule for the mapping to cover all possible cases.
The number of CPUs is the same as the number of interrupt vectors:

Per device Tx rings -
device_tx_ring[idx], where idx = 0..n_rings_total-1

Per interrupt vector Tx rings -
int_vector[i].ring[j], where i = 0..n_int_vects-1
			     j = 0..n_rings_per_v-1

Mapping rule -
n_rings_per_v = n_rings_total / n_int_vects
for i = 0..n_int_vects - 1:
	for j = 0..n_rings_per_v - 1:
		idx = n_int_vects * j + i
		int_vector[i].ring[j] <- device_tx_ring[idx]
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20210409071613.28912-1-claudiu.manoil@nxp.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The blamed commit introduced a bit in the TX software buffer descriptor
structure for determining whether a BD is final or not; we rearm the TX
interrupt vector for every frame (hence final BD) transmitted.

But there is a problem with the patch: it replaced a condition whose
expression is a bool which was evaluated at the beginning of the "while"
loop with a bool expression that is evaluated on the spot: tx_swbd->is_eof.

The problem with the latter expression is that the tx_swbd has already
been incremented at that stage, so the tx_swbd->is_eof check is in fact
with the _next_ software BD. Which is _not_ final.

The effect is that the CPU is in 100% load with ksoftirqd because it
does not acknowledge the TX interrupt, so the handler keeps getting
called again and again.

The fix is to restore the code structure, and keep the local bool is_eof
variable, just to assign it the tx_swbd->is_eof value instead of
!!tx_swbd->skb.

Fixes: d504498d ("net: enetc: add a dedicated is_eof bit in the TX software BD")
Reported-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20210409192759.3895104-1-olteanv@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Saeed Mahameed says:

====================
mlx5-next 2021-04-09

This pr contains changes from  mlx5-next branch,
already reviewed on netdev and rdma mailing lists, links below.

1) From Leon, Dynamically assign MSI-X vectors count
Already Acked by Bjorn Helgaas.
https://patchwork.kernel.org/project/netdevbpf/cover/20210314124256.70253-1-leon@kernel.org/

2) Cleanup series:
https://patchwork.kernel.org/project/netdevbpf/cover/20210311070915.321814-1-saeed@kernel.org/

From Mark, E-Switch cleanups and refactoring, and the addition
of single FDB mode needed HW bits.

From Mikhael, Remove unused struct field

From Saeed, Cleanup W=1 prototype warning

From Zheng, Esw related cleanup

From Tariq, User order-0 page allocation for EQs

* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
  net/mlx5: Implement sriov_get_vf_total_msix/count() callbacks
  net/mlx5: Dynamically assign MSI-X vectors count
  net/mlx5: Add dynamic MSI-X capabilities bits
  PCI/IOV: Add sysfs MSI-X vector assignment interface
  net/mlx5: Use order-0 allocations for EQs
  net/mlx5: Add IFC bits needed for single FDB mode
  net/mlx5: E-Switch, Refactor send to vport to be more generic
  RDMA/mlx5: Use representor E-Switch when getting netdev and metadata
  net/mlx5: E-Switch, Add eswitch pointer to each representor
  net/mlx5: E-Switch, Add match on vhca id to default send rules
  net/mlx5: Remove unused mlx5_core_health member recover_work
  net/mlx5: simplify the return expression of mlx5_esw_offloads_pair()
  net/mlx5: Cleanup prototype warning
====================

Link: https://lore.kernel.org/r/20210409200704.10886-1-saeed@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This loop will try to unmap enetc_unmap_tx_buff[-1] and crash.

Fixes: 9d2b68cc ("net: enetc: add support for XDP_REDIRECT")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/YHBHfCY/yv3EnM9z@mwandaSigned-off-by: Jakub Kicinski <kuba@kernel.org>